English dropdown-ico

Manual Husqvarna 500RTT

28 pages 2.91 mb
Download

Go to site of 28

Summary
  • Husqvarna 500RTT - page 1

    500R TT Owner's Manual ...

  • Husqvarna 500RTT - page 2

    2 • K eep children and pets aw ay . • Do not ov erload the machine capacity by attempting to till too deep at too f ast a rate. • Ne v er operate the machine at high speeds on slipper y surf aces. Look behind and use care when bac king. • Ne ver allo w bystanders near the unit. • Use only attachments and accessor ies approv ed by the manu ...

  • Husqvarna 500RTT - page 3

    3 CONGRA TULA TIONS on your purchase of a ne w tiller . It has been designed, en gi neered and manu f ac tured to give you the best pos sib le de penda bil ity and per fo r m ance. Should you e xper ience any prob lems you can not easily remedy , please contact your nearest authorized service center . W e hav e com pe tent, well-trained tech ni cia ...

  • Husqvarna 500RTT - page 4

    4 T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Standard wrench sizes are listed. (1) Utility knif e (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA T OR’S POSITION (See Fig. 1) When right or left hand is mentioned in this manual, it means when you are in the oper ating position (standing ...

  • Husqvarna 500RTT - page 5

    5 ASSEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. HANDLE ASSEMBL Y "UP" POSITION FIG. 4 UNP A CKING CART ON (See Fig. 2) CA UTION: Be careful of e xposed sta ples when handling or disposing of cartoning material. IMPORT ANT : WHEN UN PA C ...

  • Husqvarna 500RTT - page 6

    6 ASSEMBL Y SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA T OR REMO VE TILLER FROM CRA TE • Mak e sure shift lev er indicator is in “N” position (See Fig. 7) • Tilt tiller forw ard by lifting handle . Separate cardboard cov er from le veling shield. • Rotate tiller handle to the right and pull tiller out of car ton. CONNECT SHIFT ROD (See Fig ...

  • Husqvarna 500RTT - page 7

    7 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to familiarize y ourself with the location of various controls and adjustments. Sav e this manual f or future ref erence. These symbols may appear on y our Tiller or in literature supplied with the produc ...

  • Husqvarna 500RTT - page 8

    8 OPERA TION TILLING (See Fig. 11) • Release depth stake pin. Pull the depth stake up f or increased tilling depth. Place depth stake pin in hole of depth stake to loc k in position. • Place shift le ver indicator in tilling position. • Hold the dr ive control bar against the handle to star t tilling mov ement. Tines and wheels will both tur ...

  • Husqvarna 500RTT - page 9

    9 OPERA TION TURNING • Release the drive control bar . • Mov e throttle control to “SLOW” position. • Place shift lev er indicator in “F” (forw ard) position. Tines will not turn. • Lift handle to raise tines out of ground. • Swing the handle in the opposite direction you wish to tur n, being careful to keep f eet and legs awa y f ...

  • Husqvarna 500RTT - page 10

    10 OPERA TION • Soil conditions are impor tant for proper tilling. Tines will not readily penetrate dry , hard soil which may con trib ute to e xcessive bounce and diffi cult handling of your tiller . Hard soil should be mois tened before tilling; howe v er , e xtremely wet soil will “ball-up” or clump dur ing tilling. W ait until the soil i ...

  • Husqvarna 500RTT - page 11

    11 MAINTENANCE GENERAL RECOMMEND A TIONS The warranty on this tiller does not co ver items that ha ve been subjected to operator ab use or negligence. T o receiv e full value from the w arranty , the operator m ust main tain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller . Al ...

  • Husqvarna 500RTT - page 12

    12 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG FIG. 16 Disconnect spark plug wire before perf orming any maintenance (e xcept car bu re tor adjustment) to prevent accidental start ing of engine . Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit f or maintenance. Clean ...

  • Husqvarna 500RTT - page 13

    13 SER VICE AND ADJUSTMENTS CA UTION: Disconnect spark plug wire fr om spark plug and place wire where it cannot come into contact with plug. TILLER T O ADJUST HANDLE HEIGHT (See Fig. 18) Select handle height best suited f or your tilling conditions. Handle height will be diff erent when tiller digs into soil. • First loosen handle lock le ver . ...

  • Husqvarna 500RTT - page 14

    14 SER VICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION T O REPLA CE GROUND DRIVE BEL T (See Fig. 21) • Remov e belt guard (See “TO REMO VE BEL T GU ARD” in this section of this manual). • Remove old belt b y slipping off engine ...

  • Husqvarna 500RTT - page 15

    15 SER VICE AND ADJUSTMENTS FIG. 24 TINE REPLA CEMENT (See Figs. 22, 23, and 24) CA UTION: Tines are sharp. W ear gloves or other pr otection when han- dling tines. A badly worn tine causes your tiller to work harder and dig more shallow . Most impor tant, wor n tines cannot chop and shred organic matter as eff ectively nor b ur y it as deeply as g ...

  • Husqvarna 500RTT - page 16

    16 SER VICE AND ADJUSTMENTS ENGINE CARBURET OR The carburetor has been preset at the f actor y and ad just ment should not be necessar y . Howe v er , engine per fo r mance can be aff ected by dif fe r enc es in fuel, tem per a ture, al ti tude or load. If the carburetor does need ad just ment, contact your nearest authorized service center/de par ...

  • Husqvarna 500RTT - page 17

    17 Immediately prepare your tiller f or storage at the end of the season or if the unit will not be used f or 30 days or more . W ARNING: Never store the tiller with gasoline in the tank inside a build ing where fumes may reac h an open fl ame or spark. Allow the engine to cool bef ore storing in any en clo sure . TILLER • Clean entire tiller (S ...

  • Husqvarna 500RTT - page 18

    18 Will not start 1. Out of fuel. 1. Fill fuel tank . 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se veral min utes before attempting to start. 4. Dir ty air cleaner. 4. Clean or replace air cleaner cartr idge. 5. Water in fuel. 5. Drain fuel tank and carburetor , and refi ...

  • Husqvarna 500RTT - page 19

    19 REP AIR P AR TS TILLER - - MODEL NUMBER 500R TT(96093000100), PR ODUCT NUMBER 960 93 00-01 HANDLE ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 21 532 18 11-27 Handle 23 532 08 67-77 Screw , He x W asher Hd. Slotted #10-24 x 1/2 24 532 00 94-84 Clip 26 532 15 92-31 Cable, Clutch 27 873 90 04-00 Nut Hex Flange 1/4-20 unc 29 873 73 10-00 Nut, K eps #1 ...

  • Husqvarna 500RTT - page 20

    20 KEY P ART NO . NO . DESCRIPTION 1 873 51 05-00 Nut, K eps 5/16-18 2 810 04 06-00 W asher , Lock 3/8 3 873 22 06-00 Nut, Hex 3/8-16 4 532 17 01-27 Shield, Inner Belt Guard RT 5 532 16 43-29 Pin Spirol Flared 6 532 11 01-11 Lev er , Shift 7 872 11 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr . 5 8 532 00 87-00 Plate, Shift Indicator 9 532 08 67-77 Screw , ...

  • Husqvarna 500RTT - page 21

    21 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P AR TS TILLER - - MODEL NUMBER 500R TT(96093000100), PR ODUCT NUMBER 960 93 00-01 MAINFRAME, RIGHT SIDE 2 873 97 05-00 Locknut, He x, Flange 5/16-18 5 532 10 23-32 Brack et, Reinf orcement 7 532 10 21-73 Counter Weight, R.H. 8 810 04 06-00 W asher , Lock 3/8 9 873 22 06-00 ...

  • Husqvarna 500RTT - page 22

    22 12 13 15 16 14 9 9 8 5 18 23 22 21 19 18 3 2 31 7 6 5 4 11 10 29 30 28 18 32 33 34 18 48 60 24 44 18 42 43 41 49 40 39 37 38 37 50 36 20 25 27 35 25 24 44 51 58 53 52 53 transmission_19.5b KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .S. inches. 1 inch = 25.4 mm 1 532 18 85-54 T ransmission Assemb ly (In cludes K ey ...

  • Husqvarna 500RTT - page 23

    23 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 11 12 16 11 12 25 33 32 16 3 4 7 8 9 5 23 23 28 24 18 6 5 5 12 11 10 tine_shield_13_in 22 21 20 19 1 19 532 10 27-01 Gr ip 20 873 22 06-00 Nut, Hex 3/8-16 21 532 10 21-56 Stake, Depth 22 874 93 06-32 Bolt, Hex 3/8-16 x 2 23 532 00 44-40 Hinge 24 872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr . 5 25 532 ...

  • Husqvarna 500RTT - page 24

    24 2 11 11 10 9 9 4 4 5 34 3 3 1 2 1 1 1 9 9 8 tine_ipb_1 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 00 44-59 Tine, Outer , L.H. 2 532 13 26-73 Clevis Pin 3 532 00 65-54 Tine, Inner , L.H. 4 532 12 46-60 Retainer , Spring Zinc 5 532 13 27-27 Assembly , Hub and Plate , L.H. 8 874 61 06-16 Bolt, Hex 3/8-24 x 1 9 532 00 44-6 ...

  • Husqvarna 500RTT - page 25

    25 1 532 18 92-32 Decal, Blt Grd 2 532 18 92-35 Decal, Logo 3 532 18 61-77 Decal, CNTRL PNL 5 532 11 06-14 Decal, Hand Placement 6 532 10 21-80 Decal, Shift Indicator 7 532 16 23-84 Decal, W ar ning 8 532 18 92-33 Decal, Tineshield 9 532 12 00-76 Decal, W ar ning, Rotating Tines - - 532 19 42-46 Manual, Owner’ s (English) KEY P ART NO . NO . DESC ...

  • Husqvarna 500RTT - page 26

    26 SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Compan y (“Husqvarna”) warrants Husqvarna product to the original pur- chaser to be free from defects in material and workmanship from the date of purchase for the “W arranty P eriod” of the product as set f or th below: Lifetime W arranty: All tiller tines against breakage, trim ...

  • Husqvarna 500RTT - page 27

    27 SER VICE NO TES ...

  • Husqvarna 500RTT - page 28

    532 19 42-46 11.10.04 TR Printed in U.S .A. ...

Manufacturer Husqvarna Category Tiller

Documents that we receive from a manufacturer of a Husqvarna 500RTT can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 500RTT manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 500RTT
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 500RTT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 500RTT, service manual, brief instructions and user manuals Husqvarna 500RTT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 500RTT.

Similar manuals

A complete manual for the device Husqvarna 500RTT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 500RTT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 500RTT.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 500RTT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 500RTT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 500RTT, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 500RTT - which should help us in our first steps of using Husqvarna 500RTT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 500RTT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 500RTT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 500RTT?

Use the form below

If you did not solve your problem by using a manual Husqvarna 500RTT, ask a question using the form below. If a user had a similar problem with Husqvarna 500RTT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)