Manual Hearth and Home Technologies ST-36TRB-IPI

86 pages 5.84 mb
Download

Go to site of 86

Summary
  • Hearth and Home Technologies ST-36TRB-IPI - page 1

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 1 Models: ST -36TRB-IPI PIER-36TRB-IPI LCOR-36TRB-IPI RCOR-36TRB-IPI • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 2

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _________________ ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 3

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . ? ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 4

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 4  = Contains updated information. 12 Electrical Information A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 B. Intelli fi re Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 52 C. Optio ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 5

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 5 B. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purcha ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 6

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 6 B. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 7

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 7 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous loca- tions such as bathtub enclosures as de fi ned by the Con- sumer Product Safety Commissi ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 8

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 8 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 9

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 9 2 2 Operat ing Instruc tions Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating inst ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 10

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 10 D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. H ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 11

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 1 1 I. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using the transformer . 1. Turn off all electric power t ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 12

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 12 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace of f and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.G. • Clean fi xe ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 13

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 13 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratc ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 14

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 14 V enting Frequency: Seasonally By: Homeowner T ools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow , debris, etc. • V erify term ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 15

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 15 Figure 3.2 IPI Pilot Flame Patterns Burner Ignition and Operation Frequency: Annually By: Quali fi ed Service T echnician T ools needed: Protective gloves, vacuum cleaner , whisk broom, fl ashlight, voltmeter , indexed drill bit set, ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 16

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 16 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure 4.1 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 17

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 17 B. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outsi ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 18

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 18 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate cl ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 19

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 19 C A B D B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase. NOTICE: T reatment of ceiling ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 20

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 20 C A B D Figure 5.3 Clearances to Combustibles PIER-36TRB-IPI G F I I E H * Adjust framing dimensions for interior sheathing (such as sheetrock) PIER-36TRB-IPI AB C D E F G H I DVP Pipe SLP Pipe Rough Opening (Height) DVP Pipe* Rough Op ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 21

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 21 Note: All measurements in inches. MEASUREMENT S FROM TOP EDGE OF T HE OPENING 5 10 11 12 2-1/2 13 14 15 16 17 18 19 32 TO CEILI NG 9 10 11 12 8 7 6 5 4 3 25 18 See-Through Combustible Mantel PIER/LCOR/RCOR Combustible Mantel Note: All m ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 22

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 22 TOP V IEW 3-1/4 in. Min. 2-3/4 in. Min. 1/2 in. Min. Unlimited 1 in. Max. FIREPLACE OPENING Note: Clearance from opening to perpendicular wall. Figure 5.10 Non-Combustible Zone (PIER and ST) Figure 5.9 Combustible Mantel Leg or W all P ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 23

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 23 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 .... ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 24

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 24 O N P R Q V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 6.4 Minimum Clearances for T ermination A = 12 inches................. clearances above grade, ver anda, porch, deck or balcony B = 12 inch ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 25

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 25 B. Continue Adding V ent Components T o Install the Heat Shield: 1. The heat shield is required above the fi rst elbow if the clearance to combustible surface above is between three (3) and four (4) inches. A shield is not required for ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 26

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 26 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies a DVP venting system. Refer to Section 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufac ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 27

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 27 T o replace the fi rst starter elbow with two 45° elbows, refer to Figure 7.3. All other 90° elbows can be replaced with two 45° elbows. General Rules: • A maximum of three 90° elbows (or six 45° elbows) may be used in any vent ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 28

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 28 H 1 V 1 Figure 7.4 Figure 7.5 One Elbow T wo Elbows INST ALLED HORIZONT ALL Y H 1 H 2 V 1 1. T op V ent - Horizontal T ermination - (continued) V 1 Minimum H 1 Maximum Elbow only 1-1/2 ft. 457 mm 6 in. 152 mm 2-1/2 ft. 610 mm 1 ft. 305 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 29

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 29 Figure 7.6 1. T op V ent - Horizontal T ermination - (continued) Three Elbows H 2 H 1 V 2 V 1 V 1 Minimum H 1 Maximum V 2 Minimum H 2 Maximum V 1 + V 2 Minimum H 1 + H 2 Maximum Elbow only 1 ft. 305 mm 6 in. 152 mm 1 ft. 305 mm 6 in. 15 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 30

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 30 Refractory Panel T o access the exhaust opening, remove the refractory panel and exhaust baffle. T o remove refractory panel, remove the two screws on top. To remove the exhaust baffle, remove the three screws securing it. T op V ent A ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 31

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 31 Figure 7.10 4. Center the exhaust restrictor in the open end of the ex- haust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self tapping screws provided in the appliance manual bag. 5. Reinstall the re ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 32

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 32 Figure 7.1 1 T wo Elbows H 1 V 2 V 1 Three Elbows INST ALLED HORIZONT ALL Y H 1 H 2 V 2 V 1 Figure 7.12 V 1 H 1 Maximum V 2 V 1 + V 2 Minimum One Elbow 2-1/2 ft. 762 mm * * * 2 ft. 607 mm 6 ft. 1.8 m * * * 4 ft. 1.2 m 12 ft. 3.7 m * * ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 33

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 33 3. Rear V ent - Horizontal T ermination Figure 7.13 Figure 7.14 No Elbow One 45° Elbow H 1 = 18 in. (406 mm) Maximum H 1 H 1 DO NOT use a 45º elbow in corner installations. Use two 90º elbow instead. ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 34

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 34 INSTALLED HORIZONTALLY H 3 H 2 V 1 H 1 3. Rear V ent - Horizontal T ermination - (continued) T wo Elbows Figure 7.15 Figure 7.16 Three Elbows H 2 V 1 H 1 H 1 Maximum V 1 Minimum H 2 Maximum H 1 + H 2 Maximum 2 ft. 610 mm 6 in. 152 mm 1 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 35

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 35 4. Rear V ent - V ertical T ermination One Elbow Figure 7.17 T wo Elbows Figure 7.18 V 1 H 1 INST ALLED HORIZONT ALL Y H 2 V 2 H 1 V 1 Minimum H 1 Maximum 1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 7 ft. 2.1 m 4 ft. ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 36

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 36 4. Rear V ent - V ertical T ermination - (continued) Three Elbows Figure 7.19 Three Elbows Figure 7.20 INST ALLED HORIZONT ALL Y H 3 H 2 V 1 H 1 V 2 V 1 H 2 H 1 H 1 H 2 H 3 V 1 Minimum H 1 + H 2 + H 3 Maximum *** 8 ft. 2.4 m 4 ft. 1.2 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 37

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 37 A. Pipe Clearances to Combustibles W ARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi restops • Between wall shield fi restops • Around vent system Fa ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 38

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 38 C. V ertical Penetration Framing Figure 8.3 Figure 8.4 Installing the Attic Shield 3 F ASTENERS PER SIDE INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM CEILING FIRESTOP INST ALLED BELOW CEILING CEILING FIR ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 39

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 39 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 40

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 40 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 41

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 41 B. Rear V ent NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. NOTICE: Once the vent cap has been removed it CANNOT be reattached. Figure 9.5 Cut the metal retaining band. Figure 9.6 Remove ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 42

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 42 C. Securing and Leveling the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 43

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 43 1 0 10 Inst all ing V ent P ipe ( D VP and SLP P ipe ) A. Assemble V ent Sections (DVP Pipe Only) Attach V ent to the Firebox Assembly Note: The end of the p ipe secti ons with the lanc ed tabs will f ace toward the applianc e. Attach t ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 44

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 44 B. Assemble V ent Sections (SLP Pipe Only) T o attach the fi rst vent component to the starting collars of the appliance: • Attach an SLP-DVP24 adapter to the starting collar of the appliance. • Lock the vent components into place ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 45

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 45 120º Figure 10.8 Securing V ertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble V ent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 46

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 46 F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a fl at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the fi restop. • Seal the gap be ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 47

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 47 G. Install Metal Roof Flashing Note : Skip this section if using the RF4-8. • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 48

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 48 I. Install RF4-8 The RF4-8 may be used in place of the roof fl ashing and storm collar (Sections 10.G. and 10.H.) Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flash ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 49

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 49 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.23 Figure 10.23 TERMINA TION CAP J. Install V ertical T ermination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 50

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 50 Cap Speci fi cation Chart (depth without using additional pipe sections) 36 inch Multisided Series DVP-TRAPK1 T op Vent Depth DVP-TRAP1 Rear V ent Depth DVP-TRAPK2 T op Vent Depth DVP-TRAP2 Rear V ent Depth 2-7/8 in to 4-3/4 in 3-1/8 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 51

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 51 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 52

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 52 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 53

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 53 Figure 12.1 Intelli fi re Ignition Wiring Diagram with Wall Switch or Thermostat Figure 12.2 Intelli fi re Ignition Wiring Diagram with Remote Receiver NOTE: 1 . Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 V ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 54

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 54 F . W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.5): • The power supply for the appliance must be brought into a switch box. • The power can then ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 55

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 55 1 3 13 Fi nishing A. Splatter Guard The splatter guard is a piece of corrugated material used to protect the appliance during the installation process be- fore fi nishing work on the whole hearth is complete. Splatter guards must be re ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 56

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 56 Step 5. Fold bottom fl ap along score line as indicated in Figure 13.6 and tuck into valve access area of appliance. Splatter guard should fi t securely on front of unit. Once plumbing and wiring are complete on the fi replace, the ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 57

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 57 Note: All measurements in inches. MEASUREMENT S FROM TOP EDGE OF T HE OPENING 5 10 11 12 2-1/2 13 14 15 16 17 18 19 32 TO CEILI NG 9 10 11 12 8 7 6 5 4 3 25 18 See-Through Mantel Projection PIER/LCOR/RCOR Mantel Projection Note: All mea ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 58

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 58 Figure 13.16 Combustible Mantel Leg or W all Projections (Acceptable on both sides of opening) TOP VIEW 3-1/4 in. Min. 2-3/4 in. Min. 1/2 in. Min. Unlimited 1 in. Max. FIREPLACE OPENING Note: Clearance from opening to perpendicular wal ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 59

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 59 Figure 13.20 Inside fi t door Figure 13.21 Operable hinge door DOOR FINISHING MA TERIAL FINISHING MA TERIAL (Outside door width) (Includes 1/8 in. opening each side of door) 37 in. 37-1/4 in. Finishing materials over 1 inch thick. Fini ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 60

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 60 E. Elevated Hearth Systems Use the table below to identify the hearth system that will be used. The table will also help identify ef fects on the various dimensions. Some hearth systems will elevate the appliance off the fl oor at a g ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 61

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 61 A. Remove Fixed Glass Assembly See Section 14G. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 62

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 62 F . Install the Log Assembly Figure 2. Factory Installed Logs Figure 2. Factory Installed Logs F F igure 1. Log Assembly Location igure 1. Log Assembly Location CAUTION: DO NOT reposition logs that have been factory installed! Follow t ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 63

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 63 F F igure 5. Placement of Log #2 igure 5. Placement of Log #2 2 2 F F igure 7. Placement of Log #3 igure 7. Placement of Log #3 3 3 2 2 INDENT A TIONS INDENT A TIONS STEP 3. Log #2 (SR V2128-705): The Y -shaped end of log #2 should rest ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 64

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 64 I. Air Shutter Setting This appliance has an adjustable air shutter (which con- trols the primary air) factory set for the minimum vertical vent run (see Figure 12.15). If your installation has more than the minimum required vertical v ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 65

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 65 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed technician ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 66

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 66 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 67

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 67 1 6 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.1 See-Through Dimensions B C FRONT VIEW RI ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 68

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 68 Figure 16.2 Pier Dimensions B C FRONT VIEW RIGHT VIEW LEFT VIEW A P L Ø K D M O N E ELECTRICAL ACCESS GAS LINE ACCESS J Ø K F G H i Location Inches Millimeters I 1-1/2 38 J 27 686 K 8 203 L 12 305 M 9-1/2 241 N 38 965 O 34-5/8 880 P ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 69

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 69 Figure 16.3 LCOR, RCOR Dimensions B C FRONT VIEW RIGHT VIEW ELECTRICAL ACCESS GAS LINE ACCESS LEFT VIEW A J Ø K L Ø K D F G H M P N i O E Location Inches Millimeters I 1-1/2 38 J 27 686 K 8 203 L 12 305 M 9-1/2 241 N 24-1/2 622 O 38 9 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 70

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 70 B. V ent Components Diagrams Figure 16.4 DVP vent components 10-1/2 in. (267 mm) 10-7/8 in. (276 mm) 45 ° 7-3/8 in. (187 mm) 11-3/8 in. (289 mm) 1-1/4 in. (32 mm) 9-1/4 in. (235 mm) 13-1/4 in. (337 mm) 1/2 in. TYP DVP90ST (90° Elbow) ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 71

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 71 DVP-HPC1 DVP-HPC2 DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 72

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 72 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK Trap Ca p Brick Extension 13-3/4 in. (349 mm) 5 in. (127 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 73

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 73 DVP-TB1 BasementVent Cap 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 10-1/2 in. (267 mm) 3-7/8 in. (98 mm) DVP-TV VerticalTermination Cap 7-1/4 in. 12 in. 305 mm (184 mm) 5-1/4 in. (133 mm) 1 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 74

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 74 B. V ent Components Diagrams (continued) Figure 16.8 DVP vent components 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) DVP-HRC-SS ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 75

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 75 B. V ent Components Diagrams (continued) Figure 16.9 SLP Series V ent Components EFFECTIVE HEIGHT/ LENGTH 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in. 251 mm 6-1/2 in. 165 m ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 76

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 76 SLK-SNKD Snorkel T ermination Cap SLP-TVHW V ertical T ermination Cap SLP-FLEX-TRAP Horizontal T ermination Kit SLP-CCS-BK Cathedral Ceiling Support Box-Black SLP-DCF-BK Ceiling Firestop Black SLP-WT -BK W all Thimble-Black B. V ent Co ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 77

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 77 C. Service Parts Part number list on following page. ST -36TRB-IPI Beginning Manufacturing Date: Nov . 2008 Ending Manufacturing Date:______ Service Parts Diagram Log Set Assembly A 1 C 2 D 3 B 4 5 6 7 8 9 10 11 12 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 78

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 78 C. Service Parts List ST -36TRB-IPI IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordere ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 79

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 79 C. Service Parts Part number list on following page. PIER-36TRB-IPI Service Parts Diagram 4 5 6 7 8 9 10 11 12 13 14 Beginning Manufacturing Date: Nov . 2008 Ending Manufacturing Date: ______ Log Set Assembly A 1 C 2 D 3 B ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 80

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 80 C. Service Parts List PIER-36TRB-IPI IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be order ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 81

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 81 C. Service Parts Part number list on following page. LCOR-36TRB-IPI Service Parts Diagram Beginning Manufacturing Date: Nov . 2008 Ending Manufacturing Date:______ Log Set Assembly A 1 C 2 D 3 B 4 5 6 7 8 9 10 11 12 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 82

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 82 C. Service Parts List LCOR-36TRB-IPI IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be order ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 83

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 83 C. Service Parts Part number list on following page. RCOR-36TRB-IPI Service Parts Diagram Beginning Manufacturing Date: Nov . 2008 Ending Manufacturing Date: ______ Log Set Assembly A 1 C 2 D 3 B 4 5 6 7 8 9 10 11 12 13 14 ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 84

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 84 C. Service Parts List RCOR-36TRB-IPI IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be order ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 85

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 85 Intermittent Pilot Ignition V alve Assembly Service Parts ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI V alve Assembly Diagram/ Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement ...

  • Hearth and Home Technologies ST-36TRB-IPI - page 86

    Heat & Glo • ST -36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev . B • 10/08 86 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .heatnglo.com D. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the ...

Manufacturer Hearth and Home Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Hearth and Home Technologies ST-36TRB-IPI can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- ST-36TRB-IPI manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies ST-36TRB-IPI
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies ST-36TRB-IPI.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies ST-36TRB-IPI, service manual, brief instructions and user manuals Hearth and Home Technologies ST-36TRB-IPI. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies ST-36TRB-IPI.

A complete manual for the device Hearth and Home Technologies ST-36TRB-IPI, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies ST-36TRB-IPI by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies ST-36TRB-IPI.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies ST-36TRB-IPI - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies ST-36TRB-IPI, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies ST-36TRB-IPI, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies ST-36TRB-IPI - which should help us in our first steps of using Hearth and Home Technologies ST-36TRB-IPI
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies ST-36TRB-IPI
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies ST-36TRB-IPI in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies ST-36TRB-IPI?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies ST-36TRB-IPI, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies ST-36TRB-IPI it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)