English dropdown-ico

Manual TP-Link TD-8817

74 pages 1.94 mb
Download

Go to site of 74

Summary
  • TP-Link TD-8817 - page 1

    TD-8817 ADSL2+ Ethernet/USB Modem Router Rev: 3.0.0 1910010897 ...

  • TP-Link TD-8817 - page 2

    COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other br ands and product names are trademarks or registered trademarks of t heir respective holders. No part of the specificat ions may be reproduced in any form or b y any means or used to make any derivativ ...

  • TP-Link TD-8817 - page 3

    FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Ru les. These limits are designed to pr ovide reasonable protectio n against harmful interference in a residential installation. This equipment ge nerates, uses and can radiate radio frequency energy and, if ...

  • TP-Link TD-8817 - page 4

    Safety Information  When product has power button, the power butto n is one of the way to shut off the product; when there is no power button, the only way to co mpletely shut off power is to disconnect the product or the power adapter from the power source.  Don’t disassemble the product, or make repairs yourself. You run the risk of elect ...

  • TP-Link TD-8817 - page 5

    TP-LINK TECHNOLOGIES CO., LTD DECLARA TION OF CONFORMITY For the following equipment: Product Description: ADSL2+ Ethernet/USB Modem Router Model No.: TD-8817 T rademark: TP-LINK We declare under our own respon sibility that the above products satisfy all the technical regulations applicable to the product wi thin the scope of Council Directives: D ...

  • TP-Link TD-8817 - page 6

    CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Product Overview ..................................................................................... ...

  • TP-Link TD-8817 - page 7

    4.5.6 CWMP ............................................................................................................................ 52 4.6 Maintenance ............................................................................................................ 52 4.6.1 Administration .............................................................. ...

  • TP-Link TD-8817 - page 8

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 1 Package Contents The following items should be found in your package:  One TD-8817 ADSL2+ Ethernet/USB Modem Router  One Power Adapter for TD-8817 ADSL2+ Ethernet/USB Modem Router  Quick Installation Guide  One RJ45 cable  One USB cable  Two RJ11 cables  One ADSL splitter ? ...

  • TP-Link TD-8817 - page 9

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 2 Chapter 1. Introduction Thank you for choosing the TD-8817 ADSL2+ Ethernet/USB Modem Router. 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. TD-8817 connects to an Ethernet LAN or com puters via standard ...

  • TP-Link TD-8817 - page 10

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 3  Built-in DHCP server.  Built-in firewall, supports IP/MAC filter, Application filter and URL filter.  Supports Virtual Server, DMZ host and IP Address Mapping.  Supports Dynamic DNS, UPnP and Static Routing.  Supports system log and flow Statistics.  Supports firmware upgrade ...

  • TP-Link TD-8817 - page 11

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4 Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs are located on the front panel, they indicate the device’ s working status . For details, please refer to LED Explanation . LED Explan ation: Name Status Indication On The modem router is powered on. Power Off The modem r ...

  • TP-Link TD-8817 - page 12

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 5 configuration. You may need to check this part of information with your ISP and make sure everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet for more information. 2.2 The Back Panel Figure 2-2  ON/OFF : The switch for the power.  POWER : The Power plug is w ...

  • TP-Link TD-8817 - page 13

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 6 Figure 2-3  Note: The diameter of the screw, 4mm<D<7.5mm, and the distance of two sc rews is 111.5mm. The screw that project from the wall need around 4m m based, and t he length of the screw need to be at least 20mm to withstand t he weight of the product. 2.4 Hardware Installation Pro ...

  • TP-Link TD-8817 - page 14

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 7 Figure 2-4 ...

  • TP-Link TD-8817 - page 15

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 8 Chapter 3. Quick Installation Guide 3.1 TCP/IP Configuration The default IP address of the TD-8817 ADSL2+ Ethernet/USB Modem Router is 192.168.1.1. And the default Subnet Mask is 255.255. 255.0. These values can be c hanged as you desire. In this guide, we use all the default values for descript ...

  • TP-Link TD-8817 - page 16

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 9 Figure 3-2 You can check it follo wing the steps below: 1) Is the connection betw een your PC and the modem router correct? The LEDs of LAN port which you link to the dev ice and the LEDs on y our PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the modem r ...

  • TP-Link TD-8817 - page 17

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 10 Figure 3-3 Step 3: You will see Figure 3-4 as follow, please wait a moment. Figure 3-4 Step 4: After that, you will see Figure 3-5 . Click Finish to complete the installation. ...

  • TP-Link TD-8817 - page 18

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 11 Figure 3-5  Note: 1) All of the above settings are under windows XP. 2) If you want to pull out the USB device y ou must disconnect the network of USB first. 3) In the Vista operating sy stem, maybe the “Unknown Device” screen will pop up when you insert the USB cable of the Router to a ...

  • TP-Link TD-8817 - page 19

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 12 Figure 3-6 Step 1: Select the Quick Start tab, then click RUN WIZARD , and you will see Figure 3-7 . Click the NEXT button. Figure 3-7 Step 2: Configur e the time for the Router, and then click the NEXT button. Figure 3-8 Step 3: Select the connection type to c onnect to the ISP (We select PPPo ...

  • TP-Link TD-8817 - page 20

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 13 Figure 3-9 Step 4: Configur e the following opti ons provided by your ISP: Username , Password , VPI , VCI and Connection Type . Then click NEXT . Figure 3-10 Step 5: Click NEXT to finish the Quick Start. Figure 3-1 1 ...

  • TP-Link TD-8817 - page 21

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 14 Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more abo ut this device and make use of its functions adequately, maybe you will get help from this chapter to configur e th ...

  • TP-Link TD-8817 - page 22

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 15 Figure 4-2 4.1.2 System Log Choose “ Status → System Log ” menu, and you will be able to quer y the logs of the Router. ...

  • TP-Link TD-8817 - page 23

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 16 Figure 4-3 The modem router can keep logs of all traffic. Y ou can query the logs to find what happened to the modem router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose “ Status → Statistics ” menu, and you will be able ...

  • TP-Link TD-8817 - page 24

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 17  Interface: You can select Ethernet and ADSL to view the corresponding network traffic over different ports.  Select Ethernet , and you will see the statistics table as below. Statistics Table: Transmit Frames The frames transmitted over the Ethernet port. Transmit Multicast Frames The mu ...

  • TP-Link TD-8817 - page 25

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 18 4.2 Quick S t art Please refer to 3.3 Login . 4.3 Interface Setup Choose “ Interface Setup ”, you can see the next submenus: Internet and LAN . Figure 4-5 Click any of them, and you will be able to configure the corre sponding function. 4.3.1 Internet Choose “ Interface Setup → Internet ...

  • TP-Link TD-8817 - page 26

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 19 Figure 4-6  ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In th is Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 di fferent virtual circuits from your ...

  • TP-Link TD-8817 - page 27

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 20  Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7.  Status: If you want to use a designed VC, you should activate it.  VPI: Identifies the virtual path bet ween endpoints in an ATM ne twork. The valid range is from 0 to 255. Please input the value provided by your ISP ...

  • TP-Link TD-8817 - page 28

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 21 Figure 4-7  Encapsulation: Select the encapsulation mode for the Dy namic IP Address, you can leave it default.  Bridge Interface: Activate the option, t he modem router can also work in Bridge mode.  Default Route: If enable this function, the current PVC will be consider ed as the de ...

  • TP-Link TD-8817 - page 29

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 22 2. Static IP Address Select this option if your ISP provides static IP information for you. You should set static IP address, IP Subnet Mask, and Gateway address in the screen below (shown in Figure 4-12 ). Figure 4-8  Note: Each IP address entered in the fields must be in t he appropriat e ...

  • TP-Link TD-8817 - page 30

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 23 Figure 4-9  Service name: Specify a name for the PPPoA/PPPoE connection for recognition.  Username: Enter your username for your PPPoA/ PPPoE connection to identify and verify your account to the ISP.  Password: Enter your password for your PPPoA/PPPoE connection.  Encapsulation: Fo ...

  • TP-Link TD-8817 - page 31

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 24 or given by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and Gateway IP address.  Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by default. 4. Bridge Mode If you select this type of connection, the modem router can be ...

  • TP-Link TD-8817 - page 32

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 25 Figure 4-1 1  IP Common Option: Configure the IP common option here.  Encapsulation: Select the encapsulation mode for the Dy namic IP Address, you can leave it default.  Bridge Interface: Activate the option, t he modem router can also work in Bridge mode.  Default Route: If enable ...

  • TP-Link TD-8817 - page 33

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 26 Figure 4-12  Note: Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon (x:x:x:x :x:x:x:x). The modem router will not accept the IP address if it is not in this format. 3. PPPoA/PPPoE Select this option if your ISP requires ...

  • TP-Link TD-8817 - page 34

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 27 Figure 4-13  Service name: Specify a name for the PPPoA/PPPoE connection for recognition.  Username: Enter your username for your PPPoA/ PPPoE connection to identify and verify your account to the ISP.  Password: Enter your password for your PPPoA/PPPoE connection.  Encapsulation: F ...

  • TP-Link TD-8817 - page 35

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 28 enable the function, please click Enable .  MLD Proxy: The MLD (Multicast Listener Discovery Pr otocol) Proxy function is disabled by default. If you want to enable the function, please click Enable .  Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disa ...

  • TP-Link TD-8817 - page 36

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 29 Figure 4-15  Router Local IP: These are the IP settings of the LA N interface for the device. These settings may be referred to as Private se ttings. You may change the LAN IP addres s if needed. The LAN IP address is private to y our internal networ k and cannot be seen on the Internet.  ...

  • TP-Link TD-8817 - page 37

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 30 means the ADSL modem router will only send but will not accept RIP packet.  Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer pr otocol used to establish mem bership in a multicast group. The ADSL ATU-R supports both IGMP ver ...

  • TP-Link TD-8817 - page 38

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 31  Primary DNS Server: Type in your preferred DNS server.  Secondary DNS Server: Type in your preferred DNS server.  Note: If Use Auto Discovered DNS Server Onl y is selected in DNS Relay , this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP ...

  • TP-Link TD-8817 - page 39

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.4 Advanced Setup Choose “ Advanced Setup ”, you can see the next submenus: Figure 4-18 Click any of them, and you will be able to configure the corre sponding function. 4.4.1 Firewall Choose “ Advanced Setup → Firew all ” menu, and you will see the next screen (shown in Figure 4-19 ). ...

  • TP-Link TD-8817 - page 40

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 33 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-21 ). Figure 4-21  Destination IP Address: This parameter spec ifies the IP network address of the final destination.  IP Subnet Mask: Enter the subnet mask for this destination.  Gateway IP Address: Enter ...

  • TP-Link TD-8817 - page 41

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 34  Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function.  NAT Status: This field shows the current statu s of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-6 ) to activate the function.  Number of IPs; This f ...

  • TP-Link TD-8817 - page 42

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 35 Figure 4-24  Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules.  Start & End port number: Enter the specific Start and End Po rt number you want to forward. If it is one port on ...

  • TP-Link TD-8817 - page 43

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 36 Other operations for the entries are as follows: Enter the index of assigned entry, click the DELETE button to delete the entry. Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configur ation which is made just now. 4.4.3.3. IP Address Mapping Choos ...

  • TP-Link TD-8817 - page 44

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 37 ati on about the Mapping addresses. Circuit” and Multiple fo r the “Number of IPs”. Then select the tab IP  Mapping is only available for VCs with Multiple IPs. 6 . nding fields. button to delete the entry. ch is made just now. 4.4.4 QoS nced Setup → QoS ”, you can configure the Qo ...

  • TP-Link TD-8817 - page 45

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 38 Figure 4-27  QoS: Select this option to Activa te/Deac tivate the IP QoS on different types.  Summary: Click the button to view t he configurations of QoS.  Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to d ...

  • TP-Link TD-8817 - page 46

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 39 application.  Vlan ID Range: Enter the Vlan range, then the rule will be effective to the selected Vlans.  IPP/DS Field: Select the type of the action to assign the priority. When you select IPP/TOS, you can assign the prio rity via IP informati on. IP QoS function is intended to deliver ...

  • TP-Link TD-8817 - page 47

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 40 ffic complies with the rule, then the Router will he rule. the rule. iori t y via DHCP (the header of IP group). It maps nfigure the action that the Router takes to deal with the traffic which accord with the DSCP priority.  Queue #: Select the priority type for the action. ment, ba ndwidth ...

  • TP-Link TD-8817 - page 48

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 41 Figure 4-30  VLAN Index: Select the VLAN index for this VC. You can specify 8 gr oups in maximum.  VLAN ID: This indicates the VLAN group.  ATM VCs: Select the ATM VCs as members of VLAN , and if you leave the Tagged blank, the tag in frames will be deleted wh en transmitted from the V ...

  • TP-Link TD-8817 - page 49

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 42 Figure 4-31  PVID: Each physical port has a default VID ca lled PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frame s with null (0) VID) received on this port. 4.4.6 ADSL Choose “ Advanced Setup → ADSL ”, you can select the ADSL Type and ADSL Mode in t ...

  • TP-Link TD-8817 - page 50

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 43 4.5 Access Management Choose “ Access Management ”, you can see t he next submenus: Figure 4-33 Click any of them, and you will be able to configure the corre sponding function. 4.5.1 ACL Choose “ Access Management → ACL ”, you can see the next screen (show n in Figure 4-34 ). You can ...

  • TP-Link TD-8817 - page 51

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 44 4.5.2 Filter Choose “ Access Management → Filter ”, you can see the Filter screen (the default is IP/MAC Filter screen shown in Figure 4-35 ). The filtering feature includes IP /MAC Filter, Application Filter, URL Filter. The feature makes it pos sible for administrators to control user&a ...

  • TP-Link TD-8817 - page 52

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 45  Note: If select PVC0~PVC7 as a interface, the filter will match the IP tr affic of WAN port with specified IPs (Source IP Address and Destination IP Address), If select LAN as a interface, the filter will match the IP traffic of LA N port with specified IPs.  Direction: Select the direct ...

  • TP-Link TD-8817 - page 53

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 46 Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select t he Direction “Both” for the first rule.  Note: If you want to make the rule take ef fect, please select Ye s to active the rule. Step 3: Enter the “S ...

  • TP-Link TD-8817 - page 54

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 47 Other operation for the entries as shown in Figure 4-35 : Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry . Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the ...

  • TP-Link TD-8817 - page 55

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 48 Step 1: Select the “IP/MAC Filter” as the Filer Type Selection: Select the “MAC” as the Rule Type on the Filter screen (show in Figure 4-36 ). , Then you can configure the spec ific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rul ...

  • TP-Link TD-8817 - page 56

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 49 Figure 4-37  Filter Type Selection: Select the Application Filter for the next configuration.  Application Filter: Activate or deactivate the function.  ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Den y for these applications. If you select Allow , the modem router ...

  • TP-Link TD-8817 - page 57

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 50  Filter Type Selection: Select the URL Filter fo r the next configuration.  Active: Select “Yes” to make t he rule to take effect.  URL Index: Select the index for the URL Filter entry.  URL: Enter the URL for this URL Filter.  URL Filter Listing: This displays the informati ...

  • TP-Link TD-8817 - page 58

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 51 simple peer-to-peer network connec tivity between devices. An UPnP device can dynamically joi n a network, obtain an IP address, convey its c apabilities and learn about other devices on the network. In turn, a device can l eave a network smoothly and automatically when it is no longer in use. ...

  • TP-Link TD-8817 - page 59

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 52 4.5.6 CWMP Choose “ Access Management → CWMP ”, you can configure the CW MP function in the screen (shown in Figure 4-42 ). The modem router offers CWMP feature. The functi on supports TR-069 protocol which collects information, diagnoses the devices and configures the devic es automatica ...

  • TP-Link TD-8817 - page 60

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 53 4.6.1 Administration Choose “ Maintenance → Administration ”, you can set new password for admin in the screen (shown in Figure 4-44 ). Figure 4-44  Note: 1) There is only one account that can access Web-Management interface. The default account is "admin", and the password i ...

  • TP-Link TD-8817 - page 61

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 54 Figure 4-45  Note: The ADSL modem router built-in some NTP Serv ers, when the modem router connects to the Internet, the modem router will get the system ti me automatically from the NTP Server . Y ou can also configure the NTP Server address manually , and then the modem router will get the ...

  • TP-Link TD-8817 - page 62

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 55 Figure 4-47 4.6.3 Firmware Choose “ Maintenance → Firmware ”, you can upgrade the firmware of the modem router in the screen (shown in Figure 4-48 ). Make sure the firmware or romf ile you want to use is on the local hard drive of the computer. Click Brow se to find the local hard drive a ...

  • TP-Link TD-8817 - page 63

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 56 recent firmware version, unl ess the version has a new feat ure that you want to use. 2) When you upgrade the modem route r 's firmwa re, you may lose it s current configurations, so please back up the modem router’s curr ent settings before you upgrade its firmware. 3) Do not turn off t ...

  • TP-Link TD-8817 - page 64

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 57 Step 2: Click the UPGRADE button to complete. 4.6.4 SysRestart Choose “ Maintenance → SysRe start ”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-51 ). Figure 4-51 4.6.5 Diagnostics Choose “ Maintenanc ...

  • TP-Link TD-8817 - page 65

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 58 4.7 Help Choose “ Help ”, you can view the help information for configuration of any function. Figure 4-53  Note: Click the tab, and you will be able to get the corresponding information. ...

  • TP-Link TD-8817 - page 66

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 59 Appendix A: Specifications General Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G. 992.2, ITU G.992.3, ITU G.992.5 IEEE 802.3, IEEE 802.3u, TCP/IP , PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT,CWMP Safety & Emission FCC, CE Ports 1 10/100M Auto-Negotiation RJ45 port （ Auto MDI/MDI ...

  • TP-Link TD-8817 - page 67

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 60 Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP corr ectly in Windows XP. First make sure your Ethernet Adapter is worki ng, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the ...

  • TP-Link TD-8817 - page 68

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 61 Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below:  Setting IP address automatically Select Obtain an IP address automatically , Choose Obtain DNS server aut ...

  • TP-Link TD-8817 - page 69

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 62 Figure B-3  Note: For Windows 98 OS or before, the PC and modem router may need to be rest arted.  Setting IP address manually 1 Select Use the following IP address radio button. And the fo llowing items available 2 If the modem router's LAN IP address is 192.168.1. 1, specify the IP ...

  • TP-Link TD-8817 - page 70

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 63 Figure B-4 Now: Click OK to keep your settings. ...

  • TP-Link TD-8817 - page 71

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 64 Appendix C: Troubleshooting T1. How do I restore m y modem router’s configuration to its f actory default settings? With the modem router powered on, press and hold the RESET button on the rear pan el for 8 to 10 seconds before releasing it.  Note : Once the modem router is reset, the curr ...

  • TP-Link TD-8817 - page 72

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 65 d) Select Obtain an IP address automatically and Obtain DNS server address automatically . Then click OK . For Windows 8 a) Move your mouse to the lowe r right corner and you will see S earch icon in the Popups. Go to “ -> Apps ”. Type Control Panel in the search box and press Enter , th ...

  • TP-Link TD-8817 - page 73

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 66 Now, try to log on to the Web-based configur ation page again after the above settings have been configured. If you still cannot acce ss the configuration page, please restore your modem router’s factory default settings and re configure your modem router follow ing the instructions in 3.3 Lo ...

  • TP-Link TD-8817 - page 74

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 67 Appendix D: Technical Support Appendix D: Technical Support Technical Support Technical Support  For more troubleshooting help, go to:  For more troubleshooting help, go to: www.tp-link .com/en/support/faq www.tp-link.com/en/sup port/faq  T o download the latest Firmware, Driver , Util ...

Manufacturer TP-Link Category Saw

Documents that we receive from a manufacturer of a TP-Link TD-8817 can be divided into several groups. They are, among others:
- TP-Link technical drawings
- TD-8817 manuals
- TP-Link product data sheets
- information booklets
- or energy labels TP-Link TD-8817
All of them are important, but the most important information from the point of view of use of the device are in the user manual TP-Link TD-8817.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TP-Link TD-8817, service manual, brief instructions and user manuals TP-Link TD-8817. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TP-Link TD-8817.

Similar manuals

A complete manual for the device TP-Link TD-8817, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TP-Link TD-8817 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TP-Link TD-8817.

A complete TP-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TP-Link TD-8817 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TP-Link TD-8817, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TP-Link TD-8817, that we can find in the current document
3. Tips how to use the basic functions of the device TP-Link TD-8817 - which should help us in our first steps of using TP-Link TD-8817
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TP-Link TD-8817
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TP-Link TD-8817 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TP-Link TD-8817?

Use the form below

If you did not solve your problem by using a manual TP-Link TD-8817, ask a question using the form below. If a user had a similar problem with TP-Link TD-8817 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)