Manual Kenwood TK-270G

35 pages 0.35 mb
Download

Go to site of 35

Summary
  • Kenwood TK-270G - page 1

    INSTRUCTION MANUAL MODE D’EMPLOI MANUAL DE INSTRUCCIONES BEDIENUNGSANLEITUNG MANUAL DI ISTRUZIONI GEBRUIKSAANWIJZING A 3 2 1 B 6 5 4 C 9 8 7 D 0 KENWOOD CORPORA TION © B62-1294-30 (E,NE,NT) 09 08 07 06 05 04 03 TK-270G/ TK-370G VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER EMETTEUR-RECEPTEUR FM VHF/ EMETTEUR-RECEPTEUR FM UHF TRANSCEPTOR DE FM VHF/ TRAN ...

  • Kenwood TK-270G - page 2

    TK-270G/ TK-370G VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ENGLISH ...

  • Kenwood TK-270G - page 3

    i W ARNING: EXPLOSIVE A TMOSPHERES (GASES, DUST , FUMES, etc.) T urn off your transceiver while taking on fuel, or while parked in gasoline service stations. ◆ GOVERNMENT LAW PROHIBITS THE OPERA TION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. ◆ ILLEGAL OPERA TION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BO ...

  • Kenwood TK-270G - page 4

    ii PRECAUTIONS Observe the following precautions to prevent fire, personal injury , and transceiver damage. • Do not modify this transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it close to heating appliances. • Do not place the transceiver in excessively dusty , humid, and/or wet areas ...

  • Kenwood TK-270G - page 5

    iii CONTENTS UNP ACKING AND CHECKING EQUIPMENT ................... 1 Supplied Accessories ...................................... 1 PREP ARATION .................................................. 3 Charging the Optional NiCd Battery Pack .................. 3 Installing/ Removing the Optional NiCd Battery Pack ..... 3 Installing the Antenna ......... ...

  • Kenwood TK-270G - page 6

    iv Storing DTMF Numbers .................................... 1 6 Confirming Stored DTMF Numbers ..................... 16 Dialling Stored DTMF Numbers ......................... 17 Clearing Stored DTMF Numbers .......................... 1 7 Redialling .................................................. 1 7 CODE SQUELCH ................................ ...

  • Kenwood TK-270G - page 7

    1 UNP ACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer , an authorized KENWOOD service facility , or the factory . Carefully unpack the transceiver . We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or ha ...

  • Kenwood TK-270G - page 8

    2 Belt clip Speaker/ microphone jacks cap Screw set Speaker/ microphone locking bracket Antenna (TK-270G) Antenna (TK-370G) ...

  • Kenwood TK-270G - page 9

    3 PREP ARA TION ■ Charging the Optional NiCd Battery Pack The optional battery pack is not charged at the factory; charge it before use (refer to the battery pack instruction manual). ◆ DO NOT RECHARGE THE BA TTER Y P ACK IF IT IS ALREADY FULL Y CHARGED. DOING SO MA Y CAUSE THE LIFE OF THE BA TTER Y P ACK TO SHOR TEN OR THE BA TTER Y P ACK MA Y ...

  • Kenwood TK-270G - page 10

    4 1 Match the four grooves of the battery pack with the corresponding guides on the back of the transceiver . 2 Slide the battery pack along the back of the transceiver until the release latch on the base of the transceiver locks. 3 To remove the battery pack, pull back on the release latch and slide the pack away from the transceiver . Screw the a ...

  • Kenwood TK-270G - page 11

    5 ■ Installing the Belt Clip If necessary , attach the belt clip using the two supplied 3 x 8 mm screws. Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment. If you are not using an optional speaker/ microphone, install the cover over the SP/MIC jacks ...

  • Kenwood TK-270G - page 12

    6 A 3 2 1 B 6 5 4 C 9 8 7 D 0 GETTING ACQUAINTED q q q q q e e e e e r r r r r t t t t t y y y y y u u u u u i i i i i o o o o o !0 !0 !0 !0 !0 w w w w w Antenna Microphone Speaker The transceiver is shown with the optional KNB-14 battery pack. q q q q q Rotary encoder Y our dealer can program the encoder as either Group Up/Down or Channel Up/Down ...

  • Kenwood TK-270G - page 13

    7 e e e e e Power switch/ V olume control T urn clockwise to switch ON the transceiver . Rotate to adjust the volume. T o switch OFF the transceiver , turn counterclockwise fully . r r r r r PTT (Push-to-T alk) switch Press this switch, then speak into the microphone to call a station. t t t t t Side 1 key This is a PF (Programmable Function) key . ...

  • Kenwood TK-270G - page 14

    8 n o c I n o i t p i r c s e D . r e v i e c s n a r t s i h t n o d e s u t o N s i l e n n a h c d e t c e l e s e h t n e h w s r a e p p A . y s u b , e n o T - 2 , F M T D , T Q D , T Q n e h w s r a e p p A y b ( d e t a v i t c a e d s i g n i d o c e d e n o T - 5 r o e h t g n i s s e r p r o t i n o M . ) y e k e d o C a e v i e c e r u ...

  • Kenwood TK-270G - page 15

    9 PROGRAMMABLE AUXILIAR Y FUNCTIONS Side 1 , Side 2 , O , ● , t t t t t , and s s s s s can be programmed with the auxiliary functions listed below . n o i t c n u F e n o T - 2 / F M T D l e d o M l e d o M e n o T - 5 1 l l a Co Ns e Y 2 l l a Co Ns e Y n w o D l e n n a h Cs e Ys e Y p U l e n n a h Cs e Ys e Y r e t c a r a h C y a l p s i Ds ...

  • Kenwood TK-270G - page 16

    10 OPERA TING BASICS ■ Switching Power ON/OFF T urn the Power switch/ V olume control clockwise to switch the transceiver ON. T urn the Power switch/ V olume control counter- clockwise to switch the transceiver OFF . If the Radio Password function is programmed, “P ASSWORD” will appear on the display when the power is turned ON. T o unlock th ...

  • Kenwood TK-270G - page 17

    11 ■ Adjusting the Squelch Level Squelch is used to silence the speaker when no signals are present. When squelch is turned OFF , you will hear background noise from the speaker . When it is ON, you will not hear background noise. The squelch level you select determines when squelch will turn OFF and ON. If you select a squelch level that is too ...

  • Kenwood TK-270G - page 18

    12 ■ Placing a Call 1 Make sure no parties are currently transmitting on your selected channel. 2 Press the PTT switch and speak into the microphone in your normal speaking voice. • For best sound quality at the receiving station, hold the microphone approximately 1.5 inches (3 ~ 4 cm) from your mouth. 3 Release the PTT switch to receive. ■ R ...

  • Kenwood TK-270G - page 19

    13 CHANNEL SCAN Scan is useful for monitoring signals on the channels programmed on the transceiver . When scanning, the transceiver checks for a signal on each channel, and only stops on a channel if a signal is present. The transceiver will remain on a busy channel until the signal is no longer present. Y our dealer programs the delay time betwee ...

  • Kenwood TK-270G - page 20

    14 ■ Priority Scan If your dealer set up a priority channel on your transceiver , the transceiver will continuously monitor that channel while receiving a signal on another channel. When a signal is received on the Priority channel, the transceiver immediately switches to that channel. • “P” appears on the display . The transceiver will rem ...

  • Kenwood TK-270G - page 21

    15 DTMF CALLS ■ Manual Dialling There are two ways to manually call a number: 1) Press and hold the PTT switch, then enter the desired digits on the keypad. •Y ou can enter the digits 0 ~ 9 , A ~ D , , and # . ( A ~ D may be disabled by your dealer .) • If programmed by your dealer , you do not need to continuously hold the PTT switch. The tr ...

  • Kenwood TK-270G - page 22

    16 ■ Storing DTMF Numbers Note: Auto Dialling must first be activated by your dealer . Y ou can store DTMF numbers (16 digits maximum) in each of the 9 Auto Dial memory locations (1 ~ 9). 1 Press the # key . • “D” appears on the display . 2 Enter the desired digits on the keypad. •Y ou can enter the digits 0 ~ 9 , A ~ D , , and # . ( A ~ ...

  • Kenwood TK-270G - page 23

    17 ■ Dialling Stored DTMF Numbers To call a number stored in a memory location: 1 Press the key . • “A” appears on the display . 2 Enter the desired memory location number ( 1 ~ 9 ) . • The stored digits are displayed. 3 Press the PTT switch. • If programmed by your dealer , no DTMF tone will sound when “D” is transmitted. “D” i ...

  • Kenwood TK-270G - page 24

    18 CODE SQUELCH Code Squelch is enabled or disabled by your dealer . This function turns the transceiver squelch OFF only when it receives the DTMF code that has been set up in your transceiver . T ransceivers that do not transmit the correct code will not be heard. Consequently , you can communicate with a specific party without listening to other ...

  • Kenwood TK-270G - page 25

    19 ■ T ransmitting 1 Press and hold the PTT switch. 2 Enter the code of the transceiver you want to call or enter a Group code on the keypad. • If desired, you can send codes the same way you make DTMF calls {page 15}. Both manual methods can be used or you can store codes in memory , then dial them from a memory location. • “CALL” appear ...

  • Kenwood TK-270G - page 26

    20 SELECTIVE CALL Selective Call is enabled or disabled by your dealer . This function is similar to Code Squelch {page 18}. The differences from Code Squelch are: •Y ou can send or receive message codes containing a maximum of 5 digits. • Selective Call turns the squelch OFF only when the transceiver receives a predetermined DTMF code in the c ...

  • Kenwood TK-270G - page 27

    21 ■ Receiving When you receive the correct ID and Intermediate codes, squelch turns OFF and you will hear the call. If a message code is also received, the message appears on the display • “CALL” appears on the display and the LED indicator flashes orange. • When you receive a call with your ID code, “C” appears on the display (i.e.- ...

  • Kenwood TK-270G - page 28

    22 ■ T ransmitting 1 Press and hold the PTT switch. 2 Enter the code of the transceiver you want to call or enter a Group code on the keypad. • Be sure to enter the ID or Group code, followed by the Intermediate code of the transceiver you want to call. If desired, you can also enter a message code of up to 5 digits. • If desired, you can sen ...

  • Kenwood TK-270G - page 29

    23 2-TONE SIGNALLING 2-T one Signalling is enabled or disabled by your dealer . This function turns the transceiver optional signalling OFF only when it receives the 2-tone signal that has been set up in your transceiver . T ransceivers that do not transmit the correct tones will not be heard. Y our dealer may also activate Group Call for your tran ...

  • Kenwood TK-270G - page 30

    24 ■ T ransmitting 1 Press the key programmed as 2-T one Encode . •A 2-T one code appears on the display . 2 Rotate the Rotary encoder to select your desired 2-T one code. 3 Press the PTT switch and 2-T one Encode key to begin transmitting. Release the 2-T one Encode key when transmission has started. Release the PTT switch to receive. • When ...

  • Kenwood TK-270G - page 31

    25 5-TONE SIGNALLING 5-T one Signalling is either activated or deactivated by your dealer . 5-T one Signalling only opens the squelch when the transceiver receives five tones corresponding to those set up in your transceiver . When the squelch opens, you will be able to hear the caller without any further action. After a correct 5-T one signal is r ...

  • Kenwood TK-270G - page 32

    26 AUXILIARY FUNCTIONS ■ Selecting an Output Power Each channel is programmed with either high or low output power by your dealer . Y ou can change the output power of only channels programmed as high. When you can reliably communicate with other parties without using high power , select low power by pressing the key programmed as RF Power Lo . E ...

  • Kenwood TK-270G - page 33

    27 ■ Busy Channel Lockout (BCL) The Busy Channel Lockout feature is activated or deactivated by your dealer . When activated, BCL prevents you from interfering with other parties who may be using the same channel that you selected. Pressing the PTT switch while the channel is in use will cause your transceiver to emit an alert tone and transmissi ...

  • Kenwood TK-270G - page 34

    28 ■ Battery Voltage Level While transmitting, the transceiver automatically checks the battery voltage level. When the voltage level becomes low , the LED indicator flashes red. When a tone sounds, transmission stops. Recharge or replace the battery pack at this time. ■ Lamp Press the key programmed as Lamp to toggle the display backlight ON o ...

  • Kenwood TK-270G - page 35

    29 ■ Monitor/Squelch Y our dealer can program a key with the Monitor or Squelch function one of four ways: Squelch Momentary: Press and hold the Squelch key to hear background noise. Release the key to return to normal operation. Squelch Off: Momentarily press the Squelch key to hear background noise. Press the key again to return to normal opera ...

Manufacturer Kenwood Category Radio

Documents that we receive from a manufacturer of a Kenwood TK-270G can be divided into several groups. They are, among others:
- Kenwood technical drawings
- TK-270G manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood TK-270G
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood TK-270G.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood TK-270G, service manual, brief instructions and user manuals Kenwood TK-270G. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood TK-270G.

Similar manuals

A complete manual for the device Kenwood TK-270G, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood TK-270G by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood TK-270G.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood TK-270G - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood TK-270G, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood TK-270G, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood TK-270G - which should help us in our first steps of using Kenwood TK-270G
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood TK-270G
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood TK-270G in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood TK-270G?

Use the form below

If you did not solve your problem by using a manual Kenwood TK-270G, ask a question using the form below. If a user had a similar problem with Kenwood TK-270G it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)