English dropdown-ico

Manual Porter-Cable 324MAG

15 pages 0.73 mb
Download

Go to site of 15

Summary
  • Porter-Cable 324MAG - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable 324MAG - page 2

    2 SAFETY GUIDELINES - DEFINITIONS indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,may result in minor or moderate inju ...

  • Porter-Cable 324MAG - page 3

    3 3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the ris ...

  • Porter-Cable 324MAG - page 4

    4 ADDITIONAL SPECIFIC SAFETY RULES SERVICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance Section of this manual. Use of unauthorize ...

  • Porter-Cable 324MAG - page 5

    5 z When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator. z If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and ju ...

  • Porter-Cable 324MAG - page 6

    6 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 vo ...

  • Porter-Cable 324MAG - page 7

    7 Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. 0 - 2 1 8 1 8 1 8 1 6 1 61 4 1 41 2 1 2 2 - 3 1 8 1 8 1 6 1 4 1 41 2 1 21 0 1 0 3 - 4 1 8 1 8 1 6 1 4 1 21 2 1 01 0 8 4-5 18 18 14 12 12 10 10 8 8 5-6 18 16 14 12 10 10 8 8 ...

  • Porter-Cable 324MAG - page 8

    2. While pressing the arbor lock button, extend the lever on the Quik- Change blade clamp (A) Fig. 2 and turn it counter-clockwise. 3. Remove the Quik-Change blade clamp, release the arbor lock button, and remove the outer blade flange. 4. Retract the telescoping guard (A) Fig. 3 and remove the blade. 8 DISCONNECT TOOL FROM POWER SOURCE. Fig. 2 Fig ...

  • Porter-Cable 324MAG - page 9

    9 The telescoping guard (A) Fig. 3 is a safety device important to your protection. Every time you use the saw, verify that the telescoping guard rotates freely and returns quickly and completely to its closed position. At least once a month, remove any accumulated debris (sawdust, pitch, etc.) from the area around the hub (B) of the telescoping gu ...

  • Porter-Cable 324MAG - page 10

    10 0° POSITIVE STOP The saw is equipped with an adjustable positive stop at 0°. Check the accuracy of this stop periodically. To adjust: 1. Loosen the bevel adjustment lever (A) Fig. 8, and position the base for a 0° cut. Confirm that the bevel-stop sleeve (B) Fig. 8 is against the 0° stop screw (C). 2. Turn the saw upside down, retract the tel ...

  • Porter-Cable 324MAG - page 11

    11 INSTALLING THE OPTIONAL RIP GUIDE 1. Insert the rip guide (A) Fig. 14 through the slots (B). Slide the guide in until it extends through the both slots in the sawbase. 2. Place the compression spring on the thumb screw (C) Fig. 14 (supplied with the rip guide), and thread into the hole in the saw base. DO NOT TIGHTEN. 3. Adjust the rip guide for ...

  • Porter-Cable 324MAG - page 12

    12 CROSS-CUTTING Cutting directly across the grain of a piece of lumber is called crosscutting. Position the work so that the cut will be on the left. RIPPING Cutting wood lengthwise is referred to as ripping. This operation is performed in the same manner as crosscutting with the exception of supporting the workpiece. If the workpiece is supported ...

  • Porter-Cable 324MAG - page 13

    13 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. FAILURE TO START Should your tool fail to ...

  • Porter-Cable 324MAG - page 14

    14 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter- Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter- Cable · ...

  • Porter-Cable 324MAG - page 15

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Saw

Documents that we receive from a manufacturer of a Porter-Cable 324MAG can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- 324MAG manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable 324MAG
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable 324MAG.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable 324MAG, service manual, brief instructions and user manuals Porter-Cable 324MAG. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable 324MAG.

Similar manuals

A complete manual for the device Porter-Cable 324MAG, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable 324MAG by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable 324MAG.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable 324MAG - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable 324MAG, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable 324MAG, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable 324MAG - which should help us in our first steps of using Porter-Cable 324MAG
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable 324MAG
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable 324MAG in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable 324MAG?

Use the form below

If you did not solve your problem by using a manual Porter-Cable 324MAG, ask a question using the form below. If a user had a similar problem with Porter-Cable 324MAG it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)