English dropdown-ico

Manual Omega Engineering i.BTX-M

48 pages 0.88 mb
Download

Go to site of 48

Summary
  • Omega Engineering i.BTX-M - page 1

    USA MADE IN U ser ’ s Guide www .omega.com e-mail: info@omega.com For latest product manuals www .omegamanual.info ® ® Shop on line at Barometric Pressure + T emperature Pressure/T emp Main Menu http://192.168.1.200 Pressure/T emp (1 Hour/Div) 1 Day 1 Day 1 Week 1 Month 1 Y ear 1 Minute 1 Hour Mon Jul 24 09:42:10 PST 2006 32 9/Div 122 400 80/Di ...

  • Omega Engineering i.BTX-M - page 2

    It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply . OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct, but OM ...

  • Omega Engineering i.BTX-M - page 3

    T ABLE OF CONTENTS Part 1: Introduction 1.1 Safety and EMC Considerations ........................................................................ 2 1.2 Before Y ou Begin ................................................................................................ 2 1.3 Description ................................................................ ...

  • Omega Engineering i.BTX-M - page 4

    LIST OF FIGURES: Figure 1.1 iServer and iLD Big Display on the Ethernet Network ........................ 3 Figure 2.1 Mounting ................................................................................................ 4 Figure 2.2 DIP Switches ........................................................................................... 4 Figure ...

  • Omega Engineering i.BTX-M - page 5

    NO TES, WARNINGS and CA UTIONS Information that is especially important to note is identified by the following labels: • NOTE • W ARNING or CAUTION • IMPORT ANT • TIP NOTE: Provides you with information that is important to successfully setup and use the iServer . CAUTION: T ells you about the risk of electrical shock. CAUTION: Risk of dang ...

  • Omega Engineering i.BTX-M - page 6

    P ART 1 INTRODUCTION 1.1 Safety and EMC Considerations Refer to the CE Approvals Section. EMC Considerations • Whenever EMC is an issue, always use shielded cables. • Never run signal and power wires in the same conduit. • Use twisted-pair wires for signal connections. • Install Ferrite Bead(s) on signal wires close to the instrument if EMC ...

  • Omega Engineering i.BTX-M - page 7

    Award-winning T echnology . The iServer is simple to install and use. It features award winning technology that requires no special software except a Web browser . The iServer connects to an Ethernet Network with a standard RJ45 connector and sends data in standard TCP/IP packets. It is easily configured with a simple menu using a Web browser and c ...

  • Omega Engineering i.BTX-M - page 8

    4 P ART 2 HARDWARE 2.1 Mounting Position unit where required. Mark and drill holes as required. If unit is to be mounted on a flat surface, you may take the bottom rubber feet off the unit. It is recommended that you ground your unit by wrapping a wire around the mounting tab screw and tightening a lock washer so that it embeds itself into the meta ...

  • Omega Engineering i.BTX-M - page 9

    5 2.3 Parts of the iServer Unit Figure 2.3 Parts of the iServer Unit T able 2.1 Parts of iServer Unit ETHERNET RJ45 interface for 10BASE-T connection. iServer RESET Button: Used for power reseting the iServer board (Ethernet connection). FLASH RESET Button: Used for power reseting the Flash Memory Card/LCD board. ACTIVITY LED (Red) Blinking: Indica ...

  • Omega Engineering i.BTX-M - page 10

    6 2.4 Disassembly Instruction Y ou may need to open the unit for one of the following reasons: • T o wire relay connector . (Refer to Figure 2.7 ) • T o connect or replace the battery . • T o change S5 jumper . In the absence of AC power , and if S5 is installed, the LCD Backlight and iServer Board will be on and running on the battery power ...

  • Omega Engineering i.BTX-M - page 11

    7 2.5 Network Communication Interfaces 2.5.1 10Base-T RJ-45 Pinout The 10BASE-T Ethernet network (RJ45) system is used in the iServer for network connectivity . The 10 Mbps twisted-pair Ethernet system operates over two pairs of wires. One pair is used for receiving data signals and the other pair is used for transmitting data signals. This means t ...

  • Omega Engineering i.BTX-M - page 12

    8 P ART 3 NETWORK CONFIGURA TION 3.1 Network Protocols The iServer can be connected to the network using standard TCP/IP protocols. It also supports ARP , HTTP (WEB server), DHCP , DNS and T elnet protocols. 3.2 Ethernet (MAC) Address MAC (Media Access Control) address is your computer's unique hardware number . When you're connected to t ...

  • Omega Engineering i.BTX-M - page 13

    9 3.3 DHCP DHCP , Dynamic Host Configuration Protocol enables individual computers or devices to extract their IP configurations from a server (DHCP server). If the DHCP is enabled on your iServer , as soon as the iServer is connected to the network, there is an exchange of information between DHCP server and the iServer . During this process the I ...

  • Omega Engineering i.BTX-M - page 14

    3.5.1 Default IP Address The iServer is shipped with a default IP address set to 192.168.1.200 and Subnet Mask of 255.255.255.0 . If you are going to use a Web browser or T elnet program to access the iServer using its default IP address, make sure that the PC from which you’re establishing the connection has an IP address that is in the same ran ...

  • Omega Engineering i.BTX-M - page 15

    11 P ART 4 OPERA TIONS This iServer can be used and configured in several ways, depending on user ’s preference and network setup. It can be configured using a Web browser , like Netscape or Internet Explorer . It can also be configured using NEWPORT’s iCONNECT Configuration Software. If DHCP and DNS servers are used, the connection is very sim ...

  • Omega Engineering i.BTX-M - page 16

    12 4.1 iCONNECT Software The iServer may also be assigned an IP Address by using the iCONNECT software. a) Download the iCONNECT software from the website listed in this manual. b) Install iCONNECT software on a networked PC. This software is compatible with Windows 95, NT , 2000, and XP . c) Use iCONNECT to assign an IP address to the iServer and ...

  • Omega Engineering i.BTX-M - page 17

    13 4.2 Setting a New IP Address over the Network Besides using the iCONNECT software, you may use the iServer’s default IP address to access it and assign a new IP address to it. The iServer is shipped with a default IP address of 192.168.1.200 and Subnet Mask of 255.255.255.0 . Y ou can configure your PC’s Network connection with an IP address ...

  • Omega Engineering i.BTX-M - page 18

    14 4.3 Setup and Operation using the iServer Web Page • Start your web browser . • From the browser you type http://eisxxxx using the last four-digits from the MAC address label located on the device if DHCP and DNS are used. If a static IP address is used, then simply type http://x.x.x.x , where x.x.x.x is the iServer ’s IP address. • The ...

  • Omega Engineering i.BTX-M - page 19

    4.3.1 Read Sensor • Click on . In a few seconds the following page ( Figure 4.7 ) will appear with all default values of 100.00. Then the actual readings of T emperature and Barometric Pressure will be displayed. • This page automatically updates the T emperature and Barometric Pressure values. • Click on Main Menu to return to Home Page. Whi ...

  • Omega Engineering i.BTX-M - page 20

    16 4.3.1.2 Java Runtime Environment 1.5 (5.0) Setup instructions 1. Go to your computer's Control Panel. Open the Java Plug-in 2. Click on "Settings" & "View Applets" in the "General" tab. 3. Select the "Settings" button on the General T ab Un-check the "Enable Caching" box. Then close dial ...

  • Omega Engineering i.BTX-M - page 21

    17 4.3.2 Adjustable Chart • Click on , the following page ( Figure 4.8 ) should appear . The Java™ Applet graph displays T emperature and Barometric Pressure and can be charted across the full span (-40 to 123ºC) or within any narrow range (such as 20-30ºC). The time-base can display one minute, one hour , one day , one week, one month or one ...

  • Omega Engineering i.BTX-M - page 22

    4.3.3 Retrieving Data from Flash T o retrieve and graph the data that is stored in the Flash Memory , you have two options: OPTION 1: Y ou can use the iServer ’s WEB interface to chart the data stored in the flash memory . 1. Click on the “Chart” button located on the Server Home Page, see Figure 4.5 . 2. Select a time interval of Day , Week, ...

  • Omega Engineering i.BTX-M - page 23

    19 4.3.4 Access Control This section describes the "Access Control" page of the iServers’s Web interface. This page allows the users to set up the network and security parameters of the iServer . At the initial entrance to the “Access Control” page you will be prompted for the LOGIN Password (see Figure 4.6 ) prior to an ADMINISTRA ...

  • Omega Engineering i.BTX-M - page 24

    4.3.5 Configuration Setting up the Flash Memory Card can be done in the Configuration page. From the Home Page Menu click on to get to the page (see Figure 4.1 1 ). General Description of the Configuration page: There are two general sections “Flash Card Memory” and “Server”. Flash Card Memory consists of the following titles: Real T ime Cl ...

  • Omega Engineering i.BTX-M - page 25

    4.3.5 Configuration (continued) Figure 4.1 1 Configuration Below are the definitions of terms used in the Configuration page. A) Sensor/Device Setup Clicking on the No. 1 or 2 allows you to modify the Sensor/Device Parameters (see Section 4.3.6 for more details). http://192.168.1.200 Click on Device No. on the left to modify Sensor Parameters. Sens ...

  • Omega Engineering i.BTX-M - page 26

    B) Real Time Clock RTC Date and T ime : The formats are mm/dd/yyyy and hh:mm:ss . The exact formats are required otherwise an error message will appear in the T itle box. Note: time is military time/24 hour based. Adjust RTC Only : If checked, the clock will be updated and nothing else, provided that “ Activation ” is set to “ Status/RTC/Alar ...

  • Omega Engineering i.BTX-M - page 27

    F) Flash Recording T itle : Editable field with up to 16 characters long. The given name will display as a title on the Chart and Read Sensor pages either for the real-time data or the stored data. Sensor Unit: The unit of temperature either in degree Fahrenheit F or degree Celcius C f or each type of barometric pressure unit hPa, inHg or mmHg. . L ...

  • Omega Engineering i.BTX-M - page 28

    NOTE 2: Downloading data and recording can not be done at the same time. While downloading data, the writing process to the flash memory will be internally disabled while the data is being read from the memory flash. For small amounts of data to be retrieved (1 Day or 1 Week), this is not a significant interruption in the recording data. However , ...

  • Omega Engineering i.BTX-M - page 29

    Port: (default 2000) is the default TCP port number for the port to which the sensor is connected. Ports 1000 (used for HTTPget, refer to Section 4.5 ), 2002, 2003, and 2004 are reserved for internal use. T erminal Server usually describes a device that exchanges data between Ethernet/TCPIP networks and RS-232/RS-485 systems. With this iServer , th ...

  • Omega Engineering i.BTX-M - page 30

    26 4.3.6 Sensor Parameters • In the first column of Configuration page ( Figure 4.1 1 ), click on No. 1 to view and modify the Sensor Parameters page for T emperature. Figure 4.12 Sensor Parameters Below are some definitions of terms used in the Sensor Parameters page. Device Name: is a text field and can take up to 16 alphanumeric characters, it ...

  • Omega Engineering i.BTX-M - page 31

    27 4.4 T elnet Setup Set the Number of Connections to 1-5 other than 0, using telnet simulation program connect to iServer . In continuous mode, the telnet teminal will receive continuous messages from the iServer . In command mode, the command can be sent to query the iServer and get a response back. Refer to Figure 3.3 Send remote reset: T elnet ...

  • Omega Engineering i.BTX-M - page 32

    28 4.5.1 HTTPGET using Port 1000 Y ou can setup and read the information from the iServer by using the HTTPGET program. The following program can be used to read data from the embedded server firmware by using TCP port 1000 . The command string is sent to this TCP port, then the response can be read back from the same socket. The Httpget.exe file i ...

  • Omega Engineering i.BTX-M - page 33

    29 4.5.2 HTTPGET and ARP to setup Device IP Address Use the iCONNECT software, which may be downloaded from our website, to do these IP changes whenever possible. Use ARP first to assign the mac address to a static IP address in computer arp table by this command: apr –s 192.168.1.200 00-03-34-00-00-06-b6 Then use the following command to assign ...

  • Omega Engineering i.BTX-M - page 34

    30 4.6 ARP Protocol ARP is the Internet layer protocol responsible for matching or obtaining the MAC (hardware) address that corresponds to a particular IP address. The ARP command allows the user to view the current contents of the ARP cache of the local computer (residing on the same network). Microsoft includes the ARP .EXE utility for viewing a ...

  • Omega Engineering i.BTX-M - page 35

    4.7 iLOG Software The iLOG software can be used only with NEWPORT Electronics instruments. This is an Excel application software that can log temperature and barometric pressure from an iServer over the Ethernet or the internet. a) Download the iLOG software from the website listed in this manual. b) Install iLOG software on a networked PC. This so ...

  • Omega Engineering i.BTX-M - page 36

    4.8 Mail Notifier Software The Mail Notifier Software can be used only with NEWPORT Electronics instruments. For complete information of how to use the Mail Notifier software, click on the Help menu of the main window . The Mail Notifier software generates email notifications for alarm conditions. Users can be notified automatically of alarm condit ...

  • Omega Engineering i.BTX-M - page 37

    33 4.8.2 Program Options Setup and Configuration Complete program setup requires: • Entering a recipient for the email • Specifying connection details to MAPI services. • Defining alarms for devices, and selecting how and when the email will be active. Figure 4.17 iServer Mail Notifier Profile Setup The “Send T o” tab contains a field to ...

  • Omega Engineering i.BTX-M - page 38

    34 4.8.3 Device Setting and Configuration Device setup requires: • Entering the IP address for iServer device (for example 192.168.1.200 ). • Specifying Socket number (1000 or 2000 depending on iServer settings). • Defining RS485 Unit # interface address (1 to 199). Enter "0" for RS232 interface or for iServer . • Entering Reading ...

  • Omega Engineering i.BTX-M - page 39

    35 P ART 5 SPECIFICA TIONS SENSOR SPECIFICA TIONS BAROMETRIC PRESSURE (B) Accuracy/Range: ±2.0 mbar / 0-1 100 mbar (0-1 10 KPa) Resolution: 0.1 mbar TEMPERA TURE (T) Range*: 0°C to 70°C (32°F to 158°F) Accuracy*: ± 0.8°C @ 20°C (± 1.5°F @ 68°F) ± 2°C for -40 to 125°C (± 3.6°F for -40 to 257°F) *Note: extended temperature range is f ...

  • Omega Engineering i.BTX-M - page 40

    P ART 6 F ACT OR Y PRESET V ALUES PRESET P ARAMETERS F ACTOR Y DEF AUL TS Network Interface: IP Address 192.168.1.200 Gateway Address 0.0.0.0 Subnet Mask 255.255.255.0 Device Host Name eis and Last 4 digits from the MAC address Login Password 12345678 Admin Password 00000000 DHCP Disabled Flow Control None End Character 0D (Hex) (Carridge Return) T ...

  • Omega Engineering i.BTX-M - page 41

    APPENDIX A GLOSSAR Y User of this manual should be familiar with following definitions: ARP (Address Resolution Protocol) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address that is recognized in the local network. For example, the IP address in use today is an address that is 32-bits long. In an Ethern ...

  • Omega Engineering i.BTX-M - page 42

    Appendix B IP Address An IP address is a unique 32-bit address assigned to a computer and includes: • A network ID number identifying a network. • A host ID number identifying a computer on the network. All IP addresses have been divided into three smaller groups (classes) A, B and C • Class A addresses have 8-bits of network ID and 24-bits o ...

  • Omega Engineering i.BTX-M - page 43

    Appendix C IP Netmask IP Netmask or Subnet Mask is a 32-bit pattern of ones and zeros used to determine network portion of an IP address from the host portion of the IP address. Subnet mask is a network ID that is created by borrowing bits from host portion of IP address and using them as part of a network ID. The table below shows a default subnet ...

  • Omega Engineering i.BTX-M - page 44

    Appendix D ASCII Chart ASCII Dec Hex Binary ASCII Dec Hex Binary Char No Parity Char No parity NUL 00 00 00000000 @ 64 40 01000000 SOH 01 01 00000001 A 65 41 01000000 STX 02 02 00000010 B 66 42 01000010 ETX 03 03 0000001 1 C 67 43 0100001 1 EOT 04 04 00000100 D 68 44 01000100 ENQ 05 05 00000101 E 69 45 01000101 ACK 06 06 000001 10 F 70 46 010001 10 ...

  • Omega Engineering i.BTX-M - page 45

    Appendix D ASCII Chart Continuation / 47 2F 0010 1111 o 111 6 F 0 11 0 1111 0 48 30 001 10000 p 1 12 70 01 1 10000 1 49 31 001 10001 q 1 13 71 01 1 10001 2 50 32 001 10010 r 1 14 72 01 1 10010 3 51 33 001 1001 1 s 1 15 73 01 1 1001 1 4 52 34 001 10100 t 1 16 74 01 1 10100 5 53 35 001 10101 u 1 17 75 01 1 10101 6 54 36 001 101 10 v 1 18 76 01 1 101 ...

  • Omega Engineering i.BTX-M - page 46

    42 P ART 7 APPRO V ALS INFORMA TION 7.1 CE APPROV AL This product conforms to the EMC directive 89/336/EEC amended by 93/68/EEC, and with the European Low V oltage Directive 72/23/EEC. Electrical Safety EN61010-1:2001 Safety requirements for electrical equipment for measurement, control and laboratory . Basic Insulation Pollution Degree 2 Dielectri ...

  • Omega Engineering i.BTX-M - page 47

    WARRANTY / DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of one (1) year from the date of purchase. In addition to OMEGA ’s standard warranty period, OMEGA Engineering will extend the warranty period for one (1) additional year if the warranty card enclosed with each instrume ...

  • Omega Engineering i.BTX-M - page 48

    M4223/0806 W her e Do I Find Ev er ything I Need f or Pr ocess Measur ement and Contr ol? OM EGA…Of Cour se! Shop on line at omega.com TEMPERA TURE   Thermocouple, R TD & Thermistor Probes, Connectors, Panels & Assemblies   W ire: Thermocouple, R TD & Thermistor   Calibrators & Ice Point References   Record ...

Manufacturer Omega Engineering Category Marine Instruments

Documents that we receive from a manufacturer of a Omega Engineering i.BTX-M can be divided into several groups. They are, among others:
- Omega Engineering technical drawings
- i.BTX-M manuals
- Omega Engineering product data sheets
- information booklets
- or energy labels Omega Engineering i.BTX-M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Omega Engineering i.BTX-M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Omega Engineering i.BTX-M, service manual, brief instructions and user manuals Omega Engineering i.BTX-M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Omega Engineering i.BTX-M.

Similar manuals

A complete manual for the device Omega Engineering i.BTX-M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Omega Engineering i.BTX-M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Omega Engineering i.BTX-M.

A complete Omega Engineering manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Omega Engineering i.BTX-M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Omega Engineering i.BTX-M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Omega Engineering i.BTX-M, that we can find in the current document
3. Tips how to use the basic functions of the device Omega Engineering i.BTX-M - which should help us in our first steps of using Omega Engineering i.BTX-M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Omega Engineering i.BTX-M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Omega Engineering i.BTX-M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Omega Engineering i.BTX-M?

Use the form below

If you did not solve your problem by using a manual Omega Engineering i.BTX-M, ask a question using the form below. If a user had a similar problem with Omega Engineering i.BTX-M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)