Manual K2 Mounts K1-TS-S

20 pages 3.29 mb
Download

Go to site of 20

Summary
  • K2 Mounts K1-TS-S - page 1

    1 T able of Contents Before Y ou Begin 2 K1-F-S Installation 3 K1-TS-S & K1-A1-S Installation 6 K2-A1-S Installation 1 1 K1-UC-S (Under-Cabinet Mount) Installation 15 Specications 19 K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 1 ...

  • K2 Mounts K1-TS-S - page 2

    2 3 Before Y ou Begin STOP Do not attempt to install this product if you do not understand the instructions or if there are missing or defective parts. Improper installation may result in property damage or in personal injury . What Y ou Will Need: • Stud Finder • Phillips Screwdriver • Electric Drill • 1/8” Drill Bit • 9/16” Wrench ( ...

  • K2 Mounts K1-TS-S - page 3

    2 3 K1-F-S Installation Instructions Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. Attach the plate with the original screen screws. If they are not long ...

  • K2 Mounts K1-TS-S - page 4

    4 5 Attach the W all Plate to the W all ! Concrete anchors are not provided. T o mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury . 1. Locate a stud in ...

  • K2 Mounts K1-TS-S - page 5

    4 5 Attach the Screen to the W all Plate 1. Push the screen plate against the wall plate and then let it slide down into place. 2. Fasten the screw through the screw hole in the bottom of the bracket until it seats against the nut. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 5 ...

  • K2 Mounts K1-TS-S - page 6

    6 7 K1-TS-S & K1-A1-S Installation Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. Attach the plate with the original screen screws. If they are not lo ...

  • K2 Mounts K1-TS-S - page 7

    6 7 Attach the W all Plate to the W all ! Concrete anchors are not provided. T o mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury . 1. Locate a stud in ...

  • K2 Mounts K1-TS-S - page 8

    8 9 Assemble the Arm ( K1-A1-S only) 1. Assemble the arm, and attach it to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 8 ...

  • K2 Mounts K1-TS-S - page 9

    8 9 Attach the Screen to the W all Plate Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. The K1-TS-S is pictured to the right. The K1-A1-S is pictured on the next page. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 9 ...

  • K2 Mounts K1-TS-S - page 10

    10 1 1 K1-A1-S Attachment K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 10 ...

  • K2 Mounts K1-TS-S - page 11

    10 1 1 K2-A1-S Installation Instructions Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. Attach the plate with the original screen screws. If they are not ...

  • K2 Mounts K1-TS-S - page 12

    12 13 Attach the W all Plate to the W all ! Concrete anchors are not provided. T o mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury . 1. Locate a stud ...

  • K2 Mounts K1-TS-S - page 13

    12 13 Assemble the Arm 1. Assemble the arm, and attach it to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 13 ...

  • K2 Mounts K1-TS-S - page 14

    14 15 Attach the Screen to the Arm Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 14 ...

  • K2 Mounts K1-TS-S - page 15

    14 15 K1-UC-S (Under-Cabinet Mount) Installation Drill the Mounting Holes 1. Remove the contents of your cabinet. 2. Hold the bracket under the cabinet where it will be mounted. 3. Insert a pen or pencil through the mounting holes and make marks where you need to drill. 4. Remove the mount and use a 1/4” drill bit to drill holes up through the ca ...

  • K2 Mounts K1-TS-S - page 16

    16 17 Attach the Front Cap Piece 1. Slide the cap piece onto the bracket as shown. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 16 ...

  • K2 Mounts K1-TS-S - page 17

    16 17 Attach the Mount to the Cabinet 1. Insert four mounting screws down through the holes drilled earlier . 2. Place a spacer on each screw between the cabinet bottom and the top of the mount. 3. T ighten the screws down into the mount holes using the provided hex wrench. 4. Install a nut onto the end of each screw . K1 & K2 Series Manual 6.0 ...

  • K2 Mounts K1-TS-S - page 18

    18 19 Attach the Screen to the Mount ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen on the screen plate as shown. 2. Attach the plate with the original screen screws. If they are not long enough to securely mount the screen, ...

  • K2 Mounts K1-TS-S - page 19

    18 19 Specications ! Caution: These mounting brackets are intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in instability and cause injury . Model VESA Support T ilt Range Ext. from W all Max. Load Weight K1-F-S 60, 75 100mm 360 circle 1.75” 5 50 lbs K1-TS-S 60, 7 ...

  • K2 Mounts K1-TS-S - page 20

    20 K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 20 ...

Manufacturer K2 Mounts Category TV Mount

Documents that we receive from a manufacturer of a K2 Mounts K1-TS-S can be divided into several groups. They are, among others:
- K2 Mounts technical drawings
- K1-TS-S manuals
- K2 Mounts product data sheets
- information booklets
- or energy labels K2 Mounts K1-TS-S
All of them are important, but the most important information from the point of view of use of the device are in the user manual K2 Mounts K1-TS-S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals K2 Mounts K1-TS-S, service manual, brief instructions and user manuals K2 Mounts K1-TS-S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product K2 Mounts K1-TS-S.

Similar manuals

A complete manual for the device K2 Mounts K1-TS-S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use K2 Mounts K1-TS-S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of K2 Mounts K1-TS-S.

A complete K2 Mounts manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual K2 Mounts K1-TS-S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the K2 Mounts K1-TS-S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the K2 Mounts K1-TS-S, that we can find in the current document
3. Tips how to use the basic functions of the device K2 Mounts K1-TS-S - which should help us in our first steps of using K2 Mounts K1-TS-S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with K2 Mounts K1-TS-S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of K2 Mounts K1-TS-S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning K2 Mounts K1-TS-S?

Use the form below

If you did not solve your problem by using a manual K2 Mounts K1-TS-S, ask a question using the form below. If a user had a similar problem with K2 Mounts K1-TS-S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)