English dropdown-ico

Manual Briggs & Stratton 500Z - 26

16 pages 0.97 mb
Download

Go to site of 16

Summary
  • Briggs & Stratton 500Z - 26 - page 1

    1/2008 1 5101454 Rev. IR TP 300-7368-IR-ZT-N Dealer Setup & Adjustment Instructions 500Z - 26 HP Briggs & Stratton 48” Mower Deck T ABLE OF CONTENTS: SETUP PROCEDURES Quick Setup List ................................................................2 Uncrating ............................................................................3 Ba ...

  • Briggs & Stratton 500Z - 26 - page 2

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 2 Quick Setup List - P age Setup Procedure Steps to P erform 3 Uncrating ❏ Remov e Crate & Banding. ❏ Disengage T ransmission Release Le v ers. ❏ Release P arking Brake and Roll T r actor forw ard off skid. ❏ Engage T ransmission Release Le v ers. 3 Battery Installation ❏ Instal ...

  • Briggs & Stratton 500Z - 26 - page 3

    500Z 26HP - 48” Mower Dec k 1/2008 3 TP 300-7368-IR-ZT-N Uncrating 1. Using a reciprocating utility saw or equivalent, cut the crate away from the bottom skid. Remove the crate. Remove the shrink-wrap plastic. 2. Cut the nylon banding from the front of the frame and the rear of the bumper. 3. Pull both transmission release levers (A, Figure 1) ba ...

  • Briggs & Stratton 500Z - 26 - page 4

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 4 T ractor Assembl y Install Gr ound Speed Control Le vers 1. Install the ground speed control levers (A, Figure 3) onto the control lever base (B) using the 5/16-18 x 3/4” bolts, 5/16” lock washers and 5/16” flat washers (C, D & E). Prior to tightening the bolts, align the handles ...

  • Briggs & Stratton 500Z - 26 - page 5

    500Z 26HP - 48” Mower Dec k 1/2008 5 TP 300-7368-IR-ZT-N Chec k Fluid Le vels Chec k the Engine Oil Level 1. Use the engine oil dipstick (A, Figure 5) to check the engine oil level. If necessary add engine oil. Check the engine manufacturer’s owner’s manual for the oil recommendations. Chec k / Fill T ransmission Oil Oil Type: 20W-50 conventi ...

  • Briggs & Stratton 500Z - 26 - page 6

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 6 Chec k the Mower Assembl y Chec k T or que - Mower Blades 1. Park the machine on a flat, level surface and engage the parking brake. 2. Lock the deck lift pedal in the 4-1/2” (11,47 cm) position. 3. Check that blades are installed with the tabs pointing up toward the deck as shown in Figu ...

  • Briggs & Stratton 500Z - 26 - page 7

    500Z 26HP - 48” Mower Dec k 1/2008 7 TP 300-7368-IR-ZT-N Chec k Deck Rod Timing 1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 40 psi (2,76 bar). 2. To check the lift rod timing, measure and record the distance between the ...

  • Briggs & Stratton 500Z - 26 - page 8

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 8 Figure 10. 2 x 4 Locations Figure 11. Hanger Chain Adjustment Dec k Leveling Adjustment NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted. 1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. ...

  • Briggs & Stratton 500Z - 26 - page 9

    500Z 26HP - 48” Mower Dec k 1/2008 9 TP 300-7368-IR-ZT-N Chec k Deck Drive Belt 1. Lower the mower deck to its lowest cutting position. 2. Remove the mower deck guards. 3. Make sure the V-side of the belt runs in the pulley grooves (Figures 14). 4. If the belt is not properly seated, use a 1/2” breaker bar, and place the square end in the squar ...

  • Briggs & Stratton 500Z - 26 - page 10

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 10 Lubrication Lubricate the unit at the locations shown in Figure 15 through18 as well as the following lubrication points. Grease: • front caster wheel axles and yokes • deck lift pivot blocks • mower deck spindles • mower deck idler arm Use grease fittings when present. Disassemble ...

  • Briggs & Stratton 500Z - 26 - page 11

    500Z 26HP - 48” Mower Dec k 1/2008 11 TP 300-7368-IR-ZT-N Figure 19. Adding Fuel A. Fuel Cap A Adding Fuel To add fuel: 1. Remove the fuel cap (A, Figure 19). 2. Fill the tank to about 1-1/2” (3,81 cm) of the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recom ...

  • Briggs & Stratton 500Z - 26 - page 12

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 12 P erf orm the Safety Chec ks Functional T ests 1. Check the tractor for loose bolts, screws, nuts, etc. 2. Start the engine and check all the controls for proper operation: ground speed control levers, parking brake, throttle cable, electric PTO clutch, etc. 3. Stop the engine and check fo ...

  • Briggs & Stratton 500Z - 26 - page 13

    500Z 26HP - 48” Mower Dec k 1/2008 13 TP 300-7368-IR-ZT-N Adjustment Pr ocedures Seat Adjustment See Figure 20. The seat can be adjusted forward and backward. Move the seat adjustment lever towards the left, position the seat as desired, and release the seat adjustment lever to lock the seat into position. A Figure 20. Seat Adjustment A. Seat Adj ...

  • Briggs & Stratton 500Z - 26 - page 14

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 14 Return-T o-Neutral Adjustment To determine if it is necessary to adjust the neutral return, perform the following steps. 1. Disengage the PTO, engage the parking brake and turn off the engine. 2. Move the ground speed control levers into the operating position, pull levers rearward and rel ...

  • Briggs & Stratton 500Z - 26 - page 15

    500Z 26HP - 48” Mower Dec k 1/2008 15 TP 300-7368-IR-ZT-N P arking Brake Adjustment 1. Disengage the PTO, stop the engine, engage the parking brake, and remove the key from the ignition. 2. Raise the seat plate to gain access to the parking brake components. 3. Measure the distance from the top of the brake spring rod (C, Figure 23) to the top of ...

  • Briggs & Stratton 500Z - 26 - page 16

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 16 PRODUCTS, INC. 535 Macon Street McDonough, GA., 30253 www.snapper.com The Snapper logo is a trademark of Briggs & Stratton Corporation, Milwaukee, WI, USA Briggs & Stratton Yard Power Products Group Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights ...

Manufacturer Briggs & Stratton Category Lawn Mower Accessory

Documents that we receive from a manufacturer of a Briggs & Stratton 500Z - 26 can be divided into several groups. They are, among others:
- Briggs & Stratton technical drawings
- 500Z - 26 manuals
- Briggs & Stratton product data sheets
- information booklets
- or energy labels Briggs & Stratton 500Z - 26
All of them are important, but the most important information from the point of view of use of the device are in the user manual Briggs & Stratton 500Z - 26.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Briggs & Stratton 500Z - 26, service manual, brief instructions and user manuals Briggs & Stratton 500Z - 26. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Briggs & Stratton 500Z - 26.

Similar manuals

A complete manual for the device Briggs & Stratton 500Z - 26, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Briggs & Stratton 500Z - 26 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Briggs & Stratton 500Z - 26.

A complete Briggs & Stratton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Briggs & Stratton 500Z - 26 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Briggs & Stratton 500Z - 26, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Briggs & Stratton 500Z - 26, that we can find in the current document
3. Tips how to use the basic functions of the device Briggs & Stratton 500Z - 26 - which should help us in our first steps of using Briggs & Stratton 500Z - 26
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Briggs & Stratton 500Z - 26
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Briggs & Stratton 500Z - 26 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Briggs & Stratton 500Z - 26?

Use the form below

If you did not solve your problem by using a manual Briggs & Stratton 500Z - 26, ask a question using the form below. If a user had a similar problem with Briggs & Stratton 500Z - 26 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)