English dropdown-ico

Manual Briggs & Stratton 592

13 pages 4.88 mb
Download

Go to site of 13

Summary
  • Briggs & Stratton 592 - page 1

    Edger Model 592 IMPOR T ANT : READ SAFETY RULES AND INSTR UCTIONS CAREFULL Y TR O Y-BIL T LLC P .O . BO X 361 131 C LEVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal combustion engine and should not be used on or ne ar any unimproved forest- covered, brush-covered or gr ass-covered land unless the engine’s exhaust system ...

  • Briggs & Stratton 592 - page 2

    2 TABLE OF CONTENTS Content P age Importa nt Safe Operati on Practices ................. ............. ................... ............. .....3 Assembli ng The E dger ................. ............. .................... ............ .................... .....5 Know The Edge r. ............. .................... ............. ................... ... ...

  • Briggs & Stratton 592 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARN ING: TH IS SYMB OL PO INTS O UT IMPO RTAN T SAFET Y INST RUCTI ONS W HICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROP ERTY OF YOURSELF AND OTHERS. READ AN D FOLLOW ALL I NSTRUC TIONS IN THIS MANUA L B EFORE ATTEMP TING TO OPERATE THIS MACH INE. FAILURE TO COMPLY WITH THE SE I ...

  • Briggs & Stratton 592 - page 4

    4 4. Never ope rate with damage d safety dev ices. Failure to d o so, c an res ult in person al inj ury. 5. Never run an engine indoo rs or in a poor ly ventila ted area. En gine exhaust c ontains ca rbon monoxid e, an odorle ss and d eadly gas. 6. Do not opera te machine while under the in fluence of alcohol or drugs. 7. Muffler and engine bec ome ...

  • Briggs & Stratton 592 - page 5

    5 SECTION 2: ASSEMBLING YOUR EDGER IMPORT ANT: This unit is shipped WITHOUT GASOLINE or OIL. After se tting up th e unit, servic e engine with gasoli ne and oil as ins tructed i n the Briggs & Stratton Owner /Operato r Manual pa cked with your edger. NOTE: Reference to right or left hand s ide of t he edg er is observ ed from the opera ting pos ...

  • Briggs & Stratton 592 - page 6

    6 Figure 5 IMPORT ANT: Perform the cl utch rod ad justment be fore operatin g the edger. Clutch Ro d Adjustment Before op erating th e edger, ch eck the adjus tment of the clutch r od as follow s: • Discon nect the spa rk plug wire an d ground it as instru cted earlier in this sectio n. Refer to Figure 2. • With the bl ade clutc h/depth cont ro ...

  • Briggs & Stratton 592 - page 7

    7 Figure 6 SECTION 4: OPERATING THE EDGER The operation of any edger can result in foreign objects being thrown into the eyes, w hich can re sult in severe eye dama ge. Always wear safet y glasse s or eye shields. W e recommend wide vision safety mask for ove r spectacles or standa rd safety g lasses WARNING: D o not lower blade if blade is over co ...

  • Briggs & Stratton 592 - page 8

    8 • Move the thr ottle control le ver on the eng ine int o the ST OP or O FF pos ition . IMPORT ANT: Make certain that the engi ne ’ s spark pl ug wire is prop erly ground ed as instruc ted in SECTIO N 2: Assemb ling The Edge r before st oring the ed ger for its next use. Ref er to Figure 2. Engaging th e Edger Blade WARNING: The bla de clutch ...

  • Briggs & Stratton 592 - page 9

    9 Edger Blade Angle Adjustment WARNING: Rotating cutting b lade may throw objects causing person al inju ry. Keep area clear o f bystand ers and do not oper ate without guards in plac e. The cutting blade can be adjusted to eight posi tions. T o adjust the bl ade angle, proc eed as foll ows: • Place the blade clu tch/depth c ontrol lever in th e ...

  • Briggs & Stratton 592 - page 10

    10 Trim ming Placin g the blade angl e adjustme nt lever i n the notch furthest to the left wil l put the spin dle assem bly at a proper an gle for trimmi ng with the edger as illustrate d in Figure 13. IMPORT ANT: When the spin dle asse mbly is rotate d counte r-clock wise ( putting the b lade cl oser t o a horizontal position ), it IS necessar y ...

  • Briggs & Stratton 592 - page 11

    11 Fig ure 1 5 Replac ing the Edger Blade • Use two wren ches (one wr ench to preven t the hex bolt head from spinni ng and the other t o remove the hex lock nut) to remo ve the edger blade. See Figure 16. Fig ure 1 6 • Remove an d discard the edger blade but retain the bell washe r and hex lo ck nut. • Install the replaceme nt edger bla de, ...

  • Briggs & Stratton 592 - page 12

    12 Off-Season Storage Observe the following when preparin g the edger for long-ter m storag e: • Clean an d lubric ate unit t horoughl y as ins tructed on page 10 of this manual. • Refer to the Service, Storage & Specifications secti on of the Briggs & Stratt on Owner/O perator M anual packed with the edger for eng ine storage instruc t ...

  • Briggs & Stratton 592 - page 13

    MANUF A CTURER ’ S LIMITED W ARRANTY FOR: The lim ited warranty set forth below is given b y Troy-Bil t LLC with res pect to new mercha ndise pu rchased and used in the United States, its posses sions and territor ies. Troy-Bilt L LC warran ts this p roduct ag ainst def ects for a period of two (2) y ears co mmencin g on the date o f original pur ...

Manufacturer Briggs & Stratton Category Trimmer

Documents that we receive from a manufacturer of a Briggs & Stratton 592 can be divided into several groups. They are, among others:
- Briggs & Stratton technical drawings
- 592 manuals
- Briggs & Stratton product data sheets
- information booklets
- or energy labels Briggs & Stratton 592
All of them are important, but the most important information from the point of view of use of the device are in the user manual Briggs & Stratton 592.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Briggs & Stratton 592, service manual, brief instructions and user manuals Briggs & Stratton 592. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Briggs & Stratton 592.

Similar manuals

A complete manual for the device Briggs & Stratton 592, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Briggs & Stratton 592 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Briggs & Stratton 592.

A complete Briggs & Stratton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Briggs & Stratton 592 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Briggs & Stratton 592, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Briggs & Stratton 592, that we can find in the current document
3. Tips how to use the basic functions of the device Briggs & Stratton 592 - which should help us in our first steps of using Briggs & Stratton 592
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Briggs & Stratton 592
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Briggs & Stratton 592 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Briggs & Stratton 592?

Use the form below

If you did not solve your problem by using a manual Briggs & Stratton 592, ask a question using the form below. If a user had a similar problem with Briggs & Stratton 592 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)