English dropdown-ico

Manual Chamberlain RDO800

24 pages 2.56 mb
Download

Go to site of 24

Summary
  • Chamberlain RDO800 - page 1

    Installa tion an d operating instr u ctions for rolling d oor opener Mo d el RDO800-series Chamberlain GmbH Alfred-Nobel-S trasse 4 66793 Saarwellingen Germany TEL: +49 (0) 6838/907-250 F AX: +49 (0) 6838/907-179 www .liftmaster .com ...

  • Chamberlain RDO800 - page 2

    1 The Protector System must be used for all installations where the closing force as measured on the bottom of the door is over 400N (40kgf). Excessive force will interfere with the proper operation of the Safety Reverse System or damage the garage door . After installation, ensure that the parts of the door do not extend over public footpaths or r ...

  • Chamberlain RDO800 - page 3

    2 Door Requirements 3 Ensure that there is at least 45mm from the edge of the curtain to the edge of the bracket. If the roller door drums are on the edge of the curtain or are of small diameter additional clearance maybe required. If the drums are more than 60mm from the curtain edge or of small diameter extension poles maybe required. Different d ...

  • Chamberlain RDO800 - page 4

    3 Prepare Opener 5 For left hand side installations the wire jumper should be removed . Place the Opener in Manual Release mode. Pull the release cord down and across to engage the ball into the cup. The drive forks should now be able to be moved manually . NOTE: T o re-engage the opener , pull the release cord across and up. For right hand side in ...

  • Chamberlain RDO800 - page 5

    4 Installation steps 6 FOR RIGHT HAND INST ALLA TIONS (REFER SECTION 5, page 3) 1. Ensure that the opener position jumper (wire connector) is in place (refer section 5, page 3). 2. Place the opener in manual release mode (refer section 5, page 3). 3. Open the roller door fully . For safety , tie a rope around the door . 4. Ensure that the U-bolt on ...

  • Chamberlain RDO800 - page 6

    Pinning the Door 9 Use bolts or pop-rivet s (not supplied) to hold the curt ain to the door drum. 1. Pull the release cord down and across to engage the ball into the cup. Close the door manually . Pull the release cord across and release to re-engage the opener . 2. T ry to manually open the door with the opener engaged. Any excess door curtain ma ...

  • Chamberlain RDO800 - page 7

    6 Program your Opener & Remote Please note your remote controls and wall plate have already been programmed into your operator . Activate the opener only when door is in full view , free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s) ...

  • Chamberlain RDO800 - page 8

    7 Setting the Force The force, as measured on the closing edge of the door , should not exceed 400N (40kgf). If the closing force is measured to more than 400N, the Protector System must be installed. See section 14. The force setting regulates the amount of power required to open and close the door . 1. Press the purple button (1) twice to enter o ...

  • Chamberlain RDO800 - page 9

    8 CARE OF YOUR OPENER When properly installed, your opener will provide high performance with a minimum of maintenance. The opener does not require additional lubrication. Limit and Force Settings: These settings must be checked and properly set when the opener is installed. W eather conditions may cause some minor changes in the door operation, re ...

  • Chamberlain RDO800 - page 10

    9 Troubleshooting 1. The opener doesn't operate from either the green start button or the remote controls: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1. • Is there a build-up of ice o ...

  • Chamberlain RDO800 - page 11

    10 OPERATION OF YOUR OPENER Y our opener can be activated by any of the following devices: • The green start button Hold the button down until door start s to move. • The W all Control, Outside Keylock or Keyless Entry System (if you have installed any of these accessories). • The Remote Control Transmitter or W ireless Wall Control (128LM) H ...

  • Chamberlain RDO800 - page 12

    GARAGE DOOR OPENER W ARRANTY Chamberlain warrants to the first retail purchaser of this product that the product shall be free from any defect in materials and/or workmanship for a period of 24 full months (2 years) from the date of purchase. Upon receipt of the product, the first retail purchaser is under obligation to check the product for any vi ...

  • Chamberlain RDO800 - page 13

    Installa tion and operating instr uctions for rolling door opener Model RDO800GB Chamberlain GmbH Alfred-Nobel-S trasse 4 66793 Saarwellingen Germany TEL: +49 (0) 6838/907-250 F AX: +49 (0) 6838/907-179 www .liftmaster .com ...

  • Chamberlain RDO800 - page 14

    1 The Protector System must be used for all installations where the closing force as measured on the bottom of the door is over 400N (40kgf). Excessive force will interfere with the proper operation of the Safety Reverse System or damage the garage door . After installation, ensure that the parts of the door do not extend over public footpaths or r ...

  • Chamberlain RDO800 - page 15

    2 Door Requirements 3 Ensure that there is at least 45mm from the edge of the curtain to the edge of the bracket. If the roller door drums are on the edge of the curtain or are of small diameter additional clearance maybe required. If the drums are more than 60mm from the curtain edge or of small diameter extension poles maybe required. Different d ...

  • Chamberlain RDO800 - page 16

    3 Prepare Opener 5 For left hand side installations the wire jumper should be removed . Place the Opener in Manual Release mode. Disengage: Pull the release cord down once until you hear a clicking sound. The operator is now in manual mode and may be opened or closed. Engage: T o re-engage the opener , pull the release cord down until you hear a cl ...

  • Chamberlain RDO800 - page 17

    4 Installation steps 6 FOR RIGHT HAND INST ALLA TIONS (REFER SECTION 5, page 3) 1. Ensure that the opener position jumper (wire connector) is in place (refer section 5, page 3). 2. Place the opener in manual release mode (refer section 5, page 3). 3. Open the roller door fully . For safety , tie a rope around the door . 4. Ensure that the U-bolt on ...

  • Chamberlain RDO800 - page 18

    Pinning the Door 9 Use bolts or pop-rivet s (not supplied) to hold the curt ain to the door drum. 1. Pull the release cord down and across to engage the ball into the cup. Close the door manually . Pull the release cord across and release to re-engage the opener . 2. T ry to manually open the door with the opener engaged. Any excess door curtain ma ...

  • Chamberlain RDO800 - page 19

    6 Program your Opener & Remote Please note your remote controls and wall plate have already been programmed into your operator . Activate the opener only when door is in full view , free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s) ...

  • Chamberlain RDO800 - page 20

    7 Setting the Force The force, as measured on the closing edge of the door , should not exceed 400N (40kgf). If the closing force is measured to more than 400N, the Protector System must be installed. See section 14. The force setting regulates the amount of power required to open and close the door . 1. Press the purple button (1) twice to enter o ...

  • Chamberlain RDO800 - page 21

    8 CARE OF YOUR OPENER When properly installed, your opener will provide high performance with a minimum of maintenance. The opener does not require additional lubrication. Limit and Force Settings: These settings must be checked and properly set when the opener is installed. W eather conditions may cause some minor changes in the door operation, re ...

  • Chamberlain RDO800 - page 22

    9 Troubleshooting 1. The opener doesn't operate from either the green start button or the remote controls: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1. • Is there a build-up of ice o ...

  • Chamberlain RDO800 - page 23

    10 OPERATION OF YOUR OPENER Y our opener can be activated by any of the following devices: • The green start button Hold the button down until door start s to move. • The W all Control, Outside Keylock or Keyless Entry System (if you have installed any of these accessories). • The Remote Control Transmitter or W ireless Wall Control (128LM) H ...

  • Chamberlain RDO800 - page 24

    GARAGE DOOR OPENER W ARRANTY Chamberlain warrants to the first retail purchaser of this product that the product shall be free from any defect in materials and/or workmanship for a period of 24 full months (2 years) from the date of purchase. Upon receipt of the product, the first retail purchaser is under obligation to check the product for any vi ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain RDO800 can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- RDO800 manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain RDO800
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain RDO800.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain RDO800, service manual, brief instructions and user manuals Chamberlain RDO800. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain RDO800.

Similar manuals

A complete manual for the device Chamberlain RDO800, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain RDO800 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain RDO800.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain RDO800 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain RDO800, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain RDO800, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain RDO800 - which should help us in our first steps of using Chamberlain RDO800
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain RDO800
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain RDO800 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain RDO800?

Use the form below

If you did not solve your problem by using a manual Chamberlain RDO800, ask a question using the form below. If a user had a similar problem with Chamberlain RDO800 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)