Manual King Canada 9818-RJ

32 pages 1.42 mb
Download

Go to site of 32

Summary
  • King Canada 9818-RJ - page 1

    Sea-King Fully S t abilized Marine Satellite System 9815-RJ 9818-RJ Inst allation and Operating Instructions 1 1200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www .kingcontrols.com 1315 REV A Satellite Solutions for Mobile Markets MEMBER ® ® ...

  • King Canada 9818-RJ - page 2

    ...

  • King Canada 9818-RJ - page 3

    Page 1 IMPORT ANT! The satellite TV market is exp anding and changing. The information in this manual was accurate at the time of printing. If your Sea-King System does not operate as outlined in this manual please call King Controls at (800) 982-9920 or visit our website at www .kingcontrols.com. T ABLE OF CONTENTS Section Contents Page 1. INTRODU ...

  • King Canada 9818-RJ - page 4

    The Sea-King Fully S t abilized Marine Satellite System includes 4 main components (Fig. 1) . Dome (Antenna) Unit Mounted on the vessel. The dish is covered by a protective dome that keeps operational component s free from the elements. Controller Located in the vessel. Used to activate and monitor the system, and access programming and diagnostic ...

  • King Canada 9818-RJ - page 5

    AZIMUTH: Angle in degrees measured clockwise from Magnetic North (0°) (Fig. 2) . SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission. SECTION 2 DEFINITION OF TERMS Fig. 3 ELEV A TION: Angle in degrees measured from the ground plane (Fig. 3) . Page 3 Fig. 2 ...

  • King Canada 9818-RJ - page 6

    KIT CONTENTS: 1. Unpack and identify all component s (Fig. 4) . Page 4 SECTION 3 INST ALLA TION TOOLS AND MA TERIALS REQUIRED: - drill and drill bit set - tape measure - 7/16” open end wrench (coax connections) - 5/32” allen wrench, channel lock or pliers (to remove shipping bolt) - 1/8” allen wrench or phillips screw driver (to remove dome c ...

  • King Canada 9818-RJ - page 7

    Page 5 DOME LOCA TION 1. Select an area on the vessel for the dome unit, keeping in mind the coax cables will enter the vessel through the surface directly beneath the dome unit. Use the following criteria: a) The shortest distance between the dome unit and the main satellite receiver is most desirable. b) The dome unit requires either a 16.5 inch ...

  • King Canada 9818-RJ - page 8

    1. Remove and save the dome cover screws. (Figs. 6A and 6B) . 2. Carefully remove the dome cover , tilting it side to side as necessary to prevent damaging internal components. 3. Remove and discard the shipping bolt. Page 6 COMPONENT LOCA TION: 1. Select the location of the internal components using the following criteria: a) The Controller , T un ...

  • King Canada 9818-RJ - page 9

    Page 7 Fig. 6A Fig. 6B 9815-RJ 9818-RJ IMPORT ANT! The shipping bolt must be removed prior to inst allation. IMPORT ANT! CAREFULL Y remove the dome cover , tilting it side to side as necessary to prevent damaging internal component s. IMPORT ANT! The shipping bolt must be removed prior to inst allation. IMPORT ANT! CAREFULL Y remove the dome cover ...

  • King Canada 9818-RJ - page 10

    ELECTRICAL HAZARD W ARNING! T o verify proper operation of the components in their selected locations, perform a System Location check as follows: 5. Connect system as outlined in Fig. 10, Page 13 . 6. V erify system operates properly as described in Section 4 OPERA TION, Page 18 . 7. After verifying proper operation of the system, disconnect all c ...

  • King Canada 9818-RJ - page 11

    DOME INST ALLA TION AND EXTERNAL WIRING Fig. 7 IMPORT ANT! USE ONL Y THE COAXIAL CABLES SUPPLIED WITH THE SEA-KING . DO NOT CUT COAX. COIL AND ST ORE EXCESS CABLE IN THE CABINET WITH THE COMPONENTS. If coaxial cable other than that supplied with the Sea-King is used, the following guide lines must be followed: 1) Ends must be terminated with SNAP-N ...

  • King Canada 9818-RJ - page 12

    Fig. 8 Page 10 IMPORT ANT! The inst aller is responsible for weatherproofing all holes in the vessel. Note: The installer is responsible for determining the most appropriate fastener to secure the dome unit to the pedestal or vessel surface. Depending on the surface material, fasteners such as lag screws, well nuts, sheet met al screws, toggle bolt ...

  • King Canada 9818-RJ - page 13

    IMPORT ANT! Coax connection will slide inside rubber sleeve. Coax connections should be snug. DO NOT OVER TIGHTEN! Gel-filled boot s must sit flush against rubber sleeve. Fig. 9 4. Run coax cable(s) from the dome unit to the location where they will enter the vessel. Secure coax every 12-18 inches. 5. Drill 3/4” hole in the vessel where the tuner ...

  • King Canada 9818-RJ - page 14

    ELECTRICAL HAZARD W ARNING! Page 12 INTERNAL WIRING (Fig. 10) 1. Connect the 50’ coax cable from “MAIN” on dome unit to the tuner port labeled “ANT .” 2. Connect the 7’ coax from the tuner port labeled “REC” to the main satellite receiver port labeled “SA TELLITE IN.” 3. Connect the 7’ controller cable from the controller to t ...

  • King Canada 9818-RJ - page 15

    Page 13 9815-RJ 9818-RJ WIRING DIAGRAM Fig. 10 IMPORT ANT! A VOID SHARP BENDS WHEN ROUTING COAX. ...

  • King Canada 9818-RJ - page 16

    Page 14 MUL TIPLE SA TELLITE RECEIVER CONFIGURA TIONS With the use of an active multi-switch (not supplied by King Controls), more than two TV’ s and receivers can be hooked up (see Fig. 1 1 for typical 4 receiver hookup). Other options: 3-4 satellite receivers: use one 2x4 or 3x4 active multi-switch 8 satellite receivers: use one 2x8 or 3x8 acti ...

  • King Canada 9818-RJ - page 17

    Page 15 Fig. 1 1 TYPICAL 4 RECEIVER HOOKUP IMPORT ANT! A VOID SHARP BENDS WHEN ROUTING COAX. ...

  • King Canada 9818-RJ - page 18

    The Faceplate is optional and can be removed as follows: (Fig. 13) 1. Remove 4 screws from Controller . 2. Slide Faceplate off of Controller . 3. Replace 4 screws. Page 16 OPTIONAL W ALL MOUNT F ACEPLA TE (INCLUDED) 1. Use the Faceplate as a template to mark and cut out the mounting cavity , and if necessary , mark and drill the mounting holes (Fig ...

  • King Canada 9818-RJ - page 19

    3. Mount tuner in previously chosen location (Fig 15) . Page 17 OPTIONAL TUNER MOUNTING BRACKETS (INCLUDED) 1. Remove 4 screws from the tuner . 2. Fasten mounting brackets to tuner with same screws (Fig. 14) . Fig. 14 Fig. 15 Note: Depending on the mounting surface, pilot holes for the fasteners may or may not need to be drilled. Note: The installe ...

  • King Canada 9818-RJ - page 20

    IMPORT ANT! There must be a clear “line of sight” to the satellite (See Fig. 2, Page 3). T errain, other boat s, buildings, trees, mast s, telephone poles, etc. can all block the satellite signal from reaching the dish. SECTION 4 OPERA TION Note: This example is for the DTV 101 satellite in Region 2-North Central. The information on your contro ...

  • King Canada 9818-RJ - page 21

    REGION OPTIONS: 1 NORTH WEST 2 NORTH CENTRAL 3 NORTH EAST 4 CENTRAL WEST 5 MIDDLE CENTRAL 6 CENTRAL EAST 7 SOUTH WEST 8 SOUTH CENTRAL 9 SOUTH EAST ALL REGIONS 0 RECALIBRA TE Page 19 Note: T o reduce satellite acquisition time, you can set your current region. SET REGION (OPTIONAL) ...

  • King Canada 9818-RJ - page 22

    Page 20 SET SA TELLITE SERVICE SA TELLITE OPTIONS DISH 61 Dish Network at 61 EXPVU 91 Bell ExpressV u at 91 DISH 129 Dish Network at 129 DISH 148 Dish Network at 148 EXPVU 82 Bell ExpressV u at 82 DTV 101 DIRECTV at 101 Sat 1 10 Dish Network at 1 10 Sat 1 19 Dish Network at 1 19 DTV 101/ 1 10 hd DIRECTV at 101 and 1 10 DTV 101/ 1 19 DIRECTV at 101 ...

  • King Canada 9818-RJ - page 23

    Page 21 Note: For DIRECTV Subscribers: The satellite setting allows the user to select the satellite and service provider of choice. For DIRECTV subscribers, the Sea-King can also track a secondary or alternate satellite. Example: If you are a subscriber to the DIRECTV service most of the programming that you will be watching will be transmitted fr ...

  • King Canada 9818-RJ - page 24

    Page 22 SECTION 5 TROUBLESHOOTING SYMPTOM POSSIBLE SOLUTION Controller does not power up. Check: tuner is connected to power supply . controller is connected to tuner . power supply is plugged into 1 10 V AC outlet. Controller remains in one of the following conditions: POWER TRIP ANT COM ERROR? TUNER COM ERROR? Unplug tuner for 10 seconds, then pl ...

  • King Canada 9818-RJ - page 25

    Page 23 SYMPTOM POSSIBLE SOLUTION Only getting signal on 1/2 of transponders. Kinked or sharply bent coax cable. V erify coax cables are tightly crimped with F-compression style crimps only . V erify receiver is operating properly . V erify LNB type is set correctly . Unit never locks on or locks on and drift s off of satellite. Atmospheric moistur ...

  • King Canada 9818-RJ - page 26

    Page 24 OPTION 21 RE-INITIALIZE and 0-RECALIBRA TE ...

  • King Canada 9818-RJ - page 27

    Page 25 ...

  • King Canada 9818-RJ - page 28

    Page 26 MECHANICAL CALIBRA TION IMPORT ANT! Y ou must call King Controls before performing this procedure. IMPORT ANT! The Sea-King must remain perfectly still during the mechanical calibration. The Sea-King must be running (NOT IN IDLE/HOLD). ...

  • King Canada 9818-RJ - page 29

    Page 27 The Sea-King Satellite System has been designed to be maintenance and trouble free. For optimum signal strength, keep the dome clean from dirt, bugs, and other debris. Periodic washing of the dome with mild soap and water is recommended. If you plan on storing your vessel for long periods of time, it is recommended that the system be put th ...

  • King Canada 9818-RJ - page 30

    Page 28 Every King Controls Satellite System is thoroughly inspected and tested before leaving the factory . It is covered by a two year part s and one year labor limited warranty from the date of original purchase. This warranty does not cover installation and external wiring or refurbished unit s. Should any trouble develop during the warranty pe ...

  • King Canada 9818-RJ - page 31

    ...

  • King Canada 9818-RJ - page 32

    1 1200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www .kingcontrols.com ® ...

Manufacturer King Canada Category Satellite TV System

Documents that we receive from a manufacturer of a King Canada 9818-RJ can be divided into several groups. They are, among others:
- King Canada technical drawings
- 9818-RJ manuals
- King Canada product data sheets
- information booklets
- or energy labels King Canada 9818-RJ
All of them are important, but the most important information from the point of view of use of the device are in the user manual King Canada 9818-RJ.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals King Canada 9818-RJ, service manual, brief instructions and user manuals King Canada 9818-RJ. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product King Canada 9818-RJ.

Similar manuals

A complete manual for the device King Canada 9818-RJ, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use King Canada 9818-RJ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of King Canada 9818-RJ.

A complete King Canada manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual King Canada 9818-RJ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the King Canada 9818-RJ, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the King Canada 9818-RJ, that we can find in the current document
3. Tips how to use the basic functions of the device King Canada 9818-RJ - which should help us in our first steps of using King Canada 9818-RJ
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with King Canada 9818-RJ
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of King Canada 9818-RJ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning King Canada 9818-RJ?

Use the form below

If you did not solve your problem by using a manual King Canada 9818-RJ, ask a question using the form below. If a user had a similar problem with King Canada 9818-RJ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)