English dropdown-ico

Manual Miller Electric GP30

19 pages 1.79 mb
Download

Go to site of 19

Summary
  • Miller Electric GP30 - page 1

    1242 ARIZONA AVE. LARCHWOOD, IA 51241 1-800-570-82 05 GP30 LO ADER P ARTS and INSTRUCTIONS O WNER’S MANU AL ...

  • Miller Electric GP30 - page 2

    TO PREVENT POSSIBLE ROLLOVER, OBSERV E T HE FOLLOWING SAFETY PR ECAUTIONS ♦ Carry loads as low as poss ible ♦ Drive tractor slowly when turning, operating on hills or inclines, or traversing un- even ground ♦ Raise load to fu ll height only w hen tractor in on even ground and fr ont wheels are straight ahead TO PREVENT POSSIBLE PERSONAL INJUR ...

  • Miller Electric GP30 - page 3

    T ABLE OF CONTENTS • Composite Bearing Information • Mounting Loader on T ractor • Dismounting Loader • Quick-attach Instructions • Parts Schematics • Cylinder Packing Detail • Loader S pecifications • W arranty SERIAL No. of Loader Purchased ______________________ _ Date Purchased____________________ ...

  • Miller Electric GP30 - page 4

    COMPOSITE BEARING INFORMA TION FIGURE A . Your GP/GL-Series loader is equipp ed with composite, greaseless bearings at all (12) pivot points. These high-quality bearings should not be confused with plastic bushings, sintered bushin gs, or meta l-backed bearings. Compos ite bearings are made from an ultra-strong fiberglass composite that has t w ice ...

  • Miller Electric GP30 - page 5

    MOUNTING LOADER STEP 1 For a new loader installation, the mountings must be installed on th e tractor first. Refer to the typical mounting kit shown in Figure 1. A detailed schematic of your specific kit is available—just call 1-800-570-8205 if the schematic was not included with yo ur new loader. STEP 2 The loader should have been dismounted (or ...

  • Miller Electric GP30 - page 6

    DISMOUNTING LOADER STEP 1 DRIVE THE TRACTOR ON TO FLAT CONCRETE and place the loader in the position shown in Fig 1. STEP 2 Remove the stand legs fro m their stored position and place them in their dismount positio n. Slide th e in- ner tubes down to the extended position and secu re them with the 3/4” pins. See Fig. 2. FIG. 1 STEP 3 Gently lower ...

  • Miller Electric GP30 - page 7

    QUICK-A TT A CH INSTRUCTIONS UNCOUPLING 1. Raise sliding latches as show n in Figure 1. 2. Rotate QT pins out of the lower notches, ra ise, an d then rotate them into the upper notche s of the sliding latc hes as shown in Figure 2. 3. Slide the sliding latches do w n as shown in Fi gure 3. This secures the QT pins in the “up” position so they d ...

  • Miller Electric GP30 - page 8

    1 8 15 19 29 10 15 19 16 14 17 30 36 27 28 13 12 35 3 26 18 2 11 9 31 32 29 34 33 29 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 MF30 MAINFRAME, GL30/GP30 1 2 QT30 QUICK ATTACH FRAME 1 3C Y - 0 5 9 CYLINDER, BUCKET, GL/GP 3 0 2 8 PN-600AC16 PIN, CHROME 2" x 6" WITH RETAINER 2 9 PN-700AC16 PIN, CHROME 2" x 7" WITH RETAINER 2 10 PN-65 ...

  • Miller Electric GP30 - page 9

    ITEM NO. PART NUMBER DESCRIPTION with bearings/QTY. 20 BR-2500K-3750 COMPOSITE BEARING, 2.00 BORE, 3.75 LONG 2 21 PS-2000-45 Pin Seal (MRW), 2.0 ID x 2.5 OD x 5/16 Thick 8 22 BR-2000K-1500 COMPOSITE BEARING, 1.50 BORE, 1.50 LONG 2 23 BR-2500K-3125 COMPOSITE BEARING, 2.00 BORE, 3.125 LONG 2 11 59.886 DWG. NO. SHEET REV. DATE MAINF RAME, GL30/GP30 OF ...

  • Miller Electric GP30 - page 10

    ITEM NO. PART NUMBER DESCRIPTION Pin Up Latch Up/QTY. 1 QT02-01L SLIDING LATCH ASSY, QT, LH 1 2 QT02-01R SLIDING LATCH ASSY, QT, RH 1 3 QT02-14 RETAINING PIN ASSEMBLY, QT 2 4 QT30-W WELDED QT FRAME 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 4 HW-NS-06-A NUT, 3/8-16 UNC, CL, ZN 4 5 HW-SP-01 SPRING, QT HANDLE 4 6 HW-WS-06-A WASHER, 3/8, FLAT, ZN 4 DWG. ...

  • Miller Electric GP30 - page 11

    DWG. NO. SHEET REV. DATE GL30/GP30 HOSES & PIPING OF 1 A 1/1 3/2005 HP30 1 SCHE MATIC WEIGHT: 23.706 ITEM NO. PART NUMBER DESCRIPTION with pipes/QTY. 1 HP30P-BL BUCKET TILT FEEDLINE, LOWER 1 2 HP30P-BU BUCKET TILT FEEDLINE, UPPER 1 3 HP30P-LL LIFT FEEDLINE, LOWER 1 4 HP30P-LU LIFT FEEDLINE, UPPER 1 5 PC06X2 PIPE CLAMP 7 6 HP30-HBL BUCKET CYL I ...

  • Miller Electric GP30 - page 12

    ITEM NO. PART NUMBER DESCRIPTION with aux kit/QTY. 24 HP30P-GU AUXILLARY FEEDLINE, UPPER 1 25 HP30P-GL AUXILLARY FEEDLINE, LOWER 1 26 SF-2706-LN-10-08 BULKHEAD CONNECTOR, -10 JIC to 1/2 NPT 2 27 PC06X2 PIPE CLAMP 9 28 HW-BS-05-0100-A BOLT, 5/16-18 UNC, GR5 ZN, 1" LONG 9 29 HW-LS-05-A LOCKWASHER, 5/16, ZN 9 30 HOSE SPECIFY LENGTH REQUIRED 2 31 ...

  • Miller Electric GP30 - page 13

    3 2 1 7 8 6 7 5 4 9 7 8 7 6 ITEM NO. PART NUMBER DESCRIPTION Stand Legs/QTY. 1 SL30-TL TOP TUBE ASSY, LEFT 1 2 SL30-BL BOTTOM TUBE ASSY, STAND LEG (LH) 1 3 SL30-HL STAND LEG HANDLE, LEFT 1 4 SL30-TR TOP TUBE ASSY, RIGHT 1 5 SL30-BR BOTTOM TUBE ASSY, STAND LEG (RH) 1 6 PIN1-006 CLEVIS PIN, 3/4 X 3 1/2 ZNC 2 7 P IN1-017 HAIRPIN COTTER, 2-11/16 LONG 6 ...

  • Miller Electric GP30 - page 14

    ITEM NO. PART NUMBER DESCRIPTION QTY. 1 CY-059T TUBE ASSEMBLY, GP/GL25-30 BUCKET 1 2 CY-059D ROD ASSY, GL/GP30 BUCKET 1 3 CP-GL-3017-S GLAND, 3017, SHORT-TAIL 1 4 CP-PS-3017-U PISTON, 3017 U-CUP 1 5 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAI N 1 6 CP-KT-3017-U P-KIT, 3.000 X 1.750 UC 1 7 PS-1500-45 Pin Seal (MRW), 1. 50 I D x 2.0 OD x 5/16 Thick 4 8 ...

  • Miller Electric GP30 - page 15

    3 4 2 5 1 7 NOTES: 1 . BEAR ING AND SEALS SOLD SE PARATELY. 2. PACKING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING. 3. EAR LY CYLIN DER S (1 2/04-2/05) WERE 1 " SHOR TER AN D HAD 1 " LESS STROKE . SEE NOTE 1 8 8 DWG. NO. SHEET DATE LIFT CYLINDER, GP30, LH OF 1 1/ 28/2005 CY -060 -L 1 SCH EMATI C ALL DIMENSIONS IN INC HES 85.856 BORE ...

  • Miller Electric GP30 - page 16

    ITEM NO. PART NUMBER DESCRIPTION QTY. 1 CY-058D ROD ASSEMBLY, GL/GP30 LIFT 1 2 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAIN 1 3 CY-060-RT TUBE ASSEMBLY, GP30 LIFT, RH 1 4 CP-GL-3520-L GLAND, 3520 LONG-TAIL 1 5 CP-PS-3520-U PISTON, 3520 U-CUP 1 6 CP-KT-3520-U P-KIT, 3. 500 X 2.000 UC 1 7 BR-2000K-3125 COMPOSITE BEARING, 1. 50 BORE, 3.125 LONG 1 8 PS-15 ...

  • Miller Electric GP30 - page 17

    ROD WIPER PISTON GLA ND SEA L, U-CUP, LARGE SEAL, U-CU P, SM ALL O-RING, SMA LL O-RING, LARGE B/U WA SHER SNAP RI NG SCHE MATIC DWG. NO. SHEET REV. DATE PACKING CONFIGURAT ION, U-CUP OF 1 A 1/1 3/2005 CP-KT-U 1 WEIGHT: FRONT OF CYLINDER ...

  • Miller Electric GP30 - page 18

    14’−8" 13’−6" 2’−11" 34° 44° 11’−10" 8" 100" TYPICAL GP30 SPECIFICA TIONS SPECIFICATIONS AND PERFORMANCE NUM BERS ARE FOR REFERENCE ONLY WEIGHT S: Loader (less bucket and mounts) : 2090 lbs. 8 FT Bucket : 800 lbs. Mounting Kit (Typical) : 710 lbs. Total : 3600 lbs. LIFTING CAPACITY: Breakaway Lift : 7 ...

  • Miller Electric GP30 - page 19

    WARRANTY Dec 2004 ALL PRODUCTS MANUFACTURED BY MI LLER LOADERS, INCOPRORATED ( MLI ) EXCEPT THE CHROME-PLATED PIVOT PINS USED ON GR EASELESS LOADERS, ARE GUARENTEED TO THE ORIGINAL PURCHASER FOR A PERIOD OF ONE YEAR FROM THE DAY OF PURCHASE AGAINST ANY DEFECTS IN MATERIALS AND WORKMANSHIP OF FARM LOADERS AND ATTACHMENTS THAT ARE USED IN NORMAL FARM ...

Manufacturer Miller Electric Category Compact Loader

Documents that we receive from a manufacturer of a Miller Electric GP30 can be divided into several groups. They are, among others:
- Miller Electric technical drawings
- GP30 manuals
- Miller Electric product data sheets
- information booklets
- or energy labels Miller Electric GP30
All of them are important, but the most important information from the point of view of use of the device are in the user manual Miller Electric GP30.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Miller Electric GP30, service manual, brief instructions and user manuals Miller Electric GP30. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Miller Electric GP30.

Similar manuals

A complete manual for the device Miller Electric GP30, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Miller Electric GP30 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Miller Electric GP30.

A complete Miller Electric manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Miller Electric GP30 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Miller Electric GP30, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Miller Electric GP30, that we can find in the current document
3. Tips how to use the basic functions of the device Miller Electric GP30 - which should help us in our first steps of using Miller Electric GP30
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Miller Electric GP30
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Miller Electric GP30 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Miller Electric GP30?

Use the form below

If you did not solve your problem by using a manual Miller Electric GP30, ask a question using the form below. If a user had a similar problem with Miller Electric GP30 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)