English dropdown-ico

Manual Bryant HUM-56-1

12 pages 0.17 mb
Download

Go to site of 12

Summary
  • Bryant HUM-56-1 - page 1

    NOTE: Read the entire instruction in manual applicable to specific unit before starting the installation. This symbol → indicates a change since the last issue. SAFETY CONSIDERATIONS Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause personal ...

  • Bryant HUM-56-1 - page 2

    I. INSPECT PACKAGE AND CHECK EQUIPMENT Inspect contents of packaged humidifier. File claim with shipping company prior to installation if shipment is damaged or incom- plete. The package should contain: 1. Humidifier and media assembly 2. Humidistat 3. Template 4. Owner’s Manual 5. Warranty Certificate 6. Solenoid valve with bridge rectifier 7. S ...

  • Bryant HUM-56-1 - page 3

    VI. INSTALL DRAIN LINE 1. Use 1/2- or 5/8-in. vinyl tubing (field supplied) to connect drain on bottom of humidifier housing to an open drain. 2. Use supplied worm clamp to hold drain tubing in position over drain fitting outlet. CAUTION: Unit may leak if drain tubing is misapplied. Do not insert tubing inside of drain fitting outlet. 3. Make sure ...

  • Bryant HUM-56-1 - page 4

    II. SELECT LOCATION (SEE FIG. 5.) Humidifier must be installed on supply plenum only. If furnace has air conditioning coil, be sure humidifier does not interfere with coil ends. Remember to provide clearance for maintenance and evaporator pad removal. To access pad remove top or bottom cover to expose assembly (turn knob counter-clockwise). III. PR ...

  • Bryant HUM-56-1 - page 5

    INSTALLATION OF HUMBBSFP1016-A-- FAN POWERED HUMIDIFIER Bryant’s HUMBBSFP1016-A-- fan powered humidifier can only be installed on the supply plenum of a forced-air system. This unit requires an external 115-vac (fused) plug-in receptacle near the equipment for proper operation. It is recommended to install the humidifier where it can be easily se ...

  • Bryant HUM-56-1 - page 6

    IV. MOUNT THE HUMIDIFIER 1. Attach foam tape to back of mounting flange (exclude the off-set edge). 2. Hook off-set edge over opening cut in plenum. 3. Place humidifier in plenum aligning screw holes with flange. 4. Align, level, and tighten all screws for air tight seal. V. INSTALL DRAIN LINE 1. Use 5/8-in. vinyl tubing (field supplied) to connect ...

  • Bryant HUM-56-1 - page 7

    INSTALLATION OF HUMBBSBP2017-A-- BYPASS HUMIDIFIER Bryant’s HUMBBSBP2017-A-- bypass humidifier can be installed on either the supply or return plenum of a forced air system. This unit requires an external bypass duct between the supply- and return-air ductwork. It is recommended to install the humidifier where it can be easily serviced. If this h ...

  • Bryant HUM-56-1 - page 8

    5. Attach transfer tube to solenoid valve and insert free end into inlet fitting on top of unit housing. 6. Attach bridge rectifier to solenoid valve. 7. Insert sheet metal screws into lower holes in plenum, pre-drilled using template. 8. Tighten screws until heads protrude approximately 3/16-in. 9. Hang humidifier on bottom screws and push top of ...

  • Bryant HUM-56-1 - page 9

    II. SELECT LOCATION (SEE FIG. 14.) Humidifier may be installed on either supply or return plenum. If furnace has air conditioning coil, be sure humidifier does not interfere with coil ends. Remember to provide clearance for maintenance and evaporator pad removal. III. PREPARE PLENUM OPENING (SEE FIG. 2.) 1. Use template for marking humidifier openi ...

  • Bryant HUM-56-1 - page 10

    VIII. INSTALL HUMIDISTAT AND COMPLETE WIRING 1. Mount humidistat on inside wall or return-air duct in accordance with section INSTALLATION OF HUMIDIS- TAT on page 10. NOTE: Wiring must comply with national electrical code and any local codes or ordinances that may apply. (See Fig. 17.) IX. START-UP 1. Open saddle valve to permit water to flow to th ...

  • Bryant HUM-56-1 - page 11

    II. DUCT MOUNTING (LOW VOLTAGE) 1. Locate humidistat at least 8 in. upstream of humidifier in return-air duct. If mounting near elbow area, keep device 6 in. upstream of elbow so element will be affected by normal airflow. (See Fig. 20.) 2. Remove protective backing from template furnished with each control and apply self-adhesive side on return ai ...

  • Bryant HUM-56-1 - page 12

    V. OPERATION When relative humidity falls to humidistat set point, the humidistat switch makes contact and starts humidifier. In some central unit humidifier systems, furnace fan must be operating before humidi- fier will start. An increase in relative humidity above set point will stop humidifier. VI. CHECKOUT Place system in operation and observe ...

Manufacturer Bryant Category Humidifier

Documents that we receive from a manufacturer of a Bryant HUM-56-1 can be divided into several groups. They are, among others:
- Bryant technical drawings
- HUM-56-1 manuals
- Bryant product data sheets
- information booklets
- or energy labels Bryant HUM-56-1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bryant HUM-56-1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bryant HUM-56-1, service manual, brief instructions and user manuals Bryant HUM-56-1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bryant HUM-56-1.

Similar manuals

A complete manual for the device Bryant HUM-56-1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bryant HUM-56-1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bryant HUM-56-1.

A complete Bryant manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bryant HUM-56-1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bryant HUM-56-1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bryant HUM-56-1, that we can find in the current document
3. Tips how to use the basic functions of the device Bryant HUM-56-1 - which should help us in our first steps of using Bryant HUM-56-1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bryant HUM-56-1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bryant HUM-56-1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bryant HUM-56-1?

Use the form below

If you did not solve your problem by using a manual Bryant HUM-56-1, ask a question using the form below. If a user had a similar problem with Bryant HUM-56-1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)