Manual D-Link DFL-2560G

483 pages Not applicable
Download

Go to site of 483

Summary
  • D-Link DFL-2560G - page 1

    Network Security Sol ution http://www .dlink.com Security Security DFL-210/ 800/1600/ 2500 DFL-260/ 860/1660/ 2560(G) V er. 1.10 Network Security F irewall User Manu al ...

  • D-Link DFL-2560G - page 2

    User Manual DFL-210/260/800/860/1600/1660/2500/2560/2560G NetDefendOS Version 2.26 D-Link Corporation No. 289, Sinhu 3rd Rd, Neihu District, Taipei City 114, Taiwan R.O.C. http://www.DLink.com Published 2009-09-08 ...

  • D-Link DFL-2560G - page 3

    User Manual DFL-210/260/800/860/1600/1660/2500/2560/2560G NetDefendOS Version 2.26 Published 2009-09-08 Copyright Notice This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced ...

  • D-Link DFL-2560G - page 4

    Table of Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1. NetDefendOS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • D-Link DFL-2560G - page 5

    3.3. Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 3.3.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • D-Link DFL-2560G - page 6

    5.2. DHCP Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 5.3. Static DHCP Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • D-Link DFL-2560G - page 7

    7.3.6. Multiple SAT Rule Matches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 7.3.7. SAT and FwdFast Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 8. User Authentication . . . . . . . . . . ...

  • D-Link DFL-2560G - page 8

    10.1.11. A Summary of Traffic Shaping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 10.1.12. More Pipe Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 10.2. IDP Traffic Shaping . . . . . . . . . . . . . ...

  • D-Link DFL-2560G - page 9

    List of Figures 1.1. Packet Flow Schematic Part I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 1.2. Packet Flow Schematic Part II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • D-Link DFL-2560G - page 10

    List of Examples 1. Example Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.1. Enabling remote management via HTTPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • D-Link DFL-2560G - page 11

    4.13. if2 Configuration - Group Translation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 4.14. Setting up Transparent Mode for Scenario 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 4.15. Setting up Transp ...

  • D-Link DFL-2560G - page 12

    Preface Intended Audience The target audience for this reference guide is Administrators who are responsible for configuring and managing NetDefend Firewalls which are running the NetDefendOS operating system. This guide assumes that the reader has some basic knowledge of networks and network security. Text Structure and Conventions The text is bro ...

  • D-Link DFL-2560G - page 13

    items in the tree-view list at the left of the interface or in the menu bar or in a context menu need to be opened followed by information about the data items that need to be entered: 1. Go to Item X > Item Y > Item Z 2. Now enter: • DataItem1: datavalue1 • DataItem2: datavalue2 Highlighted Content Special sections of text which the read ...

  • D-Link DFL-2560G - page 14

    Chapter 1. NetDefendOS Overview This chapter outlines the key features of NetDefendOS. • Features, page 14 • NetDefendOS Architecture, page 17 • NetDefendOS State Engine Packet Flow, page 20 1.1. Features D-Link NetDefendOS is the base software engine that drives and controls the range of NetDefend Firewall hardware products. NetDefendOS as a ...

  • D-Link DFL-2560G - page 15

    VPN NetDefendOS supports a range of Virtual Private Network (VPN) solutions. NetDefendOS supports IPsec, L2TP and PPTP based VPNs concurrently, can act as either server or client for all of the VPN types, and can provide individual security policies for each VPN tunnel. The details for this can be found in Chapter 9, VPN which includes a summary of ...

  • D-Link DFL-2560G - page 16

    enables a device running NetDefendOS to distribute network load to multiple hosts. These features are discussed in detail in Chapter 10, Traffic Management . Note Threshold Rules are only available on certain D-Link NetDefend product models. Operations and Maintenance Adminstrator management of NetDefendOS is possible through either a Web-based Use ...

  • D-Link DFL-2560G - page 17

    1.2. NetDefendOS Architecture 1.2.1. State-based Architecture The NetDefendOS architecture is centered around the concept of state-based connections. Traditional IP routers or switches commonly inspect all packets and then perform forwarding decisions based on information found in the packet headers. With this approach, packets are forwarded withou ...

  • D-Link DFL-2560G - page 18

    NetDefendOS Rule Sets Finally, rules which are defined by the administrator in the various rule sets are used for actually implementing NetDefendOS security policies. The most fundamental set of rules are the IP Rules , which are used to define the layer 3 IP filtering policy as well as carrying out address translation and server load balancing. Th ...

  • D-Link DFL-2560G - page 19

    • TCP/UDP ports • ICMP types • Point in time in reference to a predefined schedule If a match cannot be found, the packet is dropped. If a rule is found that matches the new connection, the Action parameter of the rule decides what NetDefendOS should do with the connection. If the action is Drop, the packet is dropped and the event is logged ...

  • D-Link DFL-2560G - page 20

    1.3. NetDefendOS State Engine Packet Flow The diagrams in this section provide a summary of the flow of packets through the NetDefendOS state-engine. There are three diagrams, each flowing into the next. Figure 1.1. Packet Flow Schematic Part I The packet flow is continued on the following page. 1.3. NetDefendOS State Engine Packet Flow Chapter 1. ...

  • D-Link DFL-2560G - page 21

    Figure 1.2. Packet Flow Schematic Part II The packet flow is continued on the following page. 1.3. NetDefendOS State Engine Packet Flow Chapter 1. NetDefendOS Overview 21 ...

  • D-Link DFL-2560G - page 22

    Figure 1.3. Packet Flow Schematic Part III 1.3. NetDefendOS State Engine Packet Flow Chapter 1. NetDefendOS Overview 22 ...

  • D-Link DFL-2560G - page 23

    Apply Rules The figure below presents the detailed logic of the Apply Rules function in Figure 1.2, “Packet Flow Schematic Part II” above. Figure 1.4. Expanded Apply Rules Logic 1.3. NetDefendOS State Engine Packet Flow Chapter 1. NetDefendOS Overview 23 ...

  • D-Link DFL-2560G - page 24

    1.3. NetDefendOS State Engine Packet Flow Chapter 1. NetDefendOS Overview 24 ...

  • D-Link DFL-2560G - page 25

    Chapter 2. Management and Maintenance This chapter describes the management, operations and maintenance related aspects of NetDefendOS. • Managing NetDefendOS, page 25 • Events and Logging, page 51 • RADIUS Accounting, page 56 • Hardware Monitoring, page 61 • SNMP Monitoring, page 63 • The pcapdump Command, page 66 • Maintenance, page ...

  • D-Link DFL-2560G - page 26

    This feature is fully described in Section 2.1.6, “Secure Copy” . Console Boot Menu Before NetDefendOS starts running, a console connected directly to the NetDefend Firewall's RS232 port can be used to do basic configuration through the boot menu . This menu can be entered by pressing any console key between power-up and NetDefendOS starti ...

  • D-Link DFL-2560G - page 27

    NetDefendOS provides an intuitive Web Interface (WebUI) for management of the system via an Ethernet interface using a standard web browser. This allows the administrator to perform remote management from anywhere on a private network or the public Internet using a standard computer without having to install client software. Assignment of a Default ...

  • D-Link DFL-2560G - page 28

    password is admin and admin . If the user credentials are correct, you will be transferred to the main Web Interface page. First Time Web Interface Logon and the Setup Wizard When logging on for the first time, the default username is admin and the password is admin . After successful login, the WebUI user interface will be presented in the browser ...

  • D-Link DFL-2560G - page 29

    For information about the default user name and password, see Section 2.1.2, “The Default Administrator Account” . Note: Remote management access Access to the Web Interface is regulated by the configured remote management policy. By default, the system will only allow web access from the internal network. Interface Layout The main Web Interfac ...

  • D-Link DFL-2560G - page 30

    Controlling Access to the Web Interface By default, the Web Interface is accessible only from the internal network. If you need to enable access from other parts of the network, you can do so by modifying the remote management policy. Example 2.1. Enabling remote management via HTTPS CLI gw-world:/> add RemoteManagement RemoteMgmtHTTP https Netw ...

  • D-Link DFL-2560G - page 31

    is described below), or remotely via an Ethernet interface using the Secure Shell (SSH) protocol from an SSH client. The CLI provides a comprehensive set of commands that allow the display and modification of configuration data as well as allowing runtime data to be displayed and allowing system maintenance tasks to be performed. This section only ...

  • D-Link DFL-2560G - page 32

    command appears it can be re-executed in it's original form or changed first before execution. Tab Completion Remembering all the commands and their options can be difficult. NetDefendOS provides a feature called tab completion which means that pressing the tab key will cause automatically completion of the current part of the command. If comp ...

  • D-Link DFL-2560G - page 33

    Not all object types belong in a category. The object type UserAuthRule is a type without a category and will appear in the category list after pressing tab at the beginning of a command. The category is sometimes also referred to as a context . Selecting Object Categories With some categories, it is necessary to first choose a member of that categ ...

  • D-Link DFL-2560G - page 34

    can be done either by referring to it by its index, that is to say its list position, or by alternatively using the name assigned to it. The CLI Reference Guide lists the parameter options available for each NetDefendOS object, including the Name= and Index= options. Using Unique Names For convenience and clarity, it is recommended that a name is a ...

  • D-Link DFL-2560G - page 35

    4. Press the enter key on the terminal. The NetDefendOS login prompt should appear on the terminal screen. SSH (Secure Shell) CLI Access The SSH (Secure Shell) protocol can be used to access the CLI over the network from a remote host. SSH is a protocol primarily used for secure communication over insecure networks, providing strong authentication ...

  • D-Link DFL-2560G - page 36

    else as soon as possible after initial startup. User passwords can be any combination of characters and cannot be greater than 256 characters in length. It is recommended to use only printable characters. To change the password to, for example, my-password the following CLI commands are used. First we must change the current category to be the Loca ...

  • D-Link DFL-2560G - page 37

    Explicity Checking Configuration Integrity After changing a configuration on the NetDefend Firewall, and before the activate / commit commands, it is possible to explicitly check for any problems in a configuration using the command: gw-world:/> show -errors This will cause NetDefendOS to scan the configuration about to be activated and list any ...

  • D-Link DFL-2560G - page 38

    • Web Interface sessions connected by HTTP or HTTPS. The command without any options gives a summary of currently open sessions: gw-world:/> sessionmanager Session Manager status ---------------------- Active connections : 3 Maximum allowed connections : 64 Local idle session timeout : 900 NetCon idle session timeout : 600 To see a list of all ...

  • D-Link DFL-2560G - page 39

    Script Variables A script file can contain any number of script variables which are called: $1 , $2 , $3 , $4 ...... $n The values substituted for these variable names are specified as a list at the end of the script -execute command line. The number n in the variable name indicates the variable value's position in this list. $1 comes first, $ ...

  • D-Link DFL-2560G - page 40

    To move the example my_script.sgs to non-volatile memory the command would be: gw-world:/> script -store -name=my_script.sgs Alternatively, all scripts can be moved to non-volatile memory with the command: gw-world:/> script -store -all Listing Scripts The script on its own, command without any parameters, lists all the scripts currently avai ...

  • D-Link DFL-2560G - page 41

    then uploaded and executed on the other NetDefend Firewalls. The end result is that all units will have the same IP4Address objects in their address book. The name of the file created using the -create option cannot be greater than 16 characters in length (including the extension) and the filetype should be .sgs . Tip: Listing commands at the conso ...

  • D-Link DFL-2560G - page 42

    Download is done with the command: > scp <source_firewall> <local_filename> The source or destination NetDefend Firewall is of the form: <user_name>@<firewall_ip_address>:<filepath> . For example: admin@10.62.11.10:config.bak . The <user_name> must be a defined NetDefendOS user in the administrator user group. ...

  • D-Link DFL-2560G - page 43

    Scripts” . • sshclientkey/ - The SSH client key object type. Examples of Uploading and Downloading In some cases, a file is located in the NetDefendOS root. The license file ( license.lic ) falls into this category, as well as backup files for configurations ( config.bak ) and the complete system ( full.bak ). When uploading, these files contai ...

  • D-Link DFL-2560G - page 44

    If any console key is pressed during these 3 seconds then NetDefendOS startup pauses and the console boot menu is displayed. Initial Boot Menu Options without a Password Set When NetDefendOS is started for the first time with no console password set for console access then the full set of boot menu options are displayed as shown below: The options ...

  • D-Link DFL-2560G - page 45

    The 1. Start firewall option re-continues the interrupted NetDefendOS startup process. If the 2. Login option is chosen, the console password must be entered and the full boot menu described above is entered. Removing the Console Password Once the console password is set it can be removed by selecting the Set console password option in the boot men ...

  • D-Link DFL-2560G - page 46

    Default: 443 HTTPS Certificate Specifies which certificate to use for HTTPS traffic. Only RSA certificates are supported. Default: HTTPS 2.1.9. Working with Configurations Configuration Objects The system configuration is built up by Configuration Objects , where each object represents a configurable item of any kind. Examples of configuration obje ...

  • D-Link DFL-2560G - page 47

    can be added to the list. • Header - The header row displays the titles of the columns in the list. The tiny arrow images next to each title can be used for sorting the list according to that column. • Rows - Each row in the list corresponds to one configuration item. Most commonly, each row starts with the name of the object (if the item has a ...

  • D-Link DFL-2560G - page 48

    Show the object again to verify the new property value: gw-world:/> show Service ServiceTCPUDP telnet Property Value ----------------- ------- Name: telnet DestinationPorts: 23 Type: TCP SourcePorts: 0-65535 SYNRelay: No PassICMPReturn: No ALG: (none) MaxSessions: 1000 Comments: Modified Comment Web Interface 1. Go to Objects > Services 2. Cl ...

  • D-Link DFL-2560G - page 49

    6. Click OK 7. Verify that the new IP4 address object has been added to the list Example 2.7. Deleting a Configuration Object This example shows how to delete the newly added IP4Address object. CLI gw-world:/> delete Address IP4Address myhost Web Interface 1. Go to Objects > Address Book 2. Right-click on the row containing the myhost object ...

  • D-Link DFL-2560G - page 50

    * ServiceTCPUDP telnet A "+" character in front of the row indicates that the object has been added. A "*" character indicates that the object has been modified. A "-" character indicates that the object has been marked for deletion. Web Interface 1. Go to Configuration > View Changes in the menu bar A list of chang ...

  • D-Link DFL-2560G - page 51

    2.2. Events and Logging 2.2.1. Overview The ability to log and analyze system activities is an essential feature of NetDefendOS. Logging enables not only monitoring of system status and health, but also allows auditing of network usage and assists in trouble-shooting. Log Message Generation NetDefendOS defines a large number of different log event ...

  • D-Link DFL-2560G - page 52

    By default all messages of level Info and above are sent. The Debug category of designed for troubleshooting only and should only be turned on if required to try and solve a problem. Messages of all severity levels are found listed in the NetDefendOS Log Reference Guide . 2.2.3. Log Message Distribution To distribute and log the event messages gene ...

  • D-Link DFL-2560G - page 53

    In order to facilitate automated processing of all messages, NetDefendOS writes all log data to a single line of text. All data following the initial text is presented in the format name=value . This enables automatic filters to easily find the values they are looking for without assuming that a specific piece of data is in a specific location in t ...

  • D-Link DFL-2560G - page 54

    by D-Link and defines the SNMP objects and data types that are used to describe an SNMP Trap received from NetDefendOS. Note There is a different MIB file for each model of NetDefend Firewall. Make sure that the correct file is used. For each NetDefend Firewall model there is one generic trap object called DLNNNosGenericTrap , that is used for all ...

  • D-Link DFL-2560G - page 55

    Send Limit This setting limits how many log packets NetDefendOS may send out per second. This value should never be set too low, as this may result in important events not being logged, nor should it be set too high. A situation where setting too high a value may cause damage is when NetDefendOS sends a log message to a server whose log receiver is ...

  • D-Link DFL-2560G - page 56

    2.3. RADIUS Accounting 2.3.1. Overview Within a network environment containing large numbers of users, it is advantageous to have one or a cluster of central servers that maintain user account information and are responsible for authentication and authorization tasks. The central database residing on the dedicated server(s) contains all user creden ...

  • D-Link DFL-2560G - page 57

    authentication server. • How Authenticated - How the user was authenticated. This is set to either RADIUS if the user was authenticated via RADIUS, or LOCAL if the user was authenticated via a local user database. • Delay Time - The time delay (in seconds) since the AccountingRequest packet was sent and the authentication acknowledgement was re ...

  • D-Link DFL-2560G - page 58

    Tip: The meaning of an asterisk in the list The asterisk "*" symbol in the above list indicates that the sending of the parameter is user configurable. 2.3.3. Interim Accounting Messages In addition to START and STOP messages NetDefendOS can optionally periodically send Interim Accounting Messages to update the accounting server with the ...

  • D-Link DFL-2560G - page 59

    Firewalls. This means that accounting information is automatically updated on both cluster members whenever a connection is closed. Two special accounting events are also used by the active unit to keep the passive unit synchronized: • An AccountingStart event is sent to the inactive member in an HA setup whenever a response has been received fro ...

  • D-Link DFL-2560G - page 60

    continue to be logged in. Disabling the setting will mean that the user will be logged out if the RADIUS accounting server cannot be reached even though the user has been previously authenticated. Default: Enabled Logout at shutdown If there is an orderly shutdown of the NetDefend Firewall by the administrator, then NetDefendOS will delay the shutd ...

  • D-Link DFL-2560G - page 61

    2.4. Hardware Monitoring Availability Certain D-Link hardware models allow the administrator to use the CLI to query the current value of various hardware operational parameters such as the current temperature inside the firewall. This feature is referred to as Hardware Monitoring . The D-Link NetDefend models that currently support hardware monito ...

  • D-Link DFL-2560G - page 62

    The -verbose option displays the current values plus the configured ranges: gw-world:/> hwm -a -v 2 sensors available Poll interval time = 500ms Name [type][number] = low_limit] current_value [high_limit (unit) ----------------------------------------------------------------- SYS Temp [TEMP ][ 0] = 44.000] 45.000 [ 0.000 (C) CPU Temp [TEMP ][ 1] ...

  • D-Link DFL-2560G - page 63

    2.5. SNMP Monitoring Overview Simple Network Management Protocol (SNMP) is a standardized protocol for management of network devices. An SNMP compliant client can connect to a network device which supports the SNMP protocol to query and control it. NetDefendOS supports SNMP version 1 and version 2. Connection can be made by any SNMP compliant clien ...

  • D-Link DFL-2560G - page 64

    SNMP access. Port 161 is usually used for SNMP and NetDefendOS always expects SNMP traffic on that port. Remote Access Encryption It should be noted that SNMP Version 1 or 2c access means that the community string will be sent as plain text over a network. This is clearly insecure if a remote client is communicating over the public Internet. It is ...

  • D-Link DFL-2560G - page 65

    Default: Enabled SNMP Request Limit Maximum number of SNMP requests that will be processed each second by NetDefendOS. Should SNMP requests exceed this rate then the excess requests will be ignored by NetDefendOS. Default: 100 System Contact The contact person for the managed node. Default: N/A System Name The name for the managed node. Default: N/ ...

  • D-Link DFL-2560G - page 66

    2.6. The pcapdump Command A valuable diagnostic tool is the ability to examine the packets that enter and leave the interfaces of a NetDefend Firewall. For this purpose, NetDefendOS provides the CLI command pcapdump which not only allows the examination of packet streams entering and leaving interfaces but also allows the filtering of these streams ...

  • D-Link DFL-2560G - page 67

    It is possible to have multiple pcapdump executions being performed at the same time. The following points describe this feature: 1. All capture from all executions goes to the same memory buffer. The command can be launched multiple times with different interfaces specified. In this case the packet flow for the different executions will be grouped ...

  • D-Link DFL-2560G - page 68

    • The filename and extension can only contain the characters A-Z, 0-9, "-" and "_". Combining Filters It is possible to use several of these filter expressions together in order to further refine the packets that are of interest. For example we might want to examine the packets going to a particular destination port at a parti ...

  • D-Link DFL-2560G - page 69

    2.7. Maintenance 2.7.1. Auto-Update Mechanism A number of the NetDefendOS security features rely on external servers for automatic updates and content filtering. The Intrusion Prevention and Detection system and Anti-Virus modules require access to updated signature databases in order to provide protection against the latest threats. To facilitate ...

  • D-Link DFL-2560G - page 70

    be altered to include the date. For example, full.bak might become full-20081121.bak to show it is a snapshot of the state on November 21st, 2008. To restore a backup file, the administrator should upload the file to the NetDefend Firewall. The name of the file does not need to be changed in any way and can retain the date since NetDefendOS will re ...

  • D-Link DFL-2560G - page 71

    Important: Any upgrades will be lost after a factory reset It should be understood that a reset to factory defaults is exactly that. Any NetDefendOS upgrades performed since the unit left the factory will be lost. Reset Procedure for the NetDefend DFL-210, 260, 800 and 860 To reset the NetDefend DFL-210/260/800/860 models, hold down the reset butto ...

  • D-Link DFL-2560G - page 72

    2.7.3. Restore to Factory Defaults Chapter 2. Management and Maintenance 72 ...

  • D-Link DFL-2560G - page 73

    Chapter 3. Fundamentals This chapter describes the fundamental logical objects which make up a NetDefendOS configuration. These objects include such items as IP addresses and IP rules. Some exist by default and some must be defined by the administrator. In addition, the chapter explains the different interface types and explains how security polici ...

  • D-Link DFL-2560G - page 74

    corresponds to a 32 address net (netmask 255.255.255.224 ) and so on. The numbers 0-32 correspond to the number of binary ones in the netmask. For example: 192.168.0.0/24 . IP Range A range of IP addresses is represented on the form a.b.c.d - e.f.g.h . Note that ranges are not limited to netmask boundaries. They may include any span of IP addresses ...

  • D-Link DFL-2560G - page 75

    Web Interface 1. Go to Objects > Address Book > Add > IP address 2. Specify a suitable name for the IP Range, for example wwwservers . 3. Enter 192.168.10.16-192.168.10.21 as the IP Address 4. Click OK Example 3.4. Deleting an Address Object To delete an object named wwwsrv1 in the Address Book, do the following: CLI gw-world:/> delete ...

  • D-Link DFL-2560G - page 76

    Web Interface 1. Go to Objects > Address Book > Add > Ethernet Address 2. Specify a suitable name for the Ethernet Address object, for example wwwsrv1_mac 3. Enter 08-a3-67-bc-2e-f2 as the MAC Address 4. Click OK 3.1.4. Address Groups Groups Simplify Configuration Address objects can be grouped in order to simplify configuration. Consider ...

  • D-Link DFL-2560G - page 77

    Otherwise, the object will be left empty (in other words, the IP address will be 0.0.0.0/0 ). all-nets The all-nets IP address object is initialized to the IP address 0.0.0.0/0 , which represents all possible IP addresses. The all-nets IP object is used extensively in the configuration of NetDefendOS and it is important to understand its significan ...

  • D-Link DFL-2560G - page 78

    3.2. Services 3.2.1. Overview A Service object is a reference to a specific IP protocol with associated parameters. A Service definition is usually based on one of the major transport protocols such as TCP or UDP, with the associated port number(s). The HTTP service, for instance, is defined as using the TCP protocol with associated port 80. Howeve ...

  • D-Link DFL-2560G - page 79

    To view a specific service in the system: CLI gw-world:/> show Service ServiceTCPUDP echo The output will look similar to the following listing: Property Value ----------------- ---------------- Name: echo DestinationPorts: 7 Type: TCPUDP (TCP/UDP) SourcePorts: 0-65535 PassICMPReturn: No ALG: (none) MaxSessions: 1000 Comments: Echo service Web I ...

  • D-Link DFL-2560G - page 80

    Port Ranges Some services use a range of destination ports. As an example, the NetBIOS protocol used by Microsoft Windows uses destination ports 137 to 139 . To define a range of ports in a TCP/UDP service object, the format mmm-nnn is used. A port range is inclusive, meaning that a range specified as 137-139 covers ports 137 , 138 and 139 . Multip ...

  • D-Link DFL-2560G - page 81

    Gateway (ALG) to enable deeper inspection of certain protocols. For more information see Section 6.2, “ALGs” . Max Sessions An important parameter associated with a Service is Max Sessions . This parameter is allocated a default value when the Service is associated with an ALG. The default value varies according to the ALG it is associated with ...

  • D-Link DFL-2560G - page 82

    • Code 4: Cannot Fragment • Code 5: Source Route Failed • Redirect: the source is told that there is a better route for a particular packet. Codes assigned are as follows: • Code 0: Redirect datagrams for the network • Code 1: Redirect datagrams for the host • Code 2: Redirect datagrams for the Type of Service and the network • Code 3 ...

  • D-Link DFL-2560G - page 83

    4. Optionally enter Virtual Router Redundancy Protocol in the Comments control 5. Click OK 3.2.5. Service Groups A Service Group is, exactly as the name suggests, a NetDefendOS object that consists of a collection of services. Although the group concept is simple, it can be very useful when constructing security policies. For example, there may be ...

  • D-Link DFL-2560G - page 84

    3.3. Interfaces 3.3.1. Overview An Interface is one of the most important logical building blocks in NetDefendOS. All network traffic that passes through or gets terminated in the system is done so through one or several interfaces. An interface can be seen as a doorway for network traffic to or from the system. Thus, when traffic enters the system ...

  • D-Link DFL-2560G - page 85

    found in Section 9.5, “PPTP/L2TP” . • GRE interfaces are used to establish GRE tunnels. More information about this topic can be found in Section 3.3.5, “GRE Tunnels” . Even though the various types of interfaces are very different in the way they are implemented and how they work, NetDefendOS treats all interfaces as logical IP interface ...

  • D-Link DFL-2560G - page 86

    progressively smaller as the transmission rates get faster from normal Ethernet to Fast Ethernet and then Gigabit Ethernet. Each NetDefendOS Ethernet interface corresponds to a physical Ethernet port in the system. The number of ports, their link speed and the way the ports are realized, is dependent on the hardware model. Note: Additional switch p ...

  • D-Link DFL-2560G - page 87

    • Instead, the ip_lan object in the NetDefendOS Address Book should be assigned the new address since it is this object that is used by many other NetDefendOS objects such as IP rules. The CLI command to do this would be: gw-world:/> set Address IP4Address ip_lan Address=10.1.1.2 This same operation could also be done through the Web Interface ...

  • D-Link DFL-2560G - page 88

    Web Interface 1. Go to Interfaces > Ethernet 2. Select the Ethernet interface of interest 3. Enable the Enable DHCP client option 4. Click OK 3.3.2.1. Useful CLI Commands for Ethernet Interfaces This section summarizes the CLI commands most commonly used for examining and manipulating NetDefendOS Ethernet interfaces. Ethernet interfaces can also ...

  • D-Link DFL-2560G - page 89

    Here, tab completion is used again at the end of the command line: gw-world:/> set Address IP4Address <tab> [<Category>] <Type> [<Identifier>]: dnsserver1_ip InterfaceAddresses/wan_br timesyncsrv1_ip InterfaceAddresses/aux_ip InterfaceAddresses/wan_dns1 InterfaceAddresses/aux_net InterfaceAddresses/wan_dns2 InterfaceAddre ...

  • D-Link DFL-2560G - page 90

    For a complete list of all CLI options see the CLI Reference Guide . 3.3.3. VLAN Overview Virtual LAN (VLAN) support in NetDefendOS allows the definition of one or more Virtual LAN interfaces which are associated with a particular physical interface. These are then considered to be logical interfaces by NetDefendOS and can be treated like any other ...

  • D-Link DFL-2560G - page 91

    With NetDefendOS VLANs, the physical connections are as follows: • One of more VLANs are configured on a physical NetDefend Firewall interface and this is connected directly to a switch. This link acts as a VLAN trunk . The switch used must support port based VLANs . This means that each port on the switch can be configured with the ID of the VLA ...

  • D-Link DFL-2560G - page 92

    The number of VLAN interfaces that can be defined for a NetDefendOS installation is limited by the parameters of the license used. Different hardware models have different licenses and different limits on VLANs. Summary of VLAN Setup It is important to understand that the administrator should treat a VLAN interface just like a physical interface in ...

  • D-Link DFL-2560G - page 93

    3.3.4. PPPoE 3.3.4.1. Overview Point-to-Point Protocol over Ethernet (PPPoE) is a tunneling protocol used for connecting multiple users on an Ethernet network to the Internet through a common serial interface, such as a single DSL line, wireless device or cable modem. All the users on the Ethernet share a common connection, while access control can ...

  • D-Link DFL-2560G - page 94

    receives this IP address information from the ISP, it stores it in a network object and uses it as the IP address of the interface. User authentication If user authentication is required by the ISP, the username and password can be setup in NetDefendOS for automatic sending to the PPPoE server. Dial-on-demand If dial-on-demand is enabled, the PPPoE ...

  • D-Link DFL-2560G - page 95

    • Service Name: Service name provided by the service provider • Username: Username provided by the service provider • Password: Password provided by the service provider • Confirm Password: Retype the password • Under Authentication specify which authentication protocol to use (the default settings will be used if not specified) • Disab ...

  • D-Link DFL-2560G - page 96

    Like other tunnels in NetDefendOS such as an IPsec tunnel, a GRE Tunnel is treated as a logical interface by NetDefendOS, with the same filtering, traffic shaping and configuration capabilities as a standard interface. The GRE options are: • IP Address - This is the IP address of the sending interface. This is optional and can be left blank. If i ...

  • D-Link DFL-2560G - page 97

    The diagram above shows a typical GRE scenario, where two NetDefend Firewalls A and B must communicate with each other through the intervening internal network 172.16.0.0/16 . Any traffic passing between A and B is tunneled through the intervening network using a GRE tunnel and since the network is internal and not public there is no need for encry ...

  • D-Link DFL-2560G - page 98

    • Remote Endpoint: remote_gw • Use Session Key: 1 • Additional Encapulation Checksum: Enabled 3. Define a route in the main routing table which routes all traffic to remote_net_A on the GRE_to_A GRE interface. This is not necessary if the option Add route for remote network is enabled in the Advanced tab, since this will add the route automat ...

  • D-Link DFL-2560G - page 99

    3.4. ARP 3.4.1. Overview Address Resolution Protocol (ARP) is a protocol, which maps a network layer protocol address to a data link layer hardware address and it is used to resolve an IP address into its corresponding Ethernet address. ARP operates at the OSI Data Link Layer (Layer 2 - see Appendix D, The OSI Framework ) and is encapsulated by Eth ...

  • D-Link DFL-2560G - page 100

    The default expiration time for dynamic ARP entries is 900 seconds (15 minutes). This can be changed by modifying the advanced setting ARP Expire . The setting ARP Expire Unknown specifies how long NetDefendOS will remember addresses that cannot be reached. This is done to ensure that NetDefendOS does not continuously request such addresses. The de ...

  • D-Link DFL-2560G - page 101

    hash size for VLAN interfaces only. The default value is 64 . 3.4.4. Static and Published ARP Entries NetDefendOS supports defining static ARP entries (static binding of IP addresses to Ethernet addresses) as well as publishing IP addresses with a specific Ethernet address. Static ARP Entries Static ARP items may help in situations where a device i ...

  • D-Link DFL-2560G - page 102

    the corresponding NetDefendOS interface. Another use is publishing multiple addresses on an external interface, enabling NetDefendOS to statically address translate communications to these addresses and send it onwards to internal servers with private IP addresses. There are two publishing modes; Publish and XPublish. The difference between the two ...

  • D-Link DFL-2560G - page 103

    Allowing this to take place may allow hijacking of local connections. However, not allowing this may cause problems if, for example, a network adapter is replaced, as NetDefendOS will not accept the new address until the previous ARP cache entry has timed out. The advanced setting ARP Changes can be changed to modify this behavior. The default beha ...

  • D-Link DFL-2560G - page 104

    Default: DropLog ARP Requests Determines if NetDefendOS will automatically add the data in ARP requests to its ARP table. The ARP specification states that this should be done, but as this procedure can facilitate hijacking of local connections, it is not normally allowed. Even if ARPRequests is set to "Drop", meaning that the packet is d ...

  • D-Link DFL-2560G - page 105

    broadcast addresses. Such claims are usually never correct. Default: DropLog ARP cache size How many ARP entries there can be in the cache in total. Default: 4096 ARP Hash Size Hashing is used to rapidly look up entries in a table. For maximum efficiency, the hash size should be twice as large as the table it is indexing. If the largest directly-co ...

  • D-Link DFL-2560G - page 106

    3.5. The IP Rule Set 3.5.1. Security Policies Common Policy Characteristics NetDefendOS Security Policies designed by the administrator, regulate the way in which traffic can flow through the NetDefend Firewall. Policies in NetDefendOS are defined by different NetDefendOS rule sets . These rule sets share a common means of specifying filtering crit ...

  • D-Link DFL-2560G - page 107

    and are described in Chapter 8, User Authentication . Specifying Any Interface or Network When specifying the filtering criteria in any of the rule sets specified above there are three useful predefined options that can be used: • For a Source or Destination Network, the all-nets option is equivalent to the IP address 0.0.0.0/0 which will mean th ...

  • D-Link DFL-2560G - page 108

    If the IP rule used is an Allow rule then this is bi-directional by default. The ordering of these steps is important. The route lookup occurs first to determine the exiting interface and then NetDefendOS looks for an IP rule that allows the traffic to leave on that interface. If a rule doesn't exist then the traffic is dropped. Figure 3.2. Si ...

  • D-Link DFL-2560G - page 109

    Stateful Inspection After initial rule evaluation of the opening connection, subsequent packets belonging to that connection will not need to be evaluated individually against the rule set. Instead, a highly efficient algorithm searches the state table for each packet to determine if it belongs to an established connection. This approach is known a ...

  • D-Link DFL-2560G - page 110

    SAT This tells NetDefendOS to perform static address translation. A SAT rule always requires a matching Allow , NAT or FwdFast IP rule further down the rule set (see Section 7.3, “SAT” in Chapter 7, Address Translation for a detailed description). Drop This tells NetDefendOS to immediately discard the packet. This is an "impolite" ver ...

  • D-Link DFL-2560G - page 111

    name and can then be used to contain all the IP rules that are related together as a group. Using folders is simply a way for the administrator to conveniently divide up IP rule set entries and no special properties are given to entries in different folders. NetDefendOS continues to see all entries as though they were in a single set of IP rules. T ...

  • D-Link DFL-2560G - page 112

    3.6. Schedules In some scenarios, it might be useful to control not only what functionality is enabled, but also when that functionality is being used. For instance, the IT policy of an enterprise might stipulate that web traffic from a certain department is only allowed access outside that department during normal office hours. Another example mig ...

  • D-Link DFL-2560G - page 113

    Return to the top level: gw-world:/main> cc Configuration changes must be saved by then issuing an activate followed by a commit command. Web Interface 1. Go to Objects > Schedules > Add > Schedule 2. Enter the following: • Name: OfficeHours 3. Select 08-17, Monday to Friday in the grid 4. Click OK 1. Go to Rules > IP Rules > Ad ...

  • D-Link DFL-2560G - page 114

    3.7. Certificates 3.7.1. Overview X.509 NetDefendOS supports digital certificates that comply with the ITU-T X.509 standard. This involves the use of an X.509 certificate hierarchy with public-key cryptography to accomplish key distribution and entity authentication. References in this manual to a certificate means a X.509 certificate . A certifica ...

  • D-Link DFL-2560G - page 115

    Validity Time A certificate is not valid forever. Each certificate contains the dates between which the certificate is valid. When this validity period expires, the certificate can no longer be used, and a new certificate has to be issued. Important Make sure the NetDefendOS date and time are set correctly when using certificates. Certificate Revoc ...

  • D-Link DFL-2560G - page 116

    There are two types of certificates that can be uploaded: self-signed certificates and remote certificates belonging to a remote peer or CA server. Self-signed certificates can be generated by using one of a number of freely available utilities for doing this. Example 3.19. Uploading a Certificate The certificate may either be self-signed or belong ...

  • D-Link DFL-2560G - page 117

    • Take out the relevant parts of the .pem file to form the required .cer and .key files. The detailed steps for the above stages are as follows: 1. Create the gateway certificate on the Windows CA server and export it to a .pfx file on the local NetDefendOS management workstation disk. 2. Now convert the local .pfx file to a .pem file. This can b ...

  • D-Link DFL-2560G - page 118

    3.8. Date and Time 3.8.1. Overview Correctly setting the date and time is important for NetDefendOS to operate properly. Time scheduled policies, auto-update of the IDP and Anti-Virus databases, and other product features require that the system clock is accurately set. In addition, log messages are tagged with time-stamps in order to indicate when ...

  • D-Link DFL-2560G - page 119

    counted as being inside a given time zone will then have the same local time and this will be one of the integer offsets from GMT. The NetDefendOS time zone setting reflects the time zone where the NetDefend Firewall is physically located. Example 3.22. Setting the Time Zone To modify the NetDefendOS time zone to be GMT plus 1 hour, follow the step ...

  • D-Link DFL-2560G - page 120

    NetDefendOS is able to adjust the clock automatically based on information received from one or more Time Servers which provide a highly accurate time, usually using atomic clocks. Using Time Servers is highly recommended as it ensures NetDefendOS will have its date and time aligned with other network devices. Time Synchronization Protocols Time Sy ...

  • D-Link DFL-2560G - page 121

    The time server URLs must have the prefix dns: to specify that they should be resolved with a DNS server. NetDefendOS must therefore also have a DNS server defined so this resolution can be performed. Note If the TimeSyncInterval parameter is not specified when using the CLI to set the synchronization interval, the default of 86400 seconds (= 1 day ...

  • D-Link DFL-2560G - page 122

    Example 3.27. Forcing Time Synchronization This example demonstrates how to force time synchronization, overiding the maximum adjustment setting. CLI gw-world:/> time -sync -force Synchronization Intervals The interval between each synchronization attempt can be adjusted if needed. By default, this value is 86,400 seconds (1 day), meaning that t ...

  • D-Link DFL-2560G - page 123

    DST Offset Daylight saving time offset in minutes. Default: 0 DST Start Date What month and day DST starts, in the format MM-DD. Default: none DST End Date What month and day DST ends, in the format MM-DD. Default: none Time Sync Server Type Type of server for time synchronization, UDPTime or SNTP (Simple Network Time Protocol). Default: SNTP Prima ...

  • D-Link DFL-2560G - page 124

    Group interval Interval according to which server responses will be grouped. Default: 10 3.8.4. Settings Summary for Date and Time Chapter 3. Fundamentals 124 ...

  • D-Link DFL-2560G - page 125

    3.9. DNS Overview A DNS server can resolve a Fully Qualified Domain Name (FQDN) into the corresponding numeric IP address. FQDNs are unambiguous textual domain names which specify a node's unique position in the Internet's DNS tree hierarchy. FQDN resolution allows the actual physical IP address to change while the FQDN can stay the same. ...

  • D-Link DFL-2560G - page 126

    Dynamic DNS A DNS feature offered by NetDefendOS is the ability to explicitly inform DNS servers when the external IP address of the NetDefend Firewall has changed. This is sometimes referred to as Dynamic DNS and is useful where the NetDefend Firewall has an external IP address that can change. Dynamic DNS can also be useful in VPN scenarios where ...

  • D-Link DFL-2560G - page 127

    3.9. DNS Chapter 3. Fundamentals 127 ...

  • D-Link DFL-2560G - page 128

    Chapter 4. Routing This chapter describes how to configure IP routing in NetDefendOS. • Overview, page 128 • Static Routing, page 129 • Policy-based Routing, page 143 • Route Load Balancing, page 148 • Dynamic Routing, page 154 • Multicast Routing, page 162 • Transparent Mode, page 174 4.1. Overview IP routing is one of the most funda ...

  • D-Link DFL-2560G - page 129

    4.2. Static Routing The most basic form of routing is known as Static Routing . The word " static " refers to the fact that entries in the routing table are manually added and are therefore permanent (or static) by nature. Due to this manual approach, static routing is most appropriate to use in smaller network deployments where addresses ...

  • D-Link DFL-2560G - page 130

    This parameter usually doesn't need to be specified. If it is specified, NetDefendOS responds to ARP queries sent to this address. A special section below explains this parameter in more depth. Local IP Address and Gateway are mutually exclusive and either one or the other should be specified. • Metric This is a metric value assigned to the ...

  • D-Link DFL-2560G - page 131

    The above routing table provides the following information: • Route #1 All packets going to hosts on the 192.168.0.0/24 network should be sent out on the lan interface. As no gateway is specified for the route entry, the host is assumed to be located on the network segment directly reachable from the lan interface. • Route #2 All packets going ...

  • D-Link DFL-2560G - page 132

    • Local IP Address: An address within the second network's IP range. When the Default Gateway of the second network's clients is now set to the same value as the Local IP Address of the above route, the clients will be able to communicate successfully with the interface. The IP address chosen in the second network isn't significant ...

  • D-Link DFL-2560G - page 133

    network of a connection but also for the source network. The route that defines the source network simply says that the source network is found on a particular interface. When a new connection is opened, NetDefendOS performs a check known as a reverse route lookup which looks for this route. The source network route is not used to perform routing b ...

  • D-Link DFL-2560G - page 134

    0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.10 20 10.0.0.0 255.0.0.0 10.4.2.143 10.4.2.143 1 10.4.2.143 255.255.255.255 127.0.0.1 127.0.0.1 50 10.255.255.255 255.255.255.255 10.4.2.143 10.4.2.143 50 85.11.194.33 255.255.255.255 192.168.0.1 192.168.0.10 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.0.0 255.255.255.0 192.168.0.10 192.168.0.10 20 192 ...

  • D-Link DFL-2560G - page 135

    gw-world:/main> show Route # Interface Network Gateway Local IP - --------- -------- ------------- -------- 1 wan all-nets 213.124.165.1 (none) 2 lan lannet (none) (none) 3 wan wannet (none) (none) To see the active routing table enter: gw-world:/> routes Flags Network Iface Gateway Local IP Metric ----- ------------------ -------------- ---- ...

  • D-Link DFL-2560G - page 136

    However, the option also exists for any physical interface to indicate that it should be used for connection to the Internet. In the Web Interface this is an advanced setting in the Ethernet interface properties called: Automatically add a default route for this interface using the given default gateway . When this option is selected, the appropria ...

  • D-Link DFL-2560G - page 137

    Tip: Understanding output from the routes command For detailed information about the output of the CLI routes command. Please see the CLI Reference Guide. 4.2.3. Route Failover Overview NetDefend Firewalls are often deployed in mission-critical locations where availability and connectivity is crucial. A corporation relying heavily on access to the ...

  • D-Link DFL-2560G - page 138

    instantly noticed, this method provides the fastest response to failure. Gateway Monitoring If a specific gateway has been specified as the next hop for a route, accessibility to that gateway can be monitored by sending periodic ARP requests. As long as the gateway responds to these requests, the route is considered to be functioning correctly. Set ...

  • D-Link DFL-2560G - page 139

    Route Interface Grouping When using route monitoring, it is important to check if a failover to another route will cause the routing interface to be changed. If this could happen, it is necessary to take some precautionary steps to ensure that policies and existing connections will be maintained. To illustrate the problem, consider the following co ...

  • D-Link DFL-2560G - page 140

    The advantages of Host Monitoring are twofold: • In a complex network topology it is more reliable to check accessibility to external hosts. Just monitoring a link to a local switch may not indicate a problem in another part of the internal network. • Host monitoring can be used to help in setting the acceptable Quality of Service level of Inte ...

  • D-Link DFL-2560G - page 141

    • Sample The number of polling attempts used as a sample size for calculating the Percentage Loss and the Average Latency . This value cannot be less than 1. • Maximum Failed Poll Attempts The maximum permissible number of polling attempts that fail. If this number is exceeded then the host is considered unreachable. • Max Average Latency The ...

  • D-Link DFL-2560G - page 142

    Overview As discussed previously in Section 3.4, “ARP” , the ARP protocol facilitates a mapping between an IP address and the MAC address of a node on an Ethernet network. However, situations may exist where a network running Ethernet is separated into two parts with a routing device such as an installed NetDefend Firewall, in between. In such ...

  • D-Link DFL-2560G - page 143

    4.3. Policy-based Routing 4.3.1. Overview Policy-based Routing (PBR) is an extension to the standard routing described previously. It offers administrators significant flexibility in implementing routing decision policies by being able to define rules so alternative routing tables are used. Normal routing forwards packets according to destination I ...

  • D-Link DFL-2560G - page 144

    When looking up Policy-based Rules, it is the first matching rule found that is triggered. 4.3.4. PBR Table Selection When a packet corresponding to a new connection first arrives, the processing steps are as follows to determine which routing table is chosen: 1. The PBR Rules must first be looked up but to do this the packet's destination int ...

  • D-Link DFL-2560G - page 145

    Important: Ensure all-nets appears in the main table A common mistake with policy-based routing is the absence of the default route with a destination interface of all-nets in the default main routing table. If there is no route that is an exact match then the absence of a default all-nets route will mean that the connection will be dropped. Exampl ...

  • D-Link DFL-2560G - page 146

    This example illustrates a multiple ISP scenario which is a common use of Policy-based Routing. The following is assumed: • Each ISP will give you an IP network from its network range. We will assume a 2-ISP scenario, with the network 10.10.10.0/24 belonging to ISP A and 20.20.20.0/24 belonging to ISP B. The ISP gateways are 10.10.10.1 and 20.20. ...

  • D-Link DFL-2560G - page 147

    Note Rules in the above example are added for both inbound and outbound connections. 4.3.5. The Ordering parameter Chapter 4. Routing 147 ...

  • D-Link DFL-2560G - page 148

    4.4. Route Load Balancing Overview NetDefendOS provides the option to perform Route Load Balancing (RLB). This is the ability to distribute traffic over multiple alternate routes based on a number of predefined distribution algorithms. The purpose of this feature is to provide the following: • Balancing of traffic between interfaces in a policy d ...

  • D-Link DFL-2560G - page 149

    3. If more than one matching route is found then RLB is used to choose which one to use. This is done according to which algorithm is selected in the table's RLB Instance object: • Round Robin Successive routes are chosen from the matching routes in a "round robin" fashion provided that the metric of the routes is the same. This re ...

  • D-Link DFL-2560G - page 150

    Spillover Limits are set separately for ingoing and outgoing traffic with only one of these typically being specified. If both are specified then only one of them needs to be exceeded continuously for Hold Timer seconds for the next matching route to be chosen. The units of the limits, such as Mbps, can be selected to simplify specification of the ...

  • D-Link DFL-2560G - page 151

    Several alternative routes can be set up, each with their own interface limits and each with a different metric. The route with the lowest metric is chosen first and when that route's interface limits are exceeded, the route with the next highest metric is then chosen. When that new route's interface limits are also exceeded then the rout ...

  • D-Link DFL-2560G - page 152

    to the firewall interfaces WAN1 and WAN2 . RLB will be used to balance the connections between the two ISPs. Figure 4.5. A Route Load Balancing Scenario We first need to define two routes to these two ISPs in the main routing table as shown below: Route No. Interface Destination Gateway Metric 1 WAN1 all-nets GW1 100 2 WAN2 all-nets GW2 100 We will ...

  • D-Link DFL-2560G - page 153

    achieve stickiness so the server always sees the same source IP address ( WAN1 or WAN2 ) from a single client. CLI gw-world:/> add RouteBalancingInstance main Algorithm=Destination Web Interface 1. Go to Routing > Route Load Balancing > Instances > Add > Route Balancing Instance 2. The route balancing instance dialog will appear. Now ...

  • D-Link DFL-2560G - page 154

    4.5. Dynamic Routing 4.5.1. Dynamic Routing overview Dynamic routing is different to static routing in that the NetDefend Firewall will adapt to changes of network topology or traffic load automatically. NetDefendOS first learns of all the directly connected networks and gets further route information from other routers. Detected routes are sorted ...

  • D-Link DFL-2560G - page 155

    OSPF is not available on the DFL-210 and 260. Comparing Dynamic Routing Algorithms Due to the fact that the global link state information is maintained everywhere in a network, LS algorithms offer a high degree of configuration control and scalability. Changes result in broadcasts of just the updated information to other routers which means faster ...

  • D-Link DFL-2560G - page 156

    Link-state Routing OSPF is a form of link-state routing protocol that defines the sending of link-state advertisements (LSAs) to all other routers within the same area. Each router maintains a database, known as a link-state database , describing the AS topology. From the information in this database, each router constructs a tree of shortest paths ...

  • D-Link DFL-2560G - page 157

    Neighbors Routers that are in the same area become neighbors in that area. Neighbors are elected via the Hello protocol. Hello packets are sent periodically out of each interface using IP multicast. Routers become neighbors as soon as they see themselves listed in the neighbor's Hello packet. This way, a two way communication is guaranteed. Th ...

  • D-Link DFL-2560G - page 158

    In the above example, the Virtual Link is configured between fw1 and fw2 on Area 1, as it is used as the transit area. In this configuration only the Router ID has to be configured. The diagram shows that fw2 needs to have a Virtual Link to fw1 with Router ID 192.168.1.1 and vice versa. These Virtual Links need to be configured in Area 1. A Partiti ...

  • D-Link DFL-2560G - page 159

    The Virtual Link is configured between fw1 and fw2 on Area 1, as it is used as the transit area. In the configuration only the Router ID have to be configured, as in the example above show fw2 need to have a Virtual Link to fw1 with the Router ID 192.168.1.1 and vice versa. These VLinks need to be configured in Area 1. OSPF High Availability Suppor ...

  • D-Link DFL-2560G - page 160

    Example 4.7. Importing Routes from an OSPF AS into the Main Routing Table In this example, the routes received using OSPF will be added into the main routing table. First of all a Dynamic Routing Policy filter needs to be created. The filter needs to have a name, in this example ImportOSPFRoutes is used, as it explains what the filter does. The fil ...

  • D-Link DFL-2560G - page 161

    Web Interface 1. Go to Routing > Dynamic Routing Rules > Add > Dynamic routing policy rule 2. Specify a suitable name for the filter, for example ExportDefRoute 3. For From Routing Table select Main Routing Table 4. Choose wan for Destination Interface 5. Choose all-nets in the ...Exactly Matches list 6. Click OK Next, create an OSPF Actio ...

  • D-Link DFL-2560G - page 162

    4.6. Multicast Routing 4.6.1. Overview Certain types of Internet interactions, such as conferencing and video broadcasts, require a single client or host to send the same packet to multiple receivers. This could be achieved through the sender duplicating the packet with different receiving IP addresses or by a broadcast of the packet across the Int ...

  • D-Link DFL-2560G - page 163

    The multiplex rule can operate in one of two modes: Using IGMP The traffic flow specified by the multiplex rule must have been requested by hosts using IGMP before any multicast packets are forwarded through the specified interfaces. This is the default behavior of NetDefendOS. Not using IGMP The traffic flow will be forwarded according to the spec ...

  • D-Link DFL-2560G - page 164

    The matching rule could also be a NAT rule for source address translation (see below) but cannot be a FwdFast or SAT rule. Example 4.9. Forwarding of Multicast Traffic using the SAT Multiplex Rule In this example, we will create a multiplex rule in order to forward the multicast groups 239.192.10.0/24:1234 to the interfaces if1, if2 and if3. All gr ...

  • D-Link DFL-2560G - page 165

    The CLI command to create the multiplex rule is then: add IPRule SourceNetwork=<srcnet> SourceInterface=<srcif> DestinationInterface=<srcif> DestinationNetwork=<destnet> Action=MultiplexSAT Service=<service> MultiplexArgument={outif1;ip1},{outif2;ip2},{outif3;ip3}... The two values {outif;ip} represent a combination of ...

  • D-Link DFL-2560G - page 166

    Example 4.10. Multicast Forwarding - Address Translation The following SAT Multiplex rule needs to be configured to match the scenario described above: Web Interface A. Create a custom service for multicast called multicast_service : 1. Go to Objects > Services > Add > TCP/UDP 2. Now enter: • Name: multicast_service • Type: UDP • Des ...

  • D-Link DFL-2560G - page 167

    the multicast source is located on a network directly connected to the router. In this case, no query rule is needed. A second exception is if a neighboring router is statically configured to deliver a multicast stream to the NetDefend Firewall. In this case also, an IGMP query would not have to be specified. NetDefendOS supports two IGMP modes of ...

  • D-Link DFL-2560G - page 168

    4.6.3.1. IGMP Rules Configuration - No Address Translation This example describes the IGMP rules needed for configuring IGMP according to the No Address Translation scenario described above. We want our router to act as a host towards the upstream router and therefore we configure IGMP to run in proxy mode. Example 4.11. IGMP - No Address Translati ...

  • D-Link DFL-2560G - page 169

    • Multicast Source: 192.168.10.1 • Multicast Group: 239.192.10.0/24 4. Click OK 4.6.3.2. IGMP Rules Configuration - Address Translation The following examples illustrates the IGMP rules needed to configure IGMP according to the Address Translation scenario described above in Section 4.6.2.2, “Multicast Forwarding - Address Translation Scenari ...

  • D-Link DFL-2560G - page 170

    • Output: if1 (this is the relay interface) 3. Under Address Filter enter: • Source Interface: wan • Source Network: UpstreamRouterIp • Destination Interface: core • Destination Network: auto • Multicast Source: 192.168.10.1 • Multicast Group: 239.192.10.0/24 4. Click OK Example 4.13. if2 Configuration - Group Translation The followin ...

  • D-Link DFL-2560G - page 171

    3. Under Address Filter enter: • Source Interface: wan • Source Network: UpstreamRouterIp • Destination Interface: core • Destination Network: auto • Multicast Source: 192.168.10.1 • Multicast Group: 239.192.10.0/24 4. Click OK Advanced IGMP Settings There are a number of IGMP advanced settings which are global and apply to all interfac ...

  • D-Link DFL-2560G - page 172

    Default: IGMPv3 IGMP Last Member Query Interval The maximum time in milliseconds until a host has to send an answer to a group or group-and-source specific query. Global setting on interfaces without an overriding IGMP Setting. Default: 5,000 IGMP Max Total Requests The maximum global number of IGMP messages to process each second. Default: 1000 IG ...

  • D-Link DFL-2560G - page 173

    interfaces without an overriding IGMP Setting. Default: 30,000 IGMP Unsolicated Report Interval The time in milliseconds between repetitions of an initial membership report. Global setting on interfaces without an overriding IGMP Setting. Default: 1,000 4.6.4. Advanced IGMP Settings Chapter 4. Routing 173 ...

  • D-Link DFL-2560G - page 174

    4.7. Transparent Mode 4.7.1. Overview Transparent Mode Usage The NetDefendOS Transparent Mode feature allows a NetDefend Firewall to be placed at a point in a network without any reconfiguration of the network and without hosts being aware of its presence. All NetDefendOS features can then be used to monitor and manage traffic flowing through that ...

  • D-Link DFL-2560G - page 175

    . If the NetDefend Firewall is placed into a network for the first time, or if network topology changes, the routing configuration must therefore be checked and adjusted to ensure that the routing table is consistent with the new layout. Reconfiguration of IP settings may be required for pre-existing routers and protected servers. This works well w ...

  • D-Link DFL-2560G - page 176

    Discovery is done by NetDefendOS sending out ARP as well as ICMP (ping) requests, acting as the initiating sender of the original IP packet for the destination on the interfaces specified in the Switch Route . If an ARP reply is received, NetDefendOS will update the CAM table and Layer 3 Cache and forward the packet to the destination. If the CAM t ...

  • D-Link DFL-2560G - page 177

    associated with the switch routes, transparency will exist between them. For example, if the interfaces if1 to if6 appear in a switch routes in routing table A , the resulting interconnections will be as illustrated below. Connecting together switch routes in this way only applies, however, if all interfaces are associated with the same routing tab ...

  • D-Link DFL-2560G - page 178

    The recommended way to enable Transparent Mode is to add switch routes, as described above. An alternative method is to enable transparent mode directly on an interface (a check box for this is provided in the graphical user interfaces). When enabled in this way, default switch routes are automatically added to the routing table for the interface a ...

  • D-Link DFL-2560G - page 179

    Transparent Mode with a common address range (in this example 192.168.10.0/24 ). Figure 4.13. Transparent Mode Internet Access In this situation, any "normal" non-switch all-nets routes in the routing table should be removed and replaced with an all-nets switch route (not doing this is a common mistake during setup). This switch route wil ...

  • D-Link DFL-2560G - page 180

    The other consequence of not using NAT is that IP addresses of users accessing the Internet usually need to be public IP addresses. If NATing needs to be performed in the example above to hide individual addresses from the Internet, it would have to be done by a device (possibly another NetDefend Firewall) between the 192.168.10.0/24 network and th ...

  • D-Link DFL-2560G - page 181

    5. Now enter: • IP Address: 10.0.0.2 • Network: 10.0.0.0/24 • Transparent Mode: Enable 6. Click OK Configure the rules: 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: HTTPAllow • Action: Allow • Service: http • Source Interface: lan • Destination Interface: any • Source Network: 10.0.0.0/24 • Destination ...

  • D-Link DFL-2560G - page 182

    Example 4.15. Setting up Transparent Mode for Scenario 2 Configure a Switch Route over the LAN and DMZ interfaces for address range 10.0.0.0/24 (assume the WAN interface is already configured). Web Interface Configure the interfaces: 1. Go to Interfaces > Ethernet > Edit (lan) 2. Now enter: • IP Address: 10.0.0.1 • Network: 10.0.0.0/24 ? ...

  • D-Link DFL-2560G - page 183

    • Interfaces: Select lan and dmz 3. Click OK Configure the routing: 1. Go to Routing > Main Routing Table > Add > SwitchRoute 2. Now enter: • Switched Interfaces: TransparentGroup • Network: 10.0.0.0/24 • Metric: 0 3. Click OK Configure the rules: 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: HTTP-LAN-to ...

  • D-Link DFL-2560G - page 184

    • Destination Interface: dmz • Source Network: all-nets • Destination Network: wan_ip 9. Click OK 4.7.4. Spanning Tree BPDU Support NetDefendOS includes support for relaying the Bridge Protocol Data Units (BPDUs) across the NetDefend Firewall. BPDU frames carry Spanning Tree Protocol (STP) messages between layer 2 switches in a network. STP a ...

  • D-Link DFL-2560G - page 185

    Default: Enabled Decrement TTL Enable this if the TTL should be decremented each time a packet traverses the firewall in Transparent Mode. Default: Disabled Dynamic CAM Size This setting can be used to manually configure the size of the CAM table. Normally Dynamic is the preferred value to use. Default: Dynamic CAM Size If the Dynamic CAM Size sett ...

  • D-Link DFL-2560G - page 186

    Null Enet Sender Defines what to do when receiving a packet that has the sender hardware (MAC) address in ethernet header set to null (0000:0000:0000). Options: • Drop - Drop packets • DropLog - Drop and log packets Default: DropLog Broadcast Enet Sender Defines what to do when receiving a packet that has the sender hardware (MAC) address in et ...

  • D-Link DFL-2560G - page 187

    • Drop - Drop the packets • DropLog - Drop packets log the event Default: Drop Relay MPLS When set to Ignore all incoming MPLS packets are relayed in transparent mode. Options: • Ignore - Let the packets pass but do not log • Log - Let the packets pass and log the event • Drop - Drop the packets • DropLog - Drop packets log the event De ...

  • D-Link DFL-2560G - page 188

    4.7.5. Advanced Settings for Transparent Mode Chapter 4. Routing 188 ...

  • D-Link DFL-2560G - page 189

    Chapter 5. DHCP Services This chapter describes DHCP services in NetDefendOS. • Overview, page 189 • DHCP Servers, page 190 • Static DHCP Assignment, page 193 • DHCP Relaying, page 195 • IP Pools, page 198 5.1. Overview Dynamic Host Configuration Protocol (DHCP) is a protocol that allows network administrators to automatically assign IP n ...

  • D-Link DFL-2560G - page 190

    5.2. DHCP Servers DHCP servers assign and manage the IP addresses taken from a specified address pool. In NetDefendOS, DHCP servers are not limited to serving a single range of IP addresses but can use any IP address range that can be specified by a NetDefendOS IP address object. Multiple DHCP Servers The administrator has the ability to set up one ...

  • D-Link DFL-2560G - page 191

    • WINS Servers - WINS servers the client can use for WINS lookup. • Next Server - the IP address of the next server in the boot process, this is usually a TFTP server. In addition, Custom Options can be specified in order to have the DHCP servers hand out all options supported by the DHCP standard. Example 5.1. Setting up a DHCP server This exa ...

  • D-Link DFL-2560G - page 192

    10.4.13.241 00-0c-29-04-f8-3c ACTIVE(STATIC) 10.4.13.242 00-1e-0b-aa-ae-11 ACTIVE(STATIC) 10.4.13.243 00-1c-c4-36-6c-c4 INACTIVE(STATIC) 10.4.13.244 00-00-00-00-02-14 INACTIVE(STATIC) 10.4.13.254 00-00-00-00-02-54 INACTIVE(STATIC) 10.4.13.1 00-12-79-3b-dd-45 ACTIVE 10.4.13.2 00-12-79-c4-06-e7 ACTIVE 10.4.13.3 *00-a0-f8-23-45-a3 ACTIVE 10.4.13.4 *00 ...

  • D-Link DFL-2560G - page 193

    5.3. Static DHCP Assignment Where the administrator requires a fixed relationship between a client and the assigned IP address, NetDefendOS allows the assignment of a given IP to a specific MAC address. Example 5.3. Setting up Static DHCP This example shows how to assign the IP address 192.168.1.1 to the MAC address 00-90-12-13-14-15 . The examples ...

  • D-Link DFL-2560G - page 194

    Auto Save Policy What policy should be used to save the lease database to the disk, possible settings are Disabled , ReconfShut or ReconfShutTimer . Default: ReconfShut Lease Store Interval How often, in seconds, the leases database should be saved to disk if DHCPServer_SaveLeasePolicy is set to ReconfShutTimer . Default: 86400 5.3.1. DHCP Advanced ...

  • D-Link DFL-2560G - page 195

    5.4. DHCP Relaying The DHCP Problem With DHCP, clients send requests to locate the DHCP server(s) using broadcast messages. However, broadcasts are normally only propagated across the local network. This means that the DHCP server and client always need to be on the same physical network. In a large Internet-like network topology, this means there ...

  • D-Link DFL-2560G - page 196

    3. Click OK Adding a DHCP relayer called as vlan-to-dhcpserver : 1. Go to System > DHCP > Add > DHCP Relay 2. Now enter: • Name: vlan-to-dhcpserver • Action: Relay • Source Interface: ipgrp-dhcp • DHCP Server to relay to: ip-dhcp • Allowed IP offers from server: all-nets 3. Under the Add Route tab, check Add dynamic routes for th ...

  • D-Link DFL-2560G - page 197

    Max Auto Routes How many relays that can be active at the same time. Default: 256 Auto Save Policy What policy should be used to save the relay list to the disk, possible settings are Disabled , ReconfShut , or ReconfShutTimer . Default: ReconfShut Auto Save Interval How often, in seconds, should the relay list be saved to disk if DHCPServer_SaveRe ...

  • D-Link DFL-2560G - page 198

    5.5. IP Pools Overview IP pools are used to offer other subsystems access to a cache of DHCP IP addresses. These addresses are gathered into a pool by internally maintaining a series of DHCP clients (one per IP). The DHCP servers used by a pool can either be external or be DHCP servers defined in NetDefendOS itself. External DHCP servers can be spe ...

  • D-Link DFL-2560G - page 199

    Maximum free The maximum number of "free" IPs to be kept. Must be equal to or greater than the prefetch parameter. The pool will start releasing (giving back IPs to the DHCP server) when the number of free clients exceeds this value. Maximum clients Optional setting used to specify the maximum number of clients (IPs) allowed in the pool. ...

  • D-Link DFL-2560G - page 200

    5.5. IP Pools Chapter 5. DHCP Services 200 ...

  • D-Link DFL-2560G - page 201

    Chapter 6. Security Mechanisms This chapter describes NetDefendOS security features. • Access Rules, page 201 • ALGs, page 204 • Web Content Filtering, page 251 • Anti-Virus Scanning, page 268 • Intrusion Detection and Prevention, page 274 • Denial-of-Service Attack Prevention, page 285 • Blacklisting Hosts and Networks, page 289 6.1. ...

  • D-Link DFL-2560G - page 202

    VPNs provide one means of avoiding spoofing but where a VPN is not an appropriate solution then Access Rules can provide an anti-spoofing capability by providing an extra filter for source address verification. An Access Rule can verify that packets arriving at a given interface do not have a source address which is associated with a network of ano ...

  • D-Link DFL-2560G - page 203

    problems in case a rule is preventing some other function, such as VPN tunnel establishment, from working properly. Example 6.1. Setting up an Access Rule A rule is to be defined that ensures no traffic with a source address not within the lannet network is received on the lan interface. CLI gw-world:/> add Access Name=lan_Access Interface=lan N ...

  • D-Link DFL-2560G - page 204

    6.2. ALGs 6.2.1. Overview To complement low-level packet filtering, which only inspects packet headers in protocols such as IP, TCP, UDP, and ICMP, NetDefend Firewalls provide Application Layer Gateways (ALGs) which provide filtering at the higher application OSI level. An ALG object acts as a mediator in accessing commonly used Internet applicatio ...

  • D-Link DFL-2560G - page 205

    Maximum Connection Sessions The Service associated with an ALG has a configurable parameter associated with it called Max Sessions and the default value varies according to the type of ALG. For instance, the default value for the HTTP ALG is 1000 . This means that a 1000 connections are allowed in total for the HTTP Service across all interfaces. T ...

  • D-Link DFL-2560G - page 206

    when specifying URLs, as described below. • URL Whitelisting The opposite to blacklisting, this makes sure certain URLs are always allowed. Wildcarding can also be used for these URLs, as described below. It is important to note that whitelisting a URL means that it cannot be blacklisted and it also cannot be dropped by web content filtering (if ...

  • D-Link DFL-2560G - page 207

    download will be dropped. If nothing is marked in this mode then no files can be downloaded. Additional filetypes not included by default can be added to the Allow/Block list however these cannot be subject to content checking meaning that the file extension will be trusted as being correct for the contents of the file. Note: Similarities with othe ...

  • D-Link DFL-2560G - page 208

    Using Wildcards in White and Blacklists Entries made in the white and blacklists can make use of wildcarding to have a single entry be equivalent to a large number of possible URLs. The wildcard character " * " can be used to represent any sequence of characters. For example, the entry *.some_domain.com will block all pages whose URLs end ...

  • D-Link DFL-2560G - page 209

    Consider a scenario where an FTP client on the internal network connects through the firewall to an FTP server on the Internet. The IP rule is then configured to allow network traffic from the FTP client to port 21 on the FTP server. When active mode is used, NetDefendOS doesn't know that the FTP server will establish a new connection back to ...

  • D-Link DFL-2560G - page 210

    Anti-Virus Scanning The NetDefendOS Anti-Virus subsystem can be enabled to scan all FTP downloads searching for malicious code. Suspect files can be de dropped or just logged. This feature is common to a number of ALGs and is described fully in Section 6.4, “Anti-Virus Scanning” . FTP ALG with ZoneDefense Used together with the FTP ALG, ZoneDef ...

  • D-Link DFL-2560G - page 211

    To make it possible to connect to this server from the Internet using the FTP ALG, the FTP ALG and rules should be configured as follows: Web Interface A. Define the ALG: 1. Go to Objects > ALG > Add > FTP ALG 2. Enter Name: ftp-inbound 3. Check Allow client to use active mode 4. Uncheck Allow server to use passive mode 5. Click OK B. Defi ...

  • D-Link DFL-2560G - page 212

    • Name: SAT-ftp-inbound • Action: SAT • Service: ftp-inbound 3. For Address Filter enter: • Source Interface: any • Destination Interface: core • Source Network: all-nets • Destination Network: wan_ip (assuming the external interface has been defined as this) 4. For SAT check Translate the Destination IP Address 5. Enter To: New IP Ad ...

  • D-Link DFL-2560G - page 213

    Example 6.3. Protecting FTP Clients In this scenario shown below the NetDefend Firewall is protecting a workstation that will connect to FTP servers on the Internet. To make it possible to connect to these servers from the internal network using the FTP ALG, the FTP ALG and rules should be configured as follows: Web Interface A. Create the FTP ALG: ...

  • D-Link DFL-2560G - page 214

    Rules (Using Public IPs). The following rule needs to be added to the IP rules if using public IP's; make sure there are no rules disallowing or allowing the same kind of ports/traffic before these rules. The service in use is the ftp-outbound , which should be using the ALG definition ftp-outbound as described earlier. C. Allow connections to ...

  • D-Link DFL-2560G - page 215

    Allow/Disallow Read The TFTP GET function can be disabled so that files cannot be retrieved by a TFTP client. The default value is Allow . Allow/Disallow Write The TFTP PUT function can be disabled so that files cannot be written by a TFTP client. The default value is Allow. Remove Request Option Specifies if options should be removed from request. ...

  • D-Link DFL-2560G - page 216

    This is a very useful feature to have since it is possible to put in a block against either an infected client or an infected server sending large amounts of malware generated emails. Email size limiting A maximum allowable size of email messages can be specified. This feature counts the total amount of bytes sent for a single email which is the he ...

  • D-Link DFL-2560G - page 217

    4. Anti-virus scanning (if enabled). As described above, if an address is found on the whitelist then it will not be blocked if it also found on the blacklist. SPAM filtering, if it is enabled, is still applied to whitelisted addresses but emails flagged as SPAM will not be tagged nor dropped, only logged. Anti-virus scanning, if it is enabled, is ...

  • D-Link DFL-2560G - page 218

    The NetDefendOS SMTP ALG does not support all ESMTP extensions including Pipelining and Chunking . The ALG therefore removes any unsupported extensions from the supported extension list that is returned to the client by an SMTP server behind the NetDefend Firewall. When an extension is removed, a log message is generated with the text: unsupported_ ...

  • D-Link DFL-2560G - page 219

    security issue on the public Internet. Unsolicited email, sent out in massive quantities by groups known as spammers , can waste resources, transport malware as well as try to direct the reader to webpages which might exploit browser vulnerabilities. Integral to the NetDefendOS SMTP ALG is a SPAM module that provides the ability to apply spam filte ...

  • D-Link DFL-2560G - page 220

    weighted sum can then be calculated based on all responses. The administrator can configure one of the following actions based on the sum calculated: 1. Dropped If the sum is greater than or equal to a predefined Drop threshold then the email is considered to be definitely SPAM and is discarded or alternatively sent to a single, special mailbox. If ...

  • D-Link DFL-2560G - page 221

    And this is what the email's recipient will see in the summary of their inbox contents. The individual user could then decide to set up their own filters in the local client to deal with such tagged emails, possibly sending it to a separate folder. Adding X-SPAM Information If an email is determined to be SPAM and a forwarding address is confi ...

  • D-Link DFL-2560G - page 222

    allowed through if this happens. Setup Summary To set up DNSBL SPAM filtering in the SMTP ALG, the following list summarizes the steps: • Specify which DNSBL servers are to be used. There can be multiple and they can act both as backups to each other as well as confirmation of a sender's status. • Specify a weight for each server which wil ...

  • D-Link DFL-2560G - page 223

    The dnsbl CLI command provides a means to control and monitor the operation of the SPAM filtering module. The dnsbl command on its own without options shows the overall status of all ALGs. If the name of the SMTP ALG object on which DNSBL SPAM filtering is enabled is my_smtp_alg then the output would be: gw-world:/> dnsbl DNSBL Contexts: Name St ...

  • D-Link DFL-2560G - page 224

    6.2.6. The POP3 ALG POP3 is a mail transfer protocol that differs from SMTP in that the transfer of mail is directly from a server to a user's client software. POP3 ALG Options Key features of the POP3 ALG are: Block Clear Text Authentication Block connections between client and server that send the username/password combination as clear text ...

  • D-Link DFL-2560G - page 225

    Note: Traffic shaping will not work with the SIP ALG Any traffic connections that trigger an IP rule with a service object that uses the SIP ALG cannot be also subject to traffic shaping. SIP Components The following components are the logical building blocks for SIP communication: User Agents These are the end points or clients that are involved i ...

  • D-Link DFL-2560G - page 226

    Maximum Sessions per ID The number of simultaneous sessions that a single client can be involved with is restricted by this value. The default number is 5 . Maximum Registration Time The maximum time for registration with a SIP Registrar. The default value is 3600 seconds. SIP Signal Timeout The maximum time allowed for SIP sessions. The default va ...

  • D-Link DFL-2560G - page 227

    (sometimes described as SIP pinholes ) for allowing the media data traffic to flow through the NetDefend Firewall. Tip Make sure there are no preceding rules already in the IP rule set disallowing or allowing the same kind of traffic. SIP Usage Scenarios NetDefendOS supports a variety of SIP usage scenarios. The following three scenarios cover near ...

  • D-Link DFL-2560G - page 228

    The SIP proxy in the above diagram could alternatively be located remotely across the Internet. The proxy should be configured with the Record-Route feature enabled to insure all SIP traffic to and from the office clients will be sent through the SIP Proxy. This is recommended since the attack surface is minimized by allowing only SIP signalling fr ...

  • D-Link DFL-2560G - page 229

    sends its own IP address as contact information to the SIP proxy. NetDefendOS registers the client's local contact information and uses this to redirect incoming requests to the user. The ALG takes care of the address translations needed. 4. Ensure the clients are correctly configured. The SIP Proxy Server plays a key role in locating the curr ...

  • D-Link DFL-2560G - page 230

    This scenario can be implemented in two ways: • Using NAT to hide the network topology. • Without NAT so the network topology is exposed. Solution A - Using NAT Here, the proxy and the local clients are hidden behind the IP address of the NetDefend Firewall. The setup steps are as follows: 1. Define a single SIP ALG object using the options des ...

  • D-Link DFL-2560G - page 231

    If Record-Route is enabled then the Source Network for outbound traffic from proxy users can be further restricted in the above rules by using " ip_proxy " as indicated. When an incoming call is received, the SIP ALG will follow the SAT rule and forward the SIP request to the proxy server. The proxy will in turn, forward the request to it ...

  • D-Link DFL-2560G - page 232

    The exchanges illustrated are as follows: • 1,2 - An initial INVITE is sent to the outbound local proxy server on the DMZ. • 3,4 - The proxy server sends the SIP messages towards the destination on the Internet. • 5,6 - A remote client or proxy server replies to the local proxy server. • 7,8 - The local proxy forwards the reply to the local ...

  • D-Link DFL-2560G - page 233

    DMZ interface as the contact address. • An Allow rule for outbound traffic from the proxy behind the DMZ interface to the remote clients on the Internet. • An Allow rule for inbound SIP traffic from the SIP proxy behind the DMZ interface to the IP address of the NetDefend Firewall. This rule will have core (in other words, NetDefendOS itself) a ...

  • D-Link DFL-2560G - page 234

    • Destination Port set to 5060 (the default SIP signalling port) • Type set to TCP/UDP 3. Define four rules in the IP rule set: • An Allow rule for outbound traffic from the clients on the internal network to the proxy located on the DMZ interface. • An Allow rule for outbound traffic from the proxy behind the DMZ interface to the remote cl ...

  • D-Link DFL-2560G - page 235

    Gateways An H.323 gateway connects two dissimilar networks and translates traffic between them. It provides connectivity between H.323 networks and non-H.323 networks such as public switched telephone networks (PSTN), translating protocols and converting media streams. A gateway is not required for communication between two H.323 terminals. Gatekee ...

  • D-Link DFL-2560G - page 236

    • The H.323 ALG supports version 5 of the H.323 specification. This specification is built upon H.225.0 v5 and H.245 v10. • In addition to support voice and video calls, the H.323 ALG supports application sharing over the T.120 protocol. T.120 uses TCP to transport data while voice and video is transported over UDP. • To support gatekeepers, ...

  • D-Link DFL-2560G - page 237

    Web Interface Outgoing Rule: 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: H323AllowOut • Action: Allow • Service: H323 • Source Interface: lan • Destination Interface: any • Source Network: lannet • Destination Network: 0.0.0.0/0 (all-nets) • Comment: Allow outgoing calls 3. Click OK Incoming Rule: 1. Go t ...

  • D-Link DFL-2560G - page 238

    Example 6.5. H.323 with private IP addresses In this scenario a H.323 phone is connected to the NetDefend Firewall on a network with private IP addresses. To make it possible to place a call from this phone to another H.323 phone on the Internet, and to allow H.323 phones on the Internet to call this phone, we need to configure rules. The following ...

  • D-Link DFL-2560G - page 239

    • Destination Interface: core • Source Network: 0.0.0.0/0 (all-nets) • Destination Network: wan_ip (external IP of the firewall) • Comment: Allow incoming calls to H.323 phone at ip-phone 3. Click OK To place a call to the phone behind the NetDefend Firewall, place a call to the external IP address on the firewall. If multiple H.323 phones ...

  • D-Link DFL-2560G - page 240

    Incoming Rule: 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: H323AllowIn • Action: Allow • Service: H323 • Source Interface: any • Destination Interface: lan • Source Network: 0.0.0.0/0 (all-nets) • Destination Network: lannet • Comment: Allow incoming calls 3. Click OK Example 6.7. Using Private IP Address ...

  • D-Link DFL-2560G - page 241

    • Source Interface: any • Destination Interface: core • Source Network: 0.0.0.0/0 (all-nets) • Destination Network: wan_ip (external IP of the firewall) • Comment: Allow incoming calls to H.323 phone at ip-phone 3. For SAT enter Translate Destination IP Address: To New IP Address: ip-phone (IP address of phone) 4. Click OK 1. Go to Rules ...

  • D-Link DFL-2560G - page 242

    Web Interface Incoming Gatekeeper Rules: 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: H323In • Action: SAT • Service: H323-Gatekeeper • Source Interface: any • Destination Interface: core • Source Network: 0.0.0.0/0 (all-nets) • Destination Network: wan_ip (external IP of the firewall) • Comment: SAT rule ...

  • D-Link DFL-2560G - page 243

    2. Now enter: • Name: H323In • Action: Allow • Service: H323-Gatekeeper • Source Interface: lan • Destination Interface: dmz • Source Network: lannet • Destination Network: ip-gatekeeper (IP address of the gatekeeper) • Comment: Allow incoming communication with the Gatekeeper 3. Click OK Note: Outgoing calls do not need a specific ...

  • D-Link DFL-2560G - page 244

    • Name: H323Out • Action: NAT • Service: H323-Gatekeeper • Source Interface: lan • Destination Interface: any • Source Network: lannet • Destination Network: 0.0.0.0/0 (all-nets) • Comment: Allow outgoing communication with a gatekeeper 3. Click OK Note: Outgoing calls do not need a specific rule There is no need to specify a specif ...

  • D-Link DFL-2560G - page 245

    The head office has placed a H.323 Gatekeeper in the DMZ of the corporate NetDefend Firewall. This firewall should be configured as follows: Web Interface 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: LanToGK • Action: Allow • Service: H323-Gatekeeper • Source Interface: lan • Destination Interface: dmz • Sourc ...

  • D-Link DFL-2560G - page 246

    • Source Interface: lan • Destination Interface: dmz • Source Network: lannet • Destination Network: ip-gateway • Comment: Allow H.323 entities on lannet to call phones connected to the H.323 Gateway on the DMZ 3. Click OK 1. Go to Rules > IP Rules > Add > IPRule 2. Now enter: • Name: GWToLan • Action: Allow • Service: H323 ...

  • D-Link DFL-2560G - page 247

    3. Click OK Example 6.11. Configuring remote offices for H.323 If the branch and remote office H.323 phones and applications are to be configured to use the H.323 Gatekeeper at the head office, the NetDefend Firewalls in the remote and branch offices should be configured as follows: (this rule should be in both the Branch and Remote Office firewall ...

  • D-Link DFL-2560G - page 248

    the communication between "external" phones and the Gatekeeper to make sure that it is possible for internal phones to call the external phones that are registered with the gatekeeper. 6.2.9. The TLS ALG Overview Transport Layer Security (TLS) is a protocol that provides secure communications over the public Internet between two end point ...

  • D-Link DFL-2560G - page 249

    Advantages of Using NetDefendOS for TLS Termination TLS can be implemented directly in the server to which clients connect, however, if the servers are protected behind a NetDefend Firewall, then NetDefendOS can take on the role of the TLS endpoint. NetDefendOS then performs TLS authentication, encryption and unencryption of data to/from clients an ...

  • D-Link DFL-2560G - page 250

    6. Optionally, a SAT rule can be created to change the destination port for the unencrypted traffic. Alternatively an SLB_SAT rule can be used to do load balancing (the destination port can also be changed through a custom service object). URLs Delivered by Servers It should be noted that using NetDefendOS for TLS termination will not change URLs i ...

  • D-Link DFL-2560G - page 251

    6.3. Web Content Filtering 6.3.1. Overview Web traffic is one of the biggest sources for security issues and misuse of the Internet. Inappropriate surfing habits can expose a network to many security threats as well as legal and regulatory liabilities. Productivity and Internet bandwidth can also be impaired. Filtering Mechanisms Through the HTTP A ...

  • D-Link DFL-2560G - page 252

    Removing such legitimate code could, at best, cause the web site to look distorted, at worst, cause it to not work in a browser at all. Active Content Handling should therefore only be used when the consequences are well understood. Example 6.13. Stripping ActiveX and Java applets This example shows how to configure a HTTP Application Layer Gateway ...

  • D-Link DFL-2560G - page 253

    */*.gif Good. This will block all files with .gif as the file name extension. www.example.com Bad. This will only block the first request to the web site. Surfing to www.example.com/index.html , for example, will not be blocked. *example.com/* Bad. This will also cause www.myexample.com to be blocked since it blocks all sites ending with example.co ...

  • D-Link DFL-2560G - page 254

    7. Click OK Finally, make an exception from the blacklist by creating a whitelist: 1. Go to Objects > ALG 2. In the table, click on the recently created HTTP ALG to view its properties 3. Click the HTTP URL tab 4. Now click Add and select HTTP ALG URL from the menu 5. Select Whitelist as the Action 6. In the URL textbox, enter www.D-Link.com/*.e ...

  • D-Link DFL-2560G - page 255

    Figure 6.6. Dynamic Content Filtering Flow If the requested web page URL is not present in the databases, then the webpage content at the URL will automatically be downloaded to D-Link's central data warehouse and automatically analyzed using a combination of software techniques. Once categorized, the URL is distributed to the global databases ...

  • D-Link DFL-2560G - page 256

    Dynamic Content Filtering is a feature that is enabled by taking out a separate subscription to the service. This is an addition to the normal NetDefendOS license. Once a subscription is taken out, an HTTP Application Layer Gateway (ALG) Object should be defined with Dynamic Content Filtering enabled. This object is then associated with a Service o ...

  • D-Link DFL-2560G - page 257

    5. In the Blocked Categories list, select Search Sites and click the >> button. 6. Click OK Then, create a Service object using the new HTTP ALG: 1. Go to Local Objects > Services > Add > TCP/UDP service 2. Specify a suitable name for the Service, for example http_content_filtering 3. Select the TCP in the Type dropdown list 4. Enter ...

  • D-Link DFL-2560G - page 258

    This example is based on the same scenario as the previous example, but now with audit mode enabled. CLI First, create an HTTP Application Layer Gateway (ALG) Object: gw-world:/> add ALG ALG_HTTP content_filtering WebContentFilteringMode=Audit FilteringCategories=SEARCH_SITES Web Interface First, create an HTTP Application Layer Gateway (ALG) Ob ...

  • D-Link DFL-2560G - page 259

    will include a dropdown list containing all available categories. If the user believes the requested web site is wrongly classified, he can select a more appropriate category from the dropdown list and submit that as a proposal. The URL to the requested web site as well as the proposed category will then be sent to D-Link's central data wareho ...

  • D-Link DFL-2560G - page 260

    this are web sites that contain information relating to sexuality and sexual health, which may be classified under the Health Sites Category (21). Examples might be: • www.naughtychix.com • www.fullonxxx.com Category 2: News A web site may be classified under the News category if its content includes information articles on recent events pertai ...

  • D-Link DFL-2560G - page 261

    A web site may be classified under the Shopping category if its content includes any form of advertisement of goods or services to be exchanged for money, and may also include the facilities to perform that transaction online. Included in this category are market promotions, catalogue selling and merchandising services. Examples might be: • www.m ...

  • D-Link DFL-2560G - page 262

    A web site may be classified under the Investment Sites category if its content includes information, services or facilities pertaining to personal investment. URLs in this category include contents such as brokerage services, online portfolio setup, money management forums or stock quotes. This category does not include electronic banking faciliti ...

  • D-Link DFL-2560G - page 263

    • www.sportstoday.com • www.soccerball.com Category 17: www-Email Sites A web site may be classified under the www-Email Sites category if its content includes online, web-based email facilities. Examples might be: • www.coldmail.com • mail.yazoo.com Category 18: Violence / Undesirable A web site may be classified under the Violence / Undes ...

  • D-Link DFL-2560G - page 264

    Category 22: Clubs and Societies A web site may be classified under the Clubs and Societies category if its content includes information or services of relating to a club or society. This includes team or conference web sites. Examples might be: • www.sierra.org • www.walkingclub.org Category 23: Music Downloads A web site may be classified und ...

  • D-Link DFL-2560G - page 265

    • www.admessages.com • www.tripleclick.com Category 28: Drugs/Alcohol A web site may be classified under the Drugs/Alcohol category if its content includes drug and alcohol related information or services. Some URLs categorized under this category may also be categorized under the Health category. Examples might be: • www.the-cocktail-guide.c ...

  • D-Link DFL-2560G - page 266

    particular installation's needs. The WebUI provides a simple way to download, edit and upload these files. The available files are: CompressionForbidden ContentForbidden URLForbidden RestrictedSiteNotice ReclassifyURL To perform customization it is necessary to first create a new, named ALG Banner Files object. This new object automatically co ...

  • D-Link DFL-2560G - page 267

    2. A new ALG Banner Files object must exist which the edited file(s) is uploaded to. If the object is called mytxt , the CLI command to create this object is: gw-world:/> add HTTPALGBanners mytxt This creates an object which contains a copy of all the Default content filtering banner files. 3. The modified file is then uploaded using SCP. It is ...

  • D-Link DFL-2560G - page 268

    6.4. Anti-Virus Scanning 6.4.1. Overview The NetDefendOS Anti-Virus module protects against malicious code carried in file downloads. Files may be downloaded as part of a web-page in an HTTP transfer, in an FTP download, or perhaps as an attachment to an email delivered through SMTP. Malicious code in such downloads can have different intents rangi ...

  • D-Link DFL-2560G - page 269

    Types of File Downloads Scanned As described above, Anti-Virus scanning is enabled on a per ALG basis and can scan file downloads associated with the HTTP, FTP, SMTP and POP3 ALGs. More specifically: • Any uncompressed file type transferred through these ALGs can be scanned. • If the download has been compressed, ZIP and GZIP file downloads can ...

  • D-Link DFL-2560G - page 270

    6.4.4. The Signature Database SafeStream NetDefendOS Anti-Virus scanning is implemented by D-Link using the "SafeStream" virus signature database. The SafeStream database is created and maintained by Kaspersky, a company which is a world leader in the field of virus detection. The database provides protection against virtually all known v ...

  • D-Link DFL-2560G - page 271

    3. Compression Ratio Limit When scanning compressed files, NetDefendOS must apply decompression to examine the file's contents. Some types of data can result in very high compression ratios where the compressed file is a small fraction of the original uncompressed file size. This can mean that a comparatively small compressed file attachment m ...

  • D-Link DFL-2560G - page 272

    4. When the update is completed, the newly active unit also downloads the files for the update and performs a reconfiguration. 5. This second reconfiguration causes another failover so the passive unit reverts back to being active again. These steps result in both NetDefend Firewalls in a cluster having updated databases and with the original activ ...

  • D-Link DFL-2560G - page 273

    1. Go to Objects > ALG > Add > HTTP ALG 2. Specify a suitable name for the ALG, for instance anti_virus 3. Click the Antivirus tab 4. Select Protect in the Mode dropdown list 5. Click OK B. Then, create a Service object using the new HTTP ALG: 1. Go to Local Objects > Services > Add > TCP/UDP service 2. Specify a suitable name for ...

  • D-Link DFL-2560G - page 274

    6.5. Intrusion Detection and Prevention 6.5.1. Overview Intrusion Definition Computer servers can sometimes have vulnerabilities which leave them exposed to attacks carried by network traffic. Worms, trojans and backdoor exploits are examples of such attacks which, if successful, can potentially compromise or take control of a server. A generic ter ...

  • D-Link DFL-2560G - page 275

    • Maintenance IDP Maintenance IDP is the base IDP system included as standard with the NetDefend DFL 210, 800, 1600 and 2500. Maintenance IDP is a simplified IDP that gives basic protection against IDP attacks. It is upgradeable to the higher level and more comprehensive Advanced IDP which is discussed next. IDP does not come as standard with the ...

  • D-Link DFL-2560G - page 276

    configurable interval. This is done via an HTTP connection to the D-Link server network which delivers the latest signature database updates. If the server's signature database has a newer version than the current local database, the new database will be downloaded, replacing the older version. The Terms IDP , IPS and IDS The terms Intrusion D ...

  • D-Link DFL-2560G - page 277

    Each IDP rule has a section of settings for HTTP normalization . This allows the administrator to choose the actions that should be taken when IDP finds inconsistencies in the URIs embedded in incoming HTTP requests. Some server attacks are based on creating URIs with sequences that can exploit weaknesses in some HTTP server products. The URI condi ...

  • D-Link DFL-2560G - page 278

    Insertion Attacks An Insertion attack consists of inserting data into a stream so that the resulting sequence of data packets is accepted by the IDP subsystem but will be rejected by the targeted application. This results is two different streams of data. As an example, consider a data stream broken up into 4 packets: p1, p2, p3 and p4. The attacke ...

  • D-Link DFL-2560G - page 279

    In order for IDP to correctly identify an attack, it uses a profile of indicators, or pattern , associated with different types of attack. These predefined patterns, also known as signatures , are stored in a local NetDefendOS database and are used by the IDP module to analyze traffic for attack patterns. Each IDP signature is designated by a uniqu ...

  • D-Link DFL-2560G - page 280

    IDP Signature Groups fall into a three level hierarchical structure. The top level of this hierarchy is the signature Type , the second level the Category and the third level the Sub-Category . The signature group called POLICY_DB_MSSQL illustrates this principle where Policy is the Type , DB is the Category and MSSQL is the Sub-Category . These 3 ...

  • D-Link DFL-2560G - page 281

    scanning can make the load on the firewall hardware unnecessarily high, adversely affecting throughput. 6.5.7. IDP Actions Action Options After pattern matching recognizes an intrusion in traffic subject to an IDP Rule, the Action associated with that Rule is taken. The administrator can associate one of three Action options with an IDP Rule: • I ...

  • D-Link DFL-2560G - page 282

    wait 600 seconds (equivalent to 10 minutes) before sending a new email. An SMTP server is assumed to have been configured in the address book with the name smtp-server . CLI Adding an SMTP log receiver: gw-world:/> add LogReceiver LogReceiverSMTP smt4IDP IPAddress=smtp-server Receiver1=youremail@yourcompany.com IDP Rules: gw-world:/> cc IDPRu ...

  • D-Link DFL-2560G - page 283

    An IDP rule called IDPMailSrvRule will be created, and the Service to use is the SMTP service. Source Interface and Source Network defines where traffic is coming from, in this example the external network. The Destination Interface and Destination Network define where traffic is directed to, in this case the mail server. Destination Network should ...

  • D-Link DFL-2560G - page 284

    Specify the Action: An action is now defined, specifying what signatures the IDP should use when scanning data matching the rule, and what NetDefendOS should do when a possible intrusion is detected. In this example, intrusion attempts will cause the connection to be dropped, so Action is set to Protect . The Signatures option is set to IPS_MAIL_SM ...

  • D-Link DFL-2560G - page 285

    6.6. Denial-of-Service Attack Prevention 6.6.1. Overview By embracing the Internet, enterprises experience new business opportunities and growth. The enterprise network and the applications that run over it are business critical. Not only can a company reach a larger number of customers via the Internet, it can serve them faster and more efficientl ...

  • D-Link DFL-2560G - page 286

    intended victim. "Jolt" is simply a purpose-written program for generating such packets on operating systems whose ping commands refuse to generate oversized packets. The triggering factor is that the last fragment makes the total packet size exceed 65535 bytes, which is the highest number that a 16-bit integer can store. When the value o ...

  • D-Link DFL-2560G - page 287

    • By stripping the URG bit by default from all TCP segments traversing the system (configurable via Advanced Settings > TCP > TCPUrg ). WinNuke attacks will usually show up in NetDefendOS logs as normal drops with the name of the rule in your policy that disallowed the connection attempt. For connections allowed through the system, "TC ...

  • D-Link DFL-2560G - page 288

    6.6.8. TCP SYN Flood Attacks The TCP SYN Flood attack works by sending large amounts of TCP SYN packets to a given port and then not responding to SYN ACKs sent in response. This will tie up local TCP stack resources on the victim machine until it is unable to respond to more SYN packets until the existing half-open connections have timed out. NetD ...

  • D-Link DFL-2560G - page 289

    6.7. Blacklisting Hosts and Networks Overview NetDefendOS implements a Blacklist of host or network IP addresses which can be utilized to protect against traffic coming from specific Internet sources. Certain NetDefendOS subsystems have the ability to optionally blacklist a host or network when certain conditions are encountered. These subsystems a ...

  • D-Link DFL-2560G - page 290

    blacklisted, it still does not prevent NetDefendOS mechanisms such as Threshold Rules from dropping or denying connections from that source. What whitelisting does is prevent a source being added to a blacklist if that is the action a rule has specified. For further details on usage see Section 6.5.7, “IDP Actions” , Section 10.3.8, “Threshol ...

  • D-Link DFL-2560G - page 291

    6.7. Blacklisting Hosts and Networks Chapter 6. Security Mechanisms 291 ...

  • D-Link DFL-2560G - page 292

    Chapter 7. Address Translation This chapter describes NetDefendOS address translation capabilities. • NAT, page 292 • NAT Pools, page 297 • SAT, page 300 The ability of NetDefendOS to change the IP address of packets as they pass through the NetDefend Firewall is known as address translation . The ability to transform one IP address to anothe ...

  • D-Link DFL-2560G - page 293

    NAT provides many-to-one translation . This means that each NAT rule in the IP rule set will translate between several source IP addresses and a single source IP address. To maintain session state information, each connection from dynamically translated addresses uses a unique port number and IP address combination as its sender. NetDefendOS perfor ...

  • D-Link DFL-2560G - page 294

    many NAT pools and a single pool can be used in more than one NAT rule. This topic is discussed further in Section 7.2, “NAT Pools” . Applying NAT Translation The following illustrates how NAT is applied in practice on a new connection: 1. The sender, for example 192.168.1.5, sends a packet from a dynamically assigned port, for instance, port 1 ...

  • D-Link DFL-2560G - page 295

    1. Go to Rules > IP Rules > Add > IPRule 2. Specify a suitable name for the rule, for example NAT_HTTP 3. Now enter: • Action: NAT • Service: http • Source Interface: lan • Source Network: lannet • Destination Interface: any • Destination Network: all-nets 4. Under the NAT tab, make sure that the Use Interface Address option is ...

  • D-Link DFL-2560G - page 296

    We shall examine the typical case where the NetDefend Firewall acts as a PPTP server and terminates the PPTP tunnel for PPTP clients. Clients that wish to be anonymous, communicate with their local ISP using PPTP. The traffic is directed to the anonymizing service provider where a NetDefend Firewall is installed to act as the PPTP server for the cl ...

  • D-Link DFL-2560G - page 297

    7.2. NAT Pools Overview As discussed in Section 7.1, “NAT” , NAT provides a way to have multiple internal clients and hosts with unique private internal IP addresses communicate to remote hosts through a single external public IP address. When multiple public external IP addresses are available then a NAT Pool object can be used to allocate new ...

  • D-Link DFL-2560G - page 298

    Stateless NAT Pools The Stateless option means that no state table is maintained and the external IP address chosen for each new connection is the one that has the least connections already allocated to it. This means two connections between one internal host to the same external host may use two different external IP addresses. The advantage of a ...

  • D-Link DFL-2560G - page 299

    Web Interface A. First create an object in the address book for the address range: 1. Go to Objects > Address Book > Add > IP address 2. Specify a suitable name for the IP range nat_pool_range 3. Enter 10.6.13.10-10.16.13.15 in the IP Address textbox (a network such as 10.6.13.0/24 could be used here - the 0 and 255 addresses will be autom ...

  • D-Link DFL-2560G - page 300

    7.3. SAT NetDefendOS can translate entire ranges of IP addresses and/or ports. Such translations are transpositions, each address or port is mapped to a corresponding address or port in the new range, rather than translating them all to the same address or port. In NetDefendOS this functionality is known as Static Address Translation (SAT). Note: P ...

  • D-Link DFL-2560G - page 301

    DestinationNetwork=wan_ip SATTranslate=DestinationIP SATTranslateToIP=10.10.10.5 Name=SAT_HTTP_To_DMZ Then create a corresponding Allow rule: gw-world:/main> add IPRule action=Allow Service=http SourceInterface=any SourceNetwork=all-nets DestinationInterface=core DestinationNetwork=wan_ip Name=Allow_HTTP_To_DMZ Web Interface First create a SAT r ...

  • D-Link DFL-2560G - page 302

    hide: # Action Src Iface Src Net Dest Iface Dest Net Parameters 3 NAT lan lannet any all-nets All Now, what is wrong with this rule set? If we assume that we want to implement address translation for reasons of security as well as functionality, we discover that this rule set makes our internal addresses visible to machines in the DMZ. When interna ...

  • D-Link DFL-2560G - page 303

    # Action Src Iface Src Net Dest Iface Dest Net Parameters 1 SAT any all-nets core wan_ip http SETDEST wwwsrv 80 2 Allow any all-nets core wan_ip http These two rules allow us to access the web server via the NetDefend Firewall's external IP address. Rule 1 states that address translation can take place if the connection has been permitted, and ...

  • D-Link DFL-2560G - page 304

    In this way, the reply arrives at PC1 from the expected address. Another possible solution to this problem is to allow internal clients to speak directly to 10.0.0.2 and this would completely avoid all the problems associated with address translation. However, this is not always practical. 7.3.2. Translation of Multiple IP Addresses (M:N) A single ...

  • D-Link DFL-2560G - page 305

    gw-world:/> add Address IP4Address wwwsrv_priv_base Address=10.10.10.5 Publish the public IP addresses on the wan interface using ARP publish. One ARP item is needed for every IP address: gw-world:/> add ARP Interface=wan IP=195.55.66.77 mode=Publish Repeat this for all the five public IP addresses. Next, change the current category to be the ...

  • D-Link DFL-2560G - page 306

    • Servce: http • Source Interface: any • Source Network: all-nets • Destination Interface: wan • Destination Network: wwwsrv_pub 4. Switch to the SAT tab 5. Make sure that the Destination IP Address option is selected 6. In the New IP Address dropdown list, select wwwsrv_priv 7. Click OK Finally, create a corresponding Allow rule: 1. Go t ...

  • D-Link DFL-2560G - page 307

    # Action Src Iface Src Net Dest Iface Dest Net Parameters 1 SAT any all-nets wan wwwsrv_pub TCP 80-85 SETDEST 192.168.0.50 1080 This rule produces a 1:1 translation of all ports in the range 80 - 85 to the range 1080 - 1085. • Attempts to communicate with the web servers public address - port 80, will result in a connection to the web servers pri ...

  • D-Link DFL-2560G - page 308

    if anyone tries to connect to the public address of the web server, the destination address will be changed to its private address. # Action Src Iface Src Net Dest Iface Dest Net Parameters 1 SAT lan lannet wwwsrv_pub TCP 80-85 SETDEST intrasrv 1080 2 SAT any all-nets wwwsrv_pub TCP 80-85 SETDEST wwwsrv-priv 1080 In this instance, both rules are se ...

  • D-Link DFL-2560G - page 309

    • Return traffic from wwwsrv:80 will match rules 2 and 3. The replies will therefore be dynamically address translated. This changes the source port to a completely different port, which will not work. The problem can be solved using the following rule set: # Action Src Iface Src Net Dest Iface Dest Net Parameters 1 SAT any all-nets core wan_ip h ...

  • D-Link DFL-2560G - page 310

    7.3.7. SAT and FwdFast Rules Chapter 7. Address Translation 310 ...

  • D-Link DFL-2560G - page 311

    Chapter 8. User Authentication This chapter describes how NetDefendOS implements user authentication. • Overview, page 311 • Authentication Setup, page 313 • Customizing HTML Pages, page 325 8.1. Overview In situations where individual users connect to protected resources through the NetDefend Firewall, the administrator will often require th ...

  • D-Link DFL-2560G - page 312

    • Changed on a regular basis such as every three months. 8.1. Overview Chapter 8. User Authentication 312 ...

  • D-Link DFL-2560G - page 313

    8.2. Authentication Setup 8.2.1. Setup Summary The following list summarizes the steps for User Authentication setup with NetDefendOS: • Set up a database of users, each with a username/password combination. This can exist locally in a NetDefendOS User DB object, or remotely on a RADIUS server and will be designated as the Authentication Source . ...

  • D-Link DFL-2560G - page 314

    RADIUS with NetDefendOS NetDefendOS acts as a RADIUS client, sending user credentials and connection parameter information as a RADIUS message to a nominated RADIUS server. The server processes the requests and sends back a RADIUS message to accept or deny them. One or more external servers can be defined in NetDefendOS. RADIUS Security To provide ...

  • D-Link DFL-2560G - page 315

    unreachable. The default value for this setting is 5 . • Name Attribute The name of the field in the LDAP server containing the username. The default value is uid . This should be set to samaccountname if using Active Directory. • Retrieve Group Membership If this option is enabled, group memberships will be received from the database. The Memb ...

  • D-Link DFL-2560G - page 316

    LDAP server authentication is automatically configured to work using LDAP Bind Request Authentication . This means that authentication succeeds if successful connection is made to the LDAP server. Individual clients are not distinguished from one another. LDAP server referrals should not occur with bind request authentication but if they do, the se ...

  • D-Link DFL-2560G - page 317

    command: gw-world:/> show LDAPDatabase <object_name> The entire contents of the database can be displayed with the command: gw-world:/> show LDAPDatabase LDAP Authentication and PPP When using a PPP based client for PPTP or L2TP access, special consideration has to be taken if LDAP authentication is to succeed with CHAP, MS-CHAPv1 or MS ...

  • D-Link DFL-2560G - page 318

    compare with the digest sent by the client. A successful digest match then results in successful authentication. The essential difference with the normal event sequence in A above is that it is the NetDefend Firewall itself which is performing the authentication. Figure 8.2. LDAP for PPP with CHAP, MS-CHAPv1 or MS-CHAPv2 When setting up this scenar ...

  • D-Link DFL-2560G - page 319

    • The Local database defined within NetDefendOS. • A RADIUS server (discussed below). • An external LDAP server database (discussed below). A further option, Disallow , can be used so that a negative rule can be created which says "never authenticate given these conditions". This option might be used, for instance, to never authenti ...

  • D-Link DFL-2560G - page 320

    8.2.6. Authentication Processing The list below describes the processing flow through NetDefendOS for username/password authentication: 1. A user creates a new connection to the NetDefend Firewall. 2. NetDefendOS sees the new user connection on an interface and checks the Authentication rule set to see if there is a matching rule for traffic on thi ...

  • D-Link DFL-2560G - page 321

    Options . These are: • Login Type - This can be one of: • FORM - The user is presented with an HTML page for authentication which is filled in and the data sent back to NetDefendOS with a POST. • BASICAUTH - This sends a 401 - Authentication Required message back to the browser which will cause it to use its own inbuilt dialog to ask the user ...

  • D-Link DFL-2560G - page 322

    The SAT rule catches all unauthenticated requests and must be set up with an all-to-one address mapping that directs them to the address 127.0.0.1 which corresponds to core (NetDefendOS itself). 8.2.7. HTTP Authentication Chapter 8. User Authentication 322 ...

  • D-Link DFL-2560G - page 323

    Example 8.1. Creating an Authentication User Group In the example of an authentication address object in the Address Book, a user group "users" is used to enable user authentication on "lannet". This example shows how to configure the user group in the NetDefendOS database. Web Interface Step A 1. Go to User Authentication > ...

  • D-Link DFL-2560G - page 324

    • Destination Network lan_ip 3. Click OK B. Set up the Authentication Rule 1. Go to User Authentication > User Authentication Rules > Add > User Authentication Rule 2. Now enter: • Name: HTTPLogin • Agent: HTTP • Authentication Source: Local • Interface: lan • Originator IP: lannet 3. For Local User DB choose lannet_auth_users ...

  • D-Link DFL-2560G - page 325

    f. Shared Secret: Enter a text string here for basic encryption of the RADIUS messages g. Confirm Secret: Retype the string to confirm the one typed above 3. Click OK 8.3. Customizing HTML Pages User Authentication makes use of a set of HTML files to present information to the user during the authentication process. The options available for HTTP a ...

  • D-Link DFL-2560G - page 326

    • %IPADDR% - The IP address which is being browsed from. • %REASON% - The reason that access was denied. • - The web page URL for redirects. The %REDIRURL% Parameter In certain banner web pages, the parameter %REDIRURL% appears. This is a placeholder for the original URL which was requested before the user login screen appeared for an unauthe ...

  • D-Link DFL-2560G - page 327

    2. A new Auth Banner Files object must exist which the edited file(s) is uploaded to. If the object is called ua_html , the CLI command to create this object is: gw-world:/> add HTTPAuthBanners ua_html This creates an object which contains a copy of all the Default user auth banner files. 3. The modified file is then uploaded using SCP. It is up ...

  • D-Link DFL-2560G - page 328

    8.3. Customizing HTML Pages Chapter 8. User Authentication 328 ...

  • D-Link DFL-2560G - page 329

    Chapter 9. VPN This chapter describes the Virtual Private Network (VPN) functionality in NetDefendOS. • Overview, page 329 • VPN Quick Start, page 333 • IPsec Components, page 343 • IPsec Tunnels, page 357 • PPTP/L2TP, page 375 • CA Server Access, page 383 • VPN Troubleshooting, page 386 9.1. Overview 9.1.1. VPN Usage The Internet is ...

  • D-Link DFL-2560G - page 330

    2. Client to LAN connection - Where many remote clients need to connect to an internal network over the Internet. In this case, the internal network is protected by the NetDefend Firewall to which the client connects and the VPN tunnel is set up between them. 9.1.2. VPN Encryption Encryption of VPN traffic is done using the science of cryptography ...

  • D-Link DFL-2560G - page 331

    • Restricting access through the VPN to needed services only, since mobile computers are vulnerable. • Creating DMZs for services that need to be shared with other companies through VPNs. • Adapting VPN access policies for different groups of users. • Creating key distribution policies. Endpoint Security A common misconception is that VPN-c ...

  • D-Link DFL-2560G - page 332

    “The TLS ALG” . 9.1.5. The TLS Alternative for VPN Chapter 9. VPN 332 ...

  • D-Link DFL-2560G - page 333

    9.2. VPN Quick Start Overview Later sections in this chapter will explore VPN components in detail. To help put those later sections in context, this section is a quick start summary of the steps needed for VPN setup. It outlines the individual steps in setting up VPNs for the most common scenarios. These are: • IPsec LAN to LAN with Pre-shared K ...

  • D-Link DFL-2560G - page 334

    9.2.1. IPsec LAN to LAN with Pre-shared Keys 1. Create a Pre-shared Key object. 2. Optionally create a new IKE Algorithms object and/or an IPsec Algorithms object if the default algorithm proposal lists do not provide a set of algorithms that are acceptable to the tunnel remote end point. This will depend on the capabilities of the device at the ot ...

  • D-Link DFL-2560G - page 335

    Action Src Interface Src Network Dest Interface Dest Network Service Allow ipsec_tunnel remote_net lan lannet All The Service used in these rules is All but it could be a predefined service. 6. Define a new NetDefendOS Route which specifies that the VPN Tunnel ipsec_tunnel is the Interface to use for routing packets bound for the remote network at ...

  • D-Link DFL-2560G - page 336

    considered adequate. Two self-signed certificates are required and the same two are used at either end of the tunnel but their usage is reversed. In other words: one certificate is used as the root certificate at one end, call it Side A , and as the host certificate at the other end, call it Side B . The second certificate is used in the opposite w ...

  • D-Link DFL-2560G - page 337

    The Group string for a user can be specified if its group's access is to be restricted to certain source networks. Group can be specified (with the same text string) in the Authentication section of an IP object. If that IP object is then used as the Source Network of a rule in the IP rule set, that rule will only apply to a user if their Grou ...

  • D-Link DFL-2560G - page 338

    • Create a Config Mode Pool object (there can only be one associated with a NetDefendOS installation) and in it specify the address range. • Enable the IKE Config Mode option in the IPsec Tunnel object ipsec_tunnel . 2. If client IP addresses are to be retrieved through DHCP: • Create an IP Pool object and in it specify the DHCP server to use ...

  • D-Link DFL-2560G - page 339

    Note: The system time and date should be correct The NetDefendOS date and time should be set correctly since certificates have an expiry date and time. Also review Section 9.6, “CA Server Access” , which describes important considerations for certificate validation. 9.2.5. L2TP Roaming Clients with Pre-Shared Keys Due to the inbuilt L2TP client ...

  • D-Link DFL-2560G - page 340

    • Set Outer Interface Filter to ipsec_tunnel . • Set Outer Server IP to ip_ext . • Select the Microsoft Point-to-Point Encryption allowed. Since IPsec encryption is used this can be set to be None only, otherwise double encryption will degrade throughput. • Set IP Pool to l2tp_pool . • Enable Proxy ARP on the int interface to which the in ...

  • D-Link DFL-2560G - page 341

    2. Load a Gateway Certificate and Root Certificate into NetDefendOS. 3. When setting up the IPsec Tunnel object, specify the certificates to use under Authentication . This is done by: a. Enable the X.509 Certificate option. b. Select the Gateway Certificate. c. Add the Root Certificate to use. 4. If using the Windows XP L2TP client, the appropriat ...

  • D-Link DFL-2560G - page 342

    3. Define a User Authentication Rule, this is almost identical to L2TP: Agent Auth Source Src Network Interface Client Source IP PPP Local all-nets pptp_tunnel all-nets (0.0.0.0/0) 4. Now set up the IP rules in the IP rule set: Action Src Interface Src Network Dest Interface Dest Network Service Allow pptp_tunnel pptp_pool any int_net All NAT pptp_ ...

  • D-Link DFL-2560G - page 343

    9.3. IPsec Components 9.3.1. Overview Internet Protocol Security (IPsec) is a set of protocols defined by the Internet Engineering Task Force (IETF) to provide IP security at the network layer. An IPsec based VPN is made up of two parts: • Internet Key Exchange protocol (IKE) • IPsec protocols (AH/ESP/both) The first part, IKE, is the initial n ...

  • D-Link DFL-2560G - page 344

    describing the incoming traffic, and the other the outgoing. In cases where ESP and AH are used in conjunction, four SAs will be created. IKE Negotiation The process of negotiating session parameters consists of a number of phases and modes. These are described in detail in the below sections. The flow of events can be summarized as follows: IKE Ph ...

  • D-Link DFL-2560G - page 345

    However, since we do not want to publish to much of the negotiation in plaintext, we first agree upon a way of protecting the rest of the IKE negotiation. This is done, as described in the previous section, by the initiator sending a proposal-list to the responder. When this has been done, and the responder accepted one of the proposals, we try to ...

  • D-Link DFL-2560G - page 346

    This way, an eavesdropper will only see encrypted traffic going from one of VPN endpoint to another. In transport mode, the traffic will not be tunneled, and is hence not applicable to VPN tunnels. It can be used to secure a connection from a VPN client directly to the NetDefend Firewall, for example for IPsec protected remote configuration. This s ...

  • D-Link DFL-2560G - page 347

    IKE Encryption This specifies the encryption algorithm used in the IKE negotiation, and depending on the algorithm, the size of the encryption key used. The algorithms supported by NetDefendOS IPsec are: • AES • Blowfish • Twofish • Cast128 • 3DES • DES DES is only included to be interoperable with other older VPN implementations. The u ...

  • D-Link DFL-2560G - page 348

    PFS DH Group This specifies the Diffie-Hellman group to use with PFS. The available DH groups are discussed below. IPsec DH Group This specifies the Diffie-Hellman group to use for IPsec communication. The available DH groups are discussed below in the section titled Diffie-Hellman Groups . IPsec Encryption The encryption algorithm that will be use ...

  • D-Link DFL-2560G - page 349

    by NetDefendOS are as follows: • DH group 1 (768-bit) • DH group 2 (1024-bit) • DH group 5 (1536-bit) All these HA groups are available for use with IKE, IPsec and PFS. 9.3.3. IKE Authentication Manual Keying The "simplest" way of configuring a VPN is by using a method called manual keying . This is a method where IKE is not used at ...

  • D-Link DFL-2560G - page 350

    One thing that has to be considered when using Pre-Shared Keys is key distribution. How are the Pre-Shared Keys distributed to remote VPN clients and firewalls? This is a major issue, since the security of a PSK system is based on the PSKs being secret. Should one PSK be compromised, the configuration will need to be changed to use a new PSK. Certi ...

  • D-Link DFL-2560G - page 351

    AH uses a cryptographic hash function to produce a MAC from the data in the IP packet. This MAC is then transmitted with the packet, allowing the remote endpoint to verify the integrity of the original IP packet, making sure the data has not been tampered with on its way through the Internet. Apart from the IP packet data, AH also authenticates par ...

  • D-Link DFL-2560G - page 352

    Achieving NAT Detection To achieve NAT detection both IPsec peers send hashes of their own IP addresses along with the source UDP port used in the IKE negotiations. This information is used to see whether the IP address and source port each peer uses is the same as what the other peer sees. If the source address and port have not changed, then the ...

  • D-Link DFL-2560G - page 353

    There are two types of proposal lists, IKE proposal lists and IPsec proposal lists. IKE lists are used during IKE Phase-1 (IKE Security Negotiation), while IPsec lists are using during IKE Phase-2 (IPsec Security Negotiation). Several algorithm proposal lists are already defined by default in NetDefendOS for different VPN scenarios and user defined ...

  • D-Link DFL-2560G - page 354

    9.3.7. Pre-shared Keys Pre-Shared Keys are used to authenticate VPN tunnels. The keys are secrets that are shared by the communicating parties before communication takes place. To communicate, both parties prove that they know the secret. The security of a shared secret depends on how "good" a passphrase is. Passphrases that are common wo ...

  • D-Link DFL-2560G - page 355

    9.3.8. Identification Lists When certificates are used as authentication method for IPsec tunnels, the NetDefend Firewall will accept all remote devices or VPN clients that are capable of presenting a certificate signed by any of the trusted Certificate Authorities. This can be a potential problem, especially when using roaming clients. A Typical S ...

  • D-Link DFL-2560G - page 356

    1. Go to Objects > VPN Objects > ID List > Add > ID List 2. Enter a name for the list, for example MyIDList 3. Click OK Then, create an ID: 1. Go to Objects > VPN Objects > IKE ID List > Add > ID List 2. Select MyIDList 3. Enter a name for the ID, for example JohnDoe 4. Select Distinguished name in the Type control 5. Now en ...

  • D-Link DFL-2560G - page 357

    9.4. IPsec Tunnels 9.4.1. Overview An IPsec Tunnel defines an endpoint of an encrypted tunnel. Each IPsec Tunnel is interpreted as a logical interface by NetDefendOS, with the same filtering, traffic shaping and configuration capabilities as regular interfaces. Remote Initiation of Tunnel Establishment When another NetDefend Firewall or another IPs ...

  • D-Link DFL-2560G - page 358

    IPsec Tunnel Quick Start This section covers IPsec tunnels in some detail. A quick start checklist of setup steps for these protocols in typical scenarios can be found in the following sections: • Section 9.2.1, “IPsec LAN to LAN with Pre-shared Keys” . • Section 9.2.2, “IPsec LAN to LAN with Certificates” . • Section 9.2.3, “IPsec ...

  • D-Link DFL-2560G - page 359

    the algorithm proposal lists that are pre-configured in NetDefendOS. 9.4.3.1. PSK based client tunnels Example 9.4. Setting up a PSK based VPN tunnel for roaming clients This example describes how to configure an IPsec tunnel at the head office NetDefend Firewall for roaming clients that connect to the office to gain remote access. The head office ...

  • D-Link DFL-2560G - page 360

    clients that connect to the office to gain remote access. The head office network uses the 10.0.1.0/24 network span with external firewall IP wan_ip. Web Interface A. Create a Self-signed Certificate for IPsec authentication: The step to actually create self-signed certificates is performed outside the WebUI using a suitable software product. The c ...

  • D-Link DFL-2560G - page 361

    E. Finally configure the IP rule set to allow traffic inside the tunnel. 9.4.3.3. Tunnels Based on CA Server Certificates Setting up client tunnels using a CA issued certificate is largely the same as using Self-signed certificates with the exception of a couple of steps. Most importantly, it is the responsibility of the administrator to acquire th ...

  • D-Link DFL-2560G - page 362

    • Encapsulation Mode: Tunnel 3. For Algorithms enter: • IKE Algorithms: Medium or High • IPsec Algorithms: Medium or High 4. For Authentication enter: • Choose X.509 Certificates as the authentication method • Root Certificate(s): Select your CA server root certificate imported earlier and add it to the Selected list • Gateway Certifica ...

  • D-Link DFL-2560G - page 363

    Example 9.7. Setting Up Config Mode In this example, the Config Mode Pool object is enabled by associating with it an already configured IP Pool object called ip_pool1. Web Interface 1. Go to Objects > VPN Objects > IKE Config Mode Pool 2. The Config Mode Pool object properties web page now appears 3. Select Use a predefined IPPool object 4. ...

  • D-Link DFL-2560G - page 364

    This example shows how to manually setup and specify an LDAP server. CLI gw-world:/> add LDAPServer Host=192.168.101.146 Username=myusername Password=mypassword Port=389 Web Interface 1. Go to Objects > VPN Objects > LDAP > Add > LDAP Server 2. Now enter: • IP Address: 192.168.101.146 • Username: myusername • Password: mypasswo ...

  • D-Link DFL-2560G - page 365

    Complete ikesnoop command options can be found in the CLI Reference Guide . The Client and the Server The two parties involved in the tunnel negotiation are referred to in this section as the client and server . In this context, the word " client " is used to refer to the device which is the initiator of the negotiation and the server ref ...

  • D-Link DFL-2560G - page 366

    Life type : Kilobytes Life duration : 50000 Transform 4/4 Transform ID : IKE Encryption algorithm : 3DES-cbc Hash algorithm : SHA Authentication method : Pre-Shared Key Group description : MODP 1024 Life type : Seconds Life duration : 43200 Life type : Kilobytes Life duration : 50000 VID (Vendor ID) Payload data length : 16 bytes Vendor ID : 8f 9c ...

  • D-Link DFL-2560G - page 367

    IkeSnoop: Sending IKE packet to 192.168.0.10:500 Exchange type : Identity Protection (main mode) ISAKMP Version : 1.0 Flags : Cookies : 0x6098238b67d97ea6 -> 0x5e347cb76e95a Message ID : 0x00000000 Packet length : 224 bytes # payloads : 8 Payloads: SA (Security Association) Payload data length : 52 bytes DOI : 1 (IPsec DOI) Proposal 1/1 Protocol ...

  • D-Link DFL-2560G - page 368

    Packet length : 220 bytes # payloads : 4 Payloads: KE (Key Exchange) Payload data length : 128 bytes NONCE (Nonce) Payload data length : 16 bytes NAT-D (NAT Detection) Payload data length : 16 bytes NAT-D (NAT Detection) Payload data length : 16 bytes Step 4. Server Sends Key Exchange Data The Server now sends key exchange data back to the client. ...

  • D-Link DFL-2560G - page 369

    Explanation of Above Values Flags: E means encryption (it is the only flag used). ID: Identification of the client The Notification field is given as Initial Contact to indicate this is not a re-key. Step 6. Server ID Response The server now responds with its own ID. IkeSnoop: Sending IKE packet to 192.168.0.10:500 Exchange type : Identity Protecti ...

  • D-Link DFL-2560G - page 370

    Transform ID : Rijndael (aes) Key length : 128 Authentication algorithm : HMAC-SHA-1 SA life type : Seconds SA life duration : 21600 SA life type : Kilobytes SA life duration : 50000 Encapsulation mode : Tunnel Transform 3/4 Transform ID : Blowfish Key length : 128 Authentication algorithm : HMAC-MD5 SA life type : Seconds SA life duration : 21600 ...

  • D-Link DFL-2560G - page 371

    Packet length : 156 bytes # payloads : 5 Payloads: HASH (Hash) Payload data length : 16 bytes SA (Security Association) Payload data length : 56 bytes DOI : 1 (IPsec DOI) Proposal 1/1 Protocol 1/1 Protocol ID : ESP SPI Size : 4 SPI Value : 0xafba2d15 Transform 1/1 Transform ID : Rijndael (aes) Key length : 128 Authentication algorithm : HMAC-MD5 SA ...

  • D-Link DFL-2560G - page 372

    Tunnels if the latter is changed. This linkage is broken once IPsec Max Rules is altered manually so that subsequent changes to IPsec Max Tunnels will not cause an automatic change in IPsec Max Rules . Default: 4 times the license limit of IPsec Max Tunnels IPsec Max Tunnels Specifies the total number of tunnels allowed by NetDefendOS. This value i ...

  • D-Link DFL-2560G - page 373

    When the signature of a user certificate is verified, NetDefendOS looks at the issuer name field in the user certificate to find the CA certificate the certificate was signed by. The CA certificate may in turn be signed by another CA, which may be signed by another CA, and so on. Each certificate will be verified until one that has been marked as & ...

  • D-Link DFL-2560G - page 374

    This setting is used with IKEv1 only. Default: 2 (in other words, 2 x 10 = 20 seconds) DPD Expire Time The length of time in seconds for which DPD messages will be sent to the peer. If the peer has not responded to messages during this time it is considered to be dead. In other words, the length of time in seconds for which DPD-R-U-THERE messages w ...

  • D-Link DFL-2560G - page 375

    9.5. PPTP/L2TP The access by a client using a modem link over dial-up public switched networks, possibly with an unpredictable IP address, to protected networks via a VPN poses particular problems. Both the PPTP and L2TP protocols provide two different means of achieving VPN access from remote clients. The most commonly used feature that is relevan ...

  • D-Link DFL-2560G - page 376

    TCP port 1723 and/or IP protocol 47 before the PPTP connection can be made to the NetDefend Firewall. Examining the log can indicate if this problem occurred, with a log message of the following form appearing: Error PPP lcp_negotiation_stalled ppp_terminated Example 9.10. Setting up a PPTP server This example shows how to setup a PPTP Network Serv ...

  • D-Link DFL-2560G - page 377

    This example shows how to setup a L2TP Network Server. The example assumes that you have created some address objects in the Address Book. You will have to specify the IP address of the L2TP server interface, an outer IP address (that the L2TP server should listen to) and an IP pool that the L2TP server will use to give out IP addresses to the clie ...

  • D-Link DFL-2560G - page 378

    • Username: testuser • Password: mypassword • Confirm Password: mypassword 5. Click OK Now we will setup the IPsec Tunnel, which will later be used in the L2TP section. As we are going to use L2TP, the Local Network is the same IP as the IP that the L2TP tunnel will connect to, wan_ip. Furthermore, the IPsec tunnel needs to be configured to d ...

  • D-Link DFL-2560G - page 379

    Web Interface 1. Go to Interfaces > L2TP Servers > Add > L2TPServer 2. Enter a name for the L2TP tunnel, for example l2tp_tunnel 3. Now enter: • Inner IP Address: lan_ip • Tunnel Protocol: L2TP • Outer Interface Filter: l2tp_ipsec • Server IP: wan_ip 4. Under the PPP Parameters tab, check the Use User Authentication Rules control 5 ...

  • D-Link DFL-2560G - page 380

    DestinationInterface=any DestinationNetwork=all-nets name=AllowL2TP gw-world:/main> add IPRule action=NAT Service=all_services SourceInterface=l2tp_tunnel SourceNetwork=l2tp_pool DestinationInterface=any DestinationNetwork=all-nets name=NATL2TP Web Interface 1. Go to Rules > IP Rules > Add > IPRule 2. Enter a name for the rule, for exam ...

  • D-Link DFL-2560G - page 381

    Max PPP Resends The maximum number of PPP layer resends. Default: 10 9.5.4. PPTP/L2TP Clients The PPTP and L2TP protocols are described in the previous section. In addition to being able to act as a PPTP or L2TP server, NetDefendOS also offers the ability to act as a PPTP or L2TP clients. This can be useful if PPTP or L2TP is preferred as the VPN p ...

  • D-Link DFL-2560G - page 382

    If Dial On Demand is enabled then the PPTP/L2TP tunnel will not be set up until traffic is sent on the interface. The parameters for this option are: • Activity Sense - Specifies if dial-on-demand should trigger on Send or Recv or both. • Idle Timeout - The time of inactivity in seconds to wait before disconnection. Using the PPTP Client Featur ...

  • D-Link DFL-2560G - page 383

    9.6. CA Server Access Overview Where certificates are used, the two sides of a VPN tunnel exchange their certificates during the tunnel setup negotiation and either may then try to validate the received certificate by accessing a CA server . A certificate contains a URL (the CRL Distribution Point ) which specifies the validating CA server and serv ...

  • D-Link DFL-2560G - page 384

    3. The CA server is a commercial server on the public Internet. In this, the simplest case, public DNS servers will resolve the FQDN. The only requirement is that NetDefendOS will need to have at least one public DNS server address configured to resolve the FQDNs in the certificates it receives. • It must be also possible for an HTTP PUT request ...

  • D-Link DFL-2560G - page 385

    As explained previously, the address of the private CA server must be resolvable through public DNS servers for certificate validation requests coming from the public Internet. If the certificate queries are coming only from the NetDefend Firewall and the CA server is on the internal side of the firewall then the IP address of the internal DNS serv ...

  • D-Link DFL-2560G - page 386

    9.7. VPN Troubleshooting General Troubleshooting In all types of VPNs some basic troubleshooting checks can be made: • Check that all IP addresses have been specified correctly. • Check that all pre-shared keys and usernames/passwords are correctly entered. • Use ICMP Ping to confirm that the tunnel is working. With roaming clients this is be ...

  • D-Link DFL-2560G - page 387

    • Check that the correct certificates have been used. • Check that the certificate .cer and .key files have the same filename. For example, my_cert.key and my_cert.cer . • Check that the certificates have not expired. • Check that the NetDefendOS date and time is set correctly and consider time-zone issues with newly generated certificates ...

  • D-Link DFL-2560G - page 388

    single tunnel by specifying the IP address of the tunnel's endpoint (this is either the IP of the remote endpoint or a client's IP address). The command takes the form: ikesnoop -on <ip-address> -verbose Ikesnoop can be turned off with the command: ikesnoop -off For a more detailed discussion of this topic, see Section 9.4.5, “Tro ...

  • D-Link DFL-2560G - page 389

    Management Interface Failure with VPN Chapter 9. VPN 389 ...

  • D-Link DFL-2560G - page 390

    Chapter 10. Traffic Management This chapter describes how NetDefendOS can manage network traffic. • Traffic Shaping, page 390 • IDP Traffic Shaping, page 407 • Threshold Rules, page 412 • Server Load Balancing, page 414 10.1. Traffic Shaping 10.1.1. Introduction QoS with TCP/IP A weakness of TCP/IP is the lack of true Quality of Service (Qo ...

  • D-Link DFL-2560G - page 391

    Traffic Shaping Objectives Traffic shaping operates by measuring and queuing IP packets with respect to a number of configurable parameters. The objectives are: • Applying bandwidth limits and queuing packets that exceed configured limits, then sending them later when bandwidth demands are lower. • Dropping packets if packet buffers are full. T ...

  • D-Link DFL-2560G - page 392

    needed in an ISP scenario where individual pipes are allocated to each client. Pipe Rules Pipe Rules make up the Pipe Rule set . Each Rule is defined much like other NetDefendOS policies: by specifying the source/destination interface/network as well as the Service to which the rule is to apply. Once a new connection is permitted by the IP rule set ...

  • D-Link DFL-2560G - page 393

    It is important to understand that traffic shaping will not work with connection that are established because of a FwdFast rule in the NetDefendOS IP rule set. The reason for this is that traffic shaping is implemented based on the NetDefendOS state engine and a FwdFast IP rule does not set up a connection in the state engine. Packets bypass the st ...

  • D-Link DFL-2560G - page 394

    pass through the std-in pipe. CLI gw-world:/> add PipeRule ReturnChain=std-in SourceInterface=lan SourceNetwork=lannet DestinationInterface=wan DestinationNetwork=all-nets Service=all_services name=Outbound Web Interface 1. Go to Traffic Management > Traffic Shaping > Add > Pipe Rule 2. Specify a suitable name for the pipe, for instance ...

  • D-Link DFL-2560G - page 395

    Example 10.2. Limiting Bandwidth in Both Directions Create a second pipe for outbound traffic: CLI gw-world:/> add Pipe std-out LimitKbpsTotal=2000 Web Interface 1. Go to Traffic Management > Traffic Shaping > Pipes > Add > Pipe 2. Specify a name for the pipe, for example std-out 3. Enter 2000 in Total textbox 4. Click OK After creat ...

  • D-Link DFL-2560G - page 396

    This is not a bandwidth guarantee for web browsing but it is a 125 kbps bandwidth guarantee for everything except web browsing. For web browsing the normal rules of first-come, first-forwarded will apply when competing for bandwidth. This may mean 125 kbps, but it may also mean much slower speed if the connection is flooded. Setting up pipes in thi ...

  • D-Link DFL-2560G - page 397

    The minimum and maximum precedences define the precedence range that the pipe will handle. If a packet arrives with an already allocated precedence below the minimum then its precedence is changed to the minimum. Similarly, if a packet arrives with an already allocated precedence above the maximum, its precedence is changed to the maximum. For each ...

  • D-Link DFL-2560G - page 398

    pipe's configuration is exceeded. Lower priority packets will be buffered and sent when higher priority traffic uses less than the maximum specified for the pipe. The buffering process is sometimes referred to as "throttling back" since it reduces the flow rate. The Need for Guarantees A problem can occur however if the prioritized t ...

  • D-Link DFL-2560G - page 399

    Keep the forward chain of both rules as std-out only. Again, to simplify this example, we concentrate only on inbound traffic, which is the direction that is the most likely to be the first one to fill up in client-oriented setups. Set the return chain of the port 22 rule to ssh-in followed by std-in . Set the return chain of the port 23 rule to te ...

  • D-Link DFL-2560G - page 400

    computer A is not the same as port 1024 of computer B and individual connections are identifiable. If grouping by network is chosen, the network size should also be specified (this has the same meaning as the netmask). A Simple Groups Scenario If the total bandwidth limit for a pipe is 400 bps and we want to allocate this bandwidth amongst many des ...

  • D-Link DFL-2560G - page 401

    knows what its capacity is and the precedence mechanism is totally dependent on this. Pipe limits for VPN Traffic shaping measures the traffic inside VPN tunnels. This is the raw unencrypted data without any protocol overhead so it will be less than the actual VPN traffic. VPN protocols such as IPsec can add significant overhead to the data and for ...

  • D-Link DFL-2560G - page 402

    consumed by parties outside of administrator control but sharing the same connection. Troubleshooting For a better understanding of what is happening in a live setup, the console command: pipe -u <pipename> can be used to display a list of currently active users in each pipe. 10.1.11. A Summary of Traffic Shaping NetDefendOS traffic shaping p ...

  • D-Link DFL-2560G - page 403

    The reason for using 2 different pipes in this case, is that these are easier to match to the physical link capacity. This is especially true with asynchronous links such as ADSL. First, two pipes called in-pipe and out-pipe need to be created with the following parameters: Pipe Name Min Prec Def Prec Max Prec Grouping Net size Pipe limit in-pipe 0 ...

  • D-Link DFL-2560G - page 404

    • Priority 0 - Web plus remaining from other levels To implement this scheme, we can use the in-pipe and out-pipe . We first enter the Pipe Limits for each pipe. These limits correspond to the list above and are: • Priority 6 - 500 • Priority 4 - 250 • Priority 2 - 1000 Now create the Pipe Rules : Rule Name Forward Pipes Return Pipes Source ...

  • D-Link DFL-2560G - page 405

    The pipe chaining can be used as a solution to the problem of VPN overhead. A limit which allows for this overhead is placed on the VPN tunnel traffic and non-VPN traffic is inserted into a pipe that matches the speed of the physical link. To do this we first create separate pipes for the outgoing traffic and the incoming traffic. VoIP traffic will ...

  • D-Link DFL-2560G - page 406

    If SAT is being used, for example with a web server or ftp server, that traffic also needs to be forced into pipes or it will escape traffic shaping and ruin the planned quality of service. In addition, server traffic is initiated from the outside so the order of pipes needs to be reversed: the forward pipe is the in-pipe and the return pipe is the ...

  • D-Link DFL-2560G - page 407

    10.2. IDP Traffic Shaping 10.2.1. Overview The IDP Traffic Shaping feature is traffic shaping that is performed based on information coming from the NetDefendOS Intrusion Detection and Prevention (IDP) subsystem (for more information on IDP see Section 6.5, “Intrusion Detection and Prevention” ). The Problem of Bandwidth Usage A prime use of ID ...

  • D-Link DFL-2560G - page 408

    afterwards when other connections will be opened and subject to traffic shaping. Connections opened after the Time Window has expired will no longer be subject to traffic shaping. A Time Window value of 0 means that only traffic flowing over the initial triggering connection will be subject to traffic shaping. Any associated connections that do not ...

  • D-Link DFL-2560G - page 409

    Network range but not host X . This tells NetDefendOS that host X is not relevant in making a decision about including new non-IDP-triggering connections in traffic shaping. It may seem counter-intuitive that client B is also included in the Network range but this is done on the assumption that client B is a user whose traffic might also have to be ...

  • D-Link DFL-2560G - page 410

    IDP traffic shaping has a special CLI command associated with it called idppipes and this can examine and manipulate the hosts which are currently subject to traffic shaping. To display all hosts being traffic shaped by IDP Traffic Shaping, the command would be: gw-world:/> idppipes -show Host kbps Tmout ----------- ---- ---- 192.168.1.1 100 58 ...

  • D-Link DFL-2560G - page 411

    If the administrator wants to guarantee a bandwidth level, say 10 Megabits, for an application then an IDP rule can be set up to trigger for that application with the Pipe action specifying the bandwidth required. The traffic shaping pipes that are then automatically created get the highest priority by default and are therefore guaranteed that band ...

  • D-Link DFL-2560G - page 412

    10.3. Threshold Rules 10.3.1. Overview The objective of a Threshold Rule is to have a means of detecting abnormal connection activity as well as reacting to it. An example of a cause for such abnormal activity might be an internal host becoming infected with a virus that is making repeated connections to external IP addresses. It might alternativel ...

  • D-Link DFL-2560G - page 413

    • Network Based - The threshold is applied to all connections matching the rules as a group. 10.3.4. Rule Actions When a Threshold Rule is triggered one of two responses are possible: • Audit - Leave the connection intact but log the event. • Protect - Drop the triggering connection. Logging would be the preferred option if the appropriate tr ...

  • D-Link DFL-2560G - page 414

    10.4. Server Load Balancing 10.4.1. Overview The Server Load Balancing (SLB) feature in NetDefendOS is a powerful tool that can improve the following aspects of network applications: • Performance • Scalability • Reliability • Ease of administration The primary benefit of SLB is to allow the network service load to be shared across multiple ...

  • D-Link DFL-2560G - page 415

    The Additional Benefits of SLB Besides from improving performance and scalability, SLB provides a number of other benefits: • SLB increases the reliability of network applications by actively monitoring the servers sharing the load. SLB can detect when a server fails or becomes congested and will not direct any further requests to that server unt ...

  • D-Link DFL-2560G - page 416

    to the same host. Network Stickiness This mode is similar to IP stickiness except that by using a subnet mask, a range of hosts in a subnet can be specified. 10.4.4. The Distribution Algorithm There are several ways to determine how a load is shared across a server farm. NetDefendOS SLB supports the following algorithms: Round Robin The algorithm d ...

  • D-Link DFL-2560G - page 417

    When the Round Robin algorithm is used, the first arriving requests R1 and R2 from Client 1 are both assigned to one sever, say Server 1 , according to stickiness. The next request R3 from Client 2 is then routed to Server 2 . When R4 from Client 3 arrives, Server 1 gets back its turn again and will be assigned with R4 . Figure 10.10. Stickiness an ...

  • D-Link DFL-2560G - page 418

    10.4.5. Server Health Monitoring SLB uses Server Health Monitoring to continuously check the condition of the servers in an SLB configuration. SLB can monitor different OSI layers to check the condition of each server. Regardless of the algorithms used, if a server is deemed to have failed, SLB will not open any more connections to it until the ser ...

  • D-Link DFL-2560G - page 419

    Rule Name Rule Type Src. Interface Src. Network Dest. Interface Dest. Network WEB_SLB_ALW Allow any all-nets core ip_ext Note that the destination interface is specified as core , meaning NetDefendOS itself deals with this. The key advantage of having a separate Allow rule is that the webservers can log the exact IP address that is generating exter ...

  • D-Link DFL-2560G - page 420

    1. Go to Rules > IP Rule Sets > main > Add > IP Rule 2. Enter: • Name: Web_SLB_NAT • Action: NAT • Service: HTTP • Source Interface: lan • Source Network: lannet • Destination Interface: core • Destination Network: ip_ext 3. Click OK E. Specify an Allow IP rule for the external clients: 1. Go to Rules > IP Rule Sets > ...

  • D-Link DFL-2560G - page 421

    10.4.6. SLB_SAT Rules Chapter 10. Traffic Management 421 ...

  • D-Link DFL-2560G - page 422

    Chapter 11. High Availability This chapter describes the high availability fault-tolerance feature in NetDefend Firewalls. • Overview, page 422 • HA Mechanisms, page 424 • HA Setup, page 427 • HA Issues, page 431 • HA Advanced Settings, page 432 11.1. Overview HA Clusters NetDefendOS High Availability (HA) provides a fault tolerant capabi ...

  • D-Link DFL-2560G - page 423

    The heartbeat mechanism is discussed below in more depth in Section 11.2, “HA Mechanisms” . Cluster Management An HA Cluster of two NetDefend Firewalls is managed as a single unit with a unique cluster name which appears in the management interface as a single logical NetDefend Firewall. Administration operations such as changing rules in the I ...

  • D-Link DFL-2560G - page 424

    11.2. HA Mechanisms This section discusses im more depth the mechanisms NetDefendOS uses to implement the high availability feature. Basic Principles D-Link HA provides a redundant, state-synchronized hardware configuration. The state of the active unit, such as the connection table and other vital information, is continuously copied to the inactiv ...

  • D-Link DFL-2560G - page 425

    Failover Time The time for failover is typically about one second which means that clients may experience a failover as a slight burst of packet loss. In the case of TCP, the failover time is well within the range of normal retransmit timeouts so TCP will retransmit the lost packets within a very short space of time, and continue communication. UDP ...

  • D-Link DFL-2560G - page 426

    will lose their synchronization with each other. In other words, the inactive unit will no longer have a correct copy of the state of the active unit. A failover will not occur in this situation since the inactive unit will realize that synchronization has been lost. Failure of the sync interface results in the generation of hasync_connection_faile ...

  • D-Link DFL-2560G - page 427

    11.3. HA Setup This section provides a step-by-step guide for setting up an HA Cluster. 11.3.1. HA Hardware Setup The steps for the setup of hardware in an HA cluster are as follows: 1. Start with two physically similar NetDefend Firewalls. Both may be newly purchased or an existing unit may have a new unit added to it. The master hardware does not ...

  • D-Link DFL-2560G - page 428

    Typical HA Cluster Network Connections The illustration below shows the arrangement of typical HA Cluster connections in a network. All interfaces on the master unit would normally also have corresponding interfaces on the slave unit and these would be connected to the same networks. This is achieved by connecting the same interfaces on both master ...

  • D-Link DFL-2560G - page 429

    2. Go to System > High Availability . 3. Check the Enable High Availability checkbox. 4. Set the Cluster ID . This must be unique for each cluster. 5. Choose the Sync Interface . 6. Select the node type to be Master . 7. Go to Objects > Address Book and create an IP4 HA Address object for each interface pair. Each must contain the master and ...

  • D-Link DFL-2560G - page 430

    number on the right is the maximum number of connections allowed by the license. The following points are also relevant to cluster setup: • If this is not the first cluster in a network then the Cluster ID must be changed for the cluster so that it is unique (the default value is 0 ). The Cluster ID determines that the MAC address for the cluster ...

  • D-Link DFL-2560G - page 431

    11.4. HA Issues The following points should be kept in mind when managing and configuring an HA Cluster. SNMP SNMP statistics are not shared between master and slave. SNMP managers have no failover capabilities. Therefore both firewalls in a cluster need to be polled separately. Using Individual IP Addresses The unique individual IP addresses of th ...

  • D-Link DFL-2560G - page 432

    11.5. HA Advanced Settings The following NetDefendOS advanced settings are available for High Availability: Sync Buffer Size How much sync data, in Kbytes, to buffer while waiting for acknowledgments from the cluster peer. Default: 1024 Sync Packet Max Burst The maximum number of state sync packets to send in a burst. Default: 20 Initial Silence Th ...

  • D-Link DFL-2560G - page 433

    11.5. HA Advanced Settings Chapter 11. High Availability 433 ...

  • D-Link DFL-2560G - page 434

    Chapter 12. ZoneDefense This chapter describes the D-Link ZoneDefense feature. • Overview, page 434 • ZoneDefense Switches, page 435 • ZoneDefense Operation, page 436 12.1. Overview ZoneDefense Controls Switches ZoneDefense allows a NetDefend Firewall to control locally attached switches. It can be used as a counter-measure to stop a virus-in ...

  • D-Link DFL-2560G - page 435

    12.2. ZoneDefense Switches Switch information regarding every switch that is to be controlled by the firewall has to be manually specified in the firewall configuration. The information needed in order to control a switch includes: • The IP address of the management interface of the switch • The switch model type • The SNMP community string ( ...

  • D-Link DFL-2560G - page 436

    12.3. ZoneDefense Operation 12.3.1. SNMP Simple Network Management Protocol (SNMP) is an application layer protocol for complex network management. SNMP allows the managers and managed devices in a network to communicate with each other. SNMP Managers A typical managing device, such as a NetDefend Firewall, uses the SNMP protocol to monitor and con ...

  • D-Link DFL-2560G - page 437

    As a complement to threshold rules, it is also possible to manually define hosts and networks that are to be statically blocked or excluded. Manually blocked hosts and networks can be blocked by default or based on a schedule. It is also possible to specify which protocols and protocol port numbers are to be blocked. Exclude Lists can be created an ...

  • D-Link DFL-2560G - page 438

    2. For Addresses choose the object name of the firewall's interface address 192.168.1.1 from the Available list and put it into the Selected list. 3. Click OK Configure an HTTP threshold of 10 connections/second: 1. Go to Traffic Management > Threshold Rules > Add > Threshold Rule 2. For the Threshold Rule enter: • Name: HTTP-Thresh ...

  • D-Link DFL-2560G - page 439

    of latency time to implement blocking once the rule is triggered. Some models can activate blocking in less than a second while some models may require a minute or more. A second difference is the maximum number of rules supported by different switches. Some switches support a maximum of 50 rules while others support up to 800 (usually, in order to ...

  • D-Link DFL-2560G - page 440

    12.3.5. Limitations Chapter 12. ZoneDefense 440 ...

  • D-Link DFL-2560G - page 441

    Chapter 13. Advanced Settings This chapter describes the configurable advanced settings for NetDefendOS. The settings are divided up into the following categories: Note: Activating changes After any advanced setting is changed, the new NetDefendOS configuration must be deployed in order for the new value to take effect. • IP Level Settings, page ...

  • D-Link DFL-2560G - page 442

    Block 0.0.0.0 as source address. Default: Drop Block 0 Net Block 0.* as source addresses. Default: DropLog Block 127 Net Block 127.* as source addresses. Default: DropLog Block Multicast Src Block multicast both source addresses (224.0.0.0 - 255.255.255.255). Default: DropLog TTL Min The minimum TTL value accepted on receipt. Default: 3 TTL on Low ...

  • D-Link DFL-2560G - page 443

    SecuRemoteUDP Compatibility Allow IP data to contain eight bytes more than the UDP total length field specifies. Checkpoint SecuRemote violates NAT-T drafts. Default: Disabled IP Option Sizes Verifies the size of "IP options". These options are small blocks of information that may be added to the end of each IP header. This function check ...

  • D-Link DFL-2560G - page 444

    IP Reserved Flag Indicates what NetDefendOS will do if there is data in the "reserved" fields of IP headers. In normal circumstances, these fields should read 0. Used by OS Fingerprinting. Default: DropLog Strip DontFragment Strip the Don’t Fragment flag for packets equal to or smaller than the size specified by this setting. Default: 6 ...

  • D-Link DFL-2560G - page 445

    13.2. TCP Level Settings TCP Option Sizes Verifies the size of TCP options. This function acts in the same way as IPOptionSizes described above. Default: ValidateLogBad TCP MSS Min Determines the minimum permissible size of the TCP MSS. Packets containing maximum segment sizes below this limit are handled according to the next setting. Default: 100 ...

  • D-Link DFL-2560G - page 446

    TCP Auto Clamping Automatically clamp TCP MSS according to MTU of involved interfaces, in addition to TCPMSSMax. Default: Enabled TCP Zero Unused ACK Determines whether NetDefendOS should set the ACK sequence number field in TCP packets to zero if it is not used. Some operating systems reveal sequence number information this way, which can make it ...

  • D-Link DFL-2560G - page 447

    initially intended to be used in negotiating for the use of better checksums in TCP. However, these are not understood by any today's standard systems. As NetDefendOS cannot understand checksum algorithms other than the standard algorithm, these options can never be accepted. The ALTCHKREQ option is normally never seen on modern networks. Defa ...

  • D-Link DFL-2560G - page 448

    TCP SYN/FIN The TCP FIN flag together with SYN; normally invalid (strip=strip FIN). Default: DropLog TCP FIN/URG Specifies how NetDefendOS will deal with TCP packets with both FIN (Finish, close connection) and URG flags turned on. This should normally never occur, as you do not usually attempt to close a connection at the same time as sending &quo ...

  • D-Link DFL-2560G - page 449

    TCP sequence number validation is only possible on connections tracked by the state-engine (not on packets forwarded using a FwdFast rule). Possible values are: Ignore - Do not validate. Means that sequence number validation is completely turned off. ValidateSilent - Validate and pass on. ValidateLogBad - Validate and pass on, log if bad. ValidateR ...

  • D-Link DFL-2560G - page 450

    13.3. ICMP Level Settings ICMP Sends Per Sec Limit Specifies the maximum number of ICMP messages NetDefendOS may generate per second. This includes ping replies, destination unreachable messages and also TCP RST packets. In other words, this setting limits how many Rejects per second may be generated by the Reject rules in the Rules section. Defaul ...

  • D-Link DFL-2560G - page 451

    13.4. State Settings Connection Replace Allows new additions to the NetDefendOS connection list to replace the oldest connections if there is no available space. Default: ReplaceLog Log Open Fails In some instances where the Rules section determines that a packet should be allowed through, the stateful inspection mechanism may subsequently decide t ...

  • D-Link DFL-2560G - page 452

    Default: Log Log Connection Usage This generates a log message for every packet that passes through a connection that is set up in the NetDefendOS state-engine. Traffic whose destination is the NetDefend Firewall itself, for example NetDefendOS management traffic, is not subject to this setting. The log message includes port, service, source/destin ...

  • D-Link DFL-2560G - page 453

    13.5. Connection Timeout Settings The settings in this section specify how long a connection can remain idle, that is to say with no data being sent through it, before it is automatically closed. Please note that each connection has two timeout values: one for each direction. A connection is closed if either of the two values reaches 0. TCP SYN Idl ...

  • D-Link DFL-2560G - page 454

    Other Idle Lifetime Specifies in seconds how long connections using an unknown protocol can remain idle before it is closed. Default: 130 13.5. Connection Timeout Settings Chapter 13. Advanced Settings 454 ...

  • D-Link DFL-2560G - page 455

    13.6. Length Limit Settings This section contains information about the size limits imposed on the protocols directly under IP level, such as TCP, UDP and ICMP. The values specified here concern the IP data contained in packets. In the case of Ethernet, a single packet can contain up to 1480 bytes of IP data without fragmentation. In addition to th ...

  • D-Link DFL-2560G - page 456

    Specifies in bytes the maximum size of an AH packet. AH, Authentication Header, is used by IPsec where only authentication is applied. This value should be set at the size of the largest packet allowed to pass through the VPN connections, regardless of its original protocol, plus approx. 50 bytes. Default: 2000 Max SKIP Length Specifies in bytes th ...

  • D-Link DFL-2560G - page 457

    13.7. Fragmentation Settings IP is able to transport up to 65536 bytes of data. However, most media, such as Ethernet, cannot carry such huge packets. To compensate, the IP stack fragments the data to be sent into separate packets, each one given their own IP header and information that will help the recipient reassemble the original packet correct ...

  • D-Link DFL-2560G - page 458

    Default: Check8 – compare 8 random locations, a total of 32 bytes Failed Fragment Reassembly Reassemblies may fail due to one of the following causes: • Some of the fragments did not arrive within the time stipulated by the ReassTimeout or ReassTimeLimit settings. This may mean that one or more fragments were lost on their way across the Intern ...

  • D-Link DFL-2560G - page 459

    • NoLog - No logging is carried out under normal circumstances. • LogSuspect - Logs duplicated fragments if the reassembly procedure has been affected by "suspect" fragments. • LogAll - Always logs duplicated fragments. Default: LogSuspect Fragmented ICMP Other than ICMP ECHO (Ping), ICMP messages should not normally be fragmented a ...

  • D-Link DFL-2560G - page 460

    Reassembly Illegal Limit Once a whole packet has been marked as illegal, NetDefendOS is able to retain this in memory for this number of seconds in order to prevent further fragments of that packet from arriving. Default: 60 13.7. Fragmentation Settings Chapter 13. Advanced Settings 460 ...

  • D-Link DFL-2560G - page 461

    13.8. Local Fragment Reassembly Settings Max Concurrent Maximum number of concurrent local reassemblies. Default: 256 Max Size Maximum size of a locally reassembled packet. Default: 10000 Large Buffers Number of large ( over 2K) local reassembly buffers (of the above size). Default: 32 13.8. Local Fragment Reassembly Settings Chapter 13. Advanced S ...

  • D-Link DFL-2560G - page 462

    13.9. Miscellaneous Settings UDP Source Port 0 How to treat UDP packets with source port 0. Default: DropLog Port 0 How to treat TCP/UDP packets with destination port 0 and TCP packets with source port 0. Default: DropLog Watchdog Time Number of non-responsive seconds before watchdog is triggered (0=disable). Default: 180 Flood Reboot Time As a fin ...

  • D-Link DFL-2560G - page 463

    13.9. Miscellaneous Settings Chapter 13. Advanced Settings 463 ...

  • D-Link DFL-2560G - page 464

    Appendix A. Subscribing to Security Updates Introduction The NetDefendOS Anti-Virus (AV) module, the Intrusion Detection and Prevention (IDP) module and the Dynamic Web Content Filtering module all function using external D-Link databases which contain details of the latest viruses, security threats and URL categorization. These databases are const ...

  • D-Link DFL-2560G - page 465

    An Anti-Virus update can similarly be initiated with the command: gw-world:/> updatecenter -update Antivirus Querying Update Status To get the status of IDP updates use the command: gw-world:/> updatecenter -status IDP To get the status of AV updates: gw-world:/> updatecenter -status Antivirus Querying Server Status To get the status of th ...

  • D-Link DFL-2560G - page 466

    Appendix B. IDP Signature Groups For IDP scanning, the following signature groups are available for selection. These groups are available only for the D-Link Advanced IDP Service. There is a version of each group under the three Types of IDS , IPS and Policy . For further information see Section 6.5, “Intrusion Detection and Prevention” . Group ...

  • D-Link DFL-2560G - page 467

    Group Name Intrusion Type FTP_FORMATSTRING Format string attack FTP_GENERAL FTP protocol and implementation FTP_LOGIN Login attacks FTP_OVERFLOW FTP buffer overflow GAME_BOMBERCLONE Bomberclone game GAME_GENERAL Generic game servers/clients GAME_UNREAL UnReal Game server HTTP_APACHE Apache httpd HTTP_BADBLUE Badblue web server HTTP_CGI HTTP CGI HTT ...

  • D-Link DFL-2560G - page 468

    Group Name Intrusion Type POP3_DOS Denial of Service for POP POP3_GENERAL Post Office Protocol v3 POP3_LOGIN-ATTACKS Password guessing and related login attack POP3_OVERFLOW POP3 server overflow POP3_REQUEST-ERRORS Request Error PORTMAPPER_GENERAL PortMapper PRINT_GENERAL LP printing server: LPR LPD PRINT_OVERFLOW Overflow of LPR/LPD protocol/imple ...

  • D-Link DFL-2560G - page 469

    Group Name Intrusion Type TFTP_OPERATION Operation Attack TFTP_OVERFLOW TFTP buffer overflow attack TFTP_REPLY TFTP Reply attack TFTP_REQUEST TFTP request attack TROJAN_GENERAL Trojan UDP_GENERAL General UDP UDP_POPUP Pop-up window for MS Windows UPNP_GENERAL UPNP VERSION_CVS CVS VERSION_SVN Subversion VIRUS_GENERAL Virus VOIP_GENERAL VoIP protocol ...

  • D-Link DFL-2560G - page 470

    Appendix C. Verified MIME filetypes Some NetDefendOS Application Layer Gateways (ALGs) have the optional ability to verify that the contents of a downloaded file matches the type that the filetype in the filename indicates. The filetypes for which MIME verification can be done are listed in this appendix and the ALGs to which this applies are: • ...

  • D-Link DFL-2560G - page 471

    Filetype extension Application cpl Windows Control Panel Extension file dbm Database file dcx Graphics Multipage PCX Bitmap file deb Debian Linux Package file djvu DjVu file dll Windows dynamic link library file dpa DPA archive data dvi TeX Device Independent Document eet EET archive egg Allegro datafile elc eMacs Lisp Byte-compiled Source Code emd ...

  • D-Link DFL-2560G - page 472

    Filetype extension Application mpv MPEG-1 Video file Microsoft files Microsoft office files, and other Microsoft files msa Atari MSA archive data niff, nif Navy Interchange file Format Bitmap noa Nancy Video CODEC nsf NES Sound file obj, o Windows object file, linux object file ocx Object Linking and Embedding (OLE) Control Extension ogg Ogg Vorbis ...

  • D-Link DFL-2560G - page 473

    Filetype extension Application tfm TeX font metric data tiff, tif Tagged Image Format file tnef Transport Neutral Encapsulation Format torrent BitTorrent Metainfo file ttf TrueType Font txw Yamaha TX Wave audio files ufa UFA archive data vcf Vcard file viv VivoActive Player Streaming Video file wav Waveform Audio wk Lotus 1-2-3 document wmv Windows ...

  • D-Link DFL-2560G - page 474

    Appendix D. The OSI Framework Overview The Open Systems Interconnection Model defines a framework for inter-computer communications. It categorizes different protocols for a great variety of network applications into seven smaller, more manageable layers. The model describes how data from an application in one computer can be transferred through a ...

  • D-Link DFL-2560G - page 475

    Appendix E. D-Link Worldwide Offices Below is a complete list of D-Link worldwide sales offices. Please check your own country area's local website for further details regarding support of D-Link products as well as contact details for local support. Australia 1 Giffnock Avenue, North Ryde, NSW 2113, Australia. TEL: 61-2-8899-1800, FAX: 61-2-8 ...

  • D-Link DFL-2560G - page 476

    Italy Via Nino Bonnet n. 6/b, 20154 – Milano, Italy. TEL: 39-02-2900-0676, FAX: 39-02-2900-1723. Website: www.dlink.it LatinAmerica Isidora Goyeechea 2934, Ofcina 702, Las Condes, Santiago – Chile. TEL: 56-2-232-3185, FAX: 56-2-232-0923. Website: www.dlink.cl Luxemburg Rue des Colonies 11, B-1000 Brussels, Belgium TEL: +32 (0)2 517 7111, FAX: + ...

  • D-Link DFL-2560G - page 477

    Alphabetical Index A access rules, 201 accounting, 56 interim messages, 58 limitations with NAT, 59 messages, 56 system shutdowns, 59 address book, 73 ethernet addresses in, 75 folders, 77 IP addresses in, 73 address groups, 76 address translation, 292 admin account, 26 changing password for, 35 multiple logins, 26 advanced settings ARP, 103 connec ...

  • D-Link DFL-2560G - page 478

    Block Multicast Src setting, 442 boot menu (see console boot menu) BOOTP, 195 BPDU relaying, 184 Broadcast Enet Sender setting, 186 C CAM Size setting, 185 CAM To L3 Cache Dest Learning setting, 184 CA servers access, 383 client access, 384 FQDN resolution, 385 certificates, 114 CA authority, 114 certificate requests, 116 identification lists, 355 ...

  • D-Link DFL-2560G - page 479

    Dynamic L3C Size setting, 185 Dynamic Max Connections setting, 452 dynamic routing policy, 159 DynDNS service, 125 E Enable Sensors setting, 61 end of life procedures, 71 ESMTP extensions, 217 ethernet interface, 85 changing IP addresses, 86 CLI command summary, 88 default gateway, 87 IP address, 86 with DHCP, 87 evasion attack prevention, 277 even ...

  • D-Link DFL-2560G - page 480

    Illegal Fragments setting, 457 Initial Silence (HA) setting, 432 insertion attack prevention, 277 Interface Alias (SNMP) setting, 65 Interface Description (SNMP) setting, 65 interfaces, 84 disabling, 85 groups, 98 loopback, 84, 85 physical, 84 internet key exchange (see IKE) Interval between synchronization setting, 123 intrusion, detection and pre ...

  • D-Link DFL-2560G - page 481

    Max TCP Length setting, 455 Max time drift setting, 123 Max Transactions (DHCP) setting, 196 Max UDP Length setting, 455 memlog, 52 MIME filetype verification in FTP ALG, 209 in HTTP ALG, 206 in POP3 ALG, 224 in SMTP ALG, 215 list of filetypes, 470 Min Broadcast TTL setting, 444 Minimum Fragment Length setting, 459 multicast address translation, 16 ...

  • D-Link DFL-2560G - page 482

    static, 129 the all-nets route, 135 S SA (see security association) SafeStream, 270 SAT, 300 IP rules, 109 multiplex rule, 162 port forwarding, 300 second rule destination, 300 schedules, 112 SCP, 41 scripting (see CLI scripts) Secondary Time Server setting, 123 secure copy (see SCP) SecuRemoteUDP Compatibility setting, 442 secure shell (see SSH) s ...

  • D-Link DFL-2560G - page 483

    in zonedefense, 436 time synchronization, 119 Time Sync Server Type setting, 123 Time Zone setting, 122 TLS ALG, 248 traffic shaping, 390 bandwidth guarantees, 398 bandwidth limiting, 393 FwdFast IP rule exclusion, 392 groups, 399 objectives, 390 precedences, 396 recommendations, 400 summary, 402 with IDP, 407 Transaction Timeout (DHCP) setting, 19 ...

Manufacturer D-Link Category Hardware firewall

Documents that we receive from a manufacturer of a D-Link DFL-2560G can be divided into several groups. They are, among others:
- D-Link technical drawings
- DFL-2560G manuals
- D-Link product data sheets
- information booklets
- or energy labels D-Link DFL-2560G
All of them are important, but the most important information from the point of view of use of the device are in the user manual D-Link DFL-2560G.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals D-Link DFL-2560G, service manual, brief instructions and user manuals D-Link DFL-2560G. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product D-Link DFL-2560G.

Similar manuals

A complete manual for the device D-Link DFL-2560G, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use D-Link DFL-2560G by users. Manuals are usually written by a technical writer, but in a language understandable to all users of D-Link DFL-2560G.

A complete D-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual D-Link DFL-2560G - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the D-Link DFL-2560G, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the D-Link DFL-2560G, that we can find in the current document
3. Tips how to use the basic functions of the device D-Link DFL-2560G - which should help us in our first steps of using D-Link DFL-2560G
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with D-Link DFL-2560G
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of D-Link DFL-2560G in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning D-Link DFL-2560G?

Use the form below

If you did not solve your problem by using a manual D-Link DFL-2560G, ask a question using the form below. If a user had a similar problem with D-Link DFL-2560G it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)