English dropdown-ico

Manual Homelite UT74020

32 pages 0.44 mb
Download

Go to site of 32

Summary
  • Homelite UT74020 - page 1

    Chain Saw / Scie De Chaine / Motosierra OPERA TOR'S MANU AL MANUEL DU PROPRIÉT AIRE MANU AL P ARA EL OPERADOR PS 06162 7-02 Ranger™ 33cc 16" UT74020 Homelite Consumer Products, Inc. 1428 Pearman Dairy Road Anderson, SC 29625 ...

  • Homelite UT74020 - page 2

    2 W ARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm. CALIFORNIA PROPOSITION 65 MISE EN GARDE Les gaz d'échappement du moteur de cet appareil contiennent des substances chimiques considérées par l'État de la Californie comme étan ...

  • Homelite UT74020 - page 3

    3 KICKBACK WARNING KICKBACK occurs when the moving chain contacts an object at the upper portion of the tip of the guide bar or when the wood closes in and pinches the saw chain in the cut. Contact at the upper portion of the tip of the guide bar can cause the chain to dig into the object and stop the chain for an instant. The result is a lightning ...

  • Homelite UT74020 - page 4

    4 • Asegúrese de que el área en que esté cortando se encuentre libre de obstrucciones. No deje que el borde de la barra de guía entre en contacto con leños, ramas, cercas o cualquier otro tipo de obstrucción que se pueda golpear mientras usted esté operando su sierra. • Mantenga la protección del borde anti-retroceso SAFE-T-TIP ® debid ...

  • Homelite UT74020 - page 5

    5 RECOMMENDED BAR AND CHAIN COMBINATIONS COMBINAISONS RECOMMANDÉES DE GUIDE-CHAÎNE ET DE CHAÎNE COMBINACIONES RECOMENDADAS DE BARRAS Y CADENAS TO MAINTAIN EASY STARTING AND CUTTING PERFORMANCE Before storing your chain saw for more than 30 days, drain all fuel from tank into a container approved for gasoline. Run engine until it stops. This will ...

  • Homelite UT74020 - page 6

    6 A. Front hand guard /Chain Brake B. Front handlebar C. Cylinder cover D. Throttle lock button for starting E. Trigger lock F. Rear handle G . Throttle trigger H. Ignition Switch (I) On / (O) Off I. Fuel mix cap J . Chain oil cap K. Starter/Fan housing L. Starter grip M. Safe-t-tip ® N. Primer bulb O. C hoke lever A. Protège-main avant / Frein d ...

  • Homelite UT74020 - page 7

    7 NOTE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and wrists of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as num ...

  • Homelite UT74020 - page 8

    8 • Always use caution when handling fuel. Move the chain saw at least 10 feet (3m) from the fueling point before starting the engine. • Do not operate a chain saw with one hand! Serious injury to the operator, helpers, by- standers, or any combination of these per- sons may result from one-handed operation. A chain saw is intended for two-hand ...

  • Homelite UT74020 - page 9

    9 MAINTENANCE • Never operate a chain saw that is damaged, improperly adjusted, or is not completely and securely assembled. Be sure that the saw chain stops moving when the throttle control trigger is released. • All chain saw service, other than items in the Owner's Manual maintenance instructions, should be performed by competent chain ...

  • Homelite UT74020 - page 10

    10 FRONT HAND GUARD Your saw has a factory-installed front hand guard to prevent contact with the chain if your hand slips off the front handle. Do not remove the front hand guard. Maintain the guard in good condi- tion and do not use the guard as a hand grip. Replace it if damaged or broken. THE OWNER'S MANUAL Your owner's manual is for ...

  • Homelite UT74020 - page 11

    11 CHAÎNE À FAIBLE REBOND Les limiteurs de profondeur à l’avant de chaque dent peuvent réduire au minimum la force d’une réaction de rebond en évitant que les dents ne s’encastrent trop au niveau de la zone de rebond. N’utiliser comme pièce de rechange qu’une chaîne équivalente à la chaîne d’origine ou une chaîne certifiée ...

  • Homelite UT74020 - page 12

    12 GUIDE BAR AND CHAIN ASSEMBLY DANGER Never start your engine unless guide bar, chain, drivecase cover and clutch drum are installed. Without all these parts in place, the clutch can fly off or explode. 1. Always put the switch to "O" stop before you do any work on the saw. 2. Remove the mounting nuts ( A ) (5/8" wrench required), d ...

  • Homelite UT74020 - page 13

    13 CHAIN TENSION 1. Stop the engine before setting tension. Turn the adjusting screw ( I ) clockwise to move the guide bar outward until the chain is tight to the bar but can still be pulled around the bar by hand. See Illustration A. Tighten guide bar nut(s) securely to lock in position. 2. Chain must be re-tensioned whenever the drive link tangs ...

  • Homelite UT74020 - page 14

    14 DISPOSITIF DE LUBRIFICATION DE LA CHAÎNE CHAIN OIL SYSTEM 1. Use HOMELITE ® Bar and Chain Oil. It is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. If not available, use any new SAE-30 weight engine oil. NOTE: Used, dirty or otherwise contami- nated oils must not be us ...

  • Homelite UT74020 - page 15

    15 DÉMARRAGE ET ARRÊT DE L’APPAREIL REMARQUE Ne pas oublier que la tronçonneuse perd un peu de fluide pendant le transport et l’entreposage, en particulier, de l’huile de lubrification de chaîne. Ne pas la placer sur une surface que l’on désire garder propre. Suivre les étapes 1 à 10 pour le démarrage d’un moteur froid. 1. Appuyer ...

  • Homelite UT74020 - page 16

    16 9. Pull starter until engine tries to run. (No more than 6 pulls.) 10. Move choke lever to half choke position ( G ) and pull starter until engine runs. 11. Move choke lever to run position ( H ). Squeeze the trigger and then release. This unlatches the trigger and gives you control of throttle for cutting. 12. Now you are ready to pick up the s ...

  • Homelite UT74020 - page 17

    17 PRÉPARATIFS POUR L’OPÉRATION DE COUPE TENUE CORRECTE DES POIGNÉES 1. Porter des gants antidérapants afin de bénéficier d’une meilleure prise et d’une meilleure protec- tion. 2. Tenir correctement l’appareil ( A ) lorsque le moteur fonctionne. Les doigts doivent faire le tour de la poignée et le pouce doit être enroulé sous la po ...

  • Homelite UT74020 - page 18

    18 POSITION CORRECTE DU CORPS POUR LA COUPE • Le poids du corps doit être réparti également sur les deux pieds, les pieds reposant sur un sol ferme. • Bloquer le coude dans la position bras tendu ( A ) afin de pouvoir résister à la force d’une réaction de rebond. • Le corps doit toujours se trouver sur la gauche du plan de la chaîne ...

  • Homelite UT74020 - page 19

    19 WORK AREA PRECAUTIONS • Cut only wood or materials made from wood; no sheet metal, no plastics, no masonry, no non-wood building materials. • Never allow children to operate your saw. Allow no person to use this chain saw who has not read this Owner's Manual or received adequate instructions for the safe and proper use of this chain saw ...

  • Homelite UT74020 - page 20

    20 UNUSUAL HAZARDOUS CONDITIONS • Do not fell trees during periods of high wind or heavy precipitation. Wait to do your cutting until the hazard has ended. • Do not cut down trees having an extreme lean or large trees that have rotten limbs, loose bark, or hollow trunks. Have these trees pushed or dragged down with power equipment. Then you can ...

  • Homelite UT74020 - page 21

    21 3. Cut a notch ( C ) about 1/3 the diameter of the trunk in the side of the tree. Make the cuts of the notch so they intersect at a right angle to the line of fall . See Illustration 5. This notch should be cleaned out to leave a straight line. To keep the weight of the wood off the saw, always make the lower cut of the notch before the upper cu ...

  • Homelite UT74020 - page 22

    22 LOAD A LOAD B A B During bucking operations always stand on the uphill side so that the cut-off section of the log can not roll over you. A wedge can be used on large diameter logs to hold the cut open (See illustration). Pendant le tronçonnage sur un terrain en pente, toujours se placer en amont pour éviter d’être heurté au cas où la sec ...

  • Homelite UT74020 - page 23

    23 LIMBING AND PRUNING • Work slowly, keeping both hands on the saw with a firm grip. Maintain secure footing and balance. • Keep the tree between you and the chain while limbing ( A ). Cut from the side of the tree opposite the branch you are cutting. • Do not cut from a ladder, this is extremely dangerous. Leave this operation for profes- s ...

  • Homelite UT74020 - page 24

    24 D B C A ENTRETIEN DE LA CHAÎNE ET DU GUIDE-CHAÎNE N’utiliser sur cette tronçonneuse que des chaînes HOMELITE ® à faible rebond. Ces chaînes permettent une coupe rapide et réduisent la tendance au rebond lorsqu’elles sont entretenues correctement. La chaîne doit être correctement entretenue pour maintenir une coupe rapide et réguli ...

  • Homelite UT74020 - page 25

    25 HOW TO FILE THE CUTTERS Be careful to file all cutters to the specified angles and to the same length, as fast cutting can be obtained only when all cutters are uniform. 1. Clamp the middle of the guide bar in a vice. Be careful that you do not pinch the guide bar rails or the chain will not move freely in the groove. 2. Tighten the chain tensio ...

  • Homelite UT74020 - page 26

    26 RAKER (DEPTH GAUGE) CLEARANCE 1. The rakers ( D, see page 24 ) should be maintained at a clearance ( A, see page 24 ) between .020" (0.5 mm) and .018 (0.46 mm). Depth gauge tool #D06885 can be used for checking the raker clearances. 2. Every time the chain is filed, check the raker clearance. Use a Flat File and a Depth Gauge Jointer to low ...

  • Homelite UT74020 - page 27

    27 REGULAR MAINTENANCE AIR FILTER MAINTENANCE For proper performance and long life, keep air filter clean. TO INSPECT AND CLEAN OR REPLACE THE AIR FILTER NOTE Always clean the air filter before making any mixture adjustments of the carburetor. 1. For access to the cylinder and carburetor area, loosen the three screws holding the cylinder cover and ...

  • Homelite UT74020 - page 28

    28 SPARK ARRESTOR 1. Always keep the muffler ( A ) and spark arrestor ( B ) on your saw in good condition. A faulty spark arrestor screen can create a fire hazard. 2. The spark arrestor screen is retained by the deflector ( C ). Remove the deflector screw ( D ) to access screen. 3. Replace the spark arrestor screen if it is cracked or otherwise det ...

  • Homelite UT74020 - page 29

    29 HOMELITE® PRODUCTS - LIMITED WARRANTY Homelite Consumer Products, Inc. warrants to the original retail purchaser that this Homelite® Product is free from defects in material and workmanship and agrees to repair or replace, at Homelite Consumer Products, Inc.'s discretion, any defective Product free of charge within these time periods from ...

  • Homelite UT74020 - page 30

    30 PRODUIT HOMELITE® - GARANTIE LIMITÉE HomeliteConsumer Products, Inc. garantit à l’acquéreur original (vente au détail) que ce produit Homelite® ne présente pas de défauts de matière ou de main d’oeuvre, et s’engage à réparer ou à remplacer (à la discrétion de Homelite Consumer Products, Inc.) gratuitement tout produit défect ...

  • Homelite UT74020 - page 31

    31 PRODUCTOS HOMELITE® - GARANTIA LIMITADA La Homelite Consumer Products, Inc. le garantiza al comprador original al por menor que este Producto Homelite® se encuentra libre de defectos de material y mano de obra, y acepta reparar o reemplazar, a discreción de Homelite Consumer Products, Inc.'s cualesquiera productos defectuosos sin ningún ...

  • Homelite UT74020 - page 32

    For product information, technical help, dealer locations or parts ordering information visit our website at: www .homelite.com . P our des renseignements sur les produits, une aide technique , l’adresse des détaillants ou des renseignements sur la f açon de commander des pièces, visitez notre site w eb au www .homelite.com . Para obtener info ...

Manufacturer Homelite Category Chainsaw

Documents that we receive from a manufacturer of a Homelite UT74020 can be divided into several groups. They are, among others:
- Homelite technical drawings
- UT74020 manuals
- Homelite product data sheets
- information booklets
- or energy labels Homelite UT74020
All of them are important, but the most important information from the point of view of use of the device are in the user manual Homelite UT74020.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Homelite UT74020, service manual, brief instructions and user manuals Homelite UT74020. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Homelite UT74020.

Similar manuals

A complete manual for the device Homelite UT74020, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Homelite UT74020 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Homelite UT74020.

A complete Homelite manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Homelite UT74020 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Homelite UT74020, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Homelite UT74020, that we can find in the current document
3. Tips how to use the basic functions of the device Homelite UT74020 - which should help us in our first steps of using Homelite UT74020
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Homelite UT74020
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Homelite UT74020 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Homelite UT74020?

Use the form below

If you did not solve your problem by using a manual Homelite UT74020, ask a question using the form below. If a user had a similar problem with Homelite UT74020 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)