Manual Eaton TRS 3064

13 pages 1.4 mb
Download

Go to site of 13

Summary
  • Eaton TRS 3064 - page 1

    TRS 3064 Installation, Operation and Maintenance of the Airflex@ Timing Rotorseal and Cam Limit Switch Revised: Feb. 1, 1982 ...

  • Eaton TRS 3064 - page 2

    1.0 Operation Throughout this manual, there are a number of Hazard Warnings that must be read and understood in order to prevent possible personal injury and/or damage to the equipment. Carefully read these warn- ings. They are included to protect you! 1.1 Description: This manual describes two Airflex@ timing control devices, namely, the Airflex@ ...

  • Eaton TRS 3064 - page 3

    Figure 1 illustrates the cams assembled in the timing section of both devices and their relationships. 1 Cam No. 2 Cam Insert No. 3 Cam No. 4 Cam insert No. Cams for Clockwise Rotation Cams for Counterclockwise Rotation Figure 1. Cam profiles and their relationships 3 ...

  • Eaton TRS 3064 - page 4

    Cam No. 3 (28 and 28A) monitors the effective- ness of the press braking system at the top of the stroke. When cam No. 3 is positioned according to Paragraph 2.3, deviations in stopping position greater than + 15” from top dead center will be detected. 2.0 Installation n ! Danger: Prior to installation of the Airflex’“’ Timing Rotorseal and ...

  • Eaton TRS 3064 - page 5

    2.1.2. To a) b) c) d) e) f) g) h) i) j) mount the timing rotorseal: Make sure that the air tube “O” rings (2) are in place. Install the plastic insert (37A) in the head of the drive screw (37). Install drive screw. Tighten the screw, being careful not to distort the end plate (36). Tie-wire the drive screw to the end plate mounting screws. Alig ...

  • Eaton TRS 3064 - page 6

    Before mounting the timer, check to be sure its direction of rotation corresponds to that of the shaft. Fasten the flange to the shaft with lockwashers and cap screws. Refer to appropriate paragraph and mount second timer. W iring instructions are given in Paragraph 2.2. 2.2 Wiring: Two rotary timers are required in the Airflex@ press control syste ...

  • Eaton TRS 3064 - page 7

    m) Retighten the jam nuts (30) and repeat Steps “f”, “g” and “h”. n) Repeat this procedure as necessary to ob- tain the desired stopping position. 2.3.2 Long Operation: This feature is provided so an adjustment can be made to extend the LS4 open time and accommodate presses with long strokes and/or slow crankshaft speeds. a) b) c) d) e) ...

  • Eaton TRS 3064 - page 8

    Breaker Point Opening Gap: This gap is preset at the factory on new units at time of assembly. A gap setting of .040” to .050” must be maintained at all times. The opening gap must be checked regularly and reset when required. To inspect for proper opening gap: a) b) c) d) e) h) i) j) k) Position the crankshaft at top dead center. Use die safet ...

  • Eaton TRS 3064 - page 9

    o) P) q) r) s) t) u) v) w) Align No. 5 cam with previously establish- ed top stop mark by rotating cam adjusting knob. Maintain No. 5 cam alignment by holding adjusting knob. Rotate No. 3 cam so that indicator groove lines up with the fiber cam follower on LS3 breaker point. Refer to Figure 4. This alignment must be done with the crankshaft at top ...

  • Eaton TRS 3064 - page 10

    ...

  • Eaton TRS 3064 - page 11

    Item No. - 6. 20. 22. 23. 24. 25. 26. 27. 28. 28A 29. 30. 31. 32. 33. 33A 34 38. 40. 41. 42. 45. 46. 47. Part No. Description 302276 159 x 41 139 x 12 See table C See table C 201854 See table C 201869 See table C 306030 203003 61 x 22 412230 409346 See table C See table C 119 x 23 507137 153 x 530 203107 404583 411367 405330 203351 Shaft Bearing Sn ...

  • Eaton TRS 3064 - page 12

    FOOT MOUNTED CAM LIMIT SWITCH Part No. for Optional Cam No. 3 (Item No. 28A), is as follows: 203002 (For clockwise and clockwise 30” dwell) 203087 (for c’clockwise and c’clockwise 30” dwell) Eaton Corporation Airflex Division Cleveland, Ohio 44144 PWNTED IN u. 5. A. ...

  • Eaton TRS 3064 - page 13

    PDF form at Form ML-31 8 Revised September 3, 1997 Eaton Cor poration Airflex Division 9919 Clinton Road Cleveland, Ohio 44144 Printed in U.S.A. EAT ON PROD UCT WARR ANTY Subject to t he c ondit io ns st ated herei n, Eaton C orpo rati on w arran ts to the Pur chaser that e ach ne w Air fl ex Produ ct manufa ctured by Eaton will be free from fai lu ...

Manufacturer Eaton Category Switch

Documents that we receive from a manufacturer of a Eaton TRS 3064 can be divided into several groups. They are, among others:
- Eaton technical drawings
- TRS 3064 manuals
- Eaton product data sheets
- information booklets
- or energy labels Eaton TRS 3064
All of them are important, but the most important information from the point of view of use of the device are in the user manual Eaton TRS 3064.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Eaton TRS 3064, service manual, brief instructions and user manuals Eaton TRS 3064. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Eaton TRS 3064.

Similar manuals

A complete manual for the device Eaton TRS 3064, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Eaton TRS 3064 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Eaton TRS 3064.

A complete Eaton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Eaton TRS 3064 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Eaton TRS 3064, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Eaton TRS 3064, that we can find in the current document
3. Tips how to use the basic functions of the device Eaton TRS 3064 - which should help us in our first steps of using Eaton TRS 3064
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Eaton TRS 3064
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Eaton TRS 3064 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Eaton TRS 3064?

Use the form below

If you did not solve your problem by using a manual Eaton TRS 3064, ask a question using the form below. If a user had a similar problem with Eaton TRS 3064 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)