English dropdown-ico

Manual Craftsman 486.24839

28 pages 1.23 mb
Download

Go to site of 28

Summary
  • Craftsman 486.24839 - page 1

    Owner's Manual CRAFTSMAN 40"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT Model No. 486.24839 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • Assembly • Operation • Maintenance • Parts Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. pRINTED IN U.S.A. ...

  • Craftsman 486.24839 - page 2

    ACCESSORIES ........................................................... 2 SAFETY RULES .......................................................... 3 FULL SIZE HARDWARE CHART ................................. 4 CARTON CONTENTS ................................................. 5 ASSEMBLY ................................................................ ...

  • Craftsman 486.24839 - page 3

    Any power equipment can cause injury if operated improperly or if the user does not understand hew to operate the equipment. Exercise caution at all times, when using power equipment. • Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly. • Never allow chi ...

  • Craftsman 486.24839 - page 4

    SPARE PARTS BAG Store these two bolts and nuts In a safe place until needed. (See page 20.) SHOWN ACTUAL SIZE NOT SHOWN ACTUAL SIZE /CC / FF . EE /oo _ KK REF. A B C D E F G H I J K L M N O P Q R QTY. 1 4 2 6 2 4 2 2 6 2 4 10 14 1 2 7 2 2 DESCRIPTION Hex Bolt, 1/2" x 1-1/4" Hex Bolt, 3/8" x 1" , Hex Bolt, 5/16" x 1-3/4" ...

  • Craftsman 486.24839 - page 5

    CARTON CONTENTS 1. Cross Brace (Weight Tray) 2. Side Brace (Weight Tray) 3. Right Hand Side Plate (Stamped "R") 4. Left Hand Side Plate (Stamped "L") 5. Anti-rotation Bracket 6. Engagement Rod (Not used on some models) 7. Engine Pulley Keeper 8. Chute Crank Rod Assembly 9. Support Tube, Crank Rod 10. Lift Handle Tube and Cable 1 ...

  • Craftsman 486.24839 - page 6

    TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 1/2' Wrenches (2) 9/16" Wrenches (2) 3/4" Wrenches (1) Knife ADDITIONAL ITEMS REQUIRED General Purpose Grease ASSEMBLY OF SIDE PLATES TO TRACTOR Right hand (R,H.) and left hand (L.H.) side of the tractor are determined from the operators position while seated on the tractor. TRA ...

  • Craftsman 486.24839 - page 7

    Assemble a shoulder bolt, a 3/8" lock washer and a 3/8" hex lock nut to the bottom hole in each side plate. See figure 3. Proceed to page 8. 3_" HEX LOCK NUT _8"LOCK WASHER R. H. SIDE PLATE FIGURE 3 3/8" SHOULDER BOLT RIGHT SIDE VIEW Attach the R.H. Side Plate (marked "R") to the right side of the tractor frame as ...

  • Craftsman 486.24839 - page 8

    INSTALLING HANGER BRACKETS For better clearance, lower the tractor's suspension arms using the attachment lift lever. On Tractors With Foot Rest Brackets (Figure 7) • Remove the bolt and nut that fasten the L.H. and R.H. foot rest brackets to the frame. See figure 7. • Attach the L,H. Hanger Bracket (marked "L') to the inside of ...

  • Craftsman 486.24839 - page 9

    INSTALLING CLUTCH/IDLER ASSEMBLY This section covers the installation of the Clutch/Idler assembly to tractors with attachment clutches that are either rod operated (p, 9), cable operated (p. 10) or electric (p. 12). Use the appropriate instructions for your tractor. ROD OPERATED ATTACHMENT CLUTCHES • Move the attachment clutch lever on the dash ...

  • Craftsman 486.24839 - page 10

    Assemble the short "V" belt onto the engine pulley and then onto the large pulley on top of the clutch/ idler assembly. The belt must be placed to the inside of the engine pulley keeper, the idler pulley and the keeper bolt located beside the large pulley. See figure 14. IMPORTANT: Do Not assemble the "V" belt around the outside ...

  • Craftsman 486.24839 - page 11

    Attach the clutch/idler assembly to the tractor frame by sliding the notched arms at the rear of the assembly onto the two shoulder bolts assembled to the inside of the tractor frame. Lift the front of the assembly, fitting the sides into the R.H. and L.H. hanger brackets. Attach the assembly to the brackets using two pivot lock pins and 1/8" ...

  • Craftsman 486.24839 - page 12

    ELECTRIC A'n'ACHMENT CLUTCHES • Turn the clutch/idler assembly upside down and place the extra tensioning chain through the left front hole as shown in figure 19. / TENSIONING CHAIN FIGURE 19 Hook the loose spring through the end of the tensioning chain. See figure 20. Hook the other end of the spring onto the bottom of the bolt and nut ...

  • Craftsman 486.24839 - page 13

    Hold this drawing above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in the drawing will be the reverse of the viewer's right and left. ENGINE Left Side PULLEY of Tractor KEEPER 1/8" HAIRPIN COTTER / IDLER L. KEEPER BOLT ASSEMBLY OF THE SNOW THROWER Place the lift handle into the lift bracket on ...

  • Craftsman 486.24839 - page 14

    • Tilt the snow thrower back down to the ground. • Remove the nylon tie which fastens the auger drive belt to the discharge housing, leaving the belt assembled around the pulleys. • Remove the nylon tie which fastens the chute crank rod to the crank rod support tube. • Assemble the crank rod support tube to the bracket on the left side of t ...

  • Craftsman 486.24839 - page 15

    A'I-rACHING SNOW THROWER TO TRACTOR NOTE: An additional person's help may be required to mount the snow thrower to the front of the tractor. • Place the tractor and snow thrower on a flat, level surface so that the tractor can be rolled forward to attach the snow blower. • Remove the Attachment Pin from the snow thrower. Extend the be ...

  • Craftsman 486.24839 - page 16

    INSTALLING THE ATTACHMENT PIN Lift the front of the snow blower to align the holes in the mounting plates and the side plates. From the left side of the tractor install the attachment pin through the holes, securing it with the 1/8" hairpin cotter. Refer back to figure 29 on page 15. SETrlNG THE AUGER BELT TENSION Pull the tensioning chain unt ...

  • Craftsman 486.24839 - page 17

    • Place the plastic keg on the weight tray and fill with approximately 75 Ibs. of dry sand. • Secure the keg with the rubber tarp strap hooked into the holes in the cross brace. See figure 34. ! TARP STRAP FIGURE 34 USE THESE INSTRUCTIONS IF HEX BOLT INTERFERES WITH TIRE CHAINS • Block up the rear of the tractor to allow removal of rear wheel ...

  • Craftsman 486.24839 - page 18

    KNOW YOUR SNOW THROWER Read this owner's manual and safety rules before operating your snow thrower, Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations. CHUTE TILTHANDLE CRANK ROD CHUTE TILT HANDLE Pivots the Upper Chute up or down to control the angle and distance of dis ...

  • Craftsman 486.24839 - page 19

    RAISING AND LOWERING • To raise, push down on the lift handle until the snow thrower locks in the raised transport position. • To lower, push down slightly on the lift handle and pull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the ground. & CAUTION: Do not operate the snow thrower without the rear w ...

  • Craftsman 486.24839 - page 20

    & CAUTION: Before servicing or adjusting the snow thrower, shut off the engine, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition. REPLACING AUGER BELT • Disengage the tractor's attachment clutch. • Lower the snow thrower to the ground. • Remove the attachment pin. • Lock the snow thr ...

  • Craftsman 486.24839 - page 21

    STORAGE RECOMMENDATIONS • Lower the snow thrower to the ground. • Remove the snow thrower from the tractor. • Clean the snow thrower thoroughly. Wash off any salt deposit which may have dried on the thrower and housing. • Any bare metal that has become exposed should be painted or coated with a light oil to prevent rust. • Store in a dry ...

  • Craftsman 486.24839 - page 22

    REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER 74 17 16 33 ! 8 30 23_- 78 77 28 21 94 19 34 12 21 / 34 31 91 37 98 92 27 21 27 29 21 47 65 9 43 82 65 49 100 25 7 o 49 _ 99 22 95 / 64_ 60 63 45 49 68 .87 84 ...

  • Craftsman 486.24839 - page 23

    REF. NO. 1 2 3 4 5 6 7 8 9 !0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4O 41 42 43 44 45 46 47 48 49 50 51 52 53 54 REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER PART NO. 05931 63562 618-0161A 63579 63768 24278 703-2734 703-2735A 703-2736 705-5226 705-5269 705-5270 43182 44950 44917 44326 43080 ...

  • Craftsman 486.24839 - page 24

    REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER 42 43 4O 47 51 50 I 18 63 53 18 52 74 39 52 26 1_ t f 15 / 69 56 6O 58 6O 1 61 / 81 62 14 57 61 60 18 65 54 6 16 /_ 28 5 31 62 61 / 1 5 73 61 60 38 _3 55 12 18 22 ao 36 35 75 76 63 6 8 78 _9 23 24 A 24 ...

  • Craftsman 486.24839 - page 25

    REF. 2 3 4 5 6 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 135 _36 i 37 38 39 40 REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER PART NO. QTY. DESCRtPTION REF NO. 63764 1 710-0865 2 710-0367 2 711-0332 2 712-0261 2 43262 6 142 4 43093 1 IR19171616 6 741-0192 2 783-0380 2 783-0381 2 24476 2 24311 1 47599 2 4308 ...

  • Craftsman 486.24839 - page 26

    NOTES '26 I ...

  • Craftsman 486.24839 - page 27

    I 10 ° & CAUTION: DO NOT OPERATE YOUR TRACTOR AND SNOW THROWER ON A SLOPE IN EXCESS OF 10 DEGREES. BE SURE OF YOUR TRACTOR'S TOWING AND BRAKING CAPABILITIES BEFORE OPERATING ON A SLOPE. AVOID ANY SUDDEN TURNS OR MA- NEUVERS WHILE ON A SLOPE. 0 ...

  • Craftsman 486.24839 - page 28

    For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME" 0-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 In Canada for all your service and parts needs call - 1-600-665-4455 Au Canada pour tout le service ou les pi_ces For the repair or replacement parts you need: Call 7 am - 7 ...

Manufacturer Craftsman Category Lawn Mower Accessory

Documents that we receive from a manufacturer of a Craftsman 486.24839 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 486.24839 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 486.24839
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 486.24839.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 486.24839, service manual, brief instructions and user manuals Craftsman 486.24839. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 486.24839.

Similar manuals

A complete manual for the device Craftsman 486.24839, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 486.24839 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 486.24839.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 486.24839 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 486.24839, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 486.24839, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 486.24839 - which should help us in our first steps of using Craftsman 486.24839
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 486.24839
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 486.24839 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 486.24839?

Use the form below

If you did not solve your problem by using a manual Craftsman 486.24839, ask a question using the form below. If a user had a similar problem with Craftsman 486.24839 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)