English dropdown-ico

Manual Hitachi BE-IR30

26 pages 0.25 mb
Download

Go to site of 26

Summary
  • Hitachi BE-IR30 - page 1

    Please read this operation Guide carefully for proper operation, and keep it for future refernce. B E-IR30 / 31 Infrared B/W Camera Module Operation Guide ...

  • Hitachi BE-IR30 - page 2

    Table of Contents BE-I R30 / 31 1 1. Intr oduction ･･･････････････････････････････････････････   2 2. General ･･･････････････････････････････････････････････   2 3. C ...

  • Hitachi BE-IR30 - page 3

    1. Introducti on BE-I R30 / 31 2 Thank you v ery much for your purchase of the Hitachi BE-IR30/31 Black and W hite Camera Module. Prior to using this camera , read this manual carefully. 2 . G e n e r a l The BE-IR30/31 is a monochrom e camera module featuring sensitiv ity in the near infrared spectrum using a 1/3- inch size CCD imaging dev ice. Re ...

  • Hitachi BE-IR30 - page 4

    4 ． ． ． ． Specif ications BE-I R30 / 31 3 2) Sensing area EIA : 6.00(H) × 4.96(V)mm CCIR : 6.00( H) × 4.96(V)mm 3) Signal format Conforming to EIA or CCIR. 4) Scanning system 2:1 interlaced 5) Hor. scanning frequency EIA : 15.734 kH z CCIR : 15.625 kHz 6) Vert. scanning frequency EIA : 59.94 Hz CCIR : 50 Hz 7) Sync sy st em BE-IR30 : Inte ...

  • Hitachi BE-IR30 - page 5

    4 ． ． ． ． Specif ications BE-I R30 / 31 4 21) St andard lens f3.8 (BE-IR30B/31B only) Focal distance f 3.8 mm F value 2.0 H 70.9 Picture angle V 52.9 21) Dimensions BE-IR30A/31A: 34 (W ) × 34 (H) × 20 (D) m m BE-IR30B/31B: 34 (W ) × 34 (H) × 32 (D) m m (less lens) BE-IR30C/31C: 34 (W ) × 34 (H) × 24 (D) m m 22) Mass BE-IR30A/31A: Appr ...

  • Hitachi BE-IR30 - page 6

    5. Notes to users BE-I R30 / 31 5  Power supply z Connect a 9V DC volt age (8. 5 t o 9. 5V) from an external regulat ed DC pow er supply . z Use a stable power supply w it hout ripple and noise. z Prior to turning on the power swit ch , check that the polarities of the power cable are correct , referring to the connection diagram (Page 11 , 12) ...

  • Hitachi BE-IR30 - page 7

    5. Notes to users BE-I R30 / 31 6  Phenomena inherent to CCD imaging dev ice Following are phenomena inherent t o a CCD imaging dev ice , and not defect s . z Smear and blooming W hen strong light (lamp , fluorescent lamp , refl ected light , etc.) is shot , pale bands are displayed v ert ically above and below the light. In this case , change t ...

  • Hitachi BE-IR30 - page 8

    6. External view BE-I R30 / 31 7 BE-IR30B/31B ...

  • Hitachi BE-IR30 - page 9

    6. External view BE-I R30 / 31 8 BE-IR30C/31C ...

  • Hitachi BE-IR30 - page 10

    6. External view BE-I R30 / 31 9 Lens 19.2 ± 0.5 (C-mount) 1.4 ± 0.2 CCD Base plate Imaging face Lens-mount Extension of optical path due to the thicknes s of CCD glas s is considered. BE-IR30A/31A 7. Optical dimensions ...

  • Hitachi BE-IR30 - page 11

    8. Installation BE-I R30 / 31 10 W hen installing the camera in a housing or unit of equipment, secure with t wo M2 screws inserted into the 2. 5 mm diameters holes of the SENS board base plate. 1. Use the SENS board holds to install the camera. Avoid using only the Main board, due to risk of damage to the board connector. 2. Avoid unnecessary stre ...

  • Hitachi BE-IR30 - page 12

    9. Typical connection BE-I R30 / 31 11 BE-IR30 Image processor or Video monitor Regulated power supply (More then 300 mA) Note1 : • When more than one video monitor is connected in series , set the 75 Ω termination sw itch on the last unit to ON. Note2 : • Supply voltage range : 8.5 to 9.5V • Be sure to check the polarities of the pow er so ...

  • Hitachi BE-IR30 - page 13

    9. Typical connection BE-I R30 / 31 12 BE-IR31 Image processor or Video monitor Regulated power supply (More then 300 mA) Note1 : • When more than one video monitor is connected in series , set the 75 Ω termination sw itch on the last unit to ON. Note2 : • Supply voltage range : 8.5 to 9.5V • Be sure to check the polarities of the pow er so ...

  • Hitachi BE-IR30 - page 14

    10. External sync (BE-IR31) BE-I R30 / 31 13 Supply sync signals (HD and VD) for BE-IR31 operation. Refer to connection on page 12. z Horizontal and vertical drive signal inputs HD EIA: f(H) = 15.734 kHz ± 1 % VD EIA: f(V) = 59.94 Hz (f(V) = f( H) ÷ 262.5) z Input level HD 4 to 6 Vp-p negative VD 4 to 6 Vp-p negative z Input im pedance 1 k Ω HD ...

  • Hitachi BE-IR30 - page 15

    11. Function setting and changes BE-I R30 / 31 14 W hen changing the function settings , perform the w ork with thorough care. Be sure to use anti-static measures such as a grounding band. Also observ e safety precautions when soldering to avoid burn and fire hazards. Hitachi Denshi assumes on liability for damage or injury result ing fr om such w ...

  • Hitachi BE-IR30 - page 16

    11. Function setting and changes BE-I R30 / 31 15 11-2 Gamma response The factory setting is gamma on. If necessary , the gamma response can be changed as follows. Change the gamma response by changing the chip part. Gamma ( γ )response R217 R218 R219 ON Absent 0 Ω 0 Ω Factory sett ing OFF 0 Ω Remove Remove 0 Ω : Part code RME1784 Descript ...

  • Hitachi BE-IR30 - page 17

    11. Function setting and changes BE-I R30 / 31 16 11-3 Auto electronic shutter on / off Factory sett ing for auto elect ronic shut t er is off. If necessary , it can be set to on. Absent the R259 , R260 chip t o set t he aut o elect r onic shut t er to on. Auto electronic s hutter R259 R260 OFF 0 Ω 0 Ω Factory setting ON Absent Absent 0 Ω : P ...

  • Hitachi BE-IR30 - page 18

    11. Function setting and changes BE-I R30 / 31 17 11-4 Changes to fixed shutter mode The fixed shutter mode can be changed by replacing the chip parts indicat ed below . Mode R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R269 Normal mode 0 Ω 0 Ω Absent 0 Ω A bsent 6800 10k 27k 10k 10k 27k Auto elec t ronic shutt er m ode Remove Rem ove Ab ...

  • Hitachi BE-IR30 - page 19

    11. Function setting and changes BE-I R30 / 31 18 11-5 BE-IR30 external sync The BE-IR30 factory sett ing is for internal sync. If required, this can be changed to external sync by changing chip part s. Change the following chip parts for external sync operat ion. Sy nc system R280 R281 R282 R284 Internal 100 Ω Absent Absent 0 Ω Factory setti n ...

  • Hitachi BE-IR30 - page 20

    11. Function setting and changes BE-I R30 / 31 19 11-6 BE-IR31 internal sync The BE-IR31 factory sett ing is for external sync. If required, this can be changed to internal sync by changing chip part s. Change the following chip parts for internal sy nc operat ion. Sy nc system R280 R281 R282 R284 External Absent 0 Ω 100 Ω Absent Factory settin ...

  • Hitachi BE-IR30 - page 21

    11. Function setting and changes BE-I R30 / 31 20 11-7 HD and VD output (BE-IR30 only) The BE-IR30 can be provided with horizontal and vert ical drive outputs by changing chip parts. Change the following chip parts to prov ide HD and VD outputs. R233 R239 R240 R241 R242 R248 R249 R250 Factory sett ing 0 Ω Absent 0 Ω Absent 0 Ω Absent 0 Ω Ab ...

  • Hitachi BE-IR30 - page 22

    12. Opt ions BE-I R30 / 31 21 LA-IR20 Mount adapter dimensions Remove c-mount attachment to use as cs-mount. ...

  • Hitachi BE-IR30 - page 23

    12. Options BE-I R30 / 31 22 BE-IR30A/31A and LA-IR 20 combined dimensions ...

  • Hitachi BE-IR30 - page 24

    12. Options BE-I R30 / 31 23 BE-IR30C/31C and CS mount adapter (opti on) combined dimensions ...

  • Hitachi BE-IR30 - page 25

    BE-I R30 / 31 24 Spectral sensitivity (t ypical example) 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 400 500 600 700 800 900 1000 Relative sensitivity W avelength( nm) ...

  • Hitachi BE-IR30 - page 26

    BE-I R30 / 31 25 Caution The s pecifications of this equipm ent are subj ect to change without notice for im provem ent. Prior to placing your order , be sur e to confirm that these spec ifications are the latest ones. Hitachi Denshi guarantee that the equipment s hipped from our factor y conf orm s to the Hitachi Denshi’s st andard warranty cond ...

Manufacturer Hitachi Category Camera Accessories

Documents that we receive from a manufacturer of a Hitachi BE-IR30 can be divided into several groups. They are, among others:
- Hitachi technical drawings
- BE-IR30 manuals
- Hitachi product data sheets
- information booklets
- or energy labels Hitachi BE-IR30
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hitachi BE-IR30.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hitachi BE-IR30, service manual, brief instructions and user manuals Hitachi BE-IR30. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hitachi BE-IR30.

Similar manuals

A complete manual for the device Hitachi BE-IR30, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hitachi BE-IR30 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hitachi BE-IR30.

A complete Hitachi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hitachi BE-IR30 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hitachi BE-IR30, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hitachi BE-IR30, that we can find in the current document
3. Tips how to use the basic functions of the device Hitachi BE-IR30 - which should help us in our first steps of using Hitachi BE-IR30
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hitachi BE-IR30
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hitachi BE-IR30 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hitachi BE-IR30?

Use the form below

If you did not solve your problem by using a manual Hitachi BE-IR30, ask a question using the form below. If a user had a similar problem with Hitachi BE-IR30 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)