Manual Epson D28144R

56 pages 4.4 mb
Download

Go to site of 56

Summary
  • Epson D28144R - page 1

    D28114, D28114N, D28131, D28140, D28144, D28144N Heavy-Duty Small Angle Grinders Petites meuleuses à renvoi d’angle de type industriel Esmeriladoras de ángulo pequeño para trabajo pesado INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ES ...

  • Epson D28144R - page 2

    English 1 IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D E WALT (1-800-433-9258) General Safety Rules – For All Tools WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE I ...

  • Epson D28144R - page 3

    English 2 PERSONAL SAFETY • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica- tion. A moment of inattention while operating power tools may result in serious personal injury. • Dress properly. Do not wear loose clothing or jewel ...

  • Epson D28144R - page 4

    English 3 • Always use proper guard with grinding wheel. A guard pro- tects operator from broken wheel fragments and wheel contact. • Accessories must be rated for at least the speed recom- mended on the tool warning label. Wheels and other acces- sories running over rated speed can fly apart and cause injury. Accessory ratings must be above li ...

  • Epson D28144R - page 5

    English 4 forces. Kickback forces can be controlled by the operator, if proper precautions are taken. • When wheel is binding, or when interrupting a cut for any reason, release the trigger and hold the unit motionless in the material until the wheel comes to a complete stop. Never attempt to remove the unit from the work or pull the unit backwar ...

  • Epson D28144R - page 6

    English 5 G1 A B C F I J FIG. 1 D28114 D28114N D28144 D28144N D28131 D28140 L K K switch must be cycled (turned off and on) to restart tool. The power will return to normal once the tool has cooled down to a suitable operating temperature. NOTE : Run the tool at no load to reduce the cool down time. COMPLETE ELECTRONIC CONTROL™ The internal elect ...

  • Epson D28144R - page 7

    English 6 ASSEMBLY AND ADJUSTMENTS ATTACHING SIDE HANDLE E The side handle (E) can be fitted to either side of the gear case in the threaded holes, as shown. Before using the tool, check that the handle is tightened se cure ly. Use a wrench to firmly tighten the side handle. Rotating the Gear Case WARNING: Turn off and unplug tool before making any ...

  • Epson D28144R - page 8

    English 7 4-1/2 " and 5 " Cutting Wheels Type 1 guard Quick-Change backing flange Type 1 abrasive cutting wheel threaded clamp nut Type 1 guard Quick-Change backing flange diamond cutting wheel threaded clamp nut 6" Cutting Wheels rubber backing pad sanding disc threaded clamp nut Sanding Discs Wire Wheels 3" wire cup brush 4&qu ...

  • Epson D28144R - page 9

    English 8 NOTE: If the gear case and motor housing become separated by more than 1/4", the tool must be serviced and re-assembled by a D E WALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure. 4. Re-install screws to attach the gear case to the motor hous- ing. Tighten screws to 18 in./lbs. torque. ...

  • Epson D28144R - page 10

    English 9 2. Push the guard down until the M O N guard lugs engage and rotate freely in the groove on the gear case hub. 3. With the guard latch open, rotate the guard (I) into the desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection. 4. Close the guard latch to se ...

  • Epson D28144R - page 11

    English 10 To turn the tool on, push the A B lock-off lever (B) toward the back of the tool, then depress the paddle switch (A). The tool will run while the switch is depressed. Turn the tool off by releasing the paddle switch. WARNING: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may start unexpectedly when it is ...

  • Epson D28144R - page 12

    English 11 MOUNTING NON-HUBBED WHEELS G1 D WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off. Depressed center Type 27 grinding wheels H must be used with included fl ...

  • Epson D28144R - page 13

    English 12 on page 7 for more information. Type 1 guards are available at extra cost from your local dealer or authorized service center. 1. Allow the tool to reach full speed before touching the tool to the work surface. 2. Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the to ...

  • Epson D28144R - page 14

    English 13 Begin with coarse grit discs for fast, rough material removal. Move to a medium grit paper and finish with a fine grit disc for optimal finish. Coarse 16 - 30 grit Medium 36 - 80 grit Fine Finishing 100 - 120 grit Very Fine Finishing 150 - 180 grit 1. Allow the tool to reach full speed before touching tool to the work surface. 2. Apply m ...

  • Epson D28144R - page 15

    English 14 6. Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before setting it down. CAUTION: Use extra care when working over an edge, as a sudden sharp movement of grinder may be experienced. Mounting and Using Cutting (Type 1) Wheels Cutting wheels include diamond wheels and abrasive discs. Abr ...

  • Epson D28144R - page 16

    English 15 2. Place the wheel on the backing flange, centering the wheel on the raised section (pilot). 3. Install the threaded clamp nut with the raised section (pilot) facing away from the wheel. 4. Depress the spindle lock button and tighten clamp nut with a wrench. 5. To remove the wheel, grasp and turn while depressing the spindl e lock button ...

  • Epson D28144R - page 17

    English 16 (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, D E WALT tools are covered by our: 1 YEAR FREE SERVICE D E ...

  • Epson D28144R - page 18

    Français 17 SI VOUS AVEZ DES QUESTIONS OU VOUS VOULEZ NOUS FAIRE PART DE VOS COMMENTAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL D E WALT, COMPOSEZ SANS FRAIS LE : 1-800-4-D E WALT (1-800-433-9258) Règles de sécurité – Généralités AVERTISSEMENT : Lire, comprendre et suivre toutes les directives précisées ci-dessous, y com- pris les con ...

  • Epson D28144R - page 19

    Français 18 illustre les calibres que l’on doit utiliser selon la longueur de la rallonge et l’intensité nominale indiquée sur la plaque signalé- tique. En cas de doute, utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut porter du courant. Calibre minimal des cordons de rallonge Tensi on Longueur totale du cordon ...

  • Epson D28144R - page 20

    Français 19 également les pièces afin de s’assurer qu’il n’y a aucun bris ni aucune autre condition susceptible de nuire au bon fonctionnement de l’outil. Faire réparer l’outil si ce dernier est endommagé avant de s’en servir à nouveau, car les accidents sont souvent causés par des outils mal entretenus. • N’utiliser que les ...

  • Epson D28144R - page 21

    Français 20 • Éviter de faire rebondir la meule ou de la traiter rudement. Dans ces cas, arrêter l’outil et inspecter la meule pour toute trace de fissure ou de fêlures. • Diriger les étincelles loin de l’opérateur, de personnes à proximité ou de matériaux inflammables. Il est possible de provoquer des étincelles lors d’ébavura ...

  • Epson D28144R - page 22

    Français 21 NIOSH/OSHA pour se protéger de la poussière. Diriger les parti- cules loin du visage et du corps. MISE EN GARDE : être plus attentif lors de travaux dans un coin. En effet, le contact inopiné de la meule ou d’un autre acces- soire sur une deuxième surface ou un rebord pourrait provoquer un mouvement brusque et soudain de la meul ...

  • Epson D28144R - page 23

    Français 22 sera tout simplement mis hors tension. Il est essentiel de réini- tialiser l’interrupteur (mettre sous et hors tension) pour redémarrer l’outil. L’outil fonctionnera à sa puissance normale une fois refroidi à une température de fonctionnement convenable. REMARQUE : faire tourner l’outil à vide pour réduire le temps de re ...

  • Epson D28144R - page 24

    Français 23 Capot protecteur pour meule de type 27 Meules de 114,3 mm et de 127 mm (4-1/2 et 5 po) Bride tournante sur collet battu à changement rapide écrou de serrage fileté Meule à moyeu intégré de type 27 Meule à moyeu déporté de type 27 Meules de 152 mm (6 po) Bride tournante sur collet battu à changement rapide en acier estampé é ...

  • Epson D28144R - page 25

    Français 24 Meules de 114,3 mm et de 127 mm (4-1/2 et 5 po) Capot protecteur pour meule de type 1 Bride tournante sur collet battu à changement rapide Disque de coupe de type 1 écrou de serrage fileté Capot protecteur pour meule de type 1 disque de coupe diamant écrou de serrage fileté Bride tournante sur collet battu à changement rapide Meu ...

  • Epson D28144R - page 26

    Français 25 ASSEMBLAGE ET RÉGLAGES ASSEMBLAGE DE LA POIGNÉE LATÉRALE E La poignée latérale (E) s’installe à droite ou à gauche dans les trous filetés du carter d’engrenages comme indiqué. Avant d’utiliser l’outil, vérifier si la poignée est solidement fixée. Utiliser une clé pour la fixer solidement. Disques de ponçage à lam ...

  • Epson D28144R - page 27

    Français 26 (7/8 po) de diamètre. Si non, l’accessoire pourrait être conçu pour une utilisation avec une scie circulaire et ne devrait pas être utili- sé. Utiliser uniquement les accessoires illustrés aux pages 23 à 25 du présent mode d’emploi. Les accessoires employés doivent être conçus pour des régimes supérieurs au régime min ...

  • Epson D28144R - page 28

    Français 27 REMARQUE : le meulage et le tronçonnage de chant peuvent s’effectuer à l’aide de meules de type 27 conçues et indiquées pour ce travail. AVERTISSEMENT : utiliser des accessoires prévus pour le régime minimum indiqué sur l’étiquette d’avertissement de l’outil. Les meules et les accessoires qui fonctionnent à un régim ...

  • Epson D28144R - page 29

    Français 28 Pour un fonctionnement en continu, L coulisser l’interrupteur vers l’avant de l’outil puis enfoncer la partie avant de l’interrupteur coulissant. Pour arrêter l’outil en mode de fonctionnement con- tinu, appuyer sur la partie arrière de l’interrupteur coulissant et le relâcher. BOUTON DE VERROUILLAGE (MODÈLES D28114 ET ...

  • Epson D28144R - page 30

    Français 29 Utiliser les brides fournies avec les meules à moyeu déporté de type 27. REMARQUE : la bride tournante sur collet battu à changement rapide en acier estampé (G2) s’utilise avec les modèles D28140, D28144 et D28144N pour les meules de type 27 seulement. Se reporter aux pages 23 à 25 pour de plus amples renseignements. 1. Sur la ...

  • Epson D28144R - page 31

    Français 30 MEULAGE DE CHANT AVEC DES MEULES ABRASIVES MISE EN GARDE : les meules utilisées pour le tronçonnage et le meulage de chant risquent de se briser si elles se plient ou se tordent en cours de tronçonnage ou de dégrossissage. Pour réduire le risque de blessures graves, limiter l’utilisation de ces meules, comportant un capot protec ...

  • Epson D28144R - page 32

    Français 31 MISE EN GARDE : une fois le H R S ponçage terminé, veuillez réinstaller le capot protecteur adéquat pour les opérations utilisant une meule, un disque de ponçage à lamelles, une brosse ou une meule métalliques. 1. Déposer ou visser le tampon (R) sur la broche. 2. Par la suite, insérer le disque abra- sif (S) sur le tampon. 3. ...

  • Epson D28144R - page 33

    Français 32 imperceptibles. Des fils pourraient se détacher de la brosse-bois- seau ou conique. ASSEMBLAGE DE BROSSES CONIQUES ET DE BROSSES-BOISSEAU AVERTISSEMENT : éteindre et débrancher l’outil avant d’effectuer tout réglage ou d’enlever ou installer tout acces- soire. Pour s’assurer que l’outil est hors tension et avant de le reb ...

  • Epson D28144R - page 34

    Français 33 ASSEMBLAGE DU CAPOT PROTECTEUR FERMÉ (TYPE 1) AVERTISSEMENT : éteindre et débrancher l’outil avant d’effectuer tout réglage ou d’enlever ou installer tout acces- soire. Pour s’assurer que l’outil est hors tension et avant de le rebrancher, mettre l’interrupteur sous et hors tension comme décrit précédemment. 1. Déga ...

  • Epson D28144R - page 35

    Français 34 1 . Laisser l’outil atteindre son plein régime avant de toucher la surface de la pièce avec l’outil. 2. Appliquer un minimum de pression sur la surface de la pièce et laisser l’outil fonc- tionner à haute vitesse. La coupe est à son meilleur à vitesse élevée. 3. Une fois le tronçonnage amorcé et le tail- lage de la prem ...

  • Epson D28144R - page 36

    Français 35 légaux particuliers à l’acheteur, mais celui-ci pourrait aussi bénéfi- cier d’autres droits variant d’un état ou d’une province à l’autre. En plus de la présente garantie, les outils D E WALT sont couverts par notre : CONTRAT D’ENTRETIEN GRATUIT D’UN AN D E WALT entretiendra l’outil et remplacera les pièces usé ...

  • Epson D28144R - page 37

    Español 36 Instrucciones de seguridad generales ¡ADVERTENCIA! Lea todas las instrucciones hasta comprenderlas. No ajustarse a las instruc- ciones siguientes puede ser causa de choque eléctrico, incendio o lesiones graves. CONSERVE ESTAS INSTRUCCIONES ÁREA DE TRABAJO • Mantenga el área de trabajo limpia y bien iluminada. Las bancadas desorden ...

  • Epson D28144R - page 38

    Español 37 Calibre mínimo para cordones de extensión Volts Longitud total del cordón en metros 120V 0-7,6 7,6-15,2 15,2-30,4 30,4-45,7 240V 0-15,2 15,2-30,4 30,4-60,9 60,9-91,4 Amperaje Más No más Calibre del cordón AWG de de 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 No recomendado SEGURIDAD PERSONAL • Al utili ...

  • Epson D28144R - page 39

    Español 38 herramienta está dañada, hágala reparar antes de usarla. Muchos accidentes los provocan unas herramientas mal cuidadas. • Utilice únicamente los accesorios recomendados por el fabricante para su modelo. Un mismo accesorio puede ser adecuado para una herramienta, pero peligroso si se usa en otra. SERVICIO • El servicio a la herra ...

  • Epson D28144R - page 40

    Español 39 • Evite darle botes al disco o maltratarlo. Si esto sucede, detenga la herramienta e inspeccione el disco para detectar grietas o defectos. • Dirija las chispas lejos del operador, los espectadores o los materiales inflamables. Se pueden producir chispas mientras se corta o se esmerila. Las chispas pueden provocar quemaduras o inici ...

  • Epson D28144R - page 41

    Español 40 (NIOSH y OSHA respectivamente, por sus siglas en inglés). Aleje la cara y el cuerpo del contacto con las partículas. PRECAUCIÓN: Tenga mucho cuidado al trabajar en un ángulo, ya que puede producirse un movimiento repentino y violento de la esmeriladora si el disco u otro accesorio entra en contacto con una segunda superficie o el bo ...

  • Epson D28144R - page 42

    Español 41 apagará. El interruptor debe pasar un ciclo (apagarse y encend- erse) para reiniciar la herramienta. La energía volverá al nivel normal un a vez que la herramienta se haya enfriado y tenga una temperat ura de funcionamiento adecuada. NOTA: Haga funcionar la herramienta sin carga para reducir el tiempo de inactividad porque la unidad ...

  • Epson D28144R - page 43

    Español 42 ENSAMBLADO Y AJUSTES CONEXIÓN DEL MANGO LATERAL El mango lateral (E) se puede colocar en cualquiera de los lados de la caja de engranajes, en los agujeros roscados, según se muestra. Antes de utilizar la herramienta, verifique que el mango esté bien ajustado. Utilice una llave para ajustar firmemente la agarradera lateral. Rotación ...

  • Epson D28144R - page 44

    Español 43 se requieren protectores diferentes para los accesorios, que no están incluidos con la herramienta. Las instrucciones para el mon- taje de esos protectores de accesorios se incluyen en el envase del accesorio. M O N 1. Abra el cerrojo del protector (M). Alinee las lengüetas (N) del pro- tector con las ranuras (O) de la caja de engrana ...

  • Epson D28144R - page 45

    Español 44 Discos de corte de 114,3 mm (4-1/2") y 127 mm (5") Protector Tipo 1 Brida de respaldo de cambio rápido Disco de corte abrasivo Tipo 1 Tuerca de fijación roscada Protector Tipo 1 Brida de respaldo de cambio rápido Disco de corte de diamante Tuerca de fijación roscada Discos de corte de 152,4 mm (6") Discos de alambre C ...

  • Epson D28144R - page 46

    Español 45 esmeriladora con un protector flojo o con la palanca de la abrazadera en la posición de abierta. 5. Para retirar el protector, abra el cerrojo del protector, gire el protector para que las flechas se alineen y tire del mismo. NOTA: El protector está ajustado en fábrica P para el diámetro del cubo de la caja de engranajes. Si, despu? ...

  • Epson D28144R - page 47

    Español 46 la superficie antes de apagarla. Permita que la herramienta deje de girar antes de depositarla sobre una superficie. FUNCIÓN DE ARRANQUE SUAVE La función de arranque suave permite adquirir velocidad lentamente para evitar una sacudida inicial en el arranque. Esta característica es especialmente útil cuando se trabaja en lugares estr ...

  • Epson D28144R - page 48

    Español 47 únicamente cuando la herramienta esté apagada, desenchu- fada de la fuente de energía y se haya detenido por completo. No active el bloqueo del eje mientras la herramienta esté fun- cionando porque producirá daños a la misma. Para activar el bloqueo, oprima el botón de bloqueo del eje y gire el eje hasta que no lo pueda girar má ...

  • Epson D28144R - page 49

    Español 48 4. Mientras oprime el botón de bloqueo del eje, ajuste la tuerca de fijación con una llave. 5. Para retirar el disco, oprima el botón de bloqueo del eje y afloje la tuerca de fijación roscada con una llave. NOTA: Si el disco gira después de ajustada la tuerca de fijación, verifique la orientación de la tuerca de fijación roscada ...

  • Epson D28144R - page 50

    Español 49 velocidad de lijado es mayor cuando la herramienta opera a alta velocidad. 3. Mantenga un ángulo de 5° a 10° 5˚-10˚ entre la herramienta y la superficie de trabajo. 4. Mueva la herramienta continua- mente hacia adelante y hacia atrás para evitar la creación de estrías en la superficie de trabajo. 5. Retire la herramienta de la s ...

  • Epson D28144R - page 51

    Español 50 marcar círculos en la superficie de trabajo. Apoyar la herra- mienta sobre la superficie de trabajo, sin moverla, o mover la herramienta en círculos provoca quemaduras y marcas circu- lares sobre la superficie. 5. Retire la herramienta de la superficie de trabajo antes de apagarla. Permita que la herramienta deje de girar antes de dep ...

  • Epson D28144R - page 52

    Español 51 Montaje y uso de discos de corte (Tipo 1) Los discos de corte incluyen los discos de diamante y los discos abrasivos. Se dispone de discos de corte abrasivos para utilizar en metal y concreto. También se pueden usar discos de diamante para cortar concreto. NOTA: Todas las esmeriladoras que usan discos Tipo 1 emplean la brida de respald ...

  • Epson D28144R - page 53

    Español 52 3. Instale la tuerca de fijación roscada con la sección elevada (piloto) en dirección opuesta al disco. 4. Oprima el botón de bloqueo del eje y ajuste la tuerca de fijación con una llave. 5. Para retirar el disco, tómelo y gírelo mientras oprime el botón de bloqueo del eje. USO DE RUEDAS DE CORTE ADVERTENCIA: No utilice discos d ...

  • Epson D28144R - page 54

    Español 53 53 MERIDA, YUC Calle 63 #459-A - Col. Centro (999) 928 5038 MONTERREY, N.L. Av. Francisco I. Madero No.831 - Col. Centro (81) 8375 2313 PUEBLA, PUE 17 Norte #205 - Col. Centro (222) 246 3714 QUERETARO, QRO Av. Madero 139 Pte. - Col. Centro (442) 214 1660 SAN LUIS POTOSI, SLP Av. Universidad 1525 - Col. San Luis (444) 814 2383 TORREON, C ...

  • Epson D28144R - page 55

    Español 54 e informac ión acerca de reparaciones realizadas bajo garantía, visítenos en www.dewalt.com o dirígase al centro de servicio más cercano. Esta garantía no aplica a accesorios o a daños causa- dos por reparaciones realizadas o intentadas por terceros. Esta garantía le otorga derechos legales específicos, además de los cuales pu ...

  • Epson D28144R - page 56

    D E WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (APR07) Form No. 651870-00 D28114, D28114N, D28131, D28140, D28144, D28144N Co pyright © 2006, 2007 D E WALT The following are trademarks for one or more D E WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the h ...

Manufacturer Epson Category Grinder

Documents that we receive from a manufacturer of a Epson D28144R can be divided into several groups. They are, among others:
- Epson technical drawings
- D28144R manuals
- Epson product data sheets
- information booklets
- or energy labels Epson D28144R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Epson D28144R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Epson D28144R, service manual, brief instructions and user manuals Epson D28144R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Epson D28144R.

Similar manuals

A complete manual for the device Epson D28144R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Epson D28144R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Epson D28144R.

A complete Epson manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Epson D28144R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Epson D28144R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Epson D28144R, that we can find in the current document
3. Tips how to use the basic functions of the device Epson D28144R - which should help us in our first steps of using Epson D28144R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Epson D28144R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Epson D28144R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Epson D28144R?

Use the form below

If you did not solve your problem by using a manual Epson D28144R, ask a question using the form below. If a user had a similar problem with Epson D28144R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)