Manual Clarion APX200

16 pages 0.25 mb
Download

Go to site of 16

Summary
  • Clarion APX200 - page 1

    OPERATIONAL INSTALLATION MANUAL ...

  • Clarion APX200 - page 2

    APX200.2M Power System Amplifier INTRODUCTION The Clarion APX200.2M is a full-featured two-channel amplifier incorporating the following features: • Full frequency response with low distortion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, inclu ...

  • Clarion APX200 - page 3

    OWNER’S MANUAL 1 DESCRIPTION The Clarion APX200.2M two-channel amplifier provides 2x70 watts of power into a 4 ohm load and 2x110 watts of power into a 2 ohm load. This full featured model is an excellent choice for a variety of marine audio sound system configurations. The APX200.2M uses an unregulated MOSFET power supply for superior control of ...

  • Clarion APX200 - page 4

    APX200.2M Power System Amplifier 2 • Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier's range, 250mV to 2.5V for RCA inputs or 500mV to 5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Contro l- The amplifier also features a &quo ...

  • Clarion APX200 - page 5

    OWNER’S MANUAL 3 CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX200.2M contains power and speaker connections as shown below. Figure 2 1. Left Speaker Output 2. Right Speaker Output 3. Remote Turn-on Input 4. Ground Input 5. Battery + 12V Input 6. 25 Amp Fuse ...

  • Clarion APX200 - page 6

    APX200.2M Power System Amplifier 4 APPLICATIONS The Clarion APX200.2M 2-channel marine audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged - Mono Subwoofer System Set X-Over Mode to LP and adjust FREQ to speaker specifications. Figure 3 - In this application the amplifi ...

  • Clarion APX200 - page 7

    OWNER’S MANUAL 5 2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or satellite or subwoofer) speakers. NOTE: A passive crossover must be used with satellite speakers. Set X-Over Mode as shown. Set X-Over Mode a ...

  • Clarion APX200 - page 8

    APX200.2M Power System Amplifier 6 Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) Subwoofer 4 Ohms NOTE: Chart values based on 4 Ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave crossover at specified frequencies. Use co ...

  • Clarion APX200 - page 9

    OWNER’S MANUAL 7 INSTALLATION This section lists Mounting and Wiring Precautions for installing a Clarion APX200.2M marine amplifier. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yours ...

  • Clarion APX200 - page 10

    APX200.2M Power System Amplifier 8 5. Add an external fuse on the amplifier's positive (+) power lead and connect it as close as possible to the vessel's (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external f use will protect the electrical system f ...

  • Clarion APX200 - page 11

    OWNER’S MANUAL 9 Figure 6 - Electrical connections for the APX200.2M ...

  • Clarion APX200 - page 12

    APX200.2M Power System Amplifier 10 SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. Turn the Gain Control all the way counter-clockwise. 2. Turn the vessel's Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON p ...

  • Clarion APX200 - page 13

    OWNER’S MANUAL 11 FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay, slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting. Depending on your system design, the levels may become ...

  • Clarion APX200 - page 14

    APX200.2M Power System Amplifier 12 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check pola ...

  • Clarion APX200 - page 15

    OWNER’S MANUAL 13 NOTES ...

  • Clarion APX200 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX200.2M-10 Rev.1 (03/01) ...

Manufacturer Clarion Category Stereo Amplifier

Documents that we receive from a manufacturer of a Clarion APX200 can be divided into several groups. They are, among others:
- Clarion technical drawings
- APX200 manuals
- Clarion product data sheets
- information booklets
- or energy labels Clarion APX200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Clarion APX200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Clarion APX200, service manual, brief instructions and user manuals Clarion APX200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Clarion APX200.

Similar manuals

A complete manual for the device Clarion APX200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Clarion APX200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Clarion APX200.

A complete Clarion manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Clarion APX200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Clarion APX200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Clarion APX200, that we can find in the current document
3. Tips how to use the basic functions of the device Clarion APX200 - which should help us in our first steps of using Clarion APX200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Clarion APX200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Clarion APX200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Clarion APX200?

Use the form below

If you did not solve your problem by using a manual Clarion APX200, ask a question using the form below. If a user had a similar problem with Clarion APX200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)