Manual Hearth and Home Technologies RCT-MLT-II

11 pages 0.34 mb
Download

Go to site of 11

Summary
  • Hearth and Home Technologies RCT-MLT-II - page 1

    1 Printed in U.S.A. Copyright 2008, Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 100-907F 4/08 RCT -ML T -II Remote Control Kits - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostati- cally or manually from the transmitter . The system oper- ates on rad ...

  • Hearth and Home Technologies RCT-MLT-II - page 2

    2 Figure 1 REMOTE RECEIVER Important: The remote receiver should be positioned close to front in right or left corner where ambient temperatures do not exceed 170º F . The remote receiver is powered by 1 10-120V AC. It plugs into a standard polarized duplex receptacle. Locating Receiver and Operating Functions This remote receiver can be positione ...

  • Hearth and Home Technologies RCT-MLT-II - page 3

    3 Figure 4. Figure 5. VARIABLE REGULATOR GAS CONTROL VALVE FLAME CONTROL SOLENOI D KNOB SCREW NUT VARIABLE REGULATOR JAM NUT VARIABLE REGULATOR SOLENOID WASHER WASHER PLUNGER Installing Flame Control Solenoid 1. Remove the screw and knob from the variable regula- tor and discard. 2. Unscrew the nut from the regulator and discard. 3. Remove the bag ...

  • Hearth and Home Technologies RCT-MLT-II - page 4

    4 The remote receiver has a 3-position slide switch: OFF/ REMOTE/ON (see Figure 6). Figure 6. Remote Receiver TRANSMITTER Important: Before operating remote control, transmit- ter and receiver must have matching security codes. See section ‘Matching Security Codes’. Important: Review ‘Thermo-Updating/Communication- Safety Features’ under ? ...

  • Hearth and Home Technologies RCT-MLT-II - page 5

    5 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer . T o program the remote receiver: 1. Set the slide button on the receiver to the REMOTE position. 2. Push the LEARN button ( ...

  • Hearth and Home Technologies RCT-MLT-II - page 6

    6 Figure 8. Setting Button/Child Proof Lockout Setting ºF/ºC Scale The factory setting for temperature is degrees Fahrenheit ( ºF). T o change this setting to degrees Centigrade (ºC): 1. Remove the battery cover on the back of the transmit- ter and locate the “setting button” at the top center of battery compartment (see Figure 8). 2. Push ...

  • Hearth and Home Technologies RCT-MLT-II - page 7

    7 Adjusting the Flame Height - Operates in ON or THERMO mode This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER. 1. Press and release FLAME button to change fl ame height to HI (see Figure 7, Location #5), (a second fl ame icon appears). 2. Press again to re ...

  • Hearth and Home Technologies RCT-MLT-II - page 8

    8 6. Advance the SET temperature on the transmitter to a temperature of at least 2º F (1º C) above the ROOM temperature displayed on the LCD screen and the system fl ame will ignite. 7. Set the SET temperature to at least 2º F (1º C) below the room temperature and the system fl ame will extin- guish. Thereafter, it should continue to cycle on ...

  • Hearth and Home Technologies RCT-MLT-II - page 9

    9 Figure 9. Intermittent Pilot Ignition (IPI) Wiring Diagram Figure 10. Standing Pilot Ignition Wiring Diagram TRAN SF ORMER 3V A C PLUG I N R E D BA T TERY P ACK THER MO ST A T WIRE AS SEMBL Y JUMPER WIRE (TO BROW N) ORA NG E GREE N VA LV E GR OU ND TO FIR EPLAC E CHA SSIS WHIT E OR A NGE IGNITION MO DULE 3 V AC INTERMITTENT PILOT IGNITOR HOT NEUT ...

  • Hearth and Home Technologies RCT-MLT-II - page 10

    10 Figure 12. Standing Pilot Ignition Wiring Diagram Figure 1 1. Intermittent Pilot Ignition (IPI) Wiring Diagram BLACK S2 ON OFF ON/OFF SWIT CH WHITE T2 RED T1 THERMO PILE GAS V AL UE BLACK S1 3/16” PIGGYBACK CONNECTOR THERMOCOUPLE REMOTE SWITCH PI GT AIL OPTI ONA L W ALL SWI TCH, THERMOST A T OR REMOTE IGN ITION MOD ULE 3V A C TRANSFO RMER 3V A ...

  • Hearth and Home Technologies RCT-MLT-II - page 11

    11 Figure 14. Remote Control Standing Pilot Ignition Wiring Diagram Figure 13. Remote Control Intermittent Pilot Ignition (IPI) Wiring Diagram Remote Control Wiring Diagrams V ALVE GREEN ORANGE JUMPER WIRE (TO BROWN) PLUG IN TRANSFORMER 3 VAC B L A C K R E D GROUND TO FIREPLACE CHASSIS WHITE ORANGE INTERMITTENT PILOT IGNITOR IGNITION MODULE 3 VAC R ...

Manufacturer Hearth and Home Technologies Category Universal Remote

Documents that we receive from a manufacturer of a Hearth and Home Technologies RCT-MLT-II can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- RCT-MLT-II manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies RCT-MLT-II
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies RCT-MLT-II.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies RCT-MLT-II, service manual, brief instructions and user manuals Hearth and Home Technologies RCT-MLT-II. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies RCT-MLT-II.

A complete manual for the device Hearth and Home Technologies RCT-MLT-II, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies RCT-MLT-II by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies RCT-MLT-II.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies RCT-MLT-II - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies RCT-MLT-II, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies RCT-MLT-II, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies RCT-MLT-II - which should help us in our first steps of using Hearth and Home Technologies RCT-MLT-II
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies RCT-MLT-II
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies RCT-MLT-II in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies RCT-MLT-II?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies RCT-MLT-II, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies RCT-MLT-II it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)