English dropdown-ico

Manual Craftsman 917.27206

64 pages 1.99 mb
Download

Go to site of 64

Summary
  • Craftsman 917.27206 - page 1

    Owner's Manual JCRAFTSMAN'J 16.0 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTOR Model No. 917.272060 • Safety • Assembly • Operation • Maintenance • Repair Parts This product has a low emiSsion engine which operates differently from previously built engines, Before you start the engine, read and understand this Owner&ap ...

  • Craftsman 917.27206 - page 2

    Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 8 Operation ............................................ 11 Maintenance ....................................... 18 Maintenance ...

  • Craftsman 917.27206 - page 3

    IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safely instructions could result in serious injury or death. I. GENERAL OPERATION II. SLOPE OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow respon ...

  • Craftsman 917.27206 - page 4

    III. CHILDREN Tragicaccidents can occur if the operator is not alert to the presence of children, Children are often attractedto the machine and the mowingactivity. Never assume that children will remain where you last saw them. • Keep childrenout of the mowing area and underthe watchful care of another responsible adult. • Be alert and tum mac ...

  • Craftsman 917.27206 - page 5

    • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Do not turn o ...

  • Craftsman 917.27206 - page 6

    PRODUCT SPECIFICATIONS SASOLINE 1.25 GALLONS CAPACITY UNLEADED _.ND TYPE: REGULAR DILTYPE SAE 10W30{above 32°F) _,PI-SF-SJ): SAE 5W-30 (below 32°F) ; OIL CAPACITY: W/FILTER: 4,0 PINTS W/OFILTER: 3.5 PINTS SPARK PLUG: CHAMPION RC12YC SAP: .040") VALVE CLEARANCE: NOT ADJUSTABLE GROUND FORWARD: 5.5 SPEED(MPH): REVERSE: 2.4 ]'IRE FRONT: 14 ...

  • Craftsman 917.27206 - page 7

    Steering Wheel Insert _1_(1) Hex Bolt 3/8-16 x 1 Steerin! _ Boot Steering Wheel (1) Lock washer 3/8 (1) Large Flat Washer (1) Hex Bolt 5/16-18 x 1-1/4 (1) Locknut 5/16-18 =_ Steedng Wheel Adapter t Stx_:nd;gn Shaft at (1)Washer 17/32 x 1-3/16 x 12 Gauge _(1) Knob Slope Sheet Keys € (2) Keys Video Cassette For Future Use ...

  • Craftsman 917.27206 - page 8

    Your new tractor has been assembled atthe factory with exception ofthose parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardwareyou assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Reviewthe video cassettebefore you begin. TOOLS REQUI ...

  • Craftsman 917.27206 - page 9

    Battery Door Terminal INSTALL SEAT Adjustseat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packingand set aside for assemblyof seat to tractor. 2. Pivotseat upward and remove from the cardboardpacking. Remove the cardboard packingand discard. 3. Place seat on seat pan so head of shoulderbol ...

  • Craftsman 917.27206 - page 10

    INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of muicher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck. 4. Hook rear latch into hole on back of mower deck. ,_CAUTION: Do not remove deflector shield fro ...

  • Craftsman 917.27206 - page 11

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING ENGINE ON ENGINE OFF REVERSE FORWARD FAST SLOW @ ixl FUEL CHOKE OIL PRESSURE LIGHTS ON OVER TEMP LIGHT MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT LOCKED _r_'m R N H L c®)_ I ATTACHMENT REVERSE ...

  • Craftsman 917.27206 - page 12

    KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of variouscontrols and adjustments. Save this manual for future reference. Attachment Clutch Ammeter Ignition Switch Light Switch Lift J Lever Plunger Throttle/Choke Atta ...

  • Craftsman 917.27206 - page 13

    The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repaim. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOWTO USEYOURTRACTOR TO SET PARKING ...

  • Craftsman 917.27206 - page 14

    • For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relativelyhigh;the second to desired height. TO ADJUST GAUGE WHEELS Gauge wheels are propedy adjusted when they are slightly off the ground when moweris at the desired cutting height in operatingposition. Gauge wheels then keep the deck in prob ...

  • Craftsman 917.27206 - page 15

    NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). TOWING CARTS AND OTHER ATTACH- MENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of you ...

  • Craftsman 917.27206 - page 16

    • The attachments and grounddrive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above. COLD WEATHER STARTING ( 50° F and below) 7. When engine starts, allow engine to run with the throttlecontrol in the choke position until the engine runs roughly, ...

  • Craftsman 917.27206 - page 17

    MOWINGTIPS • Mower should be properly leveled for best mowingperformance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the rightof the tracto ...

  • Craftsman 917.27206 - page 18

    MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES CheCk Brake O_Uorl Check Tire pro'_u_ V _ Check Operator Presence and T Intelt_k Systems II_ CheCk I0¢ LoOSe Fasteners ll_ I_z I_ A Sherper_Replsce Mower Bktde= I1_, T Check Battery Level R G lean Battery and Terminals I1_ V r Check Transaxle Cooling li_ Adjust B ...

  • Craftsman 917.27206 - page 19

    TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See &q ...

  • Craftsman 917.27206 - page 20

    BA'I-FERY Your tractor has a battery charging system which is sufficient fornormal use. How- ever, periodic charging ofthe battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equip ...

  • Craftsman 917.27206 - page 21

    8. Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at "FULL" line on dipstick. Tighten cap onto the tube securely when finished. Oil Drain Valve Closed and Locked Position Cap Drain Tube CLEAN AIR S ...

  • Craftsman 917.27206 - page 22

    3. Apply a thin coating of new engine oil to the rubber gasket on replacement oil filter. 4. Install replacement oil filter on filter adapter. Turn oil filter clockwise until rubber gasket contacts the filter adapter, then tighten filter an addi- tional 1/2 tum. 5. Fill crankcase with new oil (See "TO CHANGE ENGINE OIL" in this section of ...

  • Craftsman 917.27206 - page 23

    _CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position. 4. Turn ignition key "OFF" and remove key. 5. Make sure the blades and all moving parts have completely sto ...

  • Craftsman 917.27206 - page 24

    SIDE-TO-SIDE ADJUSTMENT • Raise mower to itshighest position. • At the midpoint of both sides of mower, measure height from bottom edge of mowerto ground. Distance "A"on both sides of mowershould be the same or within 1/4" of each other. • If adjustment is necessary, make adjustment on one side of moweronly. • To raise one si ...

  • Craftsman 917.27206 - page 25

    BELT INSTALLATION - 4. Install new belt in reverse order of removal. 5. Make sure belt is in all pulley grooves and inside all belt guides. 6. Install mower in reverse order of removal instructions. TO ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. If tractor requires more than s ...

  • Craftsman 917.27206 - page 26

    2. Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep. 3. Tighten adjustment bolt securely. 4. Start engine and test. 5. If tractor still creeps, repeat above steps until satisfied. Motion Control Neutral Lock Gate Lever TRANSMISSION REMOVAL/REPLACE- MENT Should your transmission require removal for service or repl ...

  • Craftsman 917.27206 - page 27

    REPLACING BATTERY _CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding, 1. Lift seat pan to raised position ...

  • Craftsman 917.27206 - page 28

    TO ADJUST CARBURETOR Thecarburetor has beenpreset at the factory and adjustment should notbe necessary, However, minor adjus_ant may be required to compensate fordifferences in fuel, temperature, altitude orload.If the cadouretor doesneed adjustment, proceed as follows: In general, turning the adjuslJng nsedles in (clockwise) decreases the supply o ...

  • Craftsman 917.27206 - page 29

    immediately prepare your tractor for storage at the end of the season or if the 'ractor will not be used for 30 days or ,'nore, CAUTION: Never store the tractor Nith gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tract ...

  • Craftsman 917.27206 - page 30

    TROUBLESHOOTING CHART PROBLEM Will not start Hard to start Engine will not turn over CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter, 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9. Carburetor out of adjustment. 10. Enginevalves out of adjustment. 1. D ...

  • Craftsman 917.27206 - page 31

    "ROUBLESHOOTING CHART CORRECTION PROBLEM Loss of power continued) Excessive vibration Englnecontinues to run when operator leaves seat with attachment clutch engaged Poorcut-uneven Mower blades will not rotate i CAUSE 3. Build-up of grass, leaves and trash under mower. 4. Dirty air filter. i 5. Low oil level/dirty oil. 6. Faulty spark plug. 7. ...

  • Craftsman 917.27206 - page 32

    TROUBLESHOOTING CHART PROBLEM CAUSE Poor grass 1. Engine speed too slow. discharge 2. Travel speed too fast. 3. Wet grass. 4. Mower deck not level. 5. Low/uneven tire air pressure, 6. Wom, bent or loose blade. 7. Buildup of grass, leaves and trash under mower. 8. Mower ddve belt worn. 9. Blades improperly installed. 10.Improper blades used. 11 .Clo ...

  • Craftsman 917.27206 - page 33

    TRACTOR - - MODEL NUMBER 917.272060 SCHEMATIC IGNITION SWITCH BATtERy SOLENOID R_O (_ _ FUSE ' i (OPTIONAL) w_l_ i _ 1_ a_c_ CLUTCH / BRAKE r I (PEDAL UP) , ...... 4 ATYMENT CLUTCH i _-_ - (CLUTCH OFF) ;8-5 .... _, FUE_ SH_-OF_ '- -_ ...... SOLENOIO SEAT SWITCH (NOT OCCUPIED) _ OPERATOR PRESENCE RELAY #1 86; i OPERATOR ESENCE RELAY #2 SPA ...

  • Craftsman 917.27206 - page 34

    TRACTOR - - MODEL NUMBER 917.272060 ELECTRICAL 24 41 / t 34 ...

  • Craftsman 917.27206 - page 35

    TRACTOR -- MODEL NUMBER 917.272060 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 Battery 12 Volt 28 Amp 2 74760412 Bolt, Hex Head 1/4-20 uoc x 3/4 8 156417 Case, Battery Mech Hinge 16 161343 Switch, interlock N Opn/N Opn 21 166182 Harness, Light Socket (Includes 4152J) 22 4152J Bu;b, Light 24 4799J Cable, Battery, 6 Gauge, Red, 11" 25 14614 ...

  • Craftsman 917.27206 - page 36

    TRACTOR -- MODEL NUMBER 917.272060 CHASSIS AND ENCLOSURES 3 74 44 I 2O6 ...

  • Craftsman 917.27206 - page 37

    TRACTOR - - MODEL NUMBER 917.272060 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 169830 Chassis Stamping 2 169061 Dmwber 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X013 Dash 10 STD533710 Bolt, Carrlage 3/8-16xl 11 155927 Panel, Dash, L.H. 12 145660 Clip TInnetman Gttlle P/L 13 172107X010 Panel, Dash, R.H, 17 144963X558 ...

  • Craftsman 917.27206 - page 38

    TRACTOR -- MODEL NUMBER 917.272060 GROUND DRIVE ...

  • Craftsman 917.27206 - page 39

    TRACTOR -- MODEL NUMBER 917.272060 GROUND DRIVE KEY PART KEY NO, NO. DESCRIPTION NO. 1 ...... Transaxle (See BreakdOwn) _5 Hydro Gr 314-0510 66 8 165866 Rod Shift Fender Adjust 70 10 ST[To61210 PInCotter 1/8xl CAD 71 14 10040400 Washer LOCkH W Helical 72 15 74490544 BOlt Hex FLGHD 5/16-18 x Gr 5 73 16 STD541431 Nut Lock Hex W/Ins. 5/16-18 Unc 74 19 ...

  • Craftsman 917.27206 - page 40

    TRACTOR -- MODEL NUMBER 917.272060 STEERING ASSEMBLY ,- L 11 4o 2 _29 40 ...

  • Craftsman 917.27206 - page 41

    TRACTOR -- MODEL NUMBER 917.272060 STEERING ASSEMBLY KEY PART NO: NO. DESCRIPTION 1 139768 SteedngWheel 2 154427 Axle Assembly STMP Dropped STL 3 169840 Spindle Assembly, LH. 4 169839 Spindle Assembly, R.H. 5 6266H Beadng, Race, Thrust, Hardened 6 121748X Washer 23/32 x 1-5/8 x 16 Gauge 7 19272016 Washer 27/32 x 1-1/4 x 16 Gauge 8 12000029 Ring, Kl ...

  • Craftsman 917.27206 - page 42

    TRACTOR -- MODEL NUMBER 917.272060 ENGINE ! 38 1o! 31 /: _ 33 29 OPTIONAL EQUIPMENT Spark Arrester 8o i , :i i 42 ...

  • Craftsman 917.27206 - page 43

    TRACTOR - - MODEL NUMBER 917.272060 ENGINE KEY PART NO. NO. DESCRIPTION 1 170548 Contrbl, Throffie 2 17720410 Screw, Hex Head, Thread Cuffing 1/4-20 x 5/8 3 ...... Engine, (See Breakdown) Kobler ModelNo. CV460-26509 4 159420 Muffler 13 12-041-03 Gasket Kohier 14 148456 Tube Drain Oil Easy 16 ST[To51237 Washer 23 169837 Shield Sm/Dbr Guard 29 137180 ...

  • Craftsman 917.27206 - page 44

    TRACTOR -- MODEL NUMBER 917.272060 SEAT ASSEMBLY 8 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 140123 Seat 13 121248X Bushing, Snap 140551 Bracket, Pivot, Seat 14 72050412 Bo_tl Cardage 1/4-20 x %1/2 71110616 Bo_t 15 134300 Spacer, Split .28 x .88 19131610 Washer 13/32 x I x 10Gauge 16 12t250X Spdng 145006 C ...

  • Craftsman 917.27206 - page 45

    TRACTOR - - MODEL NUMBER 917.272060 DECALS 10 20 '12 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 156811 Decal, Oper. instr. 13 177336 Decal, Lower Dash 2 177368 Decal, HP Engine 14 160396 Decal, V-Belt Schema_c 3 171698 Decal, Hood, R.H. 16 138047 Decal. Battery Diehard 4 171699 Decal, Hood, LH. 20 149516 Decal, Battery Dngr/Pon ...

  • Craftsman 917.27206 - page 46

    TRACTOR -- MODEL NUMBER 917.272060 LIFT ASSEMBLY 13 3 2 6 5 4 19 13 ---,-_ _ 31 32 13 19 2O 46 ...

  • Craftsman 917.27206 - page 47

    TRACTOR - - MODEL NUMBER 917.272060 LIFT ASSEMBLY KEY PART NO. NO, DESCRIPTION 1 159460 [_If{ Lever Inner Wire Assembly 2 159471 Shaft ASSembly, Lilt 3 105767X Pin, Groove 4 120000(_ E-F_ng 5 19211621 Washer 21/32 x 1 x 21 Gauge 6 120183X Beadng, Nylon 7 125631X Grip, Handle, Fluted 8 122365X Button, Plunger, Red 11 139865 Link, Uft, L.H. 12 139866 ...

  • Craftsman 917.27206 - page 48

    TRACTOR -- MODEL NUMBER 917.272060 MOWER DECK 157 _ _/,_ 67 151 . ' 183 ISS _37 159-_ "44 _1505 .._ 105 106 102 103 102/_' 34 >21 119 5 6 118 16 1 48 ...

  • Craftsman 917.27206 - page 49

    TRACTOR - - MODEL NUMBER 917.272060 MOWER DECK KEY PART NO. NO, DESCRIPTION 1 165892 Mower Deck Assembly, 42" 2 STD533107 Belt 3 138017 Bracket Assembly,Sway Bar, Front 4 165460 Bracket Sway Bar 38/42" ack 5 STD_4C(_ Retsiner Spdng 6 130832 Arm, Suspension, Rear 8 850_57 Bolt, Hex 3/8-24 x 1.25 Gr. 8 9 STD551137 Washer, Lock 10 140296 WaS ...

  • Craftsman 917.27206 - page 50

    81 77 79 / 73 _, 82 17 32 93 58 48 124 107 o 0 °i mO a | oO m o , f- zl- 0_=_. °_ I0 0 ...

  • Craftsman 917.27206 - page 51

    TRACTOR - - MODEL NUMBER 917.272060 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 314-0510 KEY PART KEY PART NO. NO. DESCRIPTION NO, NO, DESCRIPTION 59 1704G6 Rotor, Brake 1 170_51 Main Housing, Assembly 60 142883 Brake PUCk 2 170352 Sibe Housing, Aseembly 61 142881 Puck Plate 3 170_53 Center Section, Assembly 62 142887 Brake Act_a_t_g Pk_ 4 170354 Swashpl ...

  • Craftsman 917.27206 - page 52

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CYLINDER HEAD, VALVE AND BREATHER I I j" 18 19 CRAHKCASEJ 1 19 18 10 52 ...

  • Craftsman 917.27206 - page 53

    TRACTOR o- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CYLINDER HEADNALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO. DESCR_TION NO. NO. DESCRIP_ON 25-351-01-S • 12-755-94-S 1 Lifter, valve (2) 2 Kit, cylinder head (Includes 3-17, Gaskets 12 041 01-S (Qty. 2),12 041 02- S, & 12 041 03-S 3 Rod, push (2 4 Gasket ...

  • Craftsman 917.27206 - page 54

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 IGNITIONIELECTRICAL BLOWER HOUSING AND BAFFLES I I 3 4 s V AiR INTAKE I _'-s I- m7 54 ...

  • Craftsman 917.27206 - page 55

    TRACTOR - - MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 IGNITION/ELECTRICAL KEY PART NO. NO, DESCRIPTION BLOWER HOUSING & BAFFLES KEY PART NO. NO, DESCRIPTION 1 12-086-14-S Screw, hex. flange M10x1.5x46 1 M-545010-S Screw, hex. flange 2 12-468-03-S Washer, plain 3/8' M5x0.8xl0 (4) 3 24-162-03-S Screen, grass ...

  • Craftsman 917.27206 - page 56

    TRAC_R -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, _PE NUMBER 26509 STARTING SYSTEM 1 I m 0 tF 8 !]-- ENGINE CONTROLS I 1 11 2 4 OiL PAN I LUBRICATION I 1 ?--1o -_3 tl S q _ 20 7" t6 O/16 1C2..', 56 ...

  • Craftsman 917.27206 - page 57

    TRACTOR - - MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 STARTING SYSTEM ENGINE CONTROLS KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 2 8) 3 12-755o39-S Kit, drive end 4 12-227o03-S Cap, drive end 5 12-170-04-S Armature 6 12-755-38-S Kit, drive parts 7 12-243-O4-S Cap, commutator end 8 12-086-20-S Screw, ...

  • Craftsman 917.27206 - page 58

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CRANKSHAFT I EXHAUSTJ --1 FUELSYSTEM I ,7 II _ jll I /7 6 --lo 58 ...

  • Craftsman 917.27206 - page 59

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 FUEL SYSTEM KEY PART NO. NO. DESCRIPTION 1 M-641060-S Nut, hex. flange M6xl.O (2) 2 X-22-11-S Washer, lock 1/4" 3 M-629116-S Stud M6x1.0x116 (2) 4 12-853-115-S Kit, carburetor w/gasket (Includes 5,6,7 qty 1) 5 12-041-02-S Gasket, air cleaner 6 12-653-115 Car ...

  • Craftsman 917.27206 - page 60

    60 ...

  • Craftsman 917.27206 - page 61

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL d A Operate your Tractor up and down the face of slopes (not i i AUk grseter thon15"), never acrons the face. Maketumsgradu- I | _ ally to prevent tipping or loss of control, Exercise extreme I / caution when changing direction on slopes. ( I! ...

  • Craftsman 917.27206 - page 62

    62 ...

  • Craftsman 917.27206 - page 63

    63 ...

  • Craftsman 917.27206 - page 64

    Get it fixed, at your home or ours! For repair of major brand appliances In your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM A.ytime, Say or night (1-80o469-4e63) www.sesrB.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Seers Parts & Rep ...

Manufacturer Craftsman Category Lawn Mower

Documents that we receive from a manufacturer of a Craftsman 917.27206 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 917.27206 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 917.27206
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 917.27206.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 917.27206, service manual, brief instructions and user manuals Craftsman 917.27206. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 917.27206.

Similar manuals

A complete manual for the device Craftsman 917.27206, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 917.27206 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 917.27206.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 917.27206 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 917.27206, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 917.27206, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 917.27206 - which should help us in our first steps of using Craftsman 917.27206
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 917.27206
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 917.27206 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 917.27206?

Use the form below

If you did not solve your problem by using a manual Craftsman 917.27206, ask a question using the form below. If a user had a similar problem with Craftsman 917.27206 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)