Manual Craftsman 247.88664

49 pages 3.55 mb
Download

Go to site of 49

Summary
  • Craftsman 247.88664 - page 1

    Owner's Manual 5 Horse Power 24" Two-Stage Snow Thrower Model No. 247.886640 CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. • Safety • Assembly • _peration • Service ° Maintenance • EspaSol, p. 30 Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A. Visit our we ...

  • Craftsman 247.88664 - page 2

    Content Page Warranty Information ......................................... 2 Safe Operation Practices ................................... 3 Assembly ........................................................... 5 Operation ........................................................... 8 Maintenance ...................................................... ...

  • Craftsman 247.88664 - page 3

    _lb WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this sym ...

  • Craftsman 247.88664 - page 4

    7. Muffler and engine become hot and can cause a burn. Do not touch. 8. Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic. 9. Exercise caution when changing direction and while operating on slopes. 10. Plan your snow-throwing pattern toavoid discharge towards windows, walls, cars etc. T ...

  • Craftsman 247.88664 - page 5

    Unpacking 1. Remove screws from the top sides and ends of the shipping crate. 2. Set crate panels aside to avoid tire punctures or personal injury. 3. Remove and discard plastic bag that covers unit. 4. Remove any loose parts included with unit (i.e., Operator's Manual, etc). 5. Roll unit out of crate. Hardware Pack Following items make up the ...

  • Craftsman 247.88664 - page 6

    Figure 3 10. Take a "Z" fitting from the hardware pack and insert the Z end into the hole on the left clutch grip on the handle panel. See Figure 4. Thread a hex nut from hardware pack on to the Z fitting. P Hex Nut Figure 4 11. Route the left cable between engine and speed selector plate and then between handle panel and clutch lever piv ...

  • Craftsman 247.88664 - page 7

    1. Locate the shave plate in Figure 6. The space between this shave plate and ground can be adjusted. 2. For close snow removal on smooth surface, raise skid shoes higher. See Figure 5. 3. Place skid shoes in middle or lower position when the area to be cleared is uneven. See Figure 5. 4. Adjust skid shoes by loosening the four hex nuts and carriag ...

  • Craftsman 247.88664 - page 8

    Operating Controls Be familiar with all the controls and their proper operation. See Figure 6 and follow descriptions given below. Know how to stop the machine and disengage them quickly. Chute ( Traction Control Shift Leve_ ger Control Gas Fill Discharge Chute Chute Directional ,.--Control Auger Plate *_Skid Shoe Figure 6 Shift Lever The shift lev ...

  • Craftsman 247.88664 - page 9

    Before Starting _ WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. Fill Oil 1. The engine was shipped with oil. Check the oil level before operating. After the initial use, you will have to fill up as necessary. Be careful not to overfill. 2. Before filling up gas in the engine ...

  • Craftsman 247.88664 - page 10

    Frozen Recoil Starter If the starter is frozen and wilt not turn the engine, proceed as follows: 1. Pull as much rope out of the starter as possible. 2. Release the starter handle and let it snap back against the starter. 3. If the engine still fails to start, repeat the first two steps. If continued attempts do not free starter, follow the electri ...

  • Craftsman 247.88664 - page 11

    General Recommendations Always observe safety rules when performing any maintenance. The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain the snow thrower as instructed in this manual. Follow the maintenance schedule given bel ...

  • Craftsman 247.88664 - page 12

    lubricant. Avoid oil spillage on rubber friction wheel and aluminum drive plate. Lever Lube Gear Sha_ friction wheel and drive plate Figure 8 Chute Directional Control: The worm gear on the chute control should be lubricated with multi- purpose automotive grease. Auger Shaft: At least once a season, remove shear bolts on auger shaft. Oil or spray l ...

  • Craftsman 247.88664 - page 13

    2. Visually inspect for frayed, cracked, or excessively Electrodes worn out belts. .030" Porcelain Gap Figure 10 Tire Pressure Maintain equal pressure on both tires. For more details on this, follow instructions on page 7. Check V-Belts Follow instructions below to check the condition of the drive belts every 50 hours of operation. 1. Remove t ...

  • Craftsman 247.88664 - page 14

    i_hl WARNING: Before servicing, repairing, or inspecting, disengage allclutch levers and stop engine. Wait until all moving parts have come toa complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. All adjustments in the Service and Adjustments section of this manual should be checked at least on ...

  • Craftsman 247.88664 - page 15

    5. Unhook the idler spring from the hex bolt on the auger housing. See Figure 14. 6. Unhook the support bracket spring from the frame. NOTE: It may be necessary to loosen the six nuts that connect frame to auger housing to aid in belt removal. 7. Lift the auger belt from the auger pulley, and slip belt between the support bracket and the auger pull ...

  • Craftsman 247.88664 - page 16

    Making Adjustments _bb WARNING: Never attempt to make any adjustments while the engine is running, except where specified in operator's manual. Chute Assembly The distance snow is thrown can be controlled by adjusting the angle of the top section of the chute assembly. Skid Shoe The space between the shave plate and the ground can be adjusted. ...

  • Craftsman 247.88664 - page 17

    If the snow thrower wilt not be used for30 days or longer, or at the end ofthe snow season when the last possibility ofsnow is gone, the equipment needs to be stored properly. _b WARNING: Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, ...

  • Craftsman 247.88664 - page 18

    Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel, Engine runs erratic Water or dirt in fuel system, Loss of power Spark plug wire loose, Gas cap vent hole plugged. Exhaust port plugged. Engine overheats Carburetor not adjusted properly. Blocked fuel line, Choke not in ON position Faulty spark plug. Ke ...

  • Craftsman 247.88664 - page 19

    Tecumseh Servicing Dealer or bycontacting Tecumseh Products Co., c/o Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, W153024-1499. Telephone 1-262- 377-2700 [or in USA/Canada call 1-800-558-5402] or see your local telephone yellow pages under "Engines, Gasoline" for the name, address and telepho ...

  • Craftsman 247.88664 - page 20

    CRAFTSMAN 5.0 HP SNOW THROWER MODEL 247.886640 6_ 6_ 14 13 14 / 65 36 / 4O .41 28 / 3O /43 / 44 47 20 ...

  • Craftsman 247.88664 - page 21

    CRAFTSMAN 5.0 HP SNOW THROWER MODEL 247.886640 Key No. Part No. 1, 731-04426 2, 712-3068 3, 736-0159 4, 710-0451 5, 710-04071 6, 736-0159 7, 720-0284 8, 731-1300B 9, 712-3027 10. 712-3010 11. 736-0242 12. 784-5647 13. 741-0475 14. 712-3027 15. 731-0851A 16. 731-1379C 17. 710-0451 18. 05931A 19. 736-0119 21. 710-3015 22. 710-0703 23. 741-0309 25. 73 ...

  • Craftsman 247.88664 - page 22

    CRAFTSMAN 5.0 HP SNOW THROWER MODEL 247.886640 20 24 4 6 I1 .31 36 ® "48 22 ...

  • Craftsman 247.88664 - page 23

    CRAFTSMAN 5.0 HP SNOW THROWER MODEL 247.886640 Key No. Part No. 1, 710-1652 2, 731-1324 3, 4, 732-0339 5, 710-3005 6, 05896A 7, 748-0234 8, 710-0627 10. 710-1245B 11. 736-0242 12. 736-0505 13. 736-0507 14. 756-0967 15. 748-0360 16. 746-0897 17. 738-0281 18. 736-0167 19. 732-0611 20. 756-0569 21. 754-0343 23. 736-0247 24. 736-0331 25. 710-0696 26. 7 ...

  • Craftsman 247.88664 - page 24

    CRAFTSMAN 5.0 HP SNOW THROWER MODEL 247.886640 24 21 "14 8 2 • 3 3O / 31 33 35 45 / 44 / 38 / / 39 _42 43 24 ...

  • Craftsman 247.88664 - page 25

    CRAFTSMAN 5.0 HP SNOW THROWER MODEL 247.886640 Key No. Part No. 1, 726-0100 2, 720-0201A 3, 705-5204A 4, 747-0697 5, 710-0599 6, 710-0449 7, 736-0451 8, 710-0262 9, 712-0429 10. 749-0953A 749-0952A 11. 710-0643 12. 736-0119 13. 712-3027 14. 720-0274 15. 710-0788 16. 710-3015 17. 732-0733 18. 747-0904 19. 705-5231 20. 720-0284 21. 705-5233A 705-5234 ...

  • Craftsman 247.88664 - page 26

    CRAFTSMAN 5.0 HP ENGINE 143.045001 FOR SNOW THROWER MODEL 247.886640 275_ 364, _2-3ol 219 370B 262 400 t328 26 ...

  • Craftsman 247.88664 - page 27

    CRAFTSMAN 5.0 HP ENGINE 143.045001 FOR SNOW THROWER MODEL 247.886640 Key No. Part No. Description Key No. Part No. 0 RPM High 3450 to 3750 126 32644A 0 RPM Low 1850 to 2150 126 32645A 1 36469A Cylinder (Incl. 2,20,72 & 125) 127 650691 2 26727 Dowel Pin 130 6021A 4 0 Oil Drain Extn. (Purchase Local) 130A 650694A 5 30969 Extension Cap 130B 650818 ...

  • Craftsman 247.88664 - page 28

    CRAFTSMAN 5.0 HP ENGINE 143.045001 FOR SNOW THROWER MODEL 247.886640 Table continued from Key No. 351 355 364 364A 365 370A 370B 370C 370D Pad No. 32180C 590574 33333 37673 650735 36261 35282 36501 35878 age 27 Description Primer Line Starter Handle (Mitten Grip) Carburetor Cover Bracket Lock Plate Screw, 10-24 x 3/8" Lubrication Decal Instruc ...

  • Craftsman 247.88664 - page 29

    CRAFTSMAN 5.0 HP ENGINE 143.045001 FOR SNOW THROWER MODEL 247.886640 Rewind Starter 590707 12 ' Key No. 0 1 2 3 4 5 6 7 8 11 12 13 Part No. 590707 590599A 590600 590696 590601 590697 590698 590699 590709 590708 590535 590574 Description Rewind Starter Spring Pin Washer Retainer Washer Brake Spring Starter Dog Dog Spring Pulley & Rewind Spr ...

  • Craftsman 247.88664 - page 30

    Contenido P_g. Informaci6n sobre la garantia ............................ 30 Pr&cticas de seguridad en la operaci6n ............. 31 Ensamblado ....................................................... 33 Operaci6n .......................................................... 36 Mantenimiento ................................................... 39 Co ...

  • Craftsman 247.88664 - page 31

    _lb ADVERTENClA: Este simbolo indica instrucciones de seguridad importantes que de no seguirse, podrian poner en peligro la seguridad personal y!o la propieclad suya y de terceros. Lea y siga todas las instrucciones en este manual antes de iniciar la operaciOn de esta maquina. En caso de no seguir estas instrucciones podrian producirse lesiones per ...

  • Craftsman 247.88664 - page 32

    4. Nunca opere la m_quina si falta un canal de descarga o el mismo est_ dafiado. Mantenga todos los dispositivos de seguridad en su lugar yen funcionamiento. 5. Nunca encienda el motor en espacios cerrados o en una zona poco ventilada. El escape del motor contiene mon6xido de carbono, un gas inodoro y letaL 6. No opere la m_quina estando bajo los e ...

  • Craftsman 247.88664 - page 33

    Desempaque 1. Retire los tornillos de los lades y extremos superiores de la caja de embalaje. 2. Retire los paneles de la caja para evitar que se pinchen las Ilantas o que se produzcan lesiones personales. 3. Retire y descarte la bolsa de pl&stico que cubre la unidad. 4. Quite cualquier parte suelta que se incluya con su unidad (por ejemplo, el ...

  • Craftsman 247.88664 - page 34

    ,iral deberia engranar los dientes del canal aqu[ Figura 3 10. Tome un accesorio "Z" del paquete de hardware e inserte el extremo "Z" dentro del orificio en la empuSadura del embrague izquierdo del panel de la manija, Ver la Figura 4. Enrosque una tuerca hexagonal del paquete de hardware en el accesorio "Z." _ Empufiad ...

  • Craftsman 247.88664 - page 35

    4, Ajuste las zapatas antideslizantes aflojando las cuatro tuercas hexagonales y los pernos de carro tal come se muestra en Figura 5. Mueva las zapatas antideslizantes a la posici6n deseada. 5, Compruebe que toda la superficie inferior de las zapatas antideslizantes est6 contra el suelo para evitar un desgaste despareje de las mismas. Vuelva a ajus ...

  • Craftsman 247.88664 - page 36

    Controles de operacibn Familiaricese con todos los controles y su operaci6n apropiada. Yea Figura 6 y siga las descripciones que se indican debajo. Sepa c6mo detener la maquina y c6mo desengranar los controles rapidamente. Herramienta de limpieza del canal Control de tracci6n ;ontrol de la barrena cambios Llenado de gasolina Canal de desca_ Silen ...

  • Craftsman 247.88664 - page 37

    Antes de encender ,_ ADVERTENCIA: Lea, comprenda y siga todas las instrucciones y advertencias que aparecen en la maquina yen este manual antes de operarla. Llenado de aceite 1. El motor se envia sin aceite. Compruebe el nivel de aceite antes de operar. Despu6s del uso inicial, tendr_ que tlenarlo hasta el nivel necesario. Tenga cuidado de no Ilena ...

  • Craftsman 247.88664 - page 38

    posici6n OFF. Si el motor falla, gire hacia el obturador FULL. luego mueva lentamente hacia posici6n OFF. Arrancador de retroceso congelado Si el arrancador est_ congelado y no enciende el motor, proceda de la siguiente manera: 1. Saque la mayor cantidad de coerda posible del arrancador. 2. Suelte la manija del arrancador y deje que golpee contra e ...

  • Craftsman 247.88664 - page 39

    Recomendaciones generales Respete siempre las reglas de seguridad cuando realice tareas de mantenimiento. La garantia de esta m_quina quitanieve no cubre elementos que hart estado sujetos al real uso o negligencia del operador. Para recibir el reembolso total de la garantia, el operador deber_ dar mantenimiento a la m_quina quitanieve como se indic ...

  • Craftsman 247.88664 - page 40

    Palanca de cambios Engranaje Eje Evite colocar aceite en _er_de. 1rlcclon yen la placa de transmisi6n Figura 8 Control direccional del canal: El engranaje helicoidal del control del canal deberia ser lubricado con grasa automotor multiuso, Eje de la barrena: AI menos una vez por temporada, quite los pernos de cuchilla del eje de la barren& Lubr ...

  • Craftsman 247.88664 - page 41

    Electrodos .030" Distancia Porcelana Figura 10 Presibn de los neum ticos Mantenga la misma presi6n en ambos neum_ticos. Para obtener m_s detalles, siga las instrucciones en la p_gina 35. Compruebe las correas en V Siga las instrucciones a continuaci6n para verificar el estado de las correas de transmisi6n cada 50 horas de funcionamiento. 1. Sa ...

  • Craftsman 247.88664 - page 42

    Correas de las barrenas Rueda de fricci6n Ensamblado Pasador 1. Saque la cubierta pl&stica de la correa ubicada en el frente del motor. Para ello saque los dos tomillos autoroscantes, Ver Figura 12, Cubierta Autosellante Tornillos Figura 12 2, Drene gasolina de la m_quina quitanieve o coloque un pedazo de pl&stico debajo de la tapa de gasol ...

  • Craftsman 247.88664 - page 43

    _ ADVERTENCIA: Desconecte la bujia y p6ngala de manera que haga masa contra et motor. Drene combustible a un recipiente aprobado o ubique una pieza de pelicula pl&stica debajo del tap6n de combustible para evitar que pierda gasotina. 3, Saque las chavetas de trinquete que sujetan las ruedas y saque las ruedas del eje, 4. Utilizando una Ilave al ...

  • Craftsman 247.88664 - page 44

    Control de la barrena Para ajustar el embrague de la barren& consulte la secci6n Ensamblado y Ajustes Finales en la p_gina 34. Ruedas de transmisibn Es posible ajustar las ruedas para dos m_todos de operaci6n diferentes. Siga los pasos que aparecen debajo para realizar los ajustes. Ver Figura 19. Figura 19 Transmision de una rueda 1. En el lade ...

  • Craftsman 247.88664 - page 45

    Problema Causa Solucibn El motor no arranca 1. El dep6sito de combustible est_ vacio o el combustible es viejo. 2. La linea del combustible est_ bloqueada, 3. La palanca de obturaci6n no est_ en la posici6n ON (encendido). 4. La bujia nofunciona correctamente. 5. La Ilave de seguridad no se encuentra en el interruptor de encendido del motor, 6. Se ...

  • Craftsman 247.88664 - page 46

    Declaracibn de garantia del Control de emisiones de EPA para California y Estados Unidos La Agencia estadounidense de proteccidn del medio ambiente ("EPA"), el Consejo de recursos a_reos de California ("CARB") y Tecumseh Products Co. se complacen en explicar la Garantia de los sistemas federales y de California para el control d ...

  • Craftsman 247.88664 - page 47

    Tecumseh Products Co. en cumplimiento del inciso 4 siguiente. Todas las piezas mencionadas reparadas o reemplazadas segQn la Garantia del sistema de control de emisiones (Garantia ECS) seran garantizadas pot todo el resto del Periodo de la Garantia del sistema de control de emisiones (Garantia ECS). 2. Todas las piezas garantizadas relacionadas con ...

  • Craftsman 247.88664 - page 48

    Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door o ...

  • Craftsman 247.88664 - page 49

    LITERATURE - LIS COVERSHEET Total Pages: _L_ Total Models:' Paper doc: # Notes: ! Pdf doc: / /1 Workflow - LITERATURE _ /_"iL_/_ (_(_}o 2=/ -z Initial and Date each section below as it is completed: Received Batched Scanried TA Index QA/IE L0308228 NUMBER: FIGURE PROPERTIES Tit,e: ___,_ _ _ _ _ - _ _ L_ _ a_ _- Chassis: Prod Type: _ _ _: ...

Manufacturer Craftsman Category Snow Blower

Documents that we receive from a manufacturer of a Craftsman 247.88664 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 247.88664 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 247.88664
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 247.88664.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 247.88664, service manual, brief instructions and user manuals Craftsman 247.88664. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 247.88664.

Similar manuals

A complete manual for the device Craftsman 247.88664, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 247.88664 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 247.88664.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 247.88664 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 247.88664, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 247.88664, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 247.88664 - which should help us in our first steps of using Craftsman 247.88664
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 247.88664
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 247.88664 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 247.88664?

Use the form below

If you did not solve your problem by using a manual Craftsman 247.88664, ask a question using the form below. If a user had a similar problem with Craftsman 247.88664 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)