English dropdown-ico

Manual Harbor Freight Tools 90178

19 pages 3.04 mb
Download

Go to site of 19

Summary
  • Harbor Freight Tools 90178 - page 1

    CEMENT MIXER - 3.5 CUBIC FOOT WITH BRIGGS & STRA TT ON 3.5 HP ENGINE Model 90178 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .harborfreight.com Copyright 2003 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may ...

  • Harbor Freight Tools 90178 - page 2

    PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover . Keep this manual and invoice in a safe a ...

  • Harbor Freight Tools 90178 - page 3

    6. Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, back injury , etcetera. 7. Industrial applications must follow OSHA requirements. 8. Stay alert. W atch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand. 9. Check for damaged ...

  • Harbor Freight Tools 90178 - page 4

    3. Keep a safe clearance around the Cement Mixer . Keep all people (except the operator) a minimum of six feet from the Mixer during operation. 4. Keep all guards in place and in proper working condition. 5. Remove adjusting tools, shovels, hand trowels, etc. Make sure all adjusting tools, shovels, hand trowels, and other tools and equipment are re ...

  • Harbor Freight Tools 90178 - page 5

    Dispose of fluids and cleaning materials in accordance with all local, state, or federal codes and regulations. Store oil rags in a covered metal container . 17. Never store fuel or other flammable materials near the Cement Mixer . 18. Do not smoke, or allow sparks, flames, or other sources of ignition around the Engine (part #14) and its fuel tank ...

  • Harbor Freight Tools 90178 - page 6

    SKU 90178 P AGE 6 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts List on page 18 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y INSTRUCTIONS NOTE: For additional references to the parts listed in the fo ...

  • Harbor Freight Tools 90178 - page 7

    SKU 90178 P AGE 7 WHEEL (#5) PIN (#4) FLA T W ASHER (#3) FIGURE B W ashers (part #10), two Spring Washers (part #9), and two Nuts (part #8). (See Figure C.) HEX BOL T (#7) FLA T W ASHER (#10) SPRING W ASHER (#9) NUT (#8) HEX BOL T (#7) FLA T W ASHER (#10) SPRING W ASHER (#9) NUT (#8) LOWER DRUM (#44) SUPPORT ARM (#31) FIGURE C 4. Align the two moun ...

  • Harbor Freight Tools 90178 - page 8

    HEX HEAD BOL T (#27) FLA T W ASHER (#10) NOT SHOWN SPRING W ASHER (#9) NOT SHOWN NUT (#8) NOT SHOWN DEGREE ADJUSTING PLA TE (#37) DEGREE ADJUSTING ARM (#38) SPRING (#39) BOL T (#40) NUT (#8) PIVOT ARM OF DEGREE ADJUSTING PLA TE (#37) FIGURE D 6. Secure the Degree Adjusting Arm (part #38) to the Pivot Shaft of the Degree Adjusting Plate (part #37), ...

  • Harbor Freight Tools 90178 - page 9

    7. Align the six mounting holes of the Connector Seal (part #45) with the six mount- ing holes in the Upper Drum (part #47). Then, glue (not included) the Connector Seal to the Upper Drum. NOTE: Make sure the Connector Seal lays flat on the Upper Drum to ensure a proper seal. (See Figure E.) UPPER DRUM (#47) CONNECTOR SEAL (#45) MOUNTING HOLE FIGUR ...

  • Harbor Freight Tools 90178 - page 10

    SKU 90178 P AGE 10 Flat W ashers (part #10), four Spring W ashers (part #9), and four Nuts (part #50) to secure the two Mixing Blades to the inside Drum assembly . (See Figure G.) MIXING BLADE (#46) MOUNT WITH V-SHAPED BENDS POINTING TO LEFT . DRUM ASSEMBL Y (#44, #47) FIGURE G 1 1. Insert the Fixing Plate (part #18) onto the Shaft (part #35). (See ...

  • Harbor Freight Tools 90178 - page 11

    FIGURE I SHAFT (#35) FIXING PLA TE (#18) FIGURE J INNER COVER (#23) SHAFT (#35) SKU 90178 P AGE 1 1 14. Align the four mounting holes in the Engine Mount Plate (part #12) with the two mounting slots located in the lower portion of the Inner Cover (part #23). Position the Small Fixing Plate (part #51) against the vertical arm of the Stand (part #1). ...

  • Harbor Freight Tools 90178 - page 12

    HEX HEAD BOL T (#27) FLA T W ASHER (#19) SPRING W ASHER (#20) NUT (#21) HEX HEAD BOL T (#27) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#21) BOL T (#48) FLA T W ASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WA ...

  • Harbor Freight Tools 90178 - page 13

    16. Unscrew the Thrust Screw (part #17) located in the Large Pulley (part #26). Align the Keyway Slot of the Large Pulley with the Key on the Shaft (part #35). Using a hammer , carefully tap the Large Pulley onto the Shaft. Retighten the Thrust Screw to secure the Large Pulley in place. (See Figure M.) FIGURE M LARGE PULLEY (#26) SHAFT (#35) 17. Lo ...

  • Harbor Freight Tools 90178 - page 14

    18. Align the four mounting holes in the base of the Engine (part #14) with the four mounting slots in the Engine Mount Plate (#12). Insert four Hex Bolts (part #7) downward through the mounting holes and mounting slots. Insert one Flat W asher (part #10) and one Spring W asher (part #9) on each of the four Bolts. Then, finger tighten only one Nut ...

  • Harbor Freight Tools 90178 - page 15

    OPERA TING INSTRUCTIONS 1. IMPORT ANT : AL W A YS make sure the crankcase of the gasoline Engine (part #14) is filled to the proper level with a premium quality , 30-weight, non-detergent engine oil prior to starting the engine. Failure to do so will result in damage to the Engine and void its warranty . Refer to the Engine manufacturer ’s instru ...

  • Harbor Freight Tools 90178 - page 16

    SKU 90178 P AGE 16                        ? ...

  • Harbor Freight Tools 90178 - page 17

    1 1. After discharging the cement mix, raise the Degree Adjusting Arm (part #38) up to its original position. (See Figure Q.) 12. Repeat Steps #5 through #1 1 if more cement mix is required. 13. When finished, make sure to thoroughly clean the inside of the Drum (parts #44, #47). (See “Inspection, Maintenance, And Cleaning” Section.) SKU 90178 ...

  • Harbor Freight Tools 90178 - page 18

    NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90178 P AGE 18 P ARTS LIST * See Briggs & Stratton Engine Parts List and Assembly Diagram for available replacement parts. ® PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED T ...

  • Harbor Freight Tools 90178 - page 19

    ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90178 P AGE 19 51: SMALL FIXING PLA TE NOT SHOWN. ...

Manufacturer Harbor Freight Tools Category Window

Documents that we receive from a manufacturer of a Harbor Freight Tools 90178 can be divided into several groups. They are, among others:
- Harbor Freight Tools technical drawings
- 90178 manuals
- Harbor Freight Tools product data sheets
- information booklets
- or energy labels Harbor Freight Tools 90178
All of them are important, but the most important information from the point of view of use of the device are in the user manual Harbor Freight Tools 90178.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Harbor Freight Tools 90178, service manual, brief instructions and user manuals Harbor Freight Tools 90178. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Harbor Freight Tools 90178.

Similar manuals

A complete manual for the device Harbor Freight Tools 90178, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Harbor Freight Tools 90178 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Harbor Freight Tools 90178.

A complete Harbor Freight Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Harbor Freight Tools 90178 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Harbor Freight Tools 90178, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Harbor Freight Tools 90178, that we can find in the current document
3. Tips how to use the basic functions of the device Harbor Freight Tools 90178 - which should help us in our first steps of using Harbor Freight Tools 90178
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Harbor Freight Tools 90178
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Harbor Freight Tools 90178 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Harbor Freight Tools 90178?

Use the form below

If you did not solve your problem by using a manual Harbor Freight Tools 90178, ask a question using the form below. If a user had a similar problem with Harbor Freight Tools 90178 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)