Manual Honeywell R4795A

16 pages 0.34 mb
Download

Go to site of 16

Summary
  • Honeywell R4795A - page 1

    1 60-2285—7 R4795A Flame Safeguard Primary Contr ols The R4795A Protectorelay™ Primary Control provides solid state electronic flame safeguard protection for commercial and industrial gas or oil burn ers. It provides a prepurge period before each start, and intermittent pilot. ■ 120V models meet the requirements of Underwrit- ers Laboratories ...

  • Honeywell R4795A - page 2

    60-2285—7 2 R4795A SPECIFICATIONS • ORDERING INFORMATION Specif ications R4795A Flame Safeguard Primary Control recycles once after flame failure to try to re-establish pilot before lockout. Use with R7289A Amplifier and rectifying flame rod, recti- fying photocell, or C7012A,C Purple Peeper Ultraviolet Flame Detector; or with R7290A Amplifier ...

  • Honeywell R4795A - page 3

    3 60-2285—7 R4795A SPECIFICATIONS TERMINAL RATINGS: Terminal Load Rating 3 Pilot Valve 125 VA pilot duty. Intermittent Ignition a 360 VA. 4 Interrupted Ignition 360 VA. 5 Main Fuel Valve(s) 125 VA pilot duty, or 25 VA pilot duty plus one or more motorized valves with total rating up to 400 VA opening, 200 VA holding. 6-7 Airflow Switch 0.6A at 30 ...

  • Honeywell R4795A - page 4

    60-2285—7 4 R4795A INSTALLATION Installation Vibration Do not install the R4795A where it could be subject to excessive vibration. Vibration shortens the life of the elec- tronic and mechanical components. Weather The R4795A is not designed to be weathertight. If it is installed outdoors, use a suitable weathertight enclosure. Mounting The Subbas ...

  • Honeywell R4795A - page 5

    5 60-2285—7 R4795A INSTALLATION IMPORTANT: Do not run high voltage ignition trans- former wires in the same conduit with the flame detector wiring. 5. For ignition installations in a contaminating environ- ment, use Honeywell Specification no. R1239001 High Ten- sion Ignition Cable or equivalent. This wire is very resistant to severe conditions o ...

  • Honeywell R4795A - page 6

    60-2285—7 6 R4795A INSTALLATION Replacing RA890E,F,G with R4795A 1. Disconnect all wires from terminal 1, and splice with solderless connector. (If RA890 has no terminal 1 wiring, disregard this step.) 2. Remove line voltage controller wire from terminal 6 and connect to terminal 1. 3. Move burner motor connection from terminal 3 to ter- minal 6 ...

  • Honeywell R4795A - page 7

    7 60-2285—7 R4795A INSTALLATION Fig. 6—Flame detector wiring. M8686 BLUE WHITE F G C7027, C7035, OR C7044 ULTRAVIOLET FLAME DETECTOR BLUE YELLOW BLACK BLACK F G C7012 ULTRAVIOLET DETECTOR 1 G F X X X X X X FLAME ROD G F X X PHOTOCELL 1 C7027, C7035, AND C7044 FLAME DETECTOR LEADS ARE COLOR CODED BLUE AND WHITE. THE BLUE LEAD MUST BE CONNECTED T ...

  • Honeywell R4795A - page 8

    60-2285—7 8 R4795A CHECKOUT Check out Fig. 10—Internal view showing amplifier and test jack for flame current test. CA UTION Use extreme care while testing the R4795; line voltage can be present on most terminals when the power is On. CHECKOUT SUMMARY The following list summarizes the checkout tests re- quired for each type of installation. Ins ...

  • Honeywell R4795A - page 9

    9 60-2285—7 R4795A CHECKOUT 2. The flame current is at least two microamperes for R7289A Rectification Amplifier (color-coded green), or at least 1.5 microamperes for an R7290A Ultraviolet Amplifier (color-coded violet). IF A STEADY READING OF AT LEAST MINIMUM STRENGTH CANNOT BE OBTAINED, ONE OR MORE OF THE FOLLOWING CONDITIONS CAN EXIST: • Imp ...

  • Honeywell R4795A - page 10

    60-2285—7 10 R4795A CHECKOUT CA UTION Do not manually push in the relays. 4. Check that the pilot is lit and relay 2K is pulled in. 5. Open the manual main burner shutoff cock. Main flame should light within one second. If the burner does not light within one second, close the shutoff cock and shut off power to the relay. Proceed to step 7. 6. If ...

  • Honeywell R4795A - page 11

    11 60-2285—7 R4795A OPERATION • TROUBLESHOOTING Operation NORMAL OPERATION (REFER TO FIG. 2 AND 3.) Call for Heat (Limit Switch Closed) Terminal 1 energized. Relay 3K pulls in to close contact 3K2 and energize terminal 8 fan or burner motor. Airflow Proved Low voltage airflow switch between terminals 6 and 7 closes to energize the purge timer. ...

  • Honeywell R4795A - page 12

    60-2285—7 12 R4795A TROUBLESHOOTING F. Pilot lights and relay 2K pulls in but the main burner does not light. G. Relay 2K remains in after flame is extinguished. H. Miscellaneous problems: 1. Repeated lockouts or control failures. 2. Ignition interference (flame rod installations only). TROUBLESHOOTING PROCEDURES CA UTION 1. Use extreme care whil ...

  • Honeywell R4795A - page 13

    13 60-2285—7 R4795A TROUBLESHOOTING • SERVICE (3) Remove any flame simulating condition such as false light. (4) Note that any change made in the detector or its sighting requires a pilot turndown test. 3. If using an R7290 Ultraviolet Amplifier, replace the amplifier and recheck the flame relay dropout time. If the flame relay dropout timing i ...

  • Honeywell R4795A - page 14

    60-2285—7 14 R4795A SERVICE IMPORTANT: 1. Do not clean contacts unless absolutely necessary. 2. Use only Honeywell Contact Cleaner part no. 132569. Do not use any other type of contact cleaner. 3. Use extreme care to avoid bending the contacts or changing the specifications or configuration in any way. 4. Do not use an abrasive or a burnishing to ...

  • Honeywell R4795A - page 15

    15 60-2285—7 ...

  • Honeywell R4795A - page 16

    Home and Building Control Home and Building Control Honeywell Inc. Honeywell Limited—Honeywell Limitée 1985 Douglas Drive North 740 Ellesmere Road Golden Valley, MN 55422 Scarborough, Ontario M1P 2V9 Printed in United States www.honeywell.com/bbc ...

Manufacturer Honeywell Category Home Safety Product

Documents that we receive from a manufacturer of a Honeywell R4795A can be divided into several groups. They are, among others:
- Honeywell technical drawings
- R4795A manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell R4795A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell R4795A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell R4795A, service manual, brief instructions and user manuals Honeywell R4795A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell R4795A.

Similar manuals

A complete manual for the device Honeywell R4795A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell R4795A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell R4795A.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell R4795A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell R4795A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell R4795A, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell R4795A - which should help us in our first steps of using Honeywell R4795A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell R4795A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell R4795A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell R4795A?

Use the form below

If you did not solve your problem by using a manual Honeywell R4795A, ask a question using the form below. If a user had a similar problem with Honeywell R4795A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)