Manual Fujitsu RX100 S2

275 pages 11.27 mb
Download

Go to site of 275

Summary
  • Fujitsu RX100 S2 - page 1

    1 PRIMERGY RX100 S2 Use r’s Guide Ar eas Co v er ed Before Reading This Manual This section explains the notes for your safety and conventions used in this manual. Make sure to read this section. Chapter 1 Overview This chapter explains component name s and basic operations of this server , as well as an overview of the software provided with thi ...

  • Fujitsu RX100 S2 - page 2

    2 Bef or e R eading T his Manual ■ T rademarks VGA and PS/2 are registered trademarks of IB M Corporation. Intel, Pentium, and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the USA and other countries. Microsoft, Windows, Windows NT , and Windows Serv er are trademarks or reg istered trademarks of Mic ...

  • Fujitsu RX100 S2 - page 3

    3 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 8 9 Remarks ■ W arning De scriptions V arious symbols are use d throughout thi s manual. These are used to emphasize imp ortant points fo r your safety and that of othe rs. The following are the symbols and their meani ngs: The following sy mbols are used to indic ate the ty pe of warning or cauti ...

  • Fujitsu RX100 S2 - page 4

    4 ■ Screen Sh ots and Figu res Screen shots and figures are used as visual aids throughout this manual . Wi ndows, screens, and file names may vary depending on the OS, software, or configu ration of the server u sed. Figures in this manual may not show cables that are actually c onnected for convenie nce of explanation. ■ Consecuti ve Operatio ...

  • Fujitsu RX100 S2 - page 5

    5 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 8 9 Reference Information ■ Software Manuals Software Manual contains othe r reference information and caut ions for ServerStart not de scribed in this manual. Please read it before using Serve rStart. Software Manual is c ontained as a "README.T XT" file in the root directory on the Ser ...

  • Fujitsu RX100 S2 - page 6

    6 ...

  • Fujitsu RX100 S2 - page 7

    7 PRIMERGY RX100 S2 Use r’s Guide Contents Chapter 1 Ove rv iew 1. 1 RX100 S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 1.2 Su ppl ied Soft ware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.2.1 Setup Su pport T ool - Server S tar t . . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 8

    8 Cha pt er 3 OS Installation Using ServerStart 3.1 Guid ed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 3.1.1 S tarting Up the Guided Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 3.1.2 Open/c reate a Configurat ion File . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 9

    9 PRIMERGY RX100 S2 Use r’s Guide 4.3 Instal ling the LAN Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 4.3.1 Inst alling the LAN Dr iver (Windows Server 2003) . . . . . . . . . . . . . . . . . . 120 4.3.2 Inst alling the LAN Dr iver (Windows 2000 Server) . . . . . . . . . . . . . . . . . . 123 4.3.3 La test Drivers . . . ...

  • Fujitsu RX100 S2 - page 10

    10 Cha pt er 7 Installing Internal Options 7.1 Before Installing Internal O ptio ns . . . . . . . . . . . . . . . . . . . . . . 162 7.2 Removing and Attach ing the T o p Cove r . . . . . . . . . . . . . . . . . . 164 7.2.1 Removing and Attachi ng the T op Cover . . . . . . . . . . . . . . . . . . . . . . . . . 164 7.3 Installing Me mory Modules . . ...

  • Fujitsu RX100 S2 - page 11

    11 PRIMERGY RX100 S2 Use r’s Guide 8.2.15 Console Re direction Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 8.2.16 Ex it Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 16 Cha pte r 9 Operation and Maintenance 9.1 Da ily Main ten ance . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 12

    12 B.4 Pow er Cord Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 C Remote Control Function and Console Redirec tion . . . . . . . . 265 C.1 Key Operation s for Consol e Redirecti on . . . . . . . . . . . . . . . . . . . . . . . . . 265 C.2 Connecting t he Server to a PC . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 13

    13 Chapter 1 Ov er view This chapter explains an overview of the system hardware and software. In addition, the workflow , from placing the server to starting the operation, is also described. 1.1 RX100 S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.2 Supplied Sof tware . . . . . . . . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 14

    14 Chapter 1 Overview 1 .1 RX100 S2 This serve r has the follo wing features . ■ High Rel iability ● Disk Array System Configu ration A disk array system (RAID 0/1) can be co nfigured using an optional RAID card. ● Hardware and Soft ware Designed for Data Securi ty The locks on the rack and security (password) setting in t he BIOS Setup Utili ...

  • Fujitsu RX100 S2 - page 15

    15 PRIMERGY RX100 S2 User ’s Guide 1 Overview ● Maximum Memory Size of 4GB In addition to t he preinstalled 256MB memory , the system supports up t o 4GB memory . ● Maximum Hard Disk Size o f 293.6GB Up to two internal hard disk units can be insta lled in the 3.5-inch storage bay s. The hard disk size can be increased up to 293.6GB. ● Inter ...

  • Fujitsu RX100 S2 - page 16

    16 Chapter 1 Overview 1 .2 Supplied Software ServerS tart for supporting setup and high reliability tools for avoiding problems during server opera tion are suppl ied with thi s server . 1.2.1 Setup Support T ool - ServerStart ServerStart is a setup support tool that helps to install PRIMERGY . It offers easy server installation and proper instal l ...

  • Fujitsu RX100 S2 - page 17

    17 PRIMERGY RX100 S2 User ’s Guide 1 Overview ● Configur ation File (Se rStartBatch .ini) A configuration file stores the serv er setup and client information configu red in ServerStart. T o create a configuration file, use the ServerStart floppy disk supplied with this server . Store only one file on eac h floppy disk. Do not set the ServerS t ...

  • Fujitsu RX100 S2 - page 18

    18 Chapter 1 Overview ● T oolbar In Guided Mode / E xpert Mode  While the wizard is running, do not click the icons on the tool bar to move to the previous or next window. T o move to a different window , click the [Previous ], [Up], or [Next] button at the bottom of the wizard window. ● Wizard Win dow Clicking a wiza rd displays a wiz ard w ...

  • Fujitsu RX100 S2 - page 19

    19 PRIMERGY RX100 S2 User ’s Guide 1 Overview ■ Automatic D river Installatio n Recommended drivers for automaticall y recognized expansion ca rds are installed with the server . This prevents possible mistakes in driver instal lation, such as installation of an olde r version or drivers which were not supplied wi th this server . ■ Automatic ...

  • Fujitsu RX100 S2 - page 20

    20 Chapter 1 Overview ■ System Dia gnosis Support T o ols The system diagnosis support tool is for supporting sy stem diagnosis during normal operation or in the event of trouble. ● Solving Problem s Early [DSNAP] DSNAP is a command line util ity that c ollects all the fa ilure investigation i nformation. System file configuration informati on, ...

  • Fujitsu RX100 S2 - page 21

    21 PRIMERGY RX100 S2 User ’s Guide 1 Overview 1.2.3 Installing High Reliability T ools Y ou can install all high re liability t ools provided with PRIMERGY by specifying them in "Application Wizard" when t he OS is instal led with ServerStar t. The following high reliabili ty tools are installed. A: Installed in any case S: Installed if ...

  • Fujitsu RX100 S2 - page 22

    22 Chapter 1 Overview 1 .3 Component Names and Functions This secti on explains the component name s and functions of the server . 1.3.1 Server (Front V iew) a Internal CD-RO M drive unit (option al) Reads data or programs from a CD-ROM. b Floppy d isk drive unit W rites/reads data to /from a floppy disk. c 3.5-inch stora ge bay Contains an interna ...

  • Fujitsu RX100 S2 - page 23

    23 PRIMERGY RX100 S2 User ’s Guide 1 Overview i System ident ification LED ( ) This LED is used for maintenance. When pressing this button, the front and rear system identification L EDs are lit blue so that the locations of devices being mainta ined can be determined. Also, the [Syste m Identification LED Display ] button of ServerV iew can be u ...

  • Fujitsu RX100 S2 - page 24

    24 Chapter 1 Overview f LAN connec tor A ( ) An Unshielded T wisted Pair (UTP) cable is plugged in. For 1000Mbps connection, a cable conforming to category 5 enhanced is required. As LAN connector A uses the Communication Strea ming Architecture (CSA) port, its data transfer speed may be higher tha n that of LAN connector B. The meanings of the two ...

  • Fujitsu RX100 S2 - page 25

    25 PRIMERGY RX100 S2 User ’s Guide 1 Overview 1.3.3 Server (Internal) a System fan Contact an of fice listed i n the "Contact Information " of "Start Guide " for the system fa n replacement. b PCI slots Expansion cards with t he PCI bus interface c an be installed i n the PCI slots. c CPU One fan is installed by defau lt on th ...

  • Fujitsu RX100 S2 - page 26

    26 Chapter 1 Overview 1.3.4 Baseboard a Memory slot s b Power cont rol connecto r The power unit ca ble is plugged in. c A TX power connector The power unit ca ble is plugged in. d A TX12V po wer connector The A TX12V power unit conne ctor cable is plugge d in. e Fan 6/7 connec tor The system fan 6/7 cable is plugged in. f Fan 3/4 connec tor The sy ...

  • Fujitsu RX100 S2 - page 27

    27 PRIMERGY RX100 S2 User ’s Guide 1 Overview l Floppy d isk drive conne ctor m Power conne ctor for CD- ROM drive The power cable for the optional CD-ROM drive is plugge d in. n JP3 (Fixed) o JP4 (Fixed) p Card locking frame conn ector An expansion card lo cking frame is installed. q JP1 Used to clear the CMOS storage data. For more details, ref ...

  • Fujitsu RX100 S2 - page 28

    28 Chapter 1 Overview 1 .4 Standar d Oper a tions This sect ion explai ns sta ndard server operations, including ho w to turn th e server on/ off and to insert/ eject a floppy disk. 1.4.1 Opening the Rack Door This section expla ins how to open the front and rear doors of the 40U standard rack. Refer to the manual included with the rack for procedu ...

  • Fujitsu RX100 S2 - page 29

    29 PRIMERGY RX100 S2 User ’s Guide 1 Overview 2 T urn th e handle in th e direction of the arrow an d pull it forwar d. ■ Opening the Rear Door 1 T urn the rack key and pull the rac k handle up. T urn and then pull ...

  • Fujitsu RX100 S2 - page 30

    30 Chapter 1 Overview 2 T urn the handl e in the direct ion of the arrow and pull it for ward.  Unless you are inserting/removing media or turning the pow er on/off, keep the rack door closed. Doing so blocks electric waves from cell phones, etc.  Do not lose the keys. If the key is lost, contact an office listed in the "Contac t Informa ...

  • Fujitsu RX100 S2 - page 31

    31 PRIMERGY RX100 S2 User ’s Guide 1 Overview 3 Press the pow er switch of the monitor and pe ripheral devi ces. 4 Press the pow er switch on t he front of the se rver . The server's power L ED is lit green. When the power is turned on, the se rver Power On Self T est (POST). If any abnormalitie s are detected by POST , error messages are di ...

  • Fujitsu RX100 S2 - page 32

    32 Chapter 1 Overview 3 Press the pow er switch on t he front of the se rver . The server's power LED is lit amber . 4 T urn of f the display an d peripheral de vices.  The time to turn off the server can be set with the ASR setting (on the [Power On/O ff] t ab) using ServerView supplied with this server . For details, refer to "3.2 Se ...

  • Fujitsu RX100 S2 - page 33

    33 PRIMERGY RX100 S2 User ’s Guide 1 Overview 1.4.4 Inserting and Ej ecting a Floppy Disk ■ Cautions When using a floppy disk, note the foll owing points. • Do not expose th e disk to any fluids. • Do not open the shutter of the floppy disk and touch the disk surface. • Do not bend the floppy disk or plac e heavy objects on it. • Do not ...

  • Fujitsu RX100 S2 - page 34

    34 Chapter 1 Overview 1.4.5 Inserting and Ejecting a CD-ROM CD-ROM drive is available as an option for this server . ■ Cautions for Hand ling CD-ROM Drive • Use the d rive in a dry place with low airb orne dust le vels. Entry of wat er , a paper clip , or other liqu ids or metal objects can cause elec tric shock or failures. • Do not use the ...

  • Fujitsu RX100 S2 - page 35

    35 PRIMERGY RX100 S2 User ’s Guide 1 Overview ■ Inserting th e CD -ROM 1 Make sure the server is turned on an d press the CD-ROM eject bu tton. The CD- ROM tray com es out a lit tle. 2 Pull the C D-ROM tray out. 3 Place the C D-ROM at the cent er of the tray . While supporting the CD-ROM tray , push the tray until it cli cks into position.  ...

  • Fujitsu RX100 S2 - page 36

    36 Chapter 1 Overview ■ Ejecting the CD -ROM T o eject the CD-ROM, press the CD-ROM eject button (EJECT) in the same way as steps 1 to 2 in " ■ Inserting the CD-ROM" (  pg.35). ...

  • Fujitsu RX100 S2 - page 37

    37 PRIMERGY RX100 S2 User ’s Guide 1 Overview 1.5 W o r kf l o w Use the follo wing workflow fr om server in stallation to start of ope ration. Installing the server Referring to "Safety Precautions" and "Start Guide", install the server to a suitable place. Preparing the server - Install Internal options - Set hardware Referr ...

  • Fujitsu RX100 S2 - page 38

    38 Chapter 1 Overview ...

  • Fujitsu RX100 S2 - page 39

    39 Chapter 2 Chec king bef or e OS Installa tion This chapter explains the preparation on the server and cautions necessary before OS installation. Please read this chapter before starting inst allation. 2.1 Prep aration on the Server . . . . . . . . . . . . . . . . . . . . . . . . 40 2.2 Selecting the I nstalla tion Method . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 40

    40 Chapter 2 Che cking bef ore OS Inst allation 2 .1 Pr epar a tion on the Ser v er Before st arting i nstall ation, inst all i nternal opti ons to the server and perform necessary hardware setting s. 2.1.1 Installing Internal Options Internal options are classifie d into those that must be installed before the OS installati on and those that must ...

  • Fujitsu RX100 S2 - page 41

    41 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Checking before OS Installation 2.1.2 Hardware Settings Before starting installat ion, set up necessary hardware conf igurations using the BIOS Setup Utility . ■ BIOS Setup Utili ty The BIOS Setup Utility must be set in the followi ng cases. For details on how to set the BIOS Setup Utility , ...

  • Fujitsu RX100 S2 - page 42

    42 Chapter 2 Che cking bef ore OS Inst allation 3 Exit the BIOS Setup Utility an d turn off the serve r .  Y ou can turn the powe r on from a client (via a LAN) by utilizing the W akeup on LAN (WOL) function. Refer to "5.5.5 Turning the Power On via a LAN" (  pg.148).  Be sure to install ServerVi ew to control the powe r supply v ...

  • Fujitsu RX100 S2 - page 43

    43 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Checking before OS Installation 2 .2 Selecting the Installation Method When installing the OS for the first time, the re are multiple installation methods. Refer to the follo wing to decide on the meth od.  T o set up multiple servers with the same model and configuration, refer to "3.5 ...

  • Fujitsu RX100 S2 - page 44

    44 Chapter 2 Che cking bef ore OS Inst allation 2 .3 Pr ecautions on Installa tion Read the f ollowing notes before starting OS in stallation. 2.3.1 Installation P artition Size For installation using ServerStart, the installation pa rtition size can be set as follows, dependi ng on the OS to be installed and format. ● Notes • When you want to ...

  • Fujitsu RX100 S2 - page 45

    45 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Checking before OS Installation ■ Checking befo re OS Installati on • When removing the hard disk unit If you configure the RAID with Server Start, use the Backg round Initiali zation funct ion for the arra ys. Before removing the har d disk unit, make sure that t he disk has already been i ...

  • Fujitsu RX100 S2 - page 46

    46 Chapter 2 Che cking bef ore OS Inst allation ■ License for Use of System for Se rverStart "License for Use of System for ServerS tart" linked from the ServerStart startu p window is a license fo r use of W indows PE contained in the ServerS tart CD-ROM. W indows PE for starting up ServerStart ca n be only used for installing W indows ...

  • Fujitsu RX100 S2 - page 47

    47 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Checking before OS Installation 2.3.6 Cautions for Manual Installation ■ Notes on Using a RAID Card In addition to t he completion of RAID card configuration, the hard disk under the RAID c ard must be initialized before the OS is installed. T o check the RAID card configuration, start up W e ...

  • Fujitsu RX100 S2 - page 48

    48 Chapter 2 Che cking bef ore OS Inst allation 2 . 4 Pr eparation f or Using Ser v erStar t on a Client Computer When using t he preconfigu ration mode for setting ins talla tion informa tion in advanc e or when creat ing a driver d isk using th e FloppyBuild er function, instal l ServerS tart on the clien t computer . ● System Requireme nts for ...

  • Fujitsu RX100 S2 - page 49

    49 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Checking before OS Installation 3 Click [Next]. The [License Agre ement] window appears. 4 Select [I accept the li cense agreement ] and click [N ext]. The [User Information] window a ppears. 5 Enter the user informat ion of the software and click [Next]. The [Installation Folder] window appear ...

  • Fujitsu RX100 S2 - page 50

    50 Chapter 2 Che cking bef ore OS Inst allation 8 S pecify whether or not t o copy the content s of the CD. When you selec t [Y es] for "enable the use of ServerS tart without CD. ", you can sta rt the preconfiguration mode on the clien t computer without using the CD-ROM. If you selec t [Y es], specify the tar get folder . The tar get fo ...

  • Fujitsu RX100 S2 - page 51

    51 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Checking before OS Installation 2.4.2 Uninstalling ServerStart Perform the following procedure to uninstall ServerStart from the client computer . 1 Click [S ta rt] → [Settings] → [C ontrol Panel]. 2 Double-cl ick [Add or Remove A pplicati ons] ([Add or Remove Pr ograms] on some operati ng ...

  • Fujitsu RX100 S2 - page 52

    52 Chapter 2 Che cking bef ore OS Inst allation ...

  • Fujitsu RX100 S2 - page 53

    53 Chapter 3 OS Installa tion Using Ser v erStar t This chapter exp lains how to install the OS in the server using ServerS t art. 3.1 Guided mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 3.2 Preconfig uration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 71 3.3 E xpert Mode . . . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 54

    54 Chapter 3 OS Installation Using Ser verS tart 3 .1 Guided mode In guided mode , follow the wizard to specify ha rdware configuratio n and the OS to be installed, save the inform ation necessary for installation in a configura tion file, and install the OS. 3.1.1 Starting Up the Guided Mode Start up the guided mode. 1 T urn on the serv er and ins ...

  • Fujitsu RX100 S2 - page 55

    55 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart The network setting window for remote installa tion appears. 3 Click [OK]. The [Initializa tion of ServerS tart core running] window appe ars and unattended i nstallation will be started. Depen ding on the hardware c onfiguration, this proce ss may take a f ew ...

  • Fujitsu RX100 S2 - page 56

    56 Chapter 3 OS Installation Using Ser verS tart 4 Click [B uild a Serve rS t art Floppy Dis k]. Creation of a Serve rStart floppy disk starts. When t he creation is comple ted, the "Floppy disk has been created." message appea rs. 5 Click [OK]. "Please Select your key board" window appears. 6 Select your k eyboard language f ro ...

  • Fujitsu RX100 S2 - page 57

    57 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 10 Click [Prepare & init iate an unatte nded installation of (OS)]. The guided mode for the selected OS starts up. Start up the wiza rds to s et items in the followin g proced ures. Exiting the wiza rd returns the display to the guided mode window . Open/c ...

  • Fujitsu RX100 S2 - page 58

    58 Chapter 3 OS Installation Using Ser verS tart 3.1.2 Open/create a Configuration File Open a configurati on file. Or create a new file. 1 Click [S tart here to create a comple te configuration file ]. The [Open ServerS tart Configuration File] window appears.  Once a config uration file is op ened, another fi le cannot be open ed until you cli ...

  • Fujitsu RX100 S2 - page 59

    59 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3.1.3 RAID Wizard Configure RAID. In the guided mode, the RAID wizard is display ed only when a RAID card is instal led.  When changing the RAID card, delete the physical pack beforehand. For details on how to delete a physical pack , refer to "PRIMERG ...

  • Fujitsu RX100 S2 - page 60

    60 Chapter 3 OS Installation Using Ser verS tart 3.1.4 Disk Wizard Create and format hard disk partitions.  The disk wizard starts up with the default settings. Be sure to click [MODIFY] to check the settings. Change them as necessary . 1 Click [D isk Wizard : Hard disk p artitio ning and formatt ing]. The [Disk Overview] window appears.  Whe ...

  • Fujitsu RX100 S2 - page 61

    61 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 2 Add, remove, or modify pa rtitions as necessary .  Partition si ze of the F A T file system Whe n "F A T" is selec ted in [File system] and a value equ al to or more than 40 95MB or "Auto- matic settin g" is specified in [Partition si ...

  • Fujitsu RX100 S2 - page 62

    62 Chapter 3 OS Installation Using Ser verS tart 3.1.5 OS Installation Wizard Set computer information, user information, and t he network protocol. ServerStart can configure multiple network patterns. When configuring a domain cont roller , refer to "Using ServerStart to conf igure the Network".  The setting window differs depending o ...

  • Fujitsu RX100 S2 - page 63

    63 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 Set items an d click [Ne xt]. The [Installation Directory and Ti me Zone] window appears. 4 Set items an d click [Ne xt]. The [User Name] window appea rs. 5 Set items an d click [Ne xt]. The [Display Settings] window appear s. ...

  • Fujitsu RX100 S2 - page 64

    64 Chapter 3 OS Installation Using Ser verS tart 6 Set items an d click [Ne xt]. The [Network Protocol] window appears. ...

  • Fujitsu RX100 S2 - page 65

    65 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 7 Set items an d click [Ne xt]. The [Software Components] window a ppears. ...

  • Fujitsu RX100 S2 - page 66

    66 Chapter 3 OS Installation Using Ser verS tart 8 Set items an d click [Ne xt]. The [Services] window appe ars. 9 Set items a nd click [leave wiz ard]. The OS installation wizard closes. ...

  • Fujitsu RX100 S2 - page 67

    67 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3.1.6 Application Wizard Specify install ation of supplied applications such as high relia bility tools. 1 Click [A pplicati on Wizard: Se lect additi onal sof tware componen ts]. The appl ication wi zard appear s. 2 From the [Inst allab le applicat ions] list ...

  • Fujitsu RX100 S2 - page 68

    68 Chapter 3 OS Installation Using Ser verS tart 3.1.7 Close/save the Configuration File When settings in all wizards are completed , save the configuration file. 1 Click [Close a nd save Config uration File]. The [Save ServerSt art Configuration File] window appears. 2 Click [Save As]. The configuration file is saved.  Y ou can specify any name ...

  • Fujitsu RX100 S2 - page 69

    69 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 2 Click [S ta rt].  Clicking [St art now] delet es all disk contents and start s installat ion. Click [Stop] when you do not perform installation. After 10 seconds, installation start s automatically . • When RAID has been configured, the system restarts. ...

  • Fujitsu RX100 S2 - page 70

    70 Chapter 3 OS Installation Using Ser verS tart The server setup a nd OS installation have been completed. Refer t o "Chap ter 5 Op erations after OS Instal lation" (  pg.125) and perf orm necessary procedu res before starting server operati ons. ...

  • Fujitsu RX100 S2 - page 71

    71 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 .2 Pr econfiguration Mode In preconfi guration mode , set and save the informati on necessary fo r instal lation in a configura tion file on a client comput er (with a CD- ROM drive and 10MB or more of free space). Set the saved co nfiguration file on the se ...

  • Fujitsu RX100 S2 - page 72

    72 Chapter 3 OS Installation Using Ser verS tart 2 Click [Floppy Builder]. The [ServerS tart FloppyBuilde r] window appears. 3 Click [ServerSt art S tatus Diskette]. A message prompting y ou to insert the floppy disk appears. 4 Insert the ServerS tart floppy disk supplied with th e server and click [OK].  Set the ServerS tart floppy disk in the ...

  • Fujitsu RX100 S2 - page 73

    73 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 9 Select the O S to install. The [Preparing Instal lation] window appears. ...

  • Fujitsu RX100 S2 - page 74

    74 Chapter 3 OS Installation Using Ser verS tart 3.2.2 Configure Settings in Wizards Click the wizards to set ite ms in the following procedures. For setti ng procedures, refer to descri ption on guided mode wizards ("3.1.2 Open/cre ate a Configuration File" (  pg.58) to "3. 1.6 Application W izard" (  pg.67)). Exiting a w ...

  • Fujitsu RX100 S2 - page 75

    75 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3.2.3 Close/save the Configuration File When settings in all wizards are completed , save the configuration file. 1 Click [Close an d save Config uration File]. The [Save ServerS tart Configuration File] window appears. 2 Click [Save As]. The [ServerSta rt Ses ...

  • Fujitsu RX100 S2 - page 76

    76 Chapter 3 OS Installation Using Ser verS tart 3.2.4 Starting OS Installation Install the OS to the server using the create d configuration file. During installation, do not use the mouse or key board unless it is necessary for install ation operations. Otherwise, installation may fail. 1 T urn on the serv er and insert th e ServerS tart CD -ROM ...

  • Fujitsu RX100 S2 - page 77

    77 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 Click [S ta rt]. Installation starts. • When RAID has been configured, the system restarts. • If a message prompting you to insert the Service Pack CD-ROM appea rs, insert the CD-ROM and click [OK]. This message does not a ppear when Service Pac k is not ...

  • Fujitsu RX100 S2 - page 78

    78 Chapter 3 OS Installation Using Ser verS tart 3 .3 Exper t Mode In expert m ode, start up Disk Man ager , format the installation partition, and install the OS. Use the expert mode only when y ou want to perform installation while maintai ning the existing partitions . Use the guide d mode for normal installation. 3.3.1 Starting Up the Expert Mo ...

  • Fujitsu RX100 S2 - page 79

    79 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 10 Click [Install MS Wind ow Server 2003 interactively (expertise re quired)]. The expe rt mode st arts. Start up the configu ration tools to set items in the following procedures. Exit ing a tool returns to the display to the expe rt mode window . OS installa ...

  • Fujitsu RX100 S2 - page 80

    80 Chapter 3 OS Installation Using Ser verS tart 3.3.2 Disk Manager Start up Disk Manager and format the installation partition. 1 Click [U se Disk Manage r to parti tion and format your disk drive s]. Disk Manager starts up. 2 Format the OS installation partition. Select the OS inst allation partition and click the [Parti tion] menu → [Forma t]. ...

  • Fujitsu RX100 S2 - page 81

    81 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3.3.3 OS Installation Wizard Set computer information, user information, and the network protocol. ServerStart can configure multiple network patterns. When configuring a domain cont roller , refer to "Using ServerStart to conf igure the Network". ? ...

  • Fujitsu RX100 S2 - page 82

    82 Chapter 3 OS Installation Using Ser verS tart 3.3.4 Application Wizard Specify insta llation of supplied a pplications such as high reliability tools. For details on the application wizard, refer to "3.1.6 Appl ication W izard" (  pg.67). 3.3.5 Starting OS Installation Install the OS to the server .  When the installation p artit ...

  • Fujitsu RX100 S2 - page 83

    83 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 Enter the file name and click [Save As]. Installation starts a utomatically . • If a message prompting you to insert the Service Pack CD-ROM appea rs, insert the CD-ROM and click [OK]. This message does not a ppear when Service Pac k is not selected. • I ...

  • Fujitsu RX100 S2 - page 84

    84 Chapter 3 OS Installation Using Ser verS tart 9 When a message o n instal lation compl etion appears , press any key . 10 Restart the sy stem. Click [Start] → [Shutdown]. Sele ct [Restart] and click [OK]. The system resta rts. 11 When the syst em restar ts, lo g on to the serv er using the A dministrator account for the loca l computer . The s ...

  • Fujitsu RX100 S2 - page 85

    85 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 .4 R emote Installa tion ServerS tart supports remote inst allati on.  Before performing remote installation, be sure to read "Cautions for Remote Installation" in the online help. 3.4.1 Overview of Remote Installation Remote installation is a m ...

  • Fujitsu RX100 S2 - page 86

    86 Chapter 3 OS Installation Using Ser verS tart ● Remote Instal lation Using a PXE Server In remote installation using a PXE server , the network startup (PXE) function of the PXE server starts up the target server and performs installation in preconfigurat ion mode. This method is used when the target serve r does not have a CD-ROM or floppy di ...

  • Fujitsu RX100 S2 - page 87

    87 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3.4.2 System Requirements for Remote Resource/PXE Servers Because remote insta llation is performed via a network, the e nvironment must have at le ast one W indows server and a l ocal area network. In addition, the following environ ment is required. ■ Remo ...

  • Fujitsu RX100 S2 - page 88

    88 Chapter 3 OS Installation Using Ser verS tart ● Checking Server Free Space The following tabl e shows the amount of free space required for e ach installation re source. Calculate the total resource size . Check that the remote resource server / PXE server has enough free space (free space greater than the space required for the resources). Wh ...

  • Fujitsu RX100 S2 - page 89

    89 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 2 Click [Add or Remove Window s Components]. Click t he [Dynamic Host Configurat ion Protocol (DH CP)] service from [Network Servic es]. The DHCP service is i nstalled. 3 Create and con figure a DHCP scope so that th e IP address can be distributed. ■ Instal ...

  • Fujitsu RX100 S2 - page 90

    90 Chapter 3 OS Installation Using Ser verS tart 6 Select the in stallation folder a nd click [Next]. T o change the installation folder , click [Browse] and select the folder . The [Select Features] window appears. Configure [ServerS tart - remote instal lation] so that it will be installed. Clicking [Disk Cost] displays the following widow where ...

  • Fujitsu RX100 S2 - page 91

    91 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 7 Click [Next]. The [contents tree] window appears. 8 Configure t he ServerS tart image neces sary for netwo rk startup (PXE) and click [Next]. The [User account for access to the contents tree] window appears. ...

  • Fujitsu RX100 S2 - page 92

    92 Chapter 3 OS Installation Using Ser verS tart 9 S pecify the user accoun t for the conten t tree and clic k [Next]. The [PXE Server] window appears. 10 Select [ye s] when the PXE server perfor ms the DHCP ser vice or select [n o] when the DHCP and PXE servers are configur ed separately . The n click [Next]. The [PXE Server] window appears. 11 Wh ...

  • Fujitsu RX100 S2 - page 93

    93 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 13 Click [Show Readm e file]. The [Readme] window appea rs. Read the text. When you finish, click [ ] in the upper -right corner of the window to close the [Readme] window . 14 Click [Next]. The im age file i s copied . The image file copyi ng process takes ab ...

  • Fujitsu RX100 S2 - page 94

    94 Chapter 3 OS Installation Using Ser verS tart ● Checking the DHC P Service Perform the following check only when the PXE server performs the DHCP service. 1 On the PXE server , click [S tart] → [Programs] → [Admi nistrativ e T ools] → [DHCP] to start up the DHCP adm inistrative tool. 2 Click [Server Options] and check that th e "060 ...

  • Fujitsu RX100 S2 - page 95

    95 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 Click the [Sec urity] tab, add th e Guest accou nt, and set t he "Read and execute", "Vie w folder conte nts li st", and "Read " access permi ssions. The preparation of the PXE server has be en completed. Then, perform "3.4 ...

  • Fujitsu RX100 S2 - page 96

    96 Chapter 3 OS Installation Using Ser verS tart 3.4.5 Starting Remote Instal lation Using a PXE Server Perform remote installation using a PXE server in the follo wing procedures. ■ Checking the Netwo rk Startup (PXE) Setting Remote installation using a PXE server is performed via th e onboard LAN. Enable the network startup (PXE) of the target ...

  • Fujitsu RX100 S2 - page 97

    97 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 2 Click [Click her e to prepare an o perating sy stem installation for a PRIMERGY Server]. The [Prepare the installat ion of an operating system for PRIMERGY Servers] window appears. 3 Click [C reation of a Se rverS tart Confi guration fi le for the inst allat ...

  • Fujitsu RX100 S2 - page 98

    98 Chapter 3 OS Installation Using Ser verS tart 7 Configure re mote installation. 1. Enter the "MAC address of the target system". 2. Select the "PRIMERGY model type". 3. S pecify the "Configuration file" containing the installation settings. ...

  • Fujitsu RX100 S2 - page 99

    99 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 8 Click [S ta rt Insta llation]. Installation starts. All disk conte nts on the target server are de leted. The [ServerS tart Boot Manager] window a ppears. Check that the status is "W aiting for cli ent". 9 T urn on the t arget server . It is starte ...

  • Fujitsu RX100 S2 - page 100

    100 Chapter 3 OS Installation Using Ser verS tart 3.4.6 Starting Remote Inst allation Using a Remote Resource Server In remote install ation using a remote resource server , installation is perfor med using shared resource s on the remote resource server . Perform "3.4.4 Preparati on of Remote Resources" (  pg. 95) before starting inst ...

  • Fujitsu RX100 S2 - page 101

    101 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 2. Click [OK]. The [Initializ ation of ServerS tart core running] window a ppears and unattended installation will be started. Depending on the har dware configuration, th is process may take a few minutes. When the proc ess is completed, the [ Create a Serve ...

  • Fujitsu RX100 S2 - page 102

    102 Chapter 3 OS Installation Using Ser verS tart The server setup a nd OS installation have been completed. Refer t o "Chap ter 5 Op erations after OS Instal lation" (  pg.125) and perf orm necessary procedu res before starting server operati ons. ● In Preconfigurat ion Mode 1 Create a config uration file. For the creation procedure ...

  • Fujitsu RX100 S2 - page 103

    103 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart 3 .5 Installa tion on Multiple (the Second and Subsequent) Ser v er s This chapte r explains how to perform ins tallat ion on multip le servers us ing ServerS tart. By editing the configu ration fil e created for instal lation on t he first ser ver , you can ...

  • Fujitsu RX100 S2 - page 104

    104 Chapter 3 OS Installation Using Ser verS tart 3.5.2 Installation in Guided Mode Edit the configuration file and perform installation in guided mode. 1 T urn on the serv er and insert th e ServerS tart CD -ROM immediat ely . ServerStart starts up and a message a ppears prompting you to insert the ServerS tart floppy disk. 2 Insert the ServerS ta ...

  • Fujitsu RX100 S2 - page 105

    105 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 OS Installation Using ServerS tart Settings values in wizards  Setting items in wizards are se t to the values set on the first se rver . For insta llation on sub se- quent servers, you must change the foll owing items in the "OS inst allation wizard". For othe r items, cha nge th ...

  • Fujitsu RX100 S2 - page 106

    106 Chapter 3 OS Installation Using Ser verS tart 3 Insert the ServerS tart floppy disk copied in the preparatory pro cedure into t he floppy disk drive and cli ck [S tart here to c onfiguratio n file]. The [Open ServerS tart Configuration File] window appears. 4 S pecify "SerS tartBa tch.ini" on drive A and cli ck [Create] . The display ...

  • Fujitsu RX100 S2 - page 107

    107 Chapter 4 Manual OS Installa tion This chapter explains ho w to install the OS without using ServerS t art. 4.1 Creating Driver Di sks . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 08 4.2 S t arting Manual In stallati on . . . . . . . . . . . . . . . . . . . . . . . 1 13 4.3 Inst alling the LAN Dr iver . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 108

    108 Chapter 4 Ma nual OS Inst allati on 4 .1 Cr ea ting Driv er Disks When installing the server manu ally , it is nec essary to crea te driver installation disks beforehand. Also, driv er disks must be created when you add a n expansi on card during serv er operation. ■ Preparation for Crea ting Driver Disks Y ou need floppy disks for driver dis ...

  • Fujitsu RX100 S2 - page 109

    109 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation ■ For Windows 2000 S erver *1: Created from the ServerStart CD-ROM  The latest drivers, refer to the Fujitsu PRIMERGY website (http://pr imergy .fujitsu.com). 4.1.2 How to Create Driver Disks Driver disks are created from the ServerS tart CD-ROM using the ServerSt a ...

  • Fujitsu RX100 S2 - page 110

    110 Chapter 4 Ma nual OS Inst allati on When Windo ws NT is used, or if the CD ha s not been copied 1 Insert the S erverS tart CD-R OM into the cl ient computer' s CD-ROM dri ve. ServerStart sta rts up and the [W elcome to ServerStart] window appear s. ● When Creati ng a DOS Flop py Disk on the S erver 1 T urn on the serv er and insert th e ...

  • Fujitsu RX100 S2 - page 111

    111 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation 4 Click [or Inse rt a ServerSt art Floppy Disk to S tart ServerS tart]. The [W elcome to Serve rStart] window appea rs. 5 Eject the ServerS tart fl oppy disk. ...

  • Fujitsu RX100 S2 - page 112

    112 Chapter 4 Ma nual OS Inst allati on ■ Creat ing Driver Di sks Start up ServerStart a nd confirm that the [W elcome to ServerSt art] window is displayed . 1 Click [Floppy Builder]. The [ServerS tart FloppyBuilde r] window appears. 2 Click [Drivers Diskettes]. The [FloppyBuil der Driver Disk] window appears. 3 Click th e type of the driver you ...

  • Fujitsu RX100 S2 - page 113

    113 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation 4 .2 Star ting Manual Installa tion This section explains the p rocedures fo r installing the OS ma nually . 4.2.1 Installing Windows Server 2003 1 Create dri ver disk s. Prepare necessary dri vers before installing W indows Server 2003. Some drivers are crea ted from th ...

  • Fujitsu RX100 S2 - page 114

    114 Chapter 4 Ma nual OS Inst allati on 4 The [Wind ows Server 2003 Setup] window ap pears. The procedure dif fers depending on the connection of the installation ha rd disk. When installing the OS on a hard disk connected via the RAID card: Immediately , the following message appear s at the bottom of the window . Press the [F6] key .  This mes ...

  • Fujitsu RX100 S2 - page 115

    115 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation 7 Insta ll the chip set driv er . 1. Insert the ServerS tart CD-ROM into the drive of the server . When the ServerSta rt window appears, exit ServerSt art. 2. Execute the follow ing command on the ServerS tart CD-ROM. [CD-ROM drive]:DRIVERSChipSetIntelE7210Setup.exe ...

  • Fujitsu RX100 S2 - page 116

    116 Chapter 4 Ma nual OS Inst allati on 4.2.2 Installing Windows 2000 Server 1 Create dri ver disks . Prepare necessary dri vers before installing W indows 2000 Server . Some drivers used with W indows 2000 Server are created from the ServerS tart CD-ROM. For how to create dri ver disks, refer to "4. 1 Creating Driver Disks" (  pg.108) ...

  • Fujitsu RX100 S2 - page 117

    117 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation 2. When the "Please insert the disk labeled Manufacturer-supplied hardw are support disk into Drive A:" message appears, insert the driver disk created from the ServerS tart CD-ROM and press the [Enter] key . The following message appears. 3. Select the followi ...

  • Fujitsu RX100 S2 - page 118

    118 Chapter 4 Ma nual OS Inst allati on 9 Insta ll the USB 2. 0 driver . The procedure dif fers depending on whether Service Pack 4 is applied to the CD-ROM for the OS used. When Service Pack 4 is applied 1. Insert the ServerS tart CD-ROM into the drive of the server . When the ServerS tart window appears, exit ServerSt art. 2. Click [S tart] → [ ...

  • Fujitsu RX100 S2 - page 119

    119 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation 10 Insta ll the displ ay driver . 1. Insert the ServerS tart CD-ROM into the drive of the server . When the ServerSta rt window appears, exit ServerSt art. 2. Right-click the [My Co mputer] icon on the desktop and click [Manage] from the displayed men u. 3. Click [Device ...

  • Fujitsu RX100 S2 - page 120

    120 Chapter 4 Ma nual OS Inst allati on 4 .3 Installing the LAN Driv er This section explains the p rocedure fo r installing the driver . In addition to the case where the OS is installed manually , the driver must be installed when a LA N card is added. 4.3.1 Installing the LAN Dr iver (Windows Server 2003) The LAN driver inst allation procedure d ...

  • Fujitsu RX100 S2 - page 121

    121 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation • When a recognized network adapter is present Perform " ■ Updating LAN Drivers" (  pg.121) on the LAN device name under [Network adapters] , then " ■ Installing the LAN Dri ver" (  pg.122) on [Ethernet c ontroller] u nder [Other devices]. ...

  • Fujitsu RX100 S2 - page 122

    122 Chapter 4 Ma nual OS Inst allati on 4 Click [U pdate Driver ] in the [Driv er] tab w indow . The [W elcome to the Hardware Update W izard] window appears. 5 Select [I nstall the soft ware automati cally] and cl ick [Next] . The driver will be installed. 6 Click [Finish]. 7 Click [Close]. ■ Installing the LAN Driver Perform the following proc ...

  • Fujitsu RX100 S2 - page 123

    123 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Manual OS Installation 4.3.2 Installing the LAN Dr iver (Windows 2000 Server) 1 Insert the dr iver disk cr eated from the Se rverS tart CD-R OM into the serv er . 2 Right-cl ick the [My Compu ter] icon on th e desktop and sel ect [Manage] fr om the displa yed menu. 3 Click [Device M anager]. A ...

  • Fujitsu RX100 S2 - page 124

    124 Chapter 4 Ma nual OS Inst allati on •When the [Insert Disk ] window prompts you t o insert the "Int el PRO Adapter CD-ROM or floppy disk" or "In tel ® PRO/1000 Disk Driv er". Insert the driver disk created from the ServerS ta rt CD-ROM and install the dri ver .  The "Di gital signature w as not found " messag ...

  • Fujitsu RX100 S2 - page 125

    125 Chapter 5 Oper a tions after OS Installa tion This chapter explains the operations to be performed after OS inst a llation. Be sure to perform these operations before operating the server . 5.1 Memory Du mp/Paging File Set ting . . . . . . . . . . . . . . . . . . 126 5.2 Creating a Disk for System Recover y . . . . . . . . . . . . . . . . 135 5 ...

  • Fujitsu RX100 S2 - page 126

    126 Chapter 5 Oper ations af ter OS Inst allati on 5 .1 Memor y Dump/P a ging File Setting Before st art operat ing this serv er , configure the set ting for obt aining memory dump . The settin g procedure varies between Windows Server 2003 and Win dows 2000 Server . ● Memory Dump If memory dump is set, debugging information will be auto maticall ...

  • Fujitsu RX100 S2 - page 127

    127 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation ● Small Memory Du mp Minimum amount o f useful in formation for problem identificat ion is recor ded. If this option is specified, a new file is created eac h time the system unexpectedly stops. History of such files is stored in the direc tory displaye d in ...

  • Fujitsu RX100 S2 - page 128

    128 Chapter 5 Oper ations af ter OS Inst allati on 5 Set as follows: 1. In the [W rite debugging information] section, select the memory du mp file type. • Small memory dump (64KB) Minimum information is recorded to the memory dump file. Each time a fatal error occurs, a ne w file is created in the directory specified in [Small dump directory]. ? ...

  • Fujitsu RX100 S2 - page 129

    129 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5 Click the [Adv anced] tab. 6 Click [Change] in th e [Virtual memory] section . The [V irtual Memory] window appea rs. 7 S pecify the drive wher e the pagi ng file is to b e created. In [D rive], s elect the drive where th e system i s instal led. The selecte ...

  • Fujitsu RX100 S2 - page 130

    130 Chapter 5 Oper ations af ter OS Inst allati on 8 Select [C ustom size] an d enter a value i n [Initial size]. The value depe nds on the type of the set dump file. Specify a value la rger than the value shown in [Reco mmended] in [T otal pagin g file size for all drives].  Whe n a smaller v alue is specified for the pagi ng file size, perform ...

  • Fujitsu RX100 S2 - page 131

    131 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation • Required size Installed physica l memory × 1.3 ● Kernel Memory Dump Information of only kerne l memory space is recorded. When the system unexpectedly stops, the process that records informat ion to the log file is speeded up. Accordi ng to the amount o ...

  • Fujitsu RX100 S2 - page 132

    132 Chapter 5 Oper ations af ter OS Inst allati on 5 Click the [Adv anced] tab and click [S tartup a nd Recover y]. The [Startup and Recovery] window appears. 6 Set as follows: 1. In the [W rite debugging information] section, select the memory du mp file type. • Small memory dump (2MB or more) Minimum information is recorded to the memory dump f ...

  • Fujitsu RX100 S2 - page 133

    133 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation ■ P aging Fil e Setting Set up the paging file according to the following procedures: 1 Log on to the server wit h administrato r privileges. 2 Check free space of the dr ive where the system is installed. Check the required amount of free space ac cording t ...

  • Fujitsu RX100 S2 - page 134

    134 Chapter 5 Oper ations af ter OS Inst allati on 7 S pecify the drive wher e the pagi ng file is to be created. In [Drive], select th e drive where the sy stem is installed. The selected dr ive is displayed in [Drive] in [Paging file size for selected drive]. 8 S pecify the [Initial size]. The value depe nds on the type of the set dump file. Spec ...

  • Fujitsu RX100 S2 - page 135

    135 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5 .2 Cr ea ting a Disk f or System Re c ove r y If the inst allat ion of the OS was performed manual ly , create a syst em recovery disk .  If the system file, system configuration or environment setting change at startup, etc., are damaged, such data can b ...

  • Fujitsu RX100 S2 - page 136

    136 Chapter 5 Oper ations af ter OS Inst allati on 8 When the proc ess is completed, a mess age appears. Eject the floppy disk according to the message and pu t a label on it. Label example: W i ndows Automated Sy stem Recovery Disk: Backup.bkf, Cre ated at 12:00 04/ 01/2005 9 Click [OK] to e xit [Backup Ut ility]. 10 Click [Close] t o close the [B ...

  • Fujitsu RX100 S2 - page 137

    137 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5 .3 Storing the System Setting Inf or ma tion Before starting o perations, sto re the config uration inform ation of the BIOS setup utility . By storing this info rmation, the system can b e recovered with the store d informati on in case of a sys tem failur ...

  • Fujitsu RX100 S2 - page 138

    138 Chapter 5 Oper ations af ter OS Inst allati on 5.3.1 How to Store th e BIOS Information Store the BIOS information ac cording to the following procedures:  Before starting the operation, if the "OS Boot Monitoring" function of ServerView is enabled, disable it (it is disabled by default). If you start up the system while the " ...

  • Fujitsu RX100 S2 - page 139

    139 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5.3.2 Recovering the BIOS Information If the information configure d with the BIOS setup utility was deleted due to a dra in of the built-in server battery , etc., restore the BIOS information according to the following proced ures:  Do not turn off the ser ...

  • Fujitsu RX100 S2 - page 140

    140 Chapter 5 Oper ations af ter OS Inst allati on 6 If the foll owing have been set in the BIOS Setup Utili ty , rest art the system an d repeat S teps 1 to 4. The following settings when [Advanc ed] menu → [PCI Configuration] submenu → [Ethernet on Board] submenu → [PCI Device, Embedded Ethern et A] and [PCI Device, Embedded Ethernet B] are ...

  • Fujitsu RX100 S2 - page 141

    141 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5 .4 Cr ea ting Maintenance T ools This secti on explains how to create too ls for maint aining th e server . Maintenanc e tools are crea ted with the Fl oppyBuilder f unction of Ser verS tart. W ith the FloppyBuilder func tion of ServerStart, y ou can create ...

  • Fujitsu RX100 S2 - page 142

    142 Chapter 5 Oper ations af ter OS Inst allati on ■ Starting ServerSta rt ● For C reation on a Clien t Computer When the CD has been copied on W indow s 2000 Pro fessional/W indow s XP Professi onal 1 Click [S tart] → [Programs ] → [Fujitsu ServerSt art] → [Serve rS tart]. ServerStart sta rts up and the [W elcome to ServerStart] window a ...

  • Fujitsu RX100 S2 - page 143

    143 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 3 Click [OK]. The [ServerS tart FloppyBuilde r] window appears. 4 Click [or Inse rt a ServerSt art Floppy Disk to S tart ServerS tart]. The [W elcome to Serve rStart] window appea rs. 5 Eject the ServerS tart fl oppy disk. ...

  • Fujitsu RX100 S2 - page 144

    144 Chapter 5 Oper ations af ter OS Inst allati on ■ Creating a DOS Flo ppy Disk Start up ServerStart a nd confirm that the [W elcome to ServerSt art] window is displayed . 1 Click [Floppy Builder]. The [ServerS tart FloppyBuilde r] window appears. 2 Click [DOS Diske tte]. Insert the prepare d floppy disk by following the message. 3 Perform the s ...

  • Fujitsu RX100 S2 - page 145

    145 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5.4.2 Creating a Hardware Configuration T ool This section expla ins how to create a Hardware Configuration T ool from the ServerStar t CD-ROM. Prepare floppy disks as many as the tools you want to create before hand. T ypes of a Hardware Configuration T ool v ...

  • Fujitsu RX100 S2 - page 146

    146 Chapter 5 Oper ations af ter OS Inst allati on 5 .5 Notes Bef or e Oper a ting the Ser v er This secti on explains the settings required before starti ng to operate the s erver . For the respective settings, refer to "First Step Guide". • If a LAN car d was added, install a driver according t o "4.3 Installing the LAN Driver&qu ...

  • Fujitsu RX100 S2 - page 147

    147 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5.5.3 Drive Letter Assi gnment in Expert Mode In expert mode, you cannot specify a drive letter to a part icular partition arbitrari ly . Drive letters specified with Disk Manager in expert mode will be sequentially assigned from the first part ition with &quo ...

  • Fujitsu RX100 S2 - page 148

    148 Chapter 5 Oper ations af ter OS Inst allati on 5.5.4 Notes on Advanced Unin terruptible P ower Supply (UPS) Note the following points when using an advanc ed uninterruptible powe r supply (referre d to as UPS afterward). ■ UPS Shutdown Time Setting Specify enough ti me for the UPS power-of f time (time from the shutdown direction to the ac tu ...

  • Fujitsu RX100 S2 - page 149

    149 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation ■ BIOS Setup Uti lity Setting When power management is performed via a LAN, configure the settings as follows using the BIOS Setup Utility . 1 S tart the BIOS Setup Utility .  "8.2.1 Start ing and Exiting the BIOS Setup Utility" (pg.1 91) 2 From ...

  • Fujitsu RX100 S2 - page 150

    150 Chapter 5 Oper ations af ter OS Inst allati on 5 .6 LAN Driv er Advanced Setup Use "Intel ® PROSet" for LA N driver adva nced setup. 5.6.1 Intel ® PROSet ■ Intel ® PROSet Instal lation Usual ly , "Inte l ® PROSet" is installed with the driver . If Wi ndows Server 2003 or Windows 2000 Server is installed using t he flop ...

  • Fujitsu RX100 S2 - page 151

    151 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation • The controll ers of the onboard LAN a nd LAN cards are as foll ows: 5.6.2 Cautions for Onbo ard/PG-1852/1862/188x/189xLAN Driver V8.3 ■ Event Log Once a T eam is setu p, multiple i dentical logs from the s ame source that starts w ith the follow ing log ...

  • Fujitsu RX100 S2 - page 152

    152 Chapter 5 Oper ations af ter OS Inst allati on • When the T eaming function is being used, y ou cannot use W indows Load Balancing Service (WLBS) and Network Load Balancing (NLB). • PG-1852 does not become a member of a T eam.  Only a link down error b etween a LAN card (onboard LAN) and the switch it connects with, and the equivalent er ...

  • Fujitsu RX100 S2 - page 153

    153 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 Operations after OS Inst allation 5.6.4 VLAN ■ Notes When using a VLAN, note the following points. • Y ou can only have "NetBIOS over TCP/IP" enabled for up to four VLANs in the whole sy stem. • On a VLAN, do no t use protocols other tha n TCP/IP . • Y ou can only set ten or ...

  • Fujitsu RX100 S2 - page 154

    154 Chapter 5 Oper ations af ter OS Inst allati on 5.6.5 Local Address Setting Specify a local address accordi ng to the following proc edures. 1 S tart up "Intel ® PROSet ". The procedur e diff ers depending on the O S being used. For Windows Server 2003 1. Click [S tart] → [ Control Panel] → [Intel(R) PROSet]. For Windows 2000 Serv ...

  • Fujitsu RX100 S2 - page 155

    155 Chapter 6 High R elia bility T ools For stable PRIMERGY se rver operations, we recommend that high rel iability tools be installed. This chapter explains the installation and necessary settings of high reliability tools. 6.1 RAID Manag ement T ool (Global Arr ay Manager) . . . . . . . 1 56 6.2 S erver Monito ring T ool [ServerView] . . . . . . ...

  • Fujitsu RX100 S2 - page 156

    156 Chapter 6 High Reliability T ools 6 .1 RAID Mana gement T ool (Global Ar r ay Mana ger) RAID Management T ool is software that perform array configuration, disk initialization and disk ar ray monito ring when u sing RAID card. F or more details, re fer to "PRIMERGY Serve rBooks" supplied with the server , and "Supple ment" s ...

  • Fujitsu RX100 S2 - page 157

    157 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 High Reliability T ools ■ Error Window A ppearing after Instal lation (Windo ws Server 2003 only) If W indows Server 2003 Service Pack 1 is applied,when restart ing after installing/uninstall ing RAID Management T ool (Global Array Manag er) the pop up window that indicate SNMP service termi ...

  • Fujitsu RX100 S2 - page 158

    158 Chapter 6 High Reliability T ools 6 .2 Ser v er Monitoring T ool [Ser v erV iew] ServerV iew cons tantl y monitors the st atus of th e servers' har dware in the net work and provides a console wit h which the admi nistrator c an check the st atus of al l the servers at a glance. In ad dition, if an erro r occurs, the adm inistrator will be ...

  • Fujitsu RX100 S2 - page 159

    159 PRIMERGY RX100 S2 User ’s Guide 1 2 3 4 5 6 7 9 8 High Reliability T ools 6 .3 Solving Pr oblems Ear l y [DSNAP] DSNAP is a tool for collectively acquiring fa ilure investigat ion information such as server env ironment info rmation. OS installa tion using Server Start  When an OS is installed using ServerS tart, DSNAP is batch installed t ...

  • Fujitsu RX100 S2 - page 160

    160 Chapter 6 High Reliability T ools ...

  • Fujitsu RX100 S2 - page 161

    161 Chapter 7 Installing Inter nal Options This chapter explains how to install internal options on this server . Cont act an of fice listed in the "Contact Informati on" of "S tart Guide" regarding installation and removal of internal options. 7.1 B efore Installing Internal Op tions . . . . . . . . . . . . . . . . . . . 16 2 7 ...

  • Fujitsu RX100 S2 - page 162

    162 Chapter 7 Installing Internal Opt ions 7 .1 Bef or e Installing Inter nal Options The follow ing types of int ernal optio ns can be inst alled on thi s server .  When installing or removing devices, make s ure to use the removed screws on the same location and devices that were last installed or removed. Failure to do so can damage the devic ...

  • Fujitsu RX100 S2 - page 163

    163 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options • Devices inside the server remain hot after shutdown. W ait for a w hile after shutdown before installing or removing internal options. • The circuit boards and soldered parts of internal options are exposed. They can be damaged by static electricity . Before handling them, fi ...

  • Fujitsu RX100 S2 - page 164

    164 Chapter 7 Installing Internal Opt ions 7 .2 R emo ving and Attac hing the T op Co v er This secti on explains how to remove and at tach the t op cover . 7.2.1 Removing and Attaching the T op Cover ■ How to Remove the T o p Cover 1 Open the rack do or .  "1.4.1 Opening the Rack Door" (pg.28) 2 T urn of f the server and peripheral ...

  • Fujitsu RX100 S2 - page 165

    165 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 4 Slide the server . Pull the server out toward you until it clicks so that it locks in place on the rails on both sides. 5 Loosen the sc rew on the rear of th e server . 6 Slide the to p cover slowly to the rear and lift it to remove from the ser ver . ■ How to Attach the T o p ...

  • Fujitsu RX100 S2 - page 166

    166 Chapter 7 Installing Internal Opt ions 7 .3 Installing Memor y Modules Additional m emory will he lp to increase t he amount o f data to read at a time and improve the se rver processing capability . • Before installation or removal, turn off the server and all peripheral devices. Also unplug all power cables from the server . Failure to do s ...

  • Fujitsu RX100 S2 - page 167

    167 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 7.3.1 Where to Install Memory Modules Install memory modules in the memory slots on the ba seboard. A memory of this se rver contains a single Dual In-Line Memory Module (DIMM) and y ou can add a single memory module at a time. ■ Installat ion Order Install DIMMs in DIMM slots in ...

  • Fujitsu RX100 S2 - page 168

    168 Chapter 7 Installing Internal Opt ions 7.3.3 How to Install/ Remove Memory Modules 1 T urn of f the power and rem ove the top cover .  "7.2 Removing and Attaching the T op Cover" (pg.164) 2 T ouch a met al part of the server to discharge st atic ele ctricity . 3 Insta ll or remove memo ry modules. • Installing Insert a memory mod ...

  • Fujitsu RX100 S2 - page 169

    169 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 7.3.4 Defective Memory Disconnection F unction This server is equipped with the defecti ve memory (RAM module) disconnection function. This function disconnects the memory (one DIMM) judged to be defect ive (abnormal) during Power On Self T est (POST) to start the server . W hen PO ...

  • Fujitsu RX100 S2 - page 170

    170 Chapter 7 Installing Internal Opt ions 7 .4 Installing Expansion Car ds This sect ion explai ns the types of expansi on card, in stall ation procedu res, and note s on expansion cards. 7.4.1 Where to Instal l an Expansion Card This server has two PCI slots. Up to two expansion cards can be installed. The figure below shows the slot locations. ? ...

  • Fujitsu RX100 S2 - page 171

    171 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options ■ PCI Slot Specifications • PCI slots 1 and 2 are both 64-bit, 66MHz PCI slots. • PCI slot 1 can be used for a LowProfile PCI card only . • The PCI slots conform to the PCI local bus specificat ions (Rev . 2.2). 7.4.2 Installable Exp ansion Cards and Notes This section expl ...

  • Fujitsu RX100 S2 - page 172

    172 Chapter 7 Installing Internal Opt ions ■ Notes on Inst allation ● Drivers For expansion card dri vers, refer to "2.3.5 Expansion Cards Supported by ServerSt art" (  pg.46). ● Notes on Each Card For notes of specific expansion card, refe r to the manuals supplied with the card and the notes provided with the server . Also, che ...

  • Fujitsu RX100 S2 - page 173

    173 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options • Connecting the hard disk access LED cable If you conne ct an internal ha rd disk unit to the o ptional SCSI Ctrl U160 lp (PG-130L ) or RAID Ctrl 1-Channel 64 MB (PG-141C1L), install the SCSI Ctrl U160 lp (PG-130L) or RAID Ctrl 1-Channel 64 MB (PG-141C1L) first. Then, connect th ...

  • Fujitsu RX100 S2 - page 174

    174 Chapter 7 Installing Internal Opt ions 7.4.3 How to Install an Expansion Card 1 T urn of f the power and rem ove the top cover .  "7.2 Removing and Attaching the T op Cover" (pg.164) 2 T ouch a met al part of the server to discharge st atic ele ctricity . 3 Unplug the ca ble from the SC SI or RAID car d instal led in Slot 1. Unplug ...

  • Fujitsu RX100 S2 - page 175

    175 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 5 Remove th e expansion card a nd the slot co ver from the card locking fr ame.  The slot cover for PCI slot 2 is composed of a LowProfile slot cover an d an Extension slot cover.  Be sure to kee p the remov ed slot cov er for later us e. 6 When installing a LowProf ile card, ...

  • Fujitsu RX100 S2 - page 176

    176 Chapter 7 Installing Internal Opt ions  When installing tw o expansion c ards on PCI slot 1 and 2, i nsert a card in to PCI slo t 2 first, th en insert othe r the card into P CI slot 1. If a card has already been insert ed i nto slot 1, remov e it. Insert a card int o slot 2 first, then insert anot her into slot 1. 8 Insert the ex pansio n c ...

  • Fujitsu RX100 S2 - page 177

    177 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 7 .5 Installing an Inter nal CD-R OM Driv e Unit This section explains the procedure for installing a CD-ROM drive (option al). 7.5.1 Installable CD-ROM Drive Units The following CD-ROM drive units can be installe d on this server . Pac k ag e  Before installing the internal CD- ...

  • Fujitsu RX100 S2 - page 178

    178 Chapter 7 Installing Internal Opt ions 7.5.2 How to Install the In ternal CD-ROM Drive Unit 1 T urn of f the power and rem ove the top cover .  "7.2 Removing and Attaching the T op Cover" (pg.164) 2 T ouch a met al part of the server to discharge st atic ele ctricity . 3 Loosen the sc rews of the dummy uni t, and remove the dummy u ...

  • Fujitsu RX100 S2 - page 179

    179 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 2. Slide the CR-ROM drive forward and tighten the screw s. 5 Connect the I DE and power cab les. Use the IDE and power cables connected to the server . Fix the connecte d cables between the pieces of the foam. 6 Atta ch the top cover .  "7.2 Removing and Attaching the T op ...

  • Fujitsu RX100 S2 - page 180

    180 Chapter 7 Installing Internal Opt ions 7 .6 Installing an Inter nal Har d Disk Unit This section explains how t o install internal har d disk units. 7.6.1 Installation Location of Internal Hard Disk Unit ■ Order of Internal Hard Disk Unit Instal lation Install the internal hard disk unit to ba y 1 first, then bay 2. • The circuit boards and ...

  • Fujitsu RX100 S2 - page 181

    181 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options ■ SC SI-ID Setting of Interna l Hard Disk Unit The internal hard di sk unit does not support hot-swapping. As the SCSI-ID is not set a utomatically , you must set it up in a dvance by ref erring to the followings. ● Jumper Pin L ocations of t he Internal Ha rd Disk Unit Set the ...

  • Fujitsu RX100 S2 - page 182

    182 Chapter 7 Installing Internal Opt ions 7.6.2 Installable Internal Hard Disk Units ■ Installable Internal Ha rd Disk Units The following inte rnal hard disk units ca n be installed on t his server . Pac k ag e  When an internal hard disk unit is connected to the SCSI card, it operates as the Ultra160 SCSI device .  Before installing the ...

  • Fujitsu RX100 S2 - page 183

    183 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 7.6.3 How to Install the In ternal Hard Disk Unit 1 T urn of f the power and rem ove the top cover .  "7.2 Removing and Attaching the T op Cover" (pg.164) 2 T ouch a met al part of the server to discharge st atic ele ctricity . 3 Disconnect the extension cables of the ...

  • Fujitsu RX100 S2 - page 184

    184 Chapter 7 Installing Internal Opt ions 5 Remove the bay to accommodate an in ternal hard dis k unit. Loosen the screws (1) and slid the bay towar d you to remove it (2). 6 Insta ll the inter nal hard disk un it to the hard di sk bay . Fasten the bay to the internal hard disk unit using the screws supplied with the disk unit. 1 2 Hard disk bay ...

  • Fujitsu RX100 S2 - page 185

    185 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 7 Insta ll the hard dis k bay to the server . Insert the hard disk bay with the internal ha rd disk unit into the server (1), and tighten the screws (2). 8 Connect SC SI and power cabl es. Connect the SCSI ca ble to the SCSI connec tor of the internal hard disk unit. Also, c onnect ...

  • Fujitsu RX100 S2 - page 186

    186 Chapter 7 Installing Internal Opt ions If no SC SI card or RAID card is install ed for the diskle ss type  Instal l the optional SCSI Ctrl U160 lp (PG-130 L) or RAID Ctrl 1-Chan nel 64 MB (PG-141C1L), and connect the in ternal hard disk uni t to the SC SI Ctrl U 160 l p (P G-130L) or R AID Ctrl 1- Channel 64 MB ( PG-141C1L) using the SCSI ca ...

  • Fujitsu RX100 S2 - page 187

    187 PRIMERGY RX100 S2 User ’s Guide 7 Installing Internal Options 7 .7 Connection of Optional De vices This secti on explains the connectio n of optional de vices. 7.7.1 Connection Examples of Internal Option Devices The following shows connection examples of inte rnal option devices. Connection condi tions vary depending on example s. See each e ...

  • Fujitsu RX100 S2 - page 188

    188 Chapter 7 Installing Internal Opt ions 7.7.2 Connecting an External SC SI Option External SCSI options c an be connected via the SCSI card as fol lows. ■ Connection of a Backup Cabinet Connect the backup cabine t as shown below . Only a singl e backup cabinet c an be connected t o the server . Baseboard SCSI cable (PG-CBLS007 / PG-CBLS008 : O ...

  • Fujitsu RX100 S2 - page 189

    189 Chapter 8 Har d ware Configur a tion/ Utilities This chapter explains how to make the environment settings nec essary to operate the server . 8.1 Jumper Pin Set tings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 90 8.2 B IOS Setup Uti lity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 ...

  • Fujitsu RX100 S2 - page 190

    190 Chapter 8 Hardware C onfiguration/Utilit ies 8 .1 J umper Pin Settings This secti on explains the jumper pins . 8.1.1 Jumper Pin Setup Procedure 1 T urn of f the power and rem ove the top cover .  "7.2 Removing and Attaching the T op Cover" (pg.164) 2 T ouch a met al part of the server to discharge st atic ele ctricity . 3 Remove t ...

  • Fujitsu RX100 S2 - page 191

    191 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8 .2 BIOS Setup Utility This secti on explains settings for the BIOS Setu p Utility and i tems regardin g each setting. 8.2.1 Starting and Exiti ng the BIOS Setup Utility The following expl ains how to start and e xit the BIOS Setup Utilit y . ■ How to Start the BIOS Setup U ...

  • Fujitsu RX100 S2 - page 192

    192 Chapter 8 Hardware C onfiguration/Utilit ies ● Key Operat ions in the BIOS Setup Util ity The roles of the keys used for using the BI OS Setup Utility are as follows: ■ How to Exit the BIOS Setup Utility 1 Use the [ ← ] [ → ] ke ys to display the [ Exit] menu. table: List of Key Operations on the BIOS Setup Utility Window Key Descriptio ...

  • Fujitsu RX100 S2 - page 193

    193 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 2 Use the [ ↑ ] [ ↓ ] keys to select the exit mode . • T o save configuration changes b efore exiting: Move t he curso r to [Sa ve Chan ges & Ex it] and press t he [Enter ] key . The mes sage "S ave configuration changes and exi t now?" is displayed. • T ...

  • Fujitsu RX100 S2 - page 194

    194 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.2 Main Menu The [Main] menu window is initially displa yed when you start the BIOS Setup Utility . Settings for time and date and for the drives are confi gured in the [Main] menu window . table: Items on the Main Menu Item Setting Description System Time Present tim e The system tim e is set in ...

  • Fujitsu RX100 S2 - page 195

    195 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.3 P arallel A T A Submenu Appear s when [Parallel A T A ] is s elected fr om the [Main] menu. Sets the ty pe and operating mode for the connected i nternal hard disk unit. table: Items on the Parallel A T A Submenu Item Setting Description T ype Auto (Fixed parameter) Sets ...

  • Fujitsu RX100 S2 - page 196

    196 Chapter 8 Hardware C onfiguration/Utilit ies PIO Mode - (Fixed parameter) Sets the Programm ed I/O (PIO) data transfer m ode. When [T ype] is set to [Auto], the current settings appear . It can be set when [T ype] is set to [CD-ROM], [Other A T API], [A T API Removable], [IDE Removable] or [User]. 32 Bit I/O Disabled (Fixed parameter) Specifies ...

  • Fujitsu RX100 S2 - page 197

    197 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.4 Boot Options Submenu Appear s when [Boot Op tions ] is s elected fr om the [ Main] menu. Sets system start up options. table: Items on the Boot Options Submenu Item Setting Description POST Errors Enabled (Fixed param eter) Sets whether or not to stop the boot process an ...

  • Fujitsu RX100 S2 - page 198

    198 Chapter 8 Hardware C onfiguration/Utilit ies ■ Boot Sequence Submenu Sets the order of selected drives to boot the OS. table: Items on the Boot Sequence Submenu Item Description (The boot order is described.) • CD-ROM Drive • Removable Devices • Hard Drive • IBA GE Slot 0208 v1217 • IBA GE Slot 0430 v1217 [IBA GE Slot 0208 v1217] an ...

  • Fujitsu RX100 S2 - page 199

    199 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.5 Advanced Menu Configures peripheral and PCI device s. table: Items on the Advanced Menu Item Setting Description Peripheral Configuration [Enter] Configures the serial port, parallel port, etc.  "8.2.6 Peripheral Configuration Su bmenu" (pg.20 0) PCI Configu ...

  • Fujitsu RX100 S2 - page 200

    200 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.6 Peripheral Configuration Submenu Appears when [Peripheral Configuration] is selecte d from the [Advanced] menu. Configures the serial ports, parallel port s, etc. S-A T A Interface Enabled (Fixed param eter) This option is not used by the server . S-A T A Mode Legacy IDE (Fixed parameter) It ca ...

  • Fujitsu RX100 S2 - page 201

    201 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities Serial Multiplexer • System • BMC (at the tim e of purcha se) • Shared Changes the function of the serial port. • System Used as a serial port. •B M C Enables the remote control function. "Appendix C Remote Control Function and Console Redirection" (  pg ...

  • Fujitsu RX100 S2 - page 202

    202 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.7 PCI Configuration Submenu Appears when [PCI Configura tion] is selected from the [Advanced] menu. Configures the PCI devices. table: Items on the PCI Configuration Submenu Item Setting Description Ethernet on Board [Enter] Configures the LAN controller on the baseboard.  " ■ Ethernet ...

  • Fujitsu RX100 S2 - page 203

    203 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities ■ Ethernet on Board Submen u Configures the LAN controller on the baseboa rd. ■ PCI IRQ Con figuration Submenu Sets PCI IRQs for the PCI slots. ■ PCI SL OTS Configura tion Submenu Configures the PCI slots. table: Items on the Ethernet on Board Submenu Item Setting Descri ...

  • Fujitsu RX100 S2 - page 204

    204 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.8 Advanced System Configuration Submenu Appears when [Advanced System Configuration] is sel ected from the [Advance d] menu. The submenu configures a dditional settings. table: Items on the Advanced System Configuration Submenu Item Setting Description CPU Settings [Enter] Configures the CPU cloc ...

  • Fujitsu RX100 S2 - page 205

    205 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities ■ CPU Settings Submenu Sets the CPU clock frequency , etc. table: Items on the CPU Settings Submenu Item Setting Description CPU Mismatch D etection Enabled (F ixed parameter) Sets whether to enable or disable the CPU clock frequency checking. Hyper Threading • Disabled ? ...

  • Fujitsu RX100 S2 - page 206

    206 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.9 Power On/Off Submenu Appears when [Power On/Of f] is selected from th e [Advanced] menu. Configures power On/Off setti ngs. table: Items on the Power On/Off Submenu Item Setting Description Remote • Disabled • Enabled (at the tim e of purcha se) Sets whether or not the power can be turned o ...

  • Fujitsu RX100 S2 - page 207

    207 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.10 Security Menu Configures the security features. table: Items on the Security Menu Item Setting Description Setup Password/System Passwo rd - Displays whether each password is set. [Not installed] appears when the password is not set, and [Installed] appears when it is s ...

  • Fujitsu RX100 S2 - page 208

    208 Chapter 8 Hardware C onfiguration/Utilit ies V irus W arning Disabled ( Fixed parame ter) Sets whether or not to check for changes in th e boot sector of the hard disk drive after the previous system startup. If the boot secto r is changed wit hout a clear reason, it is necessary to scan the system for computer viruses with a virus detection pr ...

  • Fujitsu RX100 S2 - page 209

    209 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.11 Server Menu Configures server settings. table: Items on the Server Menu Item Setting Description O/S Boot Timeout • Disabled (at the tim e of purcha se) • Enabled Sets whether to enable or disable the OS Boot Monitoring function, when ServerV iew is installed to the ...

  • Fujitsu RX100 S2 - page 210

    210 Chapter 8 Hardware C onfiguration/Utilit ies Mode • Continue (at the time of purcha se) • Reset • Power Cycle Sets the operation to be performed when a tim eout occurs during OS boot monitoring. • Continue: The boot sequence is continued. • Reset: The server restarts automatically and starts POST . • Power Cycle: The server turns of ...

  • Fujitsu RX100 S2 - page 211

    211 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.12 IPMI Submenu Appear s when [IPMI] is sel ected fro m the [S erver] menu. Configures the Baseboard Management Cont roller (BMC). table: Items on the IPMI Submenu Item Setting Description IPMI Specification V ersion - Displays the IPMI Specification version. BMC Firmwa re ...

  • Fujitsu RX100 S2 - page 212

    212 Chapter 8 Hardware C onfiguration/Utilit ies ■ LAN Settin gs Submenu These menu items are fixed on this server . If you need to configure the LAN setup incl uding IP addresses, refer to "9.3.4 Before Using the Remote Control Service" (  pg.242) and use the Server Management T ools. 8.2.13 CPU Stat us Submenu Appear s when [CP U S ...

  • Fujitsu RX100 S2 - page 213

    213 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities 8.2.14 Memory St atus Submenu Appears when [Memory Status] is select ed from the [Server] menu. This submenu sets whether or not to allow the use of the installed memory . table: Items on the Memory S tatus Submenu Item Setting Description DIMM 0 • Enabled (at the tim e of p ...

  • Fujitsu RX100 S2 - page 214

    214 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.15 Console Redirection Submenu Appears when [Console Re direction] is selected f rom the [Server] menu. This submenu configures detailed setti ngs for console redirection. table: Items on the Console Redirection Submenu Item Setting Description Console Redirection Port • Disabled (at the time o ...

  • Fujitsu RX100 S2 - page 215

    215 PRIMERGY RX100 S2 User ’s Guide 8 Hardware Configuration/Utilities Baud Rate • 300 • 1200 • 2400 • 9600 (at the time of purcha se) • 19.2K • 38.4K • 57.6K • 1 15.2K Sets the baud rate for console redirection. This item appears when [Console Redirection Port] is set to [Enabled]. Protocol • VT100 • VT100, 8bit • PC-ANSI, ...

  • Fujitsu RX100 S2 - page 216

    216 Chapter 8 Hardware C onfiguration/Utilit ies 8.2.16 Exit Menu Exits BI OS Setu p. table: Items on the Exit Menu Item Description Save Changes & Exit Saves the current settings on the CMOS and exits the BIOS Setup Utility . The server restarts at the sam e time. Get Default V alues Loads and displays the default settings for the server . Not ...

  • Fujitsu RX100 S2 - page 217

    217 Chapter 9 Oper a tion and Maintenance This chapter explains the operations necessary after st arting to use this server as well as daily care and maintenance. 9.1 Daily Maint enance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 9.2 T roubleshoot ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 9.3 System E ...

  • Fujitsu RX100 S2 - page 218

    218 Chapter 9 Oper ation and Mai ntenance 9 .1 Dail y Maintenance This sect ion explain s how to check the stat us of the operat ing server , as wel l as how to perform daily maint enance. 9.1.1 Checking the Server Condition Use the status LED or server monitoring tool t o check the server status. ■ Checking Ea ch LED This server is equipped with ...

  • Fujitsu RX100 S2 - page 219

    219 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance  In dusty environments, dust piles up on the front and rear panels of the server over short periods. Install the server in a dif ferent location to avoid failures. ■ Cleaning the Server Interior In dusty environments, dust deposits on the serve r . Dust deposits may cause a serv ...

  • Fujitsu RX100 S2 - page 220

    220 Chapter 9 Oper ation and Mai ntenance 2 Remove th e ball and rins e it with water . Flip the mouse over to remove the ball. Afterwards, wash it with wate r . 3 Clean the inside of the m ouse. W ipe the inside of the mouse, the roller , and the bottom cover with a damp cloth. 4 Insert the ba ll and apply the c over . After the ball and inside of ...

  • Fujitsu RX100 S2 - page 221

    221 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9 .2 T r oubleshooting This sect ion explai ns the resol utions when the server i s not runni ng properly or w hen error messag es are displayed . For each situation, refer to the fol lowing. If the problem is not resolved after performing the following troubleshooting, contac t an o ...

  • Fujitsu RX100 S2 - page 222

    222 Chapter 9 Oper ation and Mai ntenance ■ Display ( or Monitor ) ● The displa y does not power on. Check to see whether the power cabl e of the display is properly connec ted to the outlet. For details, refer to "Start Guide" or the manual of the display . ● The screen display i s distorted when the Lin ux system is shut down. Whe ...

  • Fujitsu RX100 S2 - page 223

    223 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ● Cannot write t o the floppy disk. The write protection of the floppy disk may be applied. Flip the switch on the disk to allow writing. ■ CD-ROM Drive Unit ● Cannot re ad data. • Check to see whether the CD-ROM is inserted prope rly . If it is not inserted, correctly insert ...

  • Fujitsu RX100 S2 - page 224

    224 Chapter 9 Oper ation and Mai ntenance • If the extension cable is unplug ged from the baseboard connector Connect the ca ble by referri ng to the following ta ble. ■ SC SI Devices ● The unit d oes not opera te properly . Refer to "Connection via the SCSI Card" of "7.7 Connect ion of Optional Devices" (  pg.187). • ...

  • Fujitsu RX100 S2 - page 225

    225 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ● Notes on AC Po wer-Off If you turn the AC power of f when the system is on, the PSU Supply Failure log may be stored. If the AC Lost log is stored simultaneously as shown below , this will not a ffect server operation. Y ou can continue t o use the server without taking any a cti ...

  • Fujitsu RX100 S2 - page 226

    226 Chapter 9 Oper ation and Mai ntenance 9.2.2 Error Messages This section expla ins the error messages for t his server . ■ POST Error Message s This section e xplains error messag es of POST (Power On Self T est: a devi ce check perfo rmed during the server startup). If an error occurs during POST , the following messages are display ed. table ...

  • Fujitsu RX100 S2 - page 227

    227 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance System timer err or Turn the server off and b ack on. If the message still appears, the baseboard must be replaced. Contact an office listed in the "Contact Information" of "Start Guide". Real time cl ock error Check the date and time settings on the "8.2.2 M ...

  • Fujitsu RX100 S2 - page 228

    228 Chapter 9 Oper ation and Mai ntenance CPU disable! CPU is no longer available for the operating system. The CPU is abnormal. Contact a n of fice listed in the "Contact Information" of "Start Guide". Invalid System Configuration Data Change [Reset Configuration Data] on "8.2.5 Advanced Menu" (  pg.199) to [Y es] ...

  • Fujitsu RX100 S2 - page 229

    229 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ■ Server Manage ment T oo ls Error Messages The following error messages may appe ar while executing Server Manageme nt T ools. Perform the corresponding resolution listed in the table. If messages other than the following are display ed, contact an office l isted i n the "C o ...

  • Fujitsu RX100 S2 - page 230

    230 Chapter 9 Oper ation and Mai ntenance 9.2.3 Software T roubleshooting This section expla ins software related t roubleshooting. For troubles du ring OS installation or sy stem operation, refer to the following cont ents. ■ T rouble a t a ServerStart Startup ● After a boot fro m the ServerStart CD-ROM, nothin g is displayed on the screen. Th ...

  • Fujitsu RX100 S2 - page 231

    231 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ■ Err or Window App earing aft er Install ation or Unin stallation of ServerV iew or RAI D Management T ool (Global Arra y Manager) on Windows S erver 2003 Systems with W indows Server 2003 Service Pack 1 may display the following popup message a t the next startup after instal lat ...

  • Fujitsu RX100 S2 - page 232

    232 Chapter 9 Oper ation and Mai ntenance ● The "Windows - T oo small virtua l memory size" message appear s after completion of "Create S erverStart Flop py Disk". This message may be displayed whe n no disk array is configured and ServerS tart is starte d during 256MB memory OS installation on the hard disk connec ted to the ...

  • Fujitsu RX100 S2 - page 233

    233 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance Clicking [Finish] in this window displa ys the [Help and Support Center] window . Click [X] to close this window . The "!" mark is displayed at the LAN devic e name in Device Manager . Device names are displayed properly when all LAN drive rs are installed and the system is ...

  • Fujitsu RX100 S2 - page 234

    234 Chapter 9 Oper ation and Mai ntenance ■ Event Log Errors after Installa tion After W indows Server 2003 or W indows 2000 Server has been installed, the follo wing events may be displayed i n Event V iewer . Check and perform the correct ive action against the relevant event . table: Error events at inst allation ID Description Cause and corre ...

  • Fujitsu RX100 S2 - page 235

    235 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ■ Cannot C ollect the Mem ory Dump If the memory dump file cannot be crea ted, perform the following procedures. ● Correct the sett ings If the memory d ump cannot be collect ed, check the set tings of the paging fil e and memory dump fil e. For setting procedure s, refer to &quo ...

  • Fujitsu RX100 S2 - page 236

    236 Chapter 9 Oper ation and Mai ntenance ■ F ails in Remote Inst allation If remote installat ion fails, check t he following. ● Checking Servi ces Check that the DHCP , PXE Service, and TFTP Service are runni ng. For checking proced ures, refer to "3.4 Re mote Installation" (  p g.85). ● Setting TFTP T o access TFTP Service, ad ...

  • Fujitsu RX100 S2 - page 237

    237 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ■ SNMP Service Startu p F ails Regardless of whether the Simple Network Management Protocol (SNMP) is installed, if the SNMP service is not started, perform the followi ng procedure to start the SNMP service. ● For Windows Serv er 2003 1 Click [S ta rt] → [Admini strative T ool ...

  • Fujitsu RX100 S2 - page 238

    238 Chapter 9 Oper ation and Mai ntenance ● Changing th e Time Sett ings for the OS a nd Hardware C lock In a Linux environment , the time display ed on the OS (the software clock value on the OS) is written to the hardware clock on the server when the OS is shut down. • Procedure for prohibiting the time on the OS from being written to the har ...

  • Fujitsu RX100 S2 - page 239

    239 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9 .3 System Ev ent Log T o operate system event l og, use the [IP MI] submenu of the [ Server] menu in B IOS Setup Utility and the Serv er Managem ent T ools.  When the area for writing to the sy stem event log is full, the server is set to automatically overwrite older event logs ...

  • Fujitsu RX100 S2 - page 240

    240 Chapter 9 Oper ation and Mai ntenance 1 Insert the " Server Manageme nt T ools" dis k supplied w ith this ser ver into the floppy disk drive. The system will boot from the floppy disk and the DOS prompt is displayed. 2 Enter the followin g command and pr ess the [Enter] key . A:SMT>IPM IVIEW .EXE The menu window of Server Manageme ...

  • Fujitsu RX100 S2 - page 241

    241 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 2 Use the [ ↑ ] and [ ↓ ] keys to select [ System Event Log (S EL)], and pres s the [Enter] key . The [SYSTEM EVENT LOG (SEL)] window appears. 3 Use the fo llowing key op erations to scr oll the window a nd check the contents. [ ↑ ], [ ↓ ], [ ← ], [ → ], [PageUp], [PageDo ...

  • Fujitsu RX100 S2 - page 242

    242 Chapter 9 Oper ation and Mai ntenance ■ Deleting the System Even t Log 1 S tart Server Ma nagement T ools. The menu window of Server Management T ools appears. 2 Use the [ ↑ ] and [ ↓ ] keys to select [S ystem Event L og (SEL)], and press the [Enter] key . The [SYSTEM EVENT LOG (SEL)] window appears. 3 Press the [F 3] key . The confirmati ...

  • Fujitsu RX100 S2 - page 243

    243 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 2 S tart Server Ma nagement T ools. 3 Select [User Managemen t] and press t he [Enter] key . The [USER MANAGEMENT] window appea rs. 4 Set the password in [Administrat or] for ID 3. 1. Select an [ID] and press the [Enter] key . 2. S pecify the [User Name] and [Password] and set the [O ...

  • Fujitsu RX100 S2 - page 244

    244 Chapter 9 Oper ation and Mai ntenance 9 .4 Securities Security f eatures are prov ided in order to protect the serv er hardware and s oftware from theft. Additional security function s, which prevent unauthorized use , provided by the BIOS S etup Utility ar e also available to help maintain a highly reliable data security s ystem. 9.4.1 Hardwar ...

  • Fujitsu RX100 S2 - page 245

    245 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9.4.2 Security against Unauthorized Use A password can be set to prevent unauthorized use of the serve r . When a password is set, the server is accessible only to the users who know the password. The password is set in the BIOS Setup Utility . F or details on the BIOS Setup Utility ...

  • Fujitsu RX100 S2 - page 246

    246 Chapter 9 Oper ation and Mai ntenance  When only the user or administrator password is set, the same setting items are accessible to both users and administrators.  When both passwords are set, users can set dates and user passwords only . ■ Changing/D eleting a P assword 1 Enter the current password in the [Enter Cu rrent Password ] fi ...

  • Fujitsu RX100 S2 - page 247

    247 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9.4.3 Security When Disposing the Server ■ Notes regardin g the Deletio n of Data f rom the Hard Dis k When Disposing or T ransferring the Server When disposing or transferring a server that has been use d, the data in the hard disk may be read and used unscrupulously . T o prevent ...

  • Fujitsu RX100 S2 - page 248

    248 Chapter 9 Oper ation and Mai ntenance 9.5 B ac ku p This server utilizes high re liability compo nents and hard d isks, however , as a precautio nary measure, it i s recommended th at periodic ba ckups be t aken of the data. 9.5.1 Importance of Backups If the data on the server is backed up, it can be re stored from the backup da ta in the even ...

  • Fujitsu RX100 S2 - page 249

    249 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance ■ Notes on Opera ting Backups Notes on operating backups are as follows. For details, refe r to the device manua ls. ● Head Cleani ng Airborne dust and dust from th e magnetic media can c ollect on the hea d of the magnetic tape device. T o remove this dust, head cleaning must be ...

  • Fujitsu RX100 S2 - page 250

    250 Chapter 9 Oper ation and Mai ntenance ● Ejecting Medi a after a Bac kup Some backup software produc ts provide functions for e jecting media afte r a backup is complete d. Such functions will rewind the tape after a backup is completed and then eject t he media from the drive. Be sure to exec ute this function for a utoloader/library devices. ...

  • Fujitsu RX100 S2 - page 251

    251 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9 .6 R estoring the System In the unfor tunate event w here the system file, syste m configurat ion, or envir onment changes dur ing startup are corrupte d, use the repair informatio n stored on the recovery dis k created at the instal lation to res tore the system.  Create a reco ...

  • Fujitsu RX100 S2 - page 252

    252 Chapter 9 Oper ation and Mai ntenance 9.6.2 F or Windows 2000 Server ● Items Required • W indows 2000 Server CD-ROM • W indows 2000 Server system recovery disk (created beforehand) • W indows 2000 Server First Step Guide 1 Follow "W indows 2000 Ser ver First S tep Guide" to start W indows 2000 Serv er setup. 2 From the [W elco ...

  • Fujitsu RX100 S2 - page 253

    253 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9 .7 R einstalling the OS This section explains the procedure for reinstalling the O S. 9.7.1 Checking before OS Reinstallation ■ Removing the Optio nal Devices Remove the following optional devices before reinstallation. In stall or connect the m after OS installation. • Optiona ...

  • Fujitsu RX100 S2 - page 254

    254 Chapter 9 Oper ation and Mai ntenance 9 .8 Changing OS Settings When you have cha nged to enable or di sable Hyper-Th reading using the BIOS setting after starting opera tion, change the OS to th e uni-processor ke rnel or multi- processor ke rnel.  Customers using the Linux distribution OS are advised to refer to the Fujitsu PRIMERGY web si ...

  • Fujitsu RX100 S2 - page 255

    255 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 5 Update dri vers. 1. Click [Next] in the [S tart Device Driver Upgrade Wizard] w indow . The [Install Hardware Device Driver] window appears. 2. In search method selection, select [Display known drivers for this device and select a driver from the list.] and click [Next]. The [Sel e ...

  • Fujitsu RX100 S2 - page 256

    256 Chapter 9 Oper ation and Mai ntenance 6 Shut down and t urn off t he server . 1. Click [Close]. The [System Settings Change] window appear s. 2. Click [Y es]. The computer shuts down and restarts automatical ly . 7 Add an optional CPU or ch ange the Hyper-T hreading setting in the BIO S Setup Utility .  "8.2.1 Starti ng and Exiting the ...

  • Fujitsu RX100 S2 - page 257

    257 PRIMERGY RX100 S2 User ’s Guide 9 Operation and Maintenance 9 .9 Maintenance Ser vice This secti on explains the detai ls of the maint enance servi ce. If the cause of the failure is uncert ain or if the or iginal condi tion cannot be restored, contact the seller or an office listed in the "Co ntact Information" of "S tart Guid ...

  • Fujitsu RX100 S2 - page 258

    258 Chapter 9 Oper ation and Mai ntenance 9.9.2 Contacting Maintenance Support For "Contact Information", refer to "St art Guide". Before c ontacting maintenance support, check the following. • Model name and product ID of the server They are descri bed on the label on the server . For the label location, refer to "S tart ...

  • Fujitsu RX100 S2 - page 259

    259 Appendix This section explains th e specifications for the server and internal options. It also covers how to recycle the products. A Server S pecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 60 B Specifications for Interna l Options . . . . . . . . . . . . . . . . . . 261 C Remote Control Fun ction and Console Redir ecti ...

  • Fujitsu RX100 S2 - page 260

    260 Appendi x A Ser v e r Specifica tions This secti on explains the server and in ternal optio n specifica tions. A .1 Diskless type *1: A low profile PCI card can be inserted i nto the standard PCI s lot if the extensio n slot cover is insta lled. The specific ations for the server a re subject to ch ange for the purpose of im provement wi thout ...

  • Fujitsu RX100 S2 - page 261

    261 PRIMERGY RX100 S2 User ’s Guide Appendix A B Specifications f or Inter nal Options This secti on explains the specifi cations for i nternal opti ons for the serv er . When you have b ought an inter nal option as a standar d option, che ck the conten ts of the option al packa ge before use. S hould it hap pen that items are missing , contac t ...

  • Fujitsu RX100 S2 - page 262

    262 Appendi x B.2 Internal CD -ROM Dr ive Unit Specifications ■ Pa c k a g e • Internal CD-ROM Drive Unit (1) ■ Specifications B.3 Internal Hard Disk Unit Specifications ■ Pa c k a g e • Internal hard disk unit (1) • 4 setscrews ■ Specifications *1: Switched autom atically according to the SC SI environment. *2: The value indicates me ...

  • Fujitsu RX100 S2 - page 263

    263 PRIMERGY RX100 S2 User ’s Guide Appendix A B.4 Power Cord Selection The power cord for this unit has been packed separa tely and has been select ed according to the country of destination. I t must be used to prevent e lectric shock. Use t he following guideline s if it is necessary to replace the original c ord set. The female receptacl e of ...

  • Fujitsu RX100 S2 - page 264

    264 Appendi x ■ F or the United Kingdom Should the plug on t he flexible cord not be of the ty pe for your soc ket outlets, do not use an adapter but remove th e plug from the cord and discard. Caref ully prepare the en d of the su pply cord and fit a suitable plug.  The wires in this mains lead are colored in accordance with the following cod ...

  • Fujitsu RX100 S2 - page 265

    265 PRIMERGY RX100 S2 User ’s Guide Appendix A C R emote Contro l Function and Console R e direction When a persona l computer (PC ) is connecte d to the serial port of this ser ver with a cross cabl e, the server c an be turned on/of f or reset from the PC vi a RS-232C (remote con trol functi on). Consol e redirecti on can be perfor med in the s ...

  • Fujitsu RX100 S2 - page 266

    266 Appendi x C.2 Connecting the Server to a PC Connect the serve r to a PC using a cross c able.  In the BIOS Setup Utility , perform the following setting. • On the [Peripheral Configuration] submenu of the [Advanced] menu, change [Serial Multiplexer] to [BMC].  "8.2.6 Peripheral Configuration Submenu" (pg.200) C.3 Operating the ...

  • Fujitsu RX100 S2 - page 267

    267 PRIMERGY RX100 S2 User ’s Guide Appendix A 2 Enter the followin g command. Remote [Enter] The following message a ppears. 3 Enter the followin g command. Remote [Enter] The following menu ap pears. The "State" lin e in the message will show either of the following. 4 Use numeric keys to enter the des ired menu number . The table bel ...

  • Fujitsu RX100 S2 - page 268

    268 Appendi x C.4 Switching between Functions This section expla ins how to switching betwee n functions. ■ Switching from Console Re direction to the Remote Cont rol Functi on 1 In the ter minal software execu ting console r edirection, pr ess the [Esc] key and press the [S hift] + [8] keys. Console redirection switches to the re mote control fu ...

  • Fujitsu RX100 S2 - page 269

    269 PRIMERGY RX100 S2 User ’s Guide Appendix A D R ecy c ling This section explains how t o recycle this server . ■ Disposing of t he Server When scrapping this server , contact an office listed in the "Conta ct Information" of the "Start Guide". This server must be disposed of as industrial waste. Furthermore, if the server ...

  • Fujitsu RX100 S2 - page 270

    270 Appendi x ...

  • Fujitsu RX100 S2 - page 271

    271 PRIMERGY RX100 S2 User ’s Guide Inde x A Act ive Dire ctor y . . . . . . . . . . . . . . . . . . . . . 230 Adv anced Men u . . . . . . . . . . . . . . . . . . . . 199 Advanced System Configuration Subm enu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Application wizard Expe rt m ode . . . . . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 272

    272 H Hard dis k ac cess dis play LED . . . . . . . . . . . 23 High Reliab ility T ool . . . . . . . . . . . . . . . . . . . 1 9 How t o ins ta ll . . . . . . . . . . . . . . . . . . . . . 21 How t o Cr eate Dri ver Disk s . . . . . . . . . . . . 108 Hyper-threading functions . . . . . . . . . . . . . 205 I IDE cab le . . . . . . . . . . . . . . . ...

  • Fujitsu RX100 S2 - page 273

    273 PRIMERGY RX100 S2 User ’s Guide P Paging File Set ting For Win dows S erve r 20 03 . . . . . . . . . . 128 For W indows 2000 Server . . . . . . . . . . 133 Par allel A T A Sub menu . . . . . . . . . . . . . . . 195 Pas sword . . . . . . . . . . . . . . . . . . . . . . . . . 245 Changing/Delet ing . . . . . . . . . . . . . . . . 246 Set ting. ...

  • Fujitsu RX100 S2 - page 274

    274 T op Co ver . . . . . . . . . . . . . . . . . . . . . . . . . 164 Att ach ing . . . . . . . . . . . . . . . . . . . . . . . 165 Remo ving . . . . . . . . . . . . . . . . . . . . . . . 164 T rouble shoot ing . . . . . . . . . . . . . . . . . . . . . 221 T urning of f t he s erve r . . . . . . . . . . . . . . . . . . 31 T urning on the serv er . ...

  • Fujitsu RX100 S2 - page 275

    275 • The contents may be revi sed without prior notice. • Fujitsu assumes no liabili ty for damages to third party c opyrights or other rights arising from the use of any information in thi s manual. • No part of this manual may be reproduced in any without the prior written permission of Fujitsu. PRIMERGY RX100 S2 User's Guide B7FH-329 ...

Manufacturer Fujitsu Category Stereo System

Documents that we receive from a manufacturer of a Fujitsu RX100 S2 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- RX100 S2 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu RX100 S2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu RX100 S2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu RX100 S2, service manual, brief instructions and user manuals Fujitsu RX100 S2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu RX100 S2.

Similar manuals

A complete manual for the device Fujitsu RX100 S2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu RX100 S2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu RX100 S2.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu RX100 S2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu RX100 S2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu RX100 S2, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu RX100 S2 - which should help us in our first steps of using Fujitsu RX100 S2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu RX100 S2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu RX100 S2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu RX100 S2?

Use the form below

If you did not solve your problem by using a manual Fujitsu RX100 S2, ask a question using the form below. If a user had a similar problem with Fujitsu RX100 S2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)