Manual Echo PPT-2400

40 pages 1.31 mb
Download

Go to site of 40

Summary
  • Echo PPT-2400 - page 1

    P OWER P RUNER O PERA TO R ' S M ANUAL 1 Power Pruner Operator's Manual MODELS: PPT-2100 TYPE 1/1E Serial Number 503550 - 506999 PPT-2400 TYPE 1/1E Serial Number 505900 - 518599 W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual, which must be read and understood for proper an ...

  • Echo PPT-2400 - page 2

    2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the- job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages. W ARNING DANGER Read rules for saf ...

  • Echo PPT-2400 - page 3

    P OWER P RUNER O PERA TO R ' S M ANUAL 3 This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. The circle with the slash symbol means whatever is shown within the circle is prohibited. M ANUAL S AFETY S YMBOLS & I MPORT ANT I NFORM ...

  • Echo PPT-2400 - page 4

    4 DECALS Locate this safety decal on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructio ...

  • Echo PPT-2400 - page 5

    P OWER P RUNER O PERA TO R ' S M ANUAL 5 Guide Bar and Saw Chain W ARNING DANGER • Serious injury may result from the use of non approved guide bar and saw chain combinations. Read and comply with all safety instructions listed in this manual. • ECHO, INC. will not be responsible for the failure of cutting devices or accessories which have ...

  • Echo PPT-2400 - page 6

    6 PERSONAL CONDITION & SAFETY EQUIPMENT W ARNING DANGER Power Pruner users risk injury to themselves and others if the Power Pruner is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a Power Pruner. Physical Condition -- Your judgment and physical dexterity may not be good: ...

  • Echo PPT-2400 - page 7

    P OWER P RUNER O PERA TO R ' S M ANUAL 7 SAFE OPERA TION W ARNING DANGER All over head electrical conductors and communications wires can have electricity flow with high voltages. Never touch wires directly or indirectly when pruning, otherwise serious injury or death may result. Hot Humid Weather -- Heavy protective clothing can increase oper ...

  • Echo PPT-2400 - page 8

    8 Keep A Firm Grip • Grip Power Pruner with both hands with thumbs and fingers tightly encircling the handle, and lower shaft tube. Keep A Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not overreach. • Operate the Power Pruner onl ...

  • Echo PPT-2400 - page 9

    P OWER P RUNER O PERA TO R ' S M ANUAL 9 EXTENDED OPERA TION / EXTREME CONDITIONS Vibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations fol ...

  • Echo PPT-2400 - page 10

    10 D ESCRIPTION Due to packaging restriction the ECHO product you have purchased requires some assembly. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. CONTENTS LIST __ Power Head __ Shaft Tube Assembly __ Cutting Attachment W ...

  • Echo PPT-2400 - page 11

    P OWER P RUNER O PERA TO R ' S M ANUAL 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 ...

  • Echo PPT-2400 - page 12

    12 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Starter. 2. REAR HANDLE ASSEMBLY - Sturdy handle for right hand placement. Includes stop switch and throttle trigger. 3. THROTTLE TRIGGER LOCKOUT - This lever must be depressed before throttle trigger can be operated. 4. STOP SWITCH - Mounted on top of handle assembly. ...

  • Echo PPT-2400 - page 13

    P OWER P RUNER O PERA TO R ' S M ANUAL 13 MODEL PPT-2100 PPT-2400 Length (Standard) 2286 mm (90.0 in.) 2743 mm (108.0 in.) Length (Extended) 3410 mm (134.25 in.) 3886 mm (153.0 in.) Width 222 mm (8.75 in.) 222 mm (8.75 in.) Height 229 mm (9.0 in.) 229 mm (9.0 in.) Weight (dry) 7.4 kg (16.3 lb.) 7.7 kg (16.9 lb.) Engine Type Air cooled, two-str ...

  • Echo PPT-2400 - page 14

    14 1 . Loosen bolt (A). 2 . Match square socket in engine shaft with square power transmis- sion shaft (B) and slide together until engine rests against the machine surface of lower shaft tube housing coupler (C). 3 . Rotate lower shaft tube housing to align engine and rear handle assembly in an upright position. 4 . Tighten bolt (A) securely so en ...

  • Echo PPT-2400 - page 15

    P OWER P RUNER O PERA TO R ' S M ANUAL 15 2 . Loosen center clamp knob (F) turning counter clockwise. 3 . Pull upper shaft tube (G) out of fiberglass lower shaft tube 127-152 mm (5-6 in.), then slide (G) back into fiberglass lower shaft tube exposing inner power transmission shaft (H). Align and join star shaped drive end of inner power transm ...

  • Echo PPT-2400 - page 16

    16 B A 4 . Tighten the 10mm linkage nuts (E). 5 . Check throttle for freedom of movement and make sure it returns to idle position. If the throttle linkage does not allow the carburetor throttle plate (C) to return to idle against idle screw (D), loosen linkage nuts; turn throttle linkage nut (E) counter clockwise until throttle plate (C) rests aga ...

  • Echo PPT-2400 - page 17

    P OWER P RUNER O PERA TO R ' S M ANUAL 17 P RE -O PERA TION FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] gasoline or gasohol known to be good quality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methanol (wood alcohol) is NOT approved. Two-Stroke Oil - A two-stroke en ...

  • Echo PPT-2400 - page 18

    18 SM T W T F S 1234 5 6 7 8 9 10 1 1 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel con- tainer thoroughly before each use. AUTO ...

  • Echo PPT-2400 - page 19

    P OWER P RUNER O PERA TO R ' S M ANUAL 19 DETERMINE OPERA TION AREA • Before starting the unit, equip yourself and fellow workers in the 15 M (50 ft.) safety zone with the required protective equipment and clothing. • Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions such as overhead electrical line ...

  • Echo PPT-2400 - page 20

    20 W ARNING DANGER Inspect starting area for hazards such as rocks, glass, debris etc. which could be contacted by the cutting attachment when starting. Keep helpers and bystanders at least 15 M (50 ft.) from starting area, otherwise serious personal injury may result. 4 . Lay the pruner on a flat clear area. Firmly grasp rear handle grip and throt ...

  • Echo PPT-2400 - page 21

    P OWER P RUNER O PERA TO R ' S M ANUAL 21 STOPPING ENGINE 1 . Release Throttle. Allow engine to idle for a minute. 2 . Stop Switch - Stop. Move stop switch button (A) backward to STOP position. W ARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO ...

  • Echo PPT-2400 - page 22

    2 2 MAINTENANCE INTER V ALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O M 0 9 R O S R U O H 6 S H T N O M 0 7 2 R O S R U O H Y L R A E Y 0 0 6 S R U O H s e r u d e c o r P e c n a n e t n i a M r e l a e D o h c E d e d ...

  • Echo PPT-2400 - page 23

    P OWER P RUNER O PERA TO R ' S M ANUAL 23 AIR FIL TER Level 1. Parts required: 90008 REPOWER FILTER KIT 1 . Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu- lated dirt from the air cleaner area. 2 . Remove the air cleaner cover. Clean and inspect the element ...

  • Echo PPT-2400 - page 24

    24 SP ARK PLUG Level 2. Parts Required: Spark Plug, NGK BPM-7A (15901010630 - PPT-2100) NGK BPM-7Y (15901019630 - PPT-2400) 1 . Remove spark plug and check for fouling, worn and rounded center electrode. 2 . Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3 . Adjust spark plug gap by bending ...

  • Echo PPT-2400 - page 25

    P OWER P RUNER O PERA TO R ' S M ANUAL 25 1 . Remove spark plug lead from spark plug and throttle linkage end from the carburetor swivel. 2 . Remove the four screws that retain the engine cover (A). Two at the top of the recoil starter, two on either side of the front. Lift the cover from the engine and lay to the front of the power pruner. NO ...

  • Echo PPT-2400 - page 26

    26 CARBURETOR ADJUSTMENT Emission Models Level 2. Parts required: None. 1 . Before adjusting the carburetor, clean or replace the air filter and spark arrester screen. 2 . Start engine and run for several minutes to reach operating temperature. 3 . Stop engine. Turn HI (A) speed needle CCW (counter clockwise) to stop. Turn LO (B) speed needle midwa ...

  • Echo PPT-2400 - page 27

    P OWER P RUNER O PERA TO R ' S M ANUAL 27 W ARNING DANGER When carburetor adjust ment is completed, cutting attachment should not move at idle, otherwise serious personal injury may result. CARBURETOR ADJUSTMENT Non Emissions Models NOTE If carburetor has limiter caps follow "Carburetor Adjustment" procedures for Emission models on p ...

  • Echo PPT-2400 - page 28

    28 GUIDE BAR AND SA W CHAIN REPLACEMENT W ARNING DANGER Never try to replace or adjust guide bar and saw chain with engine running. This saw chain is VERY sharp, wear heavy gloves to protect your hands when handling it. Wear eye protection meeting CE or ANSI Z87.1 specification. Guide Bar Replacement / Installation Level 3 • Loosen two (2) 11mm ( ...

  • Echo PPT-2400 - page 29

    P OWER P RUNER O PERA TO R ' S M ANUAL 29 FILING SA W CHAIN Level 3. IMPORTANT Dull or damaged cutters will result in poor cutting performance, increased vibration and premature saw chain failure. W ARNING DANGER Always stop engine and wear gloves when filing saw chain, otherwise serious personal injury may result. 1 . Set round file (A) in cu ...

  • Echo PPT-2400 - page 30

    30 T ROUBLESHOOTING Remedy Muffler wet with fuel Engine does not crank No fuel at cylinder Spark at end of plug wire No spark at end of plug wire Spark at plug No spark at plug Engine Cranks Fuel at carburetor No fuel at carburetor Open choke Clean/replace air filter Adjust carburetor See your Echo dealer Stop switch off Electrical problem Interloc ...

  • Echo PPT-2400 - page 31

    P OWER P RUNER O PERA TO R ' S M ANUAL 31 S TORAGE Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1 . Store unit in a dry, dust free place, out of the reach of children. W ARNING DANGER Do not store in enc ...

  • Echo PPT-2400 - page 32

    32 ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 DEALER? Call 1-800-432-ECHO ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders SERVICE Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Servi ...

  • Echo PPT-2400 - page 33

    SUPPLEMENT T O OPERA TOR'S MANUAL P ART NUMBER 89865024661 (X7502301401) FOR MODELS: PPT-2100 S/N 507000 & UP PPT-2400 S/N 518000 & UP CUTTING ATTACHMENT INSTALLATION INSTRUCTIONS The enclosed pages include important assembly and adjustment procedures for your new Power Pruner. Please replace original pages 10, 13 - 16, 18, and 29 in t ...

  • Echo PPT-2400 - page 34

    10A D ESCRIPTION Due to packaging restriction the ECHO product you have purchased requires some assembly. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. CONTENTS LIST __ Power Head __ Shaft Tube Assembly __ Cutting Attachment ...

  • Echo PPT-2400 - page 35

    P OWER P RUNER O PERA TOR ' S M ANUAL 13A S PECIFICA TIONS Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment. M O D E L P ...

  • Echo PPT-2400 - page 36

    14A 1 . Loosen bolt (A). 2 . Match square socket in engine shaft with square power transmis- sion shaft (B) and slide together until engine rests against the machine surface of lower shaft tube housing coupler (C). 3 . Rotate lower shaft tube housing to align engine and rear handle assembly in an upright position. 4 . Tighten bolt (A) securely so e ...

  • Echo PPT-2400 - page 37

    P OWER P RUNER O PERA TOR ' S M ANUAL 15A 2 . Loosen center clamp knob (F) turning counter clockwise. 3 . Pull upper shaft tube (G) out of fiberglass lower shaft tube 127-152 mm (5-6 in.), then slide (G) back into fiberglass lower shaft tube exposing inner power transmission shaft (H). Align and join star shaped drive end of inner power transm ...

  • Echo PPT-2400 - page 38

    16A 4 . Tighten the 10mm linkage nuts (E). 5 . Check throttle for freedom of movement and make sure it returns to idle position. If the throttle linkage does not allow the carburetor throttle plate (C) to return to idle against idle screw (D), loosen linkage nuts; turn throttle linkage nut (E) counter clockwise until throttle plate (C) rests agains ...

  • Echo PPT-2400 - page 39

    18A Automatic Oiling System 1 . W ipe debris from around oil fill cap. 2 . Remove oil fill cap and fill reservoir with a quality , low viscosity guide bar and saw chain oil. NOTE The discharge volume of the automatic oiler is preset to deliver 3 to 4 cc/min. at normal operating RPM. During heavy or dry cutting conditions the oil discharge volume ma ...

  • Echo PPT-2400 - page 40

    P OWER P RUNER O PERA TOR ' S M ANUAL 29A A B GUIDE BAR AND SA W CHAIN REPLACEMENT W ARNING DANGER Never try to replace or adjust guide bar and saw chain with engine running. This saw chain is VERY sharp, wear heavy gloves to protect your hands when handling it. Wear eye protection meeting CE or ANSI Z87.1 specification. Guide Bar Replacement ...

Manufacturer Echo Category Planer

Documents that we receive from a manufacturer of a Echo PPT-2400 can be divided into several groups. They are, among others:
- Echo technical drawings
- PPT-2400 manuals
- Echo product data sheets
- information booklets
- or energy labels Echo PPT-2400
All of them are important, but the most important information from the point of view of use of the device are in the user manual Echo PPT-2400.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Echo PPT-2400, service manual, brief instructions and user manuals Echo PPT-2400. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Echo PPT-2400.

Similar manuals

A complete manual for the device Echo PPT-2400, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Echo PPT-2400 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Echo PPT-2400.

A complete Echo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Echo PPT-2400 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Echo PPT-2400, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Echo PPT-2400, that we can find in the current document
3. Tips how to use the basic functions of the device Echo PPT-2400 - which should help us in our first steps of using Echo PPT-2400
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Echo PPT-2400
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Echo PPT-2400 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Echo PPT-2400?

Use the form below

If you did not solve your problem by using a manual Echo PPT-2400, ask a question using the form below. If a user had a similar problem with Echo PPT-2400 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (1)

Romeo

Non trovo il manuale in italiano per sistemare il flessibile interno che sta girando a vuoto. Ci sono dei piccoli prezzi di plastica nera penso siano rotti. Grazie