Manual Skil 2367

40 pages 0.61 mb
Download

Go to site of 40

Summary
  • Skil 2367 - page 1

    IMPORT ANT : IMPORT ANT : IMPORT ANTE: Read Before Using Lire avant usage Leer antes de usar Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad 2367 2467 2567 2867 For English Version Version française Versión en español See page 2 Voir page 15 Ver la página 27 1-877-SKIL999 (1-877-7 ...

  • Skil 2367 - page 2

    Read and understand all instructions . Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS -2 - Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in t ...

  • Skil 2367 - page 3

    -3- Safety Rules for Cordless Drills/Drivers Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If da ...

  • Skil 2367 - page 4

    Battery/Charger before switching the tool "ON". Keys or wrenches can fly away at high velocity striking you or a bystander. Do not run the drill while carrying it at your side. A spinning drill bit could become entangled with clothing and injury may result. This tool may be used with sanding and polishing disks, grinding wheels, wire whee ...

  • Skil 2367 - page 5

    -5- When batteries are not in tool or charger, keep them away from metal objects. For example, to protect terminals from shorting DO NOT place batteries in a tool box or pocket with nails, screws, keys, etc. Fire or injury may result. To prevent fire or injury when batteries are not in tool or charger, always place protective cap onto end of batter ...

  • Skil 2367 - page 6

    -6- IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation V Volts Voltage (potential) A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power kg Kilogra ...

  • Skil 2367 - page 7

    Tool Model number 2367 2467 2567 2867 Voltage rating 9.6 V 12 V 14.4 V 18 V Charge time 3 hr. 3 hr. 3 hr. 3 hr. Chuck size 3/8" 3/8" 3/8" 3/8" Battery pack 96BAT 120BAT 144BAT 180BAT Charger 92370 92490 92590 92990 Voltage rating (all models) 120 V 60 Hz -7- Functional Description and Specifications Disconnect battery pack from ...

  • Skil 2367 - page 8

    -8- Operating Instructions VARIABLE SPEED CONTROLLED TRIGGER SWITCH Y our tool is equipped with a variable speed trigger switch. The tool speed can be controlled from the minimum to the maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed. This accurate spee ...

  • Skil 2367 - page 9

    * STUD FINDER Your tool may be equipped with a stud finder located on top of your tool. To remove, simply slide off the housing towards the back of the tool. Before first use, open the battery compartment door and remove the protective plastic insert from between the batteries. Assure proper battery placement as shown in the compartment and replace ...

  • Skil 2367 - page 10

    1. The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity. 2. The charger was designed to fast charge the battery only when the battery temperature is between 40˚F (4˚C) and 105˚F (41˚C). 3 . A substantial drop in oper ...

  • Skil 2367 - page 11

    -11- Operating Tips You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During the operation, hold the tool firmly and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from cutting and cause exce ...

  • Skil 2367 - page 12

    WIRE BRUSHES Work with brushes requires high speeds. BRUSHING PRESSURE 1. Remember, the tips of a wire brush do the work. Operate the brush with the lightest pressure so only the tips of the wire come in contact with the work. 2. If heavier pressures are used, the wires will be overstressed, resulting in a wiping action; and if this is continued, t ...

  • Skil 2367 - page 13

    -13- * Screwdriver bit ** Carrying case (* = standard equipment) (** = optional accessories) Accessories If an extension cord is necessary, a cord with adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use ...

  • Skil 2367 - page 14

    -14- Notes: BM 1619X01517 03-06 3/30/06 3:20 PM Page 14 ...

  • Skil 2367 - page 15

    -15- Vous devez lire et comprendre toutes les instructions. Le non-respect, même partiel, des instructions ci-après entraîne un risque de choc életrique, d'incendie et/ou de blessures graves. CONSERVEZ CES INSTRUCTIONS AVERTISSEMENT ! Aire de travail Veillez à ce que l'aire de travail soit propre et bien éclairée. Le désordre et l ...

  • Skil 2367 - page 16

    -16- Soyez attentif à tout désalignement ou coincement d es pièces en mouvement, à tout bris ou à toute autre c ondition préjudiciable au bon fonctionnement de l 'outil. Si vous constatez qu'un outil est endommagé, faites-le réparer avant de vous en servir. De nombreux accidents sont causés par des outils en mauvais état. N&apos ...

  • Skil 2367 - page 17

    -17- en marche. Les clés de serrage ou de réglage peuvent être projetées à grande vitesse et frapper une personne présente ou vous-même. Ne faites pas fonctionner la perceuse en la portant à votre côté. Un foret en rotation pourrait s'emmêlever à vos vêtements, ce qui pourrait causer des blessures. Cet outil peut être utilisé av ...

  • Skil 2367 - page 18

    -18- Lorsque les piles ne sont pas dans l’outil ou le chargeur, gardez-les à l’écart d’objets métalliques. Ainsi, pour éviter un court-circuitage des bornes, NE PLACEZ PAS les piles dans la boîte à outils ou dans la poche avec des clous, des vis, des clés, etc. Ceci peut provoquer un incendie ou des blessures. Afin d’éviter tout ris ...

  • Skil 2367 - page 19

    -19- Symboles IMPORTANT : Certains des symboles suivants peuvent être utilisés sur votre outil. Veuillez les étudier et apprendre leur signification. Une interprétation appropriée de ces symboles vous permettra d'utiliser l'outil de façon plus efficace et plus sûre. Symbole Nom Désignation/Explication V Volts Tension (potentielle) ...

  • Skil 2367 - page 20

    -20- Description fonctionnelle et spécifications Débranchez le bloc-piles de l'outil ou placez l'interrupteur à la position de blocage ou d'arrêt avant d'effectuer tout assemblage ou réglage ou de changer les accessoires. Ces mesures de sécurité préventives réduisent le risque d'une mise en marche accidentelle de l ...

  • Skil 2367 - page 21

    GÂCHETTE DE COMMANDE À VITESSE VARIABLE Votre outil est équipé d’une gâchette à vitesse variable. La vitesse de l’outil peut être contrôlée du régime minimum au régime maximum spécifiés sur la plaque signalétique par la pression que vous exercez sur la gâchette. Exercez plus de pression pour augmenter la vitesse et relâchez la p ...

  • Skil 2367 - page 22

    -22- * LOCALISATEUR DE POTEAUX Il se peut que votre outil soit muni sur son dessus d’un localisateur de poteaux. Pour l’enlever, il suffit de le faire coulisser vers l’arrière de l’outil. Avant la première utilisation, ouvrez le couvercle du compartiment des piles et enlevez le morceau de plastique intercalé entre celles-ci. Assurez-vous ...

  • Skil 2367 - page 23

    -23- CHARGE DU BLOC-PILES (CHARGEUR DE 3 HEURE) Branchez le cordon du chargeur dans votre prise de courant standard. Avant d’introduire le bloc-piles, retirez le capuchon de protection et introduisez le bloc- piles dans le chargeur (Fig. 6). Le témoin lumineux vert du chargeur (Fig. 7) s’allumera. Le témoin lumineux vert demeurera allumé tan ...

  • Skil 2367 - page 24

    -24- Vous prolongerez la durée de vos forets et accomplirez un travail plus net si vous mettez toujours le foret en contact avec le matériau avant d’appuyer sur la gâchette. Durant le fonctionnement, tenez l’outil fermement et exercez une pression légère et constante. Une trop grande pression à basse vitesse bloquera l’outil. Une pressi ...

  • Skil 2367 - page 25

    PERÇAGE DES MÉTAUX Il existe deux règles pour percer les matériaux durs. En premier lieu, plus le matériau est dur, plus il vous faut exercer de pression sur l’outil. En deuxième lieu, plus le matériau est dur, plus vous devez percer lentement. Voici quelques conseils pour percer les métaux. Lubrifiez la pointe du foret à l’occasion à ...

  • Skil 2367 - page 26

    -26- Entretien Service IL N’EXISTE À L’INTÉRIEUR AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. L’entretien préventif exécuté par des personnes non autorisés peut entraîner un positionnement erroné des composants et des fils internes, ce qui peut présenter de graves dangers. Nous recommandons de confier toute int ...

  • Skil 2367 - page 27

    -27- Lea y entienda todas las instrucciones. El incumplimiento de todas las instrucciones indicadas a continuación puede dar lugar a sacudidas eléctricas, incendios y/o lesiones personales graves. CONSERVE ESTAS INSTRUCCIONES Area de trabajo Mantenga el área de trabajo limpia y bien iluminada. Las mesas desordenadas y las áreas oscuras invitan ...

  • Skil 2367 - page 28

    -28- Mantenga las herramientas con cuidado. Conserve las herramientas de corte afiladas y limpias. Las herramientas mantenidas adecuadamente, con bordes de corte afilados, tienen menos probabilidades de atascarse y son más fáciles de controlar. Compruebe la desalineación o el atasco de las piezas móviles, la ruptura de piezas y cualquier otra s ...

  • Skil 2367 - page 29

    Compruebe que las llaves de ajuste y de tuerca se hayan quitado del taladro antes de encender la herramienta . Las llaves de ajuste o de tuerca pueden salir despedidas a gran velocidad y golpearle a usted o golpear a alguien que se esté presente. No tenga en marcha el taladro mientras lo lleva a su lado. Una broca taladradora que gira podría enga ...

  • Skil 2367 - page 30

    -30- Cuando las baterías no están en la herramienta o en el cargador, manténgalas alejadas de objetos metálicos. Por ejemplo, para evitar que las terminales hagan corto- circuito, NO ponga las baterías en una caja de herramientas o en un bolsillo con clavos, tornillos, llaves, etc. Se pueden producir un incendio o lesiones. Para evitar incendi ...

  • Skil 2367 - page 31

    -31- Símbolos IMPORTANTE: Es posible que algunos de los símbolos siguientes se usen en su herramienta. Por favor, estúdielos y aprenda su significado. La interpretación adecuada de estos símbolos le permitirá utilizar la herramienta mejor y con más seguridad. Símbolo Nombre Designación/explicación V Volt Tensión (potencial) A Ampere Corr ...

  • Skil 2367 - page 32

    Descripción funcional y especificaciones Desconecte el paquete de baterías de la herramienta o ponga el interruptor en la posición fijada o de apagado antes de hacer cualquier ensamblaje, ajustes o cambiar accesorios. Dichas medidas preventivas de seguridad reducen el riesgo de arrancar la herramienta accidentalmente. ADVERTENCIA ! T aladros/des ...

  • Skil 2367 - page 33

    Instrucciones de funcionamiento INTERRUPTOR GATILLO DE VELOCIDAD VARIABLE CONTROLADA La herramienta está equipada con un interruptor gatillo de velocidad variable. La velocidad de la herramienta se puede controlar desde las “Revoluciones por minuto” mínimas hasta las “Revoluciones por minuto” máximas indicadas en la placa del fabricante ...

  • Skil 2367 - page 34

    -34- * LOCALIZADOR DE POSTES DE PARED La herramienta puede equiparse con un localizador de postes de pared ubicado en la parte de arriba de la herramienta. Para quitar el localizador, simplemente deslice la carcasa hacia la parte de atrás de la herramienta. Antes del primer uso, abra la puerta del compartimiento de las baterías y saque el accesor ...

  • Skil 2367 - page 35

    NOTAS IMPORTANTES PARA CARGAR 1. El paquete de baterías acepta únicamente alrededor del 80 por ciento de su capacidad máxima en los primeros ciclos de carga. Sin embargo, después de los primeros ciclos de carga, la batería se cargará hasta su capacidad máxima. 2. El cargador fue diseñado para cargar la batería rápidamente sólo cuando la ...

  • Skil 2367 - page 36

    SUJECION CON TORNILLOS El procedimiento mostrado en la (Fig. 8) le permitirá a usted sujetar unos materiales a otros usando el taladro/destornillador sin cordón sin desforrar, rajar ni separar el material. Primero, fije las piezas una a otra y taladre el primer agujero con 2/3 del diámetro del tornillo. Si el material es blando, taladre únicame ...

  • Skil 2367 - page 37

    ESCOBILLAS DE ALAMBRE El trabajo con escobillas requiere altas velocidades. PRESIÓN DE CEPILLADO 1. Recuerde que las puntas de un cepillo de alambre hacen el trabajo. Utilice el cepillo con la presión más ligera para que solamente las puntas del alambre entren en contacto con la pieza de trabajo. 2. Si se utilizan presiones más grandes, se some ...

  • Skil 2367 - page 38

    -38- Servicio NO HAY PIEZAS EN EL INTERIOR QUE PUEDAN SER AJUSTADAS O REPARADAS POR EL USUARIO. El mantenimiento preventivo realizado por personal no autorizado pude dar lugar a la colocación incorrecta de cables y componentes internos que podría constituir un peligro serio. Recomendamos que todo el servicio de las herramientas sea realizado en u ...

  • Skil 2367 - page 39

    -39- Remarques : Notas: BM 1619X01517 03-06 3/30/06 3:20 PM Page 39 ...

  • Skil 2367 - page 40

    1619X01517 03/06 Printed in China L IMITED WARRANTY OF SKIL CONSUMER PORTABLE POWER TOOLS FOR HOME USE Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all SKIL consumer portable power tools will be free from defects in material or workmanship for a period of two years from date of purchase. SELLER’S SOLE ...

Manufacturer Skil Category Drill

Documents that we receive from a manufacturer of a Skil 2367 can be divided into several groups. They are, among others:
- Skil technical drawings
- 2367 manuals
- Skil product data sheets
- information booklets
- or energy labels Skil 2367
All of them are important, but the most important information from the point of view of use of the device are in the user manual Skil 2367.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Skil 2367, service manual, brief instructions and user manuals Skil 2367. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Skil 2367.

Similar manuals

A complete manual for the device Skil 2367, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Skil 2367 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Skil 2367.

A complete Skil manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Skil 2367 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Skil 2367, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Skil 2367, that we can find in the current document
3. Tips how to use the basic functions of the device Skil 2367 - which should help us in our first steps of using Skil 2367
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Skil 2367
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Skil 2367 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Skil 2367?

Use the form below

If you did not solve your problem by using a manual Skil 2367, ask a question using the form below. If a user had a similar problem with Skil 2367 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)