English dropdown-ico

Manual Apple Xserve 073-0711

13 pages 2.46 mb
Download

Go to site of 13

Summary
  • Apple Xserve 073-0711 - page 1

    073-0711 Re v . B  Xserve Logic Board with Processor/Heatsink Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Online instructions cov ering customer-installable par ts are av ailab le at http://www .info .apple.com/inst ...

  • Apple Xserve 073-0711 - page 2

    Xserve Logic Board with Processor/Heatsink - 2 3. If the ser v er is in the loc k ed position (the y ello w security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 4. If the cable management arm is not in use, unplug all e xternal cables e xcept the pow er cord. 5. T ouch the ser v er’ s metal case to d ...

  • Apple Xserve 073-0711 - page 3

    Xserve Logic Board with Processor/Heatsink - 3 8. Grasp the thumbscre ws and slide the bottom housing f orward part wa y to e xpose the two chassis le v ers . (Figure 2) 9. While depressing both le v ers , pull the bottom housing all the w a y forw ard and remo v e it from the rac k. Figure 2 10. Place the bottom housing on a sturdy , flat surf ac ...

  • Apple Xserve 073-0711 - page 4

    Xserve Logic Board with Processor/Heatsink - 4 Removing the Installed Logic Board Note: The replacement logic board does not include memor y DIMMs or expansion cards . Y ou must tr ansf er these par ts from the current logic board. T o remov e the logic board, y ou must first remov e: • memory DIMMs • PCI/AGP card risers • heatsink duct • ...

  • Apple Xserve 073-0711 - page 5

    Xserve Logic Board with Processor/Heatsink - 5 Dual-Slot Riser 1. Release the thumb screw that secures the card to the bac k of the server . (Figure 4) 2. Disconnect the riser from the logic board and remov e the riser from the ser ver . Figure 4 Single-Slot Riser 1. Release the thumb screw that secures the card to the bac k of the server . (Figure ...

  • Apple Xserve 073-0711 - page 6

    Xserve Logic Board with Processor/Heatsink - 6 2. Pull the clip on the riser forw ard to release the riser from the logic board connector . (Figure 6) 3. Disconnect the riser from the logic board and remov e the riser and card from the ser v er . Figure 6 Heatsink Duct 1. Release the latch on the heatsink duct from its slot, slide the duct aw a y f ...

  • Apple Xserve 073-0711 - page 7

    Xserve Logic Board with Processor/Heatsink - 7 A T A Controller Board 1. Disconnect the blo wer cab le nearest the A T A controller board. (Figure 8) 2. Press in on both ends of the clip securing the r ight side of the A T A controller board and remov e the clip from the server . Repeat f or the clip on the left side of the board. 3. Lift the A T A ...

  • Apple Xserve 073-0711 - page 8

    Xserve Logic Board with Processor/Heatsink - 8 P ower Supply 1. Release the locking latch on the po wer supply cab le connector and disconnect the cable from the driv e interconnect board. (Figure 9) 2. Release the thumbscrew that secures the po wer supply to the chassis . Note: The thumbscrew is captive; you cannot remove it. 3. Grasp the metal ? ...

  • Apple Xserve 073-0711 - page 9

    Xserve Logic Board with Processor/Heatsink - 9 Logic Board 1. Release the thumb screw that secures the logic board to the chassis . (Figure 10) 2. Mov e the logic board f orw ard and up slightly to release it from the f our mounting pegs. 3. Tilt up the end of the logic board nearest the blo wers so that the board ports clear the chassis. 4. Remov ...

  • Apple Xserve 073-0711 - page 10

    Xserve Logic Board with Processor/Heatsink - 10 2. Install the replacement logic board in the bottom housing, making sure the board fits ov er the f our mounting pegs on the chassis floor . W arning: When replacing the logic board, make sure the ports and the identifier button on the bac k of the boar d align with the openings in the chassis. 3. ...

  • Apple Xserve 073-0711 - page 11

    Xserve Logic Board with Processor/Heatsink - 11 8. Reinstall the two A T A controller clips. Note: When replacing the ATA controller board clips, orient them so that the long end of each clip points away from the middle of the server. Place the inside edge of the clip into the small notch and then snap down the outer edge of the clip. (Figure 13) F ...

  • Apple Xserve 073-0711 - page 12

    Xserve Logic Board with Processor/Heatsink - 12 12. Remov e the battery insulator tab from the batter y holder on the replacement logic board. (Figure 14) Figure 14 Note: Replacing the logic board in the ser v er changes its Ethernet ID number . The new number is printed on an Ether net ID label pac kaged with the replacement logic board. After ins ...

  • Apple Xserve 073-0711 - page 13

    Xserve Logic Board with Processor/Heatsink - 13  Apple Computer , Inc. © 2002 Apple Computer , Inc. All rights reser v ed. This document is protected under U .S . Cop yright Law and Inter national T reaties, and no par t of this document ma y be reproduced in any f orm without written per mission from Apple. Apple is not responsible f or typogr ...

Manufacturer Apple Category Network Card

Documents that we receive from a manufacturer of a Apple Xserve 073-0711 can be divided into several groups. They are, among others:
- Apple technical drawings
- Xserve 073-0711 manuals
- Apple product data sheets
- information booklets
- or energy labels Apple Xserve 073-0711
All of them are important, but the most important information from the point of view of use of the device are in the user manual Apple Xserve 073-0711.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Apple Xserve 073-0711, service manual, brief instructions and user manuals Apple Xserve 073-0711. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Apple Xserve 073-0711.

Similar manuals

A complete manual for the device Apple Xserve 073-0711, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Apple Xserve 073-0711 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Apple Xserve 073-0711.

A complete Apple manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Apple Xserve 073-0711 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Apple Xserve 073-0711, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Apple Xserve 073-0711, that we can find in the current document
3. Tips how to use the basic functions of the device Apple Xserve 073-0711 - which should help us in our first steps of using Apple Xserve 073-0711
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Apple Xserve 073-0711
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Apple Xserve 073-0711 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Apple Xserve 073-0711?

Use the form below

If you did not solve your problem by using a manual Apple Xserve 073-0711, ask a question using the form below. If a user had a similar problem with Apple Xserve 073-0711 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)