Manual Craftsman PROFESSIONAL 315.273731

80 pages 15.47 mb
Download

Go to site of 80

Summary
  • Craftsman PROFESSIONAL 315.273731 - page 1

    Owner's Manual 254 mm (10 in.) Stationary RADIAL ARM SAW Stock No. 927373 Model No. 315.273731 Save this manual for future reference. ,A CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-877-369-8665 Sold by: Sears Canada Inc., Toronto M5B 2B8 Visit the Craftsman web pa ...

  • Craftsman PROFESSIONAL 315.273731 - page 2

    FULL TWO YEAR WARRANTY ON CRAFTSMAN TOOL If this CRRFTSMRN Tool fails to operate within two years from the date of purchase, return it to the nearest Sears Canada Inc. ("Sears") store and "Sears" will repair it, free of charge. If this tool is used for rental purposes, this warranty applies for only 90 days from the date of purc ...

  • Craftsman PROFESSIONAL 315.273731 - page 3

    Installing the Yoke Assembly ......................................................................................................................... 22 Removing the Blade ....................................................................................................................................... 23 Attaching Table Supports ............. ...

  • Craftsman PROFESSIONAL 315.273731 - page 4

    The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBO ...

  • Craftsman PROFESSIONAL 315.273731 - page 5

    • USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or les ...

  • Craftsman PROFESSIONAL 315.273731 - page 6

    • GUARD AGAINST KICKBACK. Kickback can • occur when the blade stalls, driving the work piece back toward the operator. It can cause your hand to contact the blade, resulting in serious personal • injury. Stay out of the bladepath and turn switch off immediately if blade bindsorstalls. • DO NOT USE A PERSON AS A SUBSTITUTE FOR A TABLE if add ...

  • Craftsman PROFESSIONAL 315.273731 - page 7

    • SECURE THE SAW. Firmly bolt the saw to the leg stand to keep the saw from tipping, walking, or sliding. • DO NOT SET UP WORK WITH THE BLADE SPINNING. Keep the saw power off until you are ready to use it. • RIP ONLY WORKPIECES LONGER THAN THE BLADE'S DIAMETER. Never rip a piece of wood that is shorter than the diameter of the blade. • ...

  • Craftsman PROFESSIONAL 315.273731 - page 8

    EXTENSION CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a consider- able distance from the power source, use an exten- sion cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in li ...

  • Craftsman PROFESSIONAL 315.273731 - page 9

    CHANGING VOLTAGE See Figures 2-4. Your radial saw has been set up at the factory to operate efficiently on a 120V AC single voltage circuit. However, if heavy duty operation is required, the circuits are overloaded, or the circuit is low voltage, have a qualified electrician change the voltage on the main power system to a 240V AC voltage circuit. ...

  • Craftsman PROFESSIONAL 315.273731 - page 10

    Blade Arbor Blade Diameter Blade Bevel Angle Radial Arm Swing Range Blade Height Adjust Carriage Travel Cutting Capacity - Maximum Cross Cut Cutting Capacity - Maximum Out-Rip 16 mm (5/8 in.) 254 mm (10 in.) 0 ° _ 90 ° 50 ° left - 90 ° right 5.35 in. 17.25 in. 15.50 in. 26 in. Cutting Capacity- Maximum In-Rip Depth of Cut at 90 ° Depth of Cut ...

  • Craftsman PROFESSIONAL 315.273731 - page 11

    Resin A sticky, sap-based substance. Rip Cut In a radial saw, a cut made with the blade parallel to the fence and perpendicular to the arm. Can be across or with the grain. The teeth point up at the point of contact with the wood. Sawblade Path The area directly in line with the blade -- over, under, behind, or in front of it. Also, the workpiece a ...

  • Craftsman PROFESSIONAL 315.273731 - page 12

    Check all loose parts from the box withthelist below. Use the instructions on the following pages to assemble. All fasteners are shown actual size. 1. Saw Assembly .................................................... 1 SAW ASSEMBLY SHOWN AS PACKED . Elevating Handwheel A. Handwheel ..................................................... 1 B. Screw (1 ...

  • Craftsman PROFESSIONAL 315.273731 - page 13

    Check all loose parts from the box with the list below. Use the instructions on the following pages to assemble. All fasteners are shown actual size. 5. Saw Base To Leg Stand Assembly A. Saw Assembly (not shown) ........................... 1 B. Leg Stand Assembly (not shown) .................. 1 C. Hex bolt (5/16-18 x 5/8 in. Hex Head) ........... ...

  • Craftsman PROFESSIONAL 315.273731 - page 14

    Check all loose parts from the box with the list below. Use the instructions on the following pages to assemble. All fasteners are shown actual size. 12. Table Support A. Table Support Rails ....................................... 2 B. Square head bolt (5/16-18 x 3/4 in.) .............. 4 C. Flat washer (5/16 in.) .................................. ...

  • Craftsman PROFESSIONAL 315.273731 - page 15

    The following tools are needed for assembly and alignment. They are not included with this saw. LEVEL HEX KEYS: 5/32in. AND1/8in. MEDIUM FLAT BLADE SCREWDRIVER #2 PHILLIPS SCREWDRIVER PENCIL CHANNELLOCK PLIERS FRAMING SQUARE PLIERS WRENCHES: 7/16 in., 1/2 in., 9/16 in., 15/16 in. +_ SMALL HAMMER Fig. 7 1 5 rRFtFTSMAN ° RADIAL SAW 315.273731 ...

  • Craftsman PROFESSIONAL 315.273731 - page 16

    KNOW YOUR RADIAL SAW See Figure 8A. OVERVIEW -The main operating components include the column, the arm, and the yoke assembly (yoke, motor, and blade), and their operation is summarized in the paragraph below. Safety features and control functions are given also. Spending a few minutes reviewing the illustrations and features list below and on the ...

  • Craftsman PROFESSIONAL 315.273731 - page 17

    FEATURES LIST See Figures 8A-8D. ADJUSTABLE TABLES - A narrow spacer table and wider rear table that can be repositioned or even replaced with different tables. See Figure 8C. ANTI-KICKBACK PAWLS - Toothed pawls that snag the work in case of kickback during rip cuts. (When the blade is parallel to the arm, the pawls are in front of the blade.) Keep ...

  • Craftsman PROFESSIONAL 315.273731 - page 18

    CARRIAGE - Slides along track under arm and supports yoke. Contained in two carriage covers, one on each side of the arm. See Figure 8C. CARRIAGE LOCK KNOB - Controls whether the carriage is locked or can travel. Located on the left side of the arm on the carriage cover. See Figure 8C. COLUMN - Upright housing at the back of the saw, consisting of ...

  • Craftsman PROFESSIONAL 315.273731 - page 19

    MOTOR (13/6.5 AMP) - Powers the blade and is controlled by the switch and key at the front of the arm. The powerful induction motor has a capacitor start. It is mounted in the yoke and rotated with the bevel index knob and bevel lock lever. See Figure 8B. RIP SCALES - Show the distance from the fence to the blade. (In-rip scales are on the right si ...

  • Craftsman PROFESSIONAL 315.273731 - page 20

    Assembly is best done in the area where the saw will be used. When you remove the saw andhardware from the packing materials, carefully check the items with the Loose Parts list. If you areunsure about the description of any part, refer to their illustrations. For your convenience, allfasteners have been drawn actual size. If anyparts are missing, ...

  • Craftsman PROFESSIONAL 315.273731 - page 21

    MOUNTING SAW TO LEG STAND See Figure 10. ,_ WARNING: Firmly bolt the saw to the leg stand to keep the saw from tipping, walking, or sliding. • Locate the following hardware from a small hard- ware bag: 4 hex bolts (5/16-18 x 5/8 in.) 4 Iockwashers (5/16 in.) 8 flat washers (11/32 in.) 4 hex nuts (5/16-18) • Place the saw on top of the leg stand ...

  • Craftsman PROFESSIONAL 315.273731 - page 22

    INSTALLING THE YOKE ASSEMBLY See Figures 12A - 12C. The yoke rides in the carriage below the arm and supports the motor, the blade guard, and the blade. Install the yoke assembly from the front of the arm. • Remove the carriage stop screw and Iockwasher from below the front of the arm with a 1/4 in. hex key. See Figure 12A. ARM VIEWED FROM BELOW ...

  • Craftsman PROFESSIONAL 315.273731 - page 23

    REMOVING THE BLADE See Figure 13. Remove the blade and blade guard assembly during setup for safety and better access. The blade guard includes an upper blade guard, an outer lower guard, and an inner lower guard. The lower inner guard consists of two overlapping slotted metal strips. The strips are held together with a retaining screw and a nut. L ...

  • Craftsman PROFESSIONAL 315.273731 - page 24

    SETTING THE ARM LOCK KNOB See Figure 15. It may be possible to move the arm when locked, if the arm lock knob is too loose. If the arm does not move freely when unlocked, the arm lock knob may be too tight. Use this procedure to check and set the arm lock knob by turning the arm lock wheel (under the carriage arm). • To release the arm lock knob, ...

  • Craftsman PROFESSIONAL 315.273731 - page 25

    SETTING THE BEVEL LOCK LEVER See Figures 17A -17C. The bevel lock lever locks the blade at desired angles other than the preset positive stop angles. The bevel lock lever is preset at the factory but may need readjustment after shipping or extended use. Check for overtightness or looseness and make any neces- sary adjustments as follows: The bevel ...

  • Craftsman PROFESSIONAL 315.273731 - page 26

    TIGHTENING THE ARM AND COLUMN See Figure 18. There should be no play, vertical or horizontal, in the arm relative to the column. If you can move the arm up, down or sideways when the arm lock knob is unlocked, use the following steps to tighten the arm. Note: The arm should pivot only when the arm lock knob is unlocked and pulled forward to com- pr ...

  • Craftsman PROFESSIONAL 315.273731 - page 27

    • Rotation check: To check the rotation, hold the front of the arm with one hand and grasp the top of the column support with the other. Press the arm to the side. If there is play between the column support and the column tube, it needs to be adjusted. See Figure 19B. COLUMN TUBE r COLUMN SUPPORT Fig. 19B • Elevation Adjustment. If the eleva ...

  • Craftsman PROFESSIONAL 315.273731 - page 28

    ADJUSTING THE CARRIAGE BEARINGS See Figures 20A and 20B. Loose carriage bearings permit the blade to wander slightly while cutting, which will result in a poor cut and more wear and tear on the saw. Use the following steps to check for tightness and to then adjust the bearings if needed. • On the left side of the arm, remove the carriage lock kno ...

  • Craftsman PROFESSIONAL 315.273731 - page 29

    LEVELING THE TABLE SUPPORTS See Figures 2fA and 2fB. The table supports must be perfectly level. • Pull the bevel lock lever forward to unlock it. Use the bevel index knob to rotate the motor so the arbor shaft points down. Lock the bevel lock lever. • Release the arm lock knob to angle the arm. Begin by positioning the arbor shaft over the bac ...

  • Craftsman PROFESSIONAL 315.273731 - page 30

    INSTALLING THE FRONT TABLE See Figures 22A - 22C. Use this procedure to install the fixed front table. The top of the table has counterbored holes, predrilled from the top, around the center to attach the table. In the center are a counterbored hole and a small hole, which is not counterbored. They are used for raising or lowering the center of the ...

  • Craftsman PROFESSIONAL 315.273731 - page 31

    LEVELING THE FRONT TABLE See Figure 23. If there are any high or low areas on the front table, they should be removed by adjusting the leveling screws in the center holes on the front table. • Place the rear table on its edge across the front table to check for gaps. • Adjust gaps of less than 1/32 in. in the center of the table by turning the ...

  • Craftsman PROFESSIONAL 315.273731 - page 32

    THUMBSCREW CLAMP BRACKET SQUARE NUT I CUP WASHER _) RECTANGLE HOLE CUP TO WASHER LOOSEN TO TIGHTEN THUMB SCREW CLAMPSHOWN ASSEMBLED SLOT Fig. 24B TABLE SUPPORT INSTALLING BLADE AND BLADE GUARD See Figures 25A and 25B. • Collect the blade and hardware that were removed earlier. Place the inner blade washer, saw blade, outer blade washer, and blade ...

  • Craftsman PROFESSIONAL 315.273731 - page 33

    ALIGN RIVING KNIFE TO BLADE See Figures 26A - 26C. When ripping the riving knife must be centered with the blade to ride in the middle of the kerf and keep it from binding. Binding pinches the blade. Blade pinching can cause kickback. There are two pairs of anti-kickback pawls. ,_!1 WARNING: Failure to use the riving knife, hold downs, and anti-kic ...

  • Craftsman PROFESSIONAL 315.273731 - page 34

    INSTALLING RIP SCALE INDICATORS See Figure 27. The rip scale indicators on the arm show the distance between the blade and the rip fence with the fence in the front and rear positions. The upper scale is used when the fence is positioned directly behind the front table. The lower scale is used when the fence is at the extreme rear, directly in fron ...

  • Craftsman PROFESSIONAL 315.273731 - page 35

    ALIGNING THE ARM FOR CROSS CUTS See Figures 28A - 28C. This procedure checks whether the arm is exactly 0 ° for cross cut travel by checking the blade against the table and the miter indicator. Remove the rear table, spacer table, and fence, but leave the front table in place. You will need a framing square, a 3/16 in. hex key, and a pencil. ,_ WA ...

  • Craftsman PROFESSIONAL 315.273731 - page 36

    ALIGNING BLADE TO TABLE AT 0 ° BEVEL See Figures 29A - 29D. This procedure squares the blade to the table at 0 ° bevel (vertical) so the blade angle will be accurate. If the blade is not at 0 ° bevel, follow the steps below to rotate slightly. You will need a framing square and a 1/4 in. hex key. • Position the blade in front of the fence. Low ...

  • Craftsman PROFESSIONAL 315.273731 - page 37

    SQUARING BLADE TO FENCE See Figures 30A - 30C. This procedure squares the miter angle of the blade to the fence to reduce the risk of binding and kickback. If the blade is not square to the fence, the yoke assem- bly must be rotated slightly. Have a framing square, a 1/2 in. wrench, and a phillips screwdriver at hand. The blade should be lowered to ...

  • Craftsman PROFESSIONAL 315.273731 - page 38

    PARALLELING BLADE TO TABLE See Figures 31A-31C. This procedure squares the blade to the table at 90 ° bevel so horizontal cuts will be accurate. This also reduces kickback, as well as splintering and burning of the cut edges of the workpiece. If the blade is not at 90 ° bevel, follow the steps to rotate the blade unit slightly. You will need a fr ...

  • Craftsman PROFESSIONAL 315.273731 - page 39

    ALIGNING THE RIP SCALE INDICATORS See Figures 32A - 32B. The rip scale indicators on the arm show the distance between the blade and the rip fence. The upper scale is used when the fence is positioned directly behind the front table. The lower scale is used when the fence is at the extreme rear, directly in front of the column. The in-rip indicator ...

  • Craftsman PROFESSIONAL 315.273731 - page 40

    INSTALLING CONTROL CUT DEVICE See Figure 33. Note: Before installing the control cut device, the yoke assembly will travel back and forward on the carriage by pulling the handle. After installing the control cut device, the power cord for the control cut device must be plugged in and switch trigger pressed to move the yoke assembly and carriage on ...

  • Craftsman PROFESSIONAL 315.273731 - page 41

    BASIC OPERATION OF THE RADIAL ARM SAW A radial arm saw can be used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, compound cutting, and resawing. It can make dado or molding cuts with special attachments. This saw is designed to cut wood and wood composi- tion products only. The three-prong plug must be plu ...

  • Craftsman PROFESSIONAL 315.273731 - page 42

    SWITCH AND SWITCH KEY See Figures 35-37. The main power switch has been placed on the front of the arm for easy access. The yellow switch key prevents accidental starting of the main power switch when saw is not being used. To activate the switch, insert the switch key and lift switch to ON position. To lock the switch once it has been pressed to O ...

  • Craftsman PROFESSIONAL 315.273731 - page 43

    CUTTING AIDS See Figures 38-40. Cutting aids are used to improve the setup and help make the operator's work safer and more accurate. They can be made from scrap wood and in various sizes and shapes for specific projects. The basic types are pushsticks, pushblocks, and featherboards. If the blade is set 2 in. or more from the fence, use a push ...

  • Craftsman PROFESSIONAL 315.273731 - page 44

    MAKING A CROSS CUT See Figure 41. Use this procedure to make a cut with the blade vertical and straight forward. If a kerf does not exist for the line of the cut (cutting path), follow the steps to make one. Each cutting path requires its own kerf. ,_ WARNING: Make sure the blade guard is lowered and is working properly to prevent possible injury. ...

  • Craftsman PROFESSIONAL 315.273731 - page 45

    MAKING A MITER CUT See Figure 42. In a miter cut, the blade is vertical and the arm angled. If a kerf does not exist for the cutting path, make one (instructions below). Each cutting path requires its own kerf. ,_ WARNING: Make sure the blade guard is lowered and is working properly to prevent possible injury. Always raise the clear plastic guard b ...

  • Craftsman PROFESSIONAL 315.273731 - page 46

    MAKING A BEVEL CUT See Figure 43. This procedure makes a cut with the blade and motor angled and the arm straight (90 ° to fence). If there is no kerf, follow the steps to make one. Try this cut on scrap wood before cutting your workpiece. ,_ WARNING: Make sure the blade guard is lowered and is working properly to prevent possible injury. Always r ...

  • Craftsman PROFESSIONAL 315.273731 - page 47

    MAKING A COMPOUND CROSS CUT See Figure 44. In this cut, both the blade and the arm are angled. Be familiar with both bevel and miter cuts before making a compound cut. Practice on scrap wood. ,_ WARNING: Make sure the blade guard is lowered and is working properly to prevent possible injury. Always raise the clear plastic guard before changing the ...

  • Craftsman PROFESSIONAL 315.273731 - page 48

    RiP CUT HAZARDS AND PRECAUTIONS Two hazards are specifically associated with rip cutting: outfeed zone and wrong way feed. In the outfeed zone (behind the blade), the blade teeth point down. The slightest contact while the blade is still spinning can snag clothing, jewelry, the work- piece, or even skin, causing serious personal injury. Wrong way f ...

  • Craftsman PROFESSIONAL 315.273731 - page 49

    • Put the blade in the in-rip position between the motor and the column. Release the yoke lock handle and pivot the yoke to the left, with the yoke pivot latch on the right side of the arm. (Use the out-rip position only for rips 12 in. or more in width; pivot the yoke to the right so the motor is between the blade and column.) • Loosen the car ...

  • Craftsman PROFESSIONAL 315.273731 - page 50

    MAKING OTHER CUTS See Figures 47 and 48. Variations from the basic cuts include cutting long workpieces and non-through cuts. When making one of the following cuts, follow the instructions that apply for the basic cut, depending on the position, shape, and size of the wood. Do not attempt these cuts until you are skilled with the basic cuts. CUTTIN ...

  • Craftsman PROFESSIONAL 315.273731 - page 51

    NON-THROUGH CUTS See Figure 48. ,_ WARNING: Unplug the saw while removing or replacing the blade guard. Turn on the saw with the switch on the arm to confirm the blade is not receiving power. • Remove the blade and blade guard (see Assembly section). • Place a support the same height as the saw table nearby for the cut work. Lower the blade wit ...

  • Craftsman PROFESSIONAL 315.273731 - page 52

    GENERAL MAINTENANCE ,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. ,_ WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw with the switch on the arm, remove the switch key, and unplug the saw before ...

  • Craftsman PROFESSIONAL 315.273731 - page 53

    PROBLEM CAUSE SOLUTION Saw does not start. 1. Motor cord or control-cut cord is 1. Plug in cord. not plugged in. 2. Cord or switch is damaged. 2. Have the cord or switch re- placed at your nearest Sears Service Center. 3. Circuit fuse is blown. 3. Replace circuit fuse. 4. Circuit breaker is tripped. 4. Reset circuit breaker. 5. Switch is burned out ...

  • Craftsman PROFESSIONAL 315.273731 - page 54

    PROBLEM CAUSE SOLUTION Saw vibrates excessively. 1. Blade is warped. 1. Replace the blade. See the removal procedure in Assembly section. 2. Saw is not mounted securely. 2. Tighten all hardware. 3. Work surface is uneven. 3. Reposition on a flat surface. Adjust the leveling feet on legs. Saw is noisy when running. 1. Motor needs attention. 1. Have ...

  • Craftsman PROFESSIONAL 315.273731 - page 55

    PROBLEM CAUSE SOLUTION Handwheel is hard to turn or 1. Sawdust has collected on the 1. column binds, elevating shaft. Saw burns or scores edges of wood in cut. Bevel cuts are not true. 2. Column is out of alignment. 2. 1. Column tube is too loose in the column support. 2. Blade or teeth are bent or dull. 2. 3. Blade is out of alignment. 3. 4. Wrong ...

  • Craftsman PROFESSIONAL 315.273731 - page 56

    PROBLEM CAUSE SOLUTION Miter or cross cuts are not true. 1. Scale pointer is not correct. 1. Reset the pointer at the top rear of arm. 2. Column is out of alignment. 2. See Adjusting the Column Tube in Assembly section. 3. Carriage is misaligned. 3. See Setting the Arm Lock Wheel in the Assembly section. 4. Yoke is loose on carriage. 4. See Setting ...

  • Craftsman PROFESSIONAL 315.273731 - page 57

    PROBLEM CAUSE SOLUTION Saw blade tends to push wood to 1. Blade is heeling. one side when cross cutting. 2. Column tube is loose in column support. 3. Arm is loose or misaligned. 4. Fence/tables are not straight. 5. Blade or teeth are bent or dull. 1. See Squaring the Blade to the Fence in Adjustments section. 2. See Adjusting the Column Tube in As ...

  • Craftsman PROFESSIONAL 315.273731 - page 58

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. l 22 28 17 SEE FIGURE J 21 18 12 11 I0 1 47 29 3O SEE FIGURE I 33 34 ® 37 36 SEE FIGURES F AND G 35 28 FIGURE A ...

  • Craftsman PROFESSIONAL 315.273731 - page 59

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J KEY PART NO. NUMBER 1 976830-001 2 ** STD611006 3 981161-001 4 976793-001 5 981163-001 6 976786-001 7 976834-002 ...

  • Craftsman PROFESSIONAL 315.273731 - page 60

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I 12 13... SEE FIGURE D 65 4 32 FIGURE B SEE FIGURE C 60 I:RRFTSMRN _ RADIAL SAW 315.273731 ...

  • Craftsman PROFESSIONAL 315.273731 - page 61

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I PARTS LIST FOR FIGURE B KEY PART NO. NUMBER DESCRIPTION QUAN. 1 ** STD541031 2 ** STD551131 3 ** STD551031 4 97669 ...

  • Craftsman PROFESSIONAL 315.273731 - page 62

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J 10 FIGURE C 10 3 1 ...

  • Craftsman PROFESSIONAL 315.273731 - page 63

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE C KEY PART NO. NUMBER DESCRIPTION QUAN. 1 977242-001 2 976303-001 3 977241-001 4 976306-00 ...

  • Craftsman PROFESSIONAL 315.273731 - page 64

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I 14 15 27--+ ---17 34-<:_ I 26 22 21 23 FIGURE D 64 # I:RRFTSMRN _ RADIAL SAW 315.273731 ...

  • Craftsman PROFESSIONAL 315.273731 - page 65

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I PARTS LIST FOR FIGURE D KEY PART NO. NUMBER DESCRIPTION QUAN. 1 981981-001 2 976308-001 3 976386-001 4 976296-001 ...

  • Craftsman PROFESSIONAL 315.273731 - page 66

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I 12 14 15 21 22 23 16 19 20 _ 131 18 24 26 FIGURE E 66 I:RRFTSMRN _ RADIAL SAW 315.273731 ...

  • Craftsman PROFESSIONAL 315.273731 - page 67

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I PARTS LIST FOR FIGURE E KEY PART NO. NUMBER DESCRIPTION QUAN. 1 622210-043 2 976323-001 3 976326-002 4 980613-001 ...

  • Craftsman PROFESSIONAL 315.273731 - page 68

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I 7 8 3O 22 31 FIGURE F SEE FIGURE G 32 " , 33 # 68 I:RRFTSMRN _ RADIAL SAW 315.273731 ...

  • Craftsman PROFESSIONAL 315.273731 - page 69

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I PARTS LIST FOR FIGURE F KEY PART NO. NUMBER DESCRIPTION QUAN. 1 981151-001 2 976358-001 3 ** STD511105 4 976287-00 ...

  • Craftsman PROFESSIONAL 315.273731 - page 70

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I 15 SEE FIGURE F 14 13 11 10 18 2O 19 SEE FIGURE H 21 22 22 33 25 - _ 2"- -_. -_. _29 FIGURE G # 70 I:RRFTSHRN ...

  • Craftsman PROFESSIONAL 315.273731 - page 71

    CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 • The model number will be found on a plate attached to the base. Always mention the model num- I ber in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts. I PARTS LIST FOR FIGURE G KEY PART NO. NUMBER DESCRIPTION QUAN. 1 976773-001 2 976284-001 *** 4 976271-001 5 976272- ...

  • Craftsman PROFESSIONAL 315.273731 - page 72

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J FIGURE H 7 10 .J .J j" ...

  • Craftsman PROFESSIONAL 315.273731 - page 73

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE H KEY PART NO. NUMBER DESCRIPTION QUAN. 1 610122-006 2 976449-001 3 971665-001 4 977207-00 ...

  • Craftsman PROFESSIONAL 315.273731 - page 74

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL I ! ARM SAW or when ordering repair parts. J 20 21 17 25 18 24 13 10 19 12 11 9 8 3_ 16 32 3 30 31 FIGURE I 2 ...

  • Craftsman PROFESSIONAL 315.273731 - page 75

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE I KEY PART NO. NUMBER DESCRIPTION QUAN. 1 976366-001 2 977237-001 3 976370-002 4 979528-00 ...

  • Craftsman PROFESSIONAL 315.273731 - page 76

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J 2 SEE FIGURE K 7 8 ./ ./ / J 11 10 j" 12 FIGURE J ...

  • Craftsman PROFESSIONAL 315.273731 - page 77

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE J KEY PART NO. NUMBER DESCRIPTION QUAN. 1 607818-002 2 990908-009 3 976450-001 4 ** STD511 ...

  • Craftsman PROFESSIONAL 315.273731 - page 78

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J 1 4 FIGURE K ...

  • Craftsman PROFESSIONAL 315.273731 - page 79

    • CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.273731 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL | ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE K KEY PART NO. NUMBER DESCRIPTION QUAN. ** STD510803 662028-001 976420-001 976421-001 1 2 ...

  • Craftsman PROFESSIONAL 315.273731 - page 80

    Owner's Manual STOCK NO. 927373 MODEL NO. 315.273731 Sears service is available at or through your Sears Retail Store or Catalogue Sales Office. How to order repair parts SERVICE AND REPAIR PARTS CALL 1-800-665-4455* Keep this number handy should you require a service call or need to order repair parts. If ordering parts, make sure you have th ...

Manufacturer Craftsman Category Saw

Documents that we receive from a manufacturer of a Craftsman PROFESSIONAL 315.273731 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- PROFESSIONAL 315.273731 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman PROFESSIONAL 315.273731
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman PROFESSIONAL 315.273731.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman PROFESSIONAL 315.273731, service manual, brief instructions and user manuals Craftsman PROFESSIONAL 315.273731. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman PROFESSIONAL 315.273731.

A complete manual for the device Craftsman PROFESSIONAL 315.273731, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman PROFESSIONAL 315.273731 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman PROFESSIONAL 315.273731.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman PROFESSIONAL 315.273731 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman PROFESSIONAL 315.273731, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman PROFESSIONAL 315.273731, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman PROFESSIONAL 315.273731 - which should help us in our first steps of using Craftsman PROFESSIONAL 315.273731
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman PROFESSIONAL 315.273731
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman PROFESSIONAL 315.273731 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman PROFESSIONAL 315.273731?

Use the form below

If you did not solve your problem by using a manual Craftsman PROFESSIONAL 315.273731, ask a question using the form below. If a user had a similar problem with Craftsman PROFESSIONAL 315.273731 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)