English dropdown-ico

Manual John Deere ET-3302-J

20 pages 0.12 mb
Download

Go to site of 20

Summary
  • John Deere ET-3302-J - page 1

    7-Inch Disc Grinder Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE DISC GRINDER AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT. ET -3302-J 7-INCH GRINDER ...

  • John Deere ET-3302-J - page 2

    2 7-Inch Disc Grinder Operator's Manual Congratulations on the purchase of your new disc grinder! You can be assured your grinder was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This operator's manual was compiled for your benefit. By r ...

  • John Deere ET-3302-J - page 3

    7-Inch Disc Grinder Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-10 GENERAL SAFETY RULES .................................................................. 4-10 FUNCTIONAL DESCRIPTION ............................................ ...

  • John Deere ET-3302-J - page 4

    4 7-Inch Disc Grinder Operator's Manual RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your tool or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A "DANGER, WARNING or CAUTION" safety warnin ...

  • John Deere ET-3302-J - page 5

    7-Inch Disc Grinder Operator's Manual 5 NEVER TOUCH MOVING PARTS Never place your hands, fingers or other body parts near the tool’s moving parts. NEVER OPERATE WITHOUT ALL GUARDS IN PLACE Never operate this tool without all guards or safety features in place and in proper working order. If maintenance or servicing requires the removal of a ...

  • John Deere ET-3302-J - page 6

    6 7-Inch Disc Grinder Operator's Manual DRESS PROPERLY Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair. USE FACE, DUST MASK OR RESPIRATOR IF OPERATION IS DUSTY All persons in the area where po ...

  • John Deere ET-3302-J - page 7

    7-Inch Disc Grinder Operator's Manual 7 CAUTION STORE TOOL PROPERLY When not in use, the tool should be stored in a dry place. Keep out of reach of children. Lock-out the storage area. KEEP WORK AREA CLEAN Cluttered areas and benches invite injuries. Clear all work areas and work benches of unnecessary tools, debris, furniture, etc. DON’T FO ...

  • John Deere ET-3302-J - page 8

    8 7-Inch Disc Grinder Operator's Manual HANDLE TOOL CORRECTLY Operate the tool according to the instructions provided herein. Do not drop or throw the tool. Never allow the tool to be operated by children, individuals unfamiliar with its operation or unauthorized personnel. KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN PLACE Keep all screws, bo ...

  • John Deere ET-3302-J - page 9

    7-Inch Disc Grinder Operator's Manual 9 USE OF EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct siz ...

  • John Deere ET-3302-J - page 10

    10 7-Inch Disc Grinder Operator's Manual IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE DISC GRINDER WARNING: DEATH OR SERIOUS BODILY INJURY COULD RESULT FROM IMPROPER OR UNSAFE USE OF THE DISC GRINDER. 1. NEVER operate the disc grinder without its wheel guard in place. 2. NEVER place hands or body parts near the disc during operation. 3. NEVER ...

  • John Deere ET-3302-J - page 11

    7-Inch Disc Grinder Operator's Manual 11 Functional Description MODEL : ET-3302-J 7-INCH DISC GRINDER NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all s ...

  • John Deere ET-3302-J - page 12

    12 7-Inch Disc Grinder Operator's Manual WARNING: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG FROM THE RECEPTACLE TO AVOID SERIOUS TROUBLE. 1. Assembling: a. Turn the disc grinder upsidedown so that the spindle is facing upward. b. To mount the wheel guard on the grinder first, slip the set ring (A) over the guard mounting flange, so l ...

  • John Deere ET-3302-J - page 13

    7-Inch Disc Grinder Operator's Manual 13 1. Power source: Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. 2. Power switch: Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will ...

  • John Deere ET-3302-J - page 14

    14 7-Inch Disc Grinder Operator's Manual OPERATION: 1. Always hold the handle and side handle of the POWER TOOL firmly. Otherwise the counterforce produced may result in inaccurate and even dangerous operation. 2. Grinding Pressure: Since grinding by utiliing only the Disc Grinder's won weight is feasible, hold the Disc Grinder so that it ...

  • John Deere ET-3302-J - page 15

    7-Inch Disc Grinder Operator's Manual 15 OPERATION (CONTINUED): 3. Grinding angle: Use only its peripheral surface by tilting the grinding wheel at an angle of 15° - 30°, as shown in Fig. 3-a. CAUTION: DO NOT UTILIZE THE ENTIRE SURFACE OF GRINDING WHEEL WHEN GRINDING. 4. When using a new grinding wheel in direction A (Fig. 3-a), the wheel ed ...

  • John Deere ET-3302-J - page 16

    16 7-Inch Disc Grinder Operator's Manual Maintenance and Inspection WARNING: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG FROM THE RECEPTACLE DURING MAINTENANCE AND INSPECTION. 1. Replacing the grinding wheel: Replace the grinding wheel when it has been worn out to about 2-3/8" (60mm) in external diameter. Confirm that there is no ...

  • John Deere ET-3302-J - page 17

    7-Inch Disc Grinder Operator's Manual 17 Maintenance and Inspection WARNING: ACCESSORIES FOR THIS POWER TOOL ARE MENTIONED IN THIS INSTRUCTION MANUAL. THE USE OF ANY OTHER ATTACHMENT OR ACCESSORY CAN BE DANGEROUS AND COULD CAUSE INJURY OR MECHANICAL DAMAGE. STANDARD ACCESSORIES: -Wrench 1 -Side Handle 1 -Hexagon Bar Wrench 1 NOTE: Accessories ...

  • John Deere ET-3302-J - page 18

    18 7-Inch Disc Grinder Operator's Manual Notes ...

  • John Deere ET-3302-J - page 19

    7-Inch Disc Grinder Operator's Manual 19 Notes ...

  • John Deere ET-3302-J - page 20

    20 7-Inch Disc Grinder Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 7-Inch Disc Grinder Operator's Manual 110 Code No. C99110961 N #37-0696-090403 © Copyright 2003. John Deere ...

Manufacturer John Deere Category Grinder

Documents that we receive from a manufacturer of a John Deere ET-3302-J can be divided into several groups. They are, among others:
- John Deere technical drawings
- ET-3302-J manuals
- John Deere product data sheets
- information booklets
- or energy labels John Deere ET-3302-J
All of them are important, but the most important information from the point of view of use of the device are in the user manual John Deere ET-3302-J.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals John Deere ET-3302-J, service manual, brief instructions and user manuals John Deere ET-3302-J. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product John Deere ET-3302-J.

Similar manuals

A complete manual for the device John Deere ET-3302-J, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use John Deere ET-3302-J by users. Manuals are usually written by a technical writer, but in a language understandable to all users of John Deere ET-3302-J.

A complete John Deere manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual John Deere ET-3302-J - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the John Deere ET-3302-J, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the John Deere ET-3302-J, that we can find in the current document
3. Tips how to use the basic functions of the device John Deere ET-3302-J - which should help us in our first steps of using John Deere ET-3302-J
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with John Deere ET-3302-J
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of John Deere ET-3302-J in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning John Deere ET-3302-J?

Use the form below

If you did not solve your problem by using a manual John Deere ET-3302-J, ask a question using the form below. If a user had a similar problem with John Deere ET-3302-J it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)