Manual Honeywell HMR4007

8 pages 0.41 mb
Download

Go to site of 8

Summary
  • Honeywell HMR4007 - page 1

    HMR4007 SENSOR PRODUCTS HMR4007 Linear Position Sensor User’s Guide Solid State Electronics Center • www .magne ticsensors.com • (800) 323-8295 • Page 1 ...

  • Honeywell HMR4007 - page 2

    HMR4007 SENSOR PRODUCTS INTRODUCTION The Honeywell HMR4007 is an electronic linear p osition sensing solution for u se in commercial and industrial application environments. A stationary array of Hone ywell’s magnetoresistive (MR) sensors is utilized to quickly and accurately monitor the position of a small magnet attached to a moving object such ...

  • Honeywell HMR4007 - page 3

    HMR4007 SENSOR PRODUCTS SPECIFICATIONS Characteristics Conditions Min Typ Max Units General Accuracy 0.2 0.1 mm Resolution 0.1 mm Hysteresis 0.01 mm Repeatability 0.01 0.1 mm Update Rate 10 30 Hz Standoff Distance (gap) between the target magnet and the sensor board 0.1 5 (note 1) mm Magnetic Field Range magnetic field at the sensor array 80 (note ...

  • Honeywell HMR4007 - page 4

    HMR4007 SENSOR PRODUCTS PIN CONFIGURATION Pin Number Pin Name Description Digital Interface 1 RTS Serial Clock Output 2 Data_Out Serial Data Output 3 Data_In Serial Data Input 4 CTS Serial Clock Input 5 Power Unregulated Power Input (+6 to +28 VDC) (see note 1) 6 GND Power and Signal Ground Analog Interface 1 Power Unregulated Power Input (+6 to +2 ...

  • Honeywell HMR4007 - page 5

    HMR4007 SENSOR PRODUCTS PHYSICAL CHARACTERISTICS The circuit board for the HMR4007 Linear Position Sensor is approximately 340mm by 8 0mm. A 6-pin right angle connector (J1) and two 4-pin connectors (J2, J3) protrud e from the back of the b oard for user conne ctions. Components on the top-side have a maximum height of 12mm. Figure 1 shows a t ypic ...

  • Honeywell HMR4007 - page 6

    HMR4007 SENSOR PRODUCTS APPLICATION NOTES USING THE HMR4007 AS A STAND ALONE SENSOR Introduction The HMR4007 can be used as a stand-alone sensor without th e need for any digital communications. The bo ard is configured at the factory t o provide a 0-2.5 VDC analog output (axial magnet) and statu s signal that represents the position of the magnet ...

  • Honeywell HMR4007 - page 7

    HMR4007 SENSOR PRODUCTS USING THE HMR4007 IN DIGITAL COMMUNICATI ONS MODE Introduction The HMR4007 is capa ble of communicating with a higher-level system throug h a proprietary communications po rt (J1). This port uses a bit-clocked seri al protocol for higher speed and hi gher data integrity than standard serial protocols. Signal levels are stand ...

  • Honeywell HMR4007 - page 8

    HMR4007 SENSOR PRODUCTS The second function, "CurrentPosition", is used to query the current position of the magnet. The following 16-bit integer values are returned: 0-1024 normal position response where 1024 represents full scal e response. -1, -2 communications failure. The sensor failed to respond to the PC quickly enough. This is usu ...

Manufacturer Honeywell Category Home Safety Product

Documents that we receive from a manufacturer of a Honeywell HMR4007 can be divided into several groups. They are, among others:
- Honeywell technical drawings
- HMR4007 manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell HMR4007
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell HMR4007.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell HMR4007, service manual, brief instructions and user manuals Honeywell HMR4007. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell HMR4007.

Similar manuals

A complete manual for the device Honeywell HMR4007, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell HMR4007 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell HMR4007.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell HMR4007 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell HMR4007, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell HMR4007, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell HMR4007 - which should help us in our first steps of using Honeywell HMR4007
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell HMR4007
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell HMR4007 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell HMR4007?

Use the form below

If you did not solve your problem by using a manual Honeywell HMR4007, ask a question using the form below. If a user had a similar problem with Honeywell HMR4007 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)