Manual Delta 36-978

37 pages 2.08 mb
Download

Go to site of 37

Summary
  • Delta 36-978 - page 1

    INSTRUCTION MANUAL 10" Contractor’ s Saw (Models 36-978, 36-979) P ART NO. A13253 - 09-15-05 Rev . B Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). MODEL 36 ...

  • Delta 36-978 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 36-978 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially haz ard ous situation which, if not avoided, may result in minor or mod er ate injury . Used without the ...

  • Delta 36-978 - page 4

    4 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Lear ning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE AND HEARING PROTECTION. AL WA YS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SA ...

  • Delta 36-978 - page 5

    5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or anothe ...

  • Delta 36-978 - page 6

    6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3-prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connect ...

  • Delta 36-978 - page 7

    7 Fig. C GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES EXTENSION CORDS USE PROPER EXTENSION CORDS. MAKE SURE YOUR EXTENSION CORD IS IN GOOD CONDITION AND IS A 3-WIRE EXTENSION CORD WHICH HAS A 3-PRONG GROUNDING TYPE PLUG AND MA TCHING RECEPT ACLE WHICH WILL ACCEPT THE MACHINE’S PLUG. WHEN USING AN EXTENSI ...

  • Delta 36-978 - page 8

    8 Delta Models 36-978 and 36-979 are left-tilting 10" contractor saws with a built-in mobility kit. The saws have a powerful 1½ HP induction motor which can handle tough cutting operations. The 36-978 comes with sheet metal wings and the 36-979 comes with cast iron wings. A RIP FENCE ASSEMBL Y IS NOT P ACKAGED WITH THE PRODUCT . YOU MUST INST ...

  • Delta 36-978 - page 9

    9 EXTENSION WINGS Fig. 2 MODEL 36-978 2 SHEET MET AL EXTENSION WINGS MODEL 36-979 2 CAST IRON EXTENSION WINGS ST AND AND MOBILE BASE P ARTS 24. Plastic Foot (4) 25. Corner Bracket (left side) 26. Corner Bracket (right side) 27. Wheel (2) 28. Short Side Leg Support (2) 29. Long Side Leg Support (2) Fig. 3 24 27 33 25 26 28 29 30 31 32 30. Leg (4) 31 ...

  • Delta 36-978 - page 10

    10 HARDW ARE 1. 7 / 16 -20 x 3 / 4 " Hex Head Screw (6) (For Sheet Metal) 2. 7 / 16 -20 x 1 1 / 4 " Hex Head Screw (6) (For Cast Iron) 3. 3 / 8 -16 x 1 1 / 2 " Flat Head Screw (1) 4. 5 / 16 -18 x 3 / 4 " Carriage Head Screw (12) 5. 5 / 16 -18 x 5 / 8 " Carriage Head Screw (42) 6. 1 / 4 -20 x 1 1 / 2 " Hex Head Screw (1 ...

  • Delta 36-978 - page 11

    MOBILE BASE AND ST AND ASSEMBL Y FOR YOUR OWN SAFETY , DO NOT CONNECT MACHINE TO POWER SOURCE UNTIL MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE INSTRUCTION MANUAL. The mobile base and stand should be put together upside down to ease assembly . T o assemble the mobile base and stand: FRONT AND SIDE P ANELS 1. Insert a 5 / 16 -1 ...

  • Delta 36-978 - page 12

    9. Repeat for other similar cor ner bracket. These brackets, (G) Fig. 13 are wher e the rubber leveling feet will be installed. 10. The brackets with the open end, as shown at (M) Fig. 14, are attached in a similar manner as described in Steps 6 to 9. NOTE: MAKE SURE THE OPEN END IS ALIGNED AS SHOWN IN FIGS. 14 AND 15. THE WHEELS WILL BE INST ALL E ...

  • Delta 36-978 - page 13

    T o install the dust chute and back brace, place the saw unit upside down on the floor as shown in Fig. 25. PROTECT THE SAW’S T ABLE TOP BY PLACING SOMETHING BETWEEN THE SAW AND THE FLOOR, SUCH AS A PIECE OF CARDBOARD, CARPET ETC. T o install dust chute (A) Fig. 25, slide it in as shown. Place back brace (B) with tabs (C) Fig. 25 below the chute ...

  • Delta 36-978 - page 14

    14 BLADE TIL TING AND RAISING HANDWHEEL 1. Place blade tilting handwheel (A) Fig. 29, onto shaft (B). Make certain slot (C) in handwheel is engaged with roll pin (D) on the shaft. 2. Place a 10mm Nylon Flat W asher (E) onto shaft (B) and then thread locking knob (F), onto the shaft. 3. Assemble the blade raising handwheel (G) Fig. 30, to the front ...

  • Delta 36-978 - page 15

    MOTOR AND MOTOR MOUNTING PLA TE TO SA W 1. Insert the tapered end of pin (G) Fig. 32, into the inside holes in each side of bracket (H). 3. Assemble spring (I) Fig. 32, onto the non-tapered end of each pin (G) as shown. 4. Position motor and motor mounting plate (A) Fig. 33, below bracket (B) to allow bracket arm to slide through lar ge opening (C) ...

  • Delta 36-978 - page 16

    16 3. Slide the belt and pulley guard bracket (I) Fig. 36, between the motor plate (J) and motor mounting plate (K), as shown. 5. Position belt and pulley guard bracket (I) Fig. 37, so the motor pulley (K) is centered and thr ough the hole in the belt and pulley guard bracket (I), as shown in Fig. 37. Tighten the four hex nuts (C) Fig. 31 that fast ...

  • Delta 36-978 - page 17

    17 9. Place a ¼" flat washer and then a spacer (P) onto the ¼-20x1-1/2" hex head screw (L) Fig. 37. Then thread a ¼-20 Hex Nut (Q) Fig. 37, onto the scr ew post until it tightens the spacer onto the pulley guard (I) Fig. 37. 10. Align the hole (S) Fig. 40 in the belt guard (R) with the ¼-20x1 ½" hex head screw (L) Fig. 37. Place ...

  • Delta 36-978 - page 18

    X Y Z 18 BLADE GUARD AND SPLITTER ASSEMBL Y AND ALIGNMENT 1. Fasten the r ear splitter mounting bracket (A) Fig. 43, to the rear trunnion. Align the two holes in the rear splitter mounting bracket (shown at B) with the two holes in the trunnion. Place a ¼" Lock W asher onto a ¼ -20 x ¾" Hex Head Screw , place a ¼" Flat W asher on ...

  • Delta 36-978 - page 19

    19 7. Assemble the blade guard and splitter assembly (G) Fig. 47, between the lar ge washer (C) and the splitter bracket and tighten screw (H) with wr ench supplied. Slide splitter as far down as it will go. 8. Fasten the rear of the blade guard and splitter bracket assembly (G) Fig. 48, to the rear splitter mounting bracket. Align the hole (J) in ...

  • Delta 36-978 - page 20

    20 10. Using a straight edge, check to see if the rear of the splitter (G) is aligned with the saw blade, as shown in Fig. 51. If alignment is necessary , loosen the screws (B) Fig. 43, align splitter (G) with the saw blade, and tighten two screws (B) Fig. 43. 11. Lower saw blade and install table insert (P) Fig. 52, in the saw table as shown. THE ...

  • Delta 36-978 - page 21

    ON/OFF SWITCH Insert a 3/8-16x 1½" Flat Head Screw (F) Fig. 54, through hole (B) in the fr ont the saw table and then through the hole (E) in the switch bracket. Place a 3/8" Flat W asher (G), then a 3/8" Lockwasher (H), onto the screw (F). Then thr ead a 3/8-16 Hex Nut (J) onto the screw and tighten secur ely . Fig. 54 F B E G J H ...

  • Delta 36-978 - page 22

    RAISING AND LOWERING BLADE T o raise the saw blade, loosen lock knob (C) Fig. 59, and turn the blade raising handwheel (D) clockwise. When the blade is at the desired height, tighten lock knob (C). T o lower the blade, loosen lock knob (C) and tur n the handwheel (D) counterclockwise. NOTE: One full tur n of the handwheel will change blade height a ...

  • Delta 36-978 - page 23

    23 Fig. 63 Fig. 64 A B C D E ASSEMBLING MITER GAUGE Place a flat washer (A) Fig. 62 on the threads of the miter gauge lock handle (B) and then thread the handle into the hole (C) in miter gauge bar . Insert washer ( D) Fig. 64 into the miter gage slot (E) and slide miter gauge onto saw table. MITER GAUGE OPERA TION AND ADJUSTMENT The miter gauge is ...

  • Delta 36-978 - page 24

    24 ALIGNING MITER SLOTS TO BLADE The saw table has been aligned at the factory so the miter gauge slots are parallel to the saw blade. However , it is recommended to check the alignment befor e initial operation as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Place a combination square (A) Fig. 66, on the table with one edge of the square in t ...

  • Delta 36-978 - page 25

    25 BACKLASH ADJUSTMENTS FOR BLADE RAISING AND BLADE TIL TING MECHANISMS If any play is detected in the blade raising or blade tilting mechanisms, the following adjustments should be made. DISCONNECT MACHINE FROM POWER SOURCE. NOTE: The machine has been turned upside down and the blade removed for clarity and safety . 1. Adjusting blade raising mech ...

  • Delta 36-978 - page 26

    26 KEY P AR TS AND SAFETY FEA TURES ON YOUR SAW 1 2 2 3 4 5 6 7 8 8 9 10 13 11 12 18 14 15 17 19 16 BACK VIEW 13. Belt Guard 14. Motor 15. Overload Reset Button 16. Mobile Base 17. Motor Cord 18. Mobile Base Foot Pedal 19. Blade Wr enches 20. Leveling Feet 5a 6a 7a 11a 20 FRONT VIEW 1. T able T op 2. Extension Wings 3. Blade Guard/Splitter/Anti- Ki ...

  • Delta 36-978 - page 27

    27 CROSS-CUTTING Cross-cutting r equires the use of the miter gauge to posi- tion and guide the work. Before starting the cut, raise the blade so it is about 1/8” (3.2mm) higher than the top of the workpiece. Place the work against the miter gauge and advance both the gauge and work toward the saw blade, as shown in Fig. S2. The miter gauge may b ...

  • Delta 36-978 - page 28

    NEVER USE THE FENCE AS A CUT -OFF GAUGE WHEN CROSS-CUTTING. When cross-cutting a number of pieces to the same length, a block of wood (B), can be clamped to the fence and used as a cut-off gauge as shown in Fig. S4. The block (B) must be at least 3/4-inch thick to prevent the cut-off piece fr om binding between the blade and the fence during remova ...

  • Delta 36-978 - page 29

    29 Fig. S8 Fig. S9 A Fig. S10 Ripping, as shown in Fig. S8, is cutting lengthwise through a boar d. The rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. THE SAW BLADE GUARD MUST BE USED. ON DEL T A SAWS, THE GUARD HAS ANTI-KICKBACK P A WLS TO ...

  • Delta 36-978 - page 30

    30 BEVEL RIPPING Bevel ripping (as shown in Fig. S12) is the same as ripping except the bevel angle is set to an angle other than 0 degrees. WHEN POSSIBLE, PLACE THE FENCE ON THE RIGHT SIDE OF THE BLADE SO THA T THE BLADE IS TIL TED AWA Y FROM THE FENCE AND HANDS. KEEP HANDS CLEAR OF THE BLADE AND USE A PUSHSTICK TO FEED THE WORKPIECE IF THERE IS L ...

  • Delta 36-978 - page 31

    31 Fig. S15 NOTE: THE OUTSIDE ARBOR FLANGE CAN NOT BE USED WITH THE MOULDING CUTTERHEAD. TIGHTEN THE ARBOR NUT AGAINST THE CUTTERHEAD BODY . DO NOT LOSE THE OUTSIDE ARBOR FLANGE. IT WILL BE NEEDED WHEN REA TT ACHING A BLADE TO THE ARBOR. AL WA YS RETURN AND F ASTEN THE BLADE GUARD AND SPLITTER ASSEMBL Y TO ITS PROPER OPERA TING POSITION FOR NORMAL ...

  • Delta 36-978 - page 32

    32 Fig. S20 Fig. S18 Fig. S19 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. S17). V arious combinations of saws and cutters are used to cut grooves fr om 1/8 ″ to 13/16 ″ for use in shelving, making joints, tenoning, grooving, etc. The cutt ...

  • Delta 36-978 - page 33

    33 CONSTRUCTING A FEA THERBOARD Fig. S23, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should be a straight piece of wood that is free of knots and cracks. Featherboar ds are used to keep the work in contact with the fence and table, as shown in Fig. S24, and help prevent kickback ...

  • Delta 36-978 - page 34

    34 WHEN RIPPING WORK LESS THAN 6 INCHES WIDE, A PUSH STICK SHOULD BE USED TO COMPLETE THE FEED AND COULD EASIL Y BE MADE FROM SCRAP MA TERIAL BY FOLLOWING THE P A TTERN SHOWN IN FIG. S25. Fig. S25 PUSH STICK MAKE FROM 1/2 " OR 3/4 " WOOD OR THICKNESS LESS THAN WIDTH OF MA TERIAL TO BE CUT CUT OFF HERE TO PUSH 1/4 " WOOD CUT OFF HERE ...

  • Delta 36-978 - page 35

    35 If you desire to make a shelf for your saw , use the diagram below for the size of plywood and placement of holes. Be sure to attach the shelf to the stand and mobility kit while it is still upside down during the assembly pr ocedure. The shelf, once cut, will be attached by driving wood screws thr ough the holes in the overhang of the leg suppo ...

  • Delta 36-978 - page 36

    36 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized ser ...

  • Delta 36-978 - page 37

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Manufacturer Delta Category Dust Collector

Documents that we receive from a manufacturer of a Delta 36-978 can be divided into several groups. They are, among others:
- Delta technical drawings
- 36-978 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta 36-978
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta 36-978.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta 36-978, service manual, brief instructions and user manuals Delta 36-978. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta 36-978.

Similar manuals

A complete manual for the device Delta 36-978, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta 36-978 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta 36-978.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta 36-978 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta 36-978, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta 36-978, that we can find in the current document
3. Tips how to use the basic functions of the device Delta 36-978 - which should help us in our first steps of using Delta 36-978
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta 36-978
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta 36-978 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta 36-978?

Use the form below

If you did not solve your problem by using a manual Delta 36-978, ask a question using the form below. If a user had a similar problem with Delta 36-978 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)