English dropdown-ico

Manual Clarion MCD360

16 pages 0.28 mb
Download

Go to site of 16

Summary
  • Clarion MCD360 - page 1

    ...

  • Clarion MCD360 - page 2

    INTRODUCTION The Clarion MCD360 is a full-featured Three-Way Crossover. When used to build a 2-way system with front and rear fader capability or a full three-way system, the Clarion MCD360 electronic crossover allows you to choose from a wide range of crossover points between the front, rear and subwoofer outputs. The MCD360 includes the following ...

  • Clarion MCD360 - page 3

    INPUT/OUTPUT CONNECTIONS AND AUDIO CONTROLS The top panel of MCD360 contains the controls for the crossover and output levels as shown below. 3 1. Front RCA Input 2. Front Crossover Frequency Control 3. Front/Rear Input Selection Switch 4. Rear RCA Input 5. Rear Crossover Frequency Control 6. Sub Input Selection Switch 7. Sub RCAInput 8. Sub Crosso ...

  • Clarion MCD360 - page 4

    • Front High-Pass Crossover Frequency Adjustment - Adjusts the crossover to match your speaker system. The crossover frequency can be adjusted from 32Hz - 400Hz or from 640Hz - 8kHz with the crossover frequency multiplier switch. • Rear High-Pass Crossover Frequency Adjustment - Adjusts the crossover to match speaker your system. The crossover ...

  • Clarion MCD360 - page 5

    MOUNTING PRECAUTIONS The MCD360 crossover can be mounted in any convenient location in your vehicle that allows access to the controls and is away from moisture. The flanges on the chassis have mounting holes which can be used as a template for screw holes. For easy system set-up, mount the crossover so the front panel controls will be accessible a ...

  • Clarion MCD360 - page 6

    WIRING PRECAUTIONS Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer . If you are using a source unit, without a remote turn-on lead, the MCD360 can be turned on with a switched accessory lead. Y ou can find this accessory power source in the factory harness at the back of the radio. It is t ...

  • Clarion MCD360 - page 7

    7 Figure 3 - Electrical connections for the MCD-360 ...

  • Clarion MCD360 - page 8

    APPLICA TIONS The MCD360 allows you to design either a 2-way system with front and rear output or a full 3-way system. After determining which system best fits your requirements, thoroughly read and follow the directions below for your system type. 2-Way System with Front and Rear Output 8 Figure 4 - In this illustration, the MCD360 is configured f ...

  • Clarion MCD360 - page 9

    9 For 2 channel input, configure switches as shown. For 4 channel input with front and rear fade, configure switches as shown. For front and rear fade with dedicated subwoofer input, configure switches as shown. Figure 5- ...

  • Clarion MCD360 - page 10

    2-Way System Application Notes After all the wiring connections are made and before the system is turned on for the first time, you need to make some basic adjustments. It is important that the High-Pass and Low-Pass Frequency Controls are set correctly before turning on the system for the first time. Setting the Crossover Frequency Controls 1. Set ...

  • Clarion MCD360 - page 11

    Setting the Rear Output Level Before setting rear level controls, disconnect both the front output and the subwoofer output and follow the directions below . 1. T urn the output control level to the minimum setting. 2. T urn the amplifier gain controls to the minimum setting. 3. T urn the source unit on and increase the volume until distortion is h ...

  • Clarion MCD360 - page 12

    3-Way System 12 Figure 6 - In this illustration, the MCD360 is configured for single channel input with dedicated amplifiers for tweeters, midranges and subwoofer(s). ...

  • Clarion MCD360 - page 13

    3-Way System Application Notes After all the wiring connections are made and before the system is turned on for the first time, you need to make some basic adjustments. It is important that the High-Pass and Low-Pass Frequency Controls are set correctly before turning on the system for the first time. Setting the Crossover Frequency Controls 1. Set ...

  • Clarion MCD360 - page 14

    Setting the Sub Output Level 1. Make sure all ouputs are connected and both the front and rear output levels are set correctly. Unplug the Remote Sub Level control cable. 2. Be sure the sub output level and amplifier gains are at their minimum settings. 3. W ith the volume set at a medium level, slowly increase the sub level control to the point wh ...

  • Clarion MCD360 - page 15

    Problem: Midrange speakers “pop” with loud passages. Solution: High-Pass Frequency Control is set too low . Gain Controls on amplifiers are set incorrectly. Reduce the gain setting on high frequency amplifier . Problem: One channel does not operate. Solution: Swap left and right connections at the source unit. If the problem trades sides in the ...

  • Clarion MCD360 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com MCD360-10 Rev .1 (02/00) ...

Manufacturer Clarion Category Stereo Equalizer

Documents that we receive from a manufacturer of a Clarion MCD360 can be divided into several groups. They are, among others:
- Clarion technical drawings
- MCD360 manuals
- Clarion product data sheets
- information booklets
- or energy labels Clarion MCD360
All of them are important, but the most important information from the point of view of use of the device are in the user manual Clarion MCD360.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Clarion MCD360, service manual, brief instructions and user manuals Clarion MCD360. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Clarion MCD360.

Similar manuals

A complete manual for the device Clarion MCD360, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Clarion MCD360 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Clarion MCD360.

A complete Clarion manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Clarion MCD360 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Clarion MCD360, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Clarion MCD360, that we can find in the current document
3. Tips how to use the basic functions of the device Clarion MCD360 - which should help us in our first steps of using Clarion MCD360
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Clarion MCD360
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Clarion MCD360 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Clarion MCD360?

Use the form below

If you did not solve your problem by using a manual Clarion MCD360, ask a question using the form below. If a user had a similar problem with Clarion MCD360 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)