Manual Directed Electronics K10

16 pages 0.66 mb
Download

Go to site of 16

Summary
  • Directed Electronics K10 - page 1

    NO TE: This product is intended for installation b y a prof essional installer only! Any attempt to install this product by an y person other than a trained prof essional may result in se v ere damage to a vehicle’ s electrical system and components. Model K10 installation guide ...

  • Directed Electronics K10 - page 2

    3 table of contents primary harness (H1) wire connection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness (H1) wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness wire descriptions . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Directed Electronics K10 - page 3

    4 primary harness (H1) wire connection guide primary harness (H1) wiring diagram The primar y harness supplied with this unit is the standard 12-pin harness used. T wo wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging and exchanging control units and connecting the necessar y wires to th ...

  • Directed Electronics K10 - page 4

    5 H1/2 WHITE (-) Parking Light Output This wire provides a (-) 200mA output to flash the parking lights. This is suitable for driving (-) light control wires in T oyota, Lexus, BMW , some Mitsubishi, some Mazda, etc. If the vehicle has a positive parking light circuit, a relay must be used to flash the parking lights. H1/3 WHITE/BLUE (-) Channel 3 ...

  • Directed Electronics K10 - page 5

    6 H1/6 BLUE (-) 200 mA Second Unlock Output The H1/6 BLUE output is used for progressive unlock. A progressive unlock system unlocks the driver's door when the unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again within 15 seconds after unlocking the driver's door . The BLUE wire ...

  • Directed Electronics K10 - page 6

    7 H1/11 RED (+)12V constant power input Before connecting this wire, remove the supplied fuse. Connect to the positive batter y terminal or the constant 12V supply to the ignition switch. N N O O T T E E : : Always use a fuse within 12 inches of the point you obtain (+)12V . Do not use the fuse in the har- ness for this purpose. This fuse protects ...

  • Directed Electronics K10 - page 7

    8 door lock harness (H4), wire connection guide ___ ___ ___ peripheral plug-in harnesses LED, 2-pin WHITE plug The LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make sure the LED wires are not shorted to ground as the LED will be damaged. Multiple LED’ s can be used, but they must be wired in series. The LED fits into a 9/3 ...

  • Directed Electronics K10 - page 8

    9 Pro Security Pr ogrammer interface, 3-pin port The BLACK three-pin port is provided for pr ogramming of the unit. When using the P ro Security P rogrammer , it is possible to configure any and all of the programmable functions. F or more information please refer to the guide packaged with the programmer . module programming The System Features Le ...

  • Directed Electronics K10 - page 9

    10 3. T ransmit. The transmitter is used to select the desired setting. As shipped, the unit is configured to the LED ON settings. These are the default settings. Pressing the lock button will set it to the LED ON setting. The LED will light solid (stop flashing) to indi- cate the setting. The horn will honk once (if connected). Pressing the unlock ...

  • Directed Electronics K10 - page 10

    11 system features menus feature descriptions 1 ACTIVE/P ASSIVE ARMING: When active arming is selected, the starter kill will ar m (if connected) only when the transmitter is used. When set to passive arming, the starter kill will ar m (if connected) 30 seconds after the ignition key is turned off. 2 CHIRPS ON/OFF: This feature controls the chirps ...

  • Directed Electronics K10 - page 11

    12 8 DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors. When the double pulse unlock feature is turned on, the BLUE H2/C wire will supply two nega- tive pulses instead of a single pulse. At the same time, the GREEN H2/A wire will supply two positive pulses instead of a single pulse. This makes it poss ...

  • Directed Electronics K10 - page 12

    13 Channels #4-6: Channels 4 through 6 are used to assign the arm, disarm and panic functions to sep- arate buttons on the remote control. T eaching a button to Channel 4 erases all information about that remote from memor y . Any auxiliar y functions that are desired will have to be reprogrammed. Similarly , if the remote is set up to use the sepa ...

  • Directed Electronics K10 - page 13

    14 remote configurations The transmitters can be programmed with the standard or single button arm/disarm configurations by using the Auto Learn functions in the Remote Coding. standard configuration A remote that uses the standard configuration operates similarly to many factor y keyless entry remotes. A standard configuration remote allows arming ...

  • Directed Electronics K10 - page 14

    15 power-up Power-up ensures that the when the system is powered up it will return to the same state it was in when power is disconnected. For a full description of power-up refer to the owner's manual. ...

  • Directed Electronics K10 - page 15

    16 3-Pin 2-Wire Door Lock Harness Override Switch Pro Secur ity Programmer ® ™ wiring quick reference guide ...

  • Directed Electronics K10 - page 16

    Get Started Get Protected Ungo Pro Security 661 W . Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2003 Directed Electroni cs, Inc . - All rights r eserved GK10 11-03 ...

Manufacturer Directed Electronics Category Network Card

Documents that we receive from a manufacturer of a Directed Electronics K10 can be divided into several groups. They are, among others:
- Directed Electronics technical drawings
- K10 manuals
- Directed Electronics product data sheets
- information booklets
- or energy labels Directed Electronics K10
All of them are important, but the most important information from the point of view of use of the device are in the user manual Directed Electronics K10.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Directed Electronics K10, service manual, brief instructions and user manuals Directed Electronics K10. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Directed Electronics K10.

A complete manual for the device Directed Electronics K10, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Directed Electronics K10 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Directed Electronics K10.

A complete Directed Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Directed Electronics K10 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Directed Electronics K10, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Directed Electronics K10, that we can find in the current document
3. Tips how to use the basic functions of the device Directed Electronics K10 - which should help us in our first steps of using Directed Electronics K10
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Directed Electronics K10
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Directed Electronics K10 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Directed Electronics K10?

Use the form below

If you did not solve your problem by using a manual Directed Electronics K10, ask a question using the form below. If a user had a similar problem with Directed Electronics K10 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)