Manual RAD Data comm HCD-E1

232 pages 2.51 mb
Download

Go to site of 232

Summary
  • RAD Data comm HCD-E1 - page 1

    HCD-E1 HDSL CSU/DSU Installation and Operation Manual Notice This manual contains information that is proprietary to RAD Data Communications. No part of this publicatio n may be rep roduced in any for m whatsoever w ithout prio r written ap proval by RAD Data Communications. No representation or warranties for fitness for any purpose other than wha ...

  • RAD Data comm HCD-E1 - page 2

    ...

  • RAD Data comm HCD-E1 - page 3

    Warranty This RAD product is warranted against defects in material and workmanship for a period of one year from date of shipment. During the warranty period, RAD will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, this product must be returned to a service facility designated by RAD. ...

  • RAD Data comm HCD-E1 - page 4

    Telecommunication Safety The safety status of each of the ports on HCD-E1 are declared according to EN41003 and is detailed in the table below. Interconnection of these ports with other apparatus should be made such that the equipment continues to comply with clause 2.3 of EN60950 for SELV circuits after such a connection is made. Ports Safety Stat ...

  • RAD Data comm HCD-E1 - page 5

    Declaration of Conformity Manufacturer’s Name: RAD Data Communications Ltd. Manufacturer’s Address: 24 Raoul Wallenberg St. Tel Aviv 69719 Israel declares that the product: Product Name: HCD-E1 Conforms to the following standard(s) or other normative document(s): EMC: EN 55022 (1994) Limits and methods of measurement of radio disturbance charac ...

  • RAD Data comm HCD-E1 - page 6

    ...

  • RAD Data comm HCD-E1 - page 7

    Installing HCD-E1 1 Quick Start Guide Installation of HCD-E1 should be carried out only by an experienced technician. If you are familiar with RAD's HDSL modems, use this guide to prepare HCD-E1 for operation. 1. Installing HCD-E1 Switch and Jumper Settings HCD-E1 contains two sets of jumpers: • Main board internal jumpers and DIP switch • ...

  • RAD Data comm HCD-E1 - page 8

    Quick Start Guide HCD-E1 Installation & Operation Manual 2 Installing HCD-E1 7. Set the JP12 jumper to UNBAL E1. 8. Set the JP16 and JP17 jumpers to UNBAL. 9. Connect the JP9 jumper. 10. Install the JP8 and JP10 jumpers. 11. Reinstall the sublink interface board by reversing the procedure by which you removed it. Pay special attention to the fo ...

  • RAD Data comm HCD-E1 - page 9

    HCD-E1 Installation & Operation Manual Quick Start Guide 11/07/00 13:21 Configuring HCD-E1 3 2. Configuring HCD-E1 You can configure and operate HCD-E1 from either the front panel or a supervisory terminal. Note Some of the HCD-E1 configuration parameters depend on the type of remote unit being used. Therefore, after the HDSL synchronization is ...

  • RAD Data comm HCD-E1 - page 10

    Quick Start Guide HCD-E1 Installation & Operation Manual 4 Configuring HCD-E1 2. Connect the terminal to the CONTROL DCE port of HCD-E1. 3. Press <Enter> three times. 4. If the terminal displays the password prompt ( PASSWORD> ), enter the password. The default password is HCD . If the node number of HCD-E1 is a number other than zero, ...

  • RAD Data comm HCD-E1 - page 11

    HCD-E1 Installation & Operation Manual Quick Start Guide 11/07/00 13:21 Configuring HCD-E1 5 12. You can assign each HCD-E1 unit a logical name of up to eight characters. The logical name helps identify the source of alarm messages that HCD-E1 sends to the supervision terminal. Use the DEF NAME command to assign a logical name. 13. To reset HCD ...

  • RAD Data comm HCD-E1 - page 12

    Quick Start Guide HCD-E1 Installation & Operation Manual 6 Configuring HCD-E1 ...

  • RAD Data comm HCD-E1 - page 13

    HCD-E1 Installation & Operation Manual i Contents CHAPTER 1 INTRODUCTION 1.1 Overview ................................................................................................................... .... 1-1 General ........................................................................................................................ ...... ...

  • RAD Data comm HCD-E1 - page 14

    Table of Contents ii HCD-E1 Installation & Operation Manual 3.4 Configuration Parameters ............................................................................................... 3-7 3.5 Operating Instructions .................................................................................................. 3-1 9 Turning HCD-E1 On ....... ...

  • RAD Data comm HCD-E1 - page 15

    Table of Contents HCD-E1 Installation & Operation Manual iii DSP ALM REM.................................................................................................................... 4-31 DSP BERT CH .................................................................................................................... . 4-31 DSP HDR TST .... ...

  • RAD Data comm HCD-E1 - page 16

    Table of Contents iv HCD-E1 Installation & Operation Manual 5.5 Configuration Error Messages ....................................................................................... 5-31 5.6 Power-Up Self-Test ...................................................................................................... 5-3 4 5.7 Troubleshooting ........ ...

  • RAD Data comm HCD-E1 - page 17

    Table of Contents HCD-E1 Installation & Operation Manual v List of Figures Figure 1-1 Typical HCD-E1 Application ........................................................................................ 1 -2 Figure 1-2 HCD-E1 3D View ..................................................................................................... ... 1-6 Fig ...

  • RAD Data comm HCD-E1 - page 18

    Table of Contents vi HCD-E1 Installation & Operation Manual List of Tables Table 1-1 Automatically-Selected FIFO Size Values .................................................................... 1-16 Table 2-1 HCD-E1 Interface Adapter Cables ............................................................................... 2-11 Table 3-1 HCD-E1 Con ...

  • RAD Data comm HCD-E1 - page 19

    01/01/01 08:07 Overview 1-1 Chapter 1 Introduction 1.1 Overview General HCD-E1 is a standalone HDSL NTU (Network Terminal Unit) / LTU (Line Terminal Unit) that provides the user with one E1 sublink drop & insert port and two n × 64 kbps or n × 56 kbps data channels. Fractional E1 from the E1 sublink, as well as data from the n × 64 kbps / n ...

  • RAD Data comm HCD-E1 - page 20

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-2 Overview 01/01/01 08:07 When you order a unit with a V.35, V.36/RS-449, or X.21 interface, you receive a unit with the RS-530 interface provided with a corresponding adapter cable. HCD-E1 is available in the AC and DC versions. The AC version is powered by 100 to 240 VAC, 50 or ...

  • RAD Data comm HCD-E1 - page 21

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Overview 1-3 • Remote loopbacks on the data channel and E1 sublink of the local HCD-E1 • Remote loopbacks on the data channel and E1 sublink of the remote unit. • Inband-activated remote loopback on the data channel of remote HCD-E1 • H-RPT local loop (toward ...

  • RAD Data comm HCD-E1 - page 22

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-4 Physical Description 01/01/01 08:07 To expedite the routing, HCD-E1 supports two “bundle” routing modes, called “sequential bundle” and “alternate bundle” modes. In the sequential mode, one “bundle” (group of consecutive time slots, identified by the number of t ...

  • RAD Data comm HCD-E1 - page 23

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-5 Figure 1-2 HCD-E1 3D View Front Panel The front panel provides control over the unit operation. The LEDs provide real-time indications related to the operation and status of the unit. The LCD together with three push-button switches are use ...

  • RAD Data comm HCD-E1 - page 24

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-6 Functional Description 01/01/01 08:07 Each HCD-E1 data port supports the following control lines: • RTS - input from the locally connected data equipment • CTS - the user can permanently set the CTS line in the active state, or can make the CTS line follow the RTS line. • ...

  • RAD Data comm HCD-E1 - page 25

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-7 The transmission of data on each twisted-wire pair (HDSL line) is full duplex, and except for the distribution of payload data bits between the two lines, each HDSL line operates independently. HCD-E1 provides an embedded operations channel ...

  • RAD Data comm HCD-E1 - page 26

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-8 Functional Description 01/01/01 08:07 The remote management capabilities available through the serial RS-232 port are as follows: • Management by means of a Supervision Terminal • Management by means of Telnet • SNMP Management. If you have an H-RPT on your link, you can ...

  • RAD Data comm HCD-E1 - page 27

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-9 A basic management topology, which is suitable for both SNMP and Telnet management, is shown in Figure 1-3 . In this example, a network management station is attached to an Ethernet LAN. A remote access LAN extender, MBE/RAS/A, is located n ...

  • RAD Data comm HCD-E1 - page 28

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-10 Functional Description 01/01/01 08:07 Each SNMP agent recognizes the messages addressed to its own IP address. In addition, the SNMP agent includes a proprietary built-in IP router, which is able to route management messages in accordance with the network topology determined b ...

  • RAD Data comm HCD-E1 - page 29

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-11 For example, the following paths can be made available for the management traffic, when the management station is attached to HCD-E1: • The network is connected to the network management station using a single serial communication link, ...

  • RAD Data comm HCD-E1 - page 30

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-12 Functional Description 01/01/01 08:07 System Timing HCD-E1 offers selectable timing options, which enable the distribution of timing over the HDSL system, from the central office to the remote end. The use of stuffing on the HDSL subsystem ensures that the E1 signal and the da ...

  • RAD Data comm HCD-E1 - page 31

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-13 NETWORK SIDE E1 INTERFACE DATA EQUIPMENT DATA CHANNEL 2 INTERFACE DATA EQUIPMENT DATA CHANNEL 1 INTERFACE E1 INTERFACE CUSTOMER SIDE (DTE) DATA CHANNEL 2 INTERFACE DATA EQUIPMENT DATA CHANNEL 1 INTERFACE DATA EQUIPMENT HDSL LINE B INTERFAC ...

  • RAD Data comm HCD-E1 - page 32

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-14 Functional Description 01/01/01 08:07 Figure 1-7 Data Channel Timing, Flow of Timing Signals in a Typical Application In the application shown in Figure 1-7 , the data equipment located on the customer’s premises uses the HCD-E1 link to connect to a data network. Since data ...

  • RAD Data comm HCD-E1 - page 33

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-15 Table 1-1 Automatically-Selected FIFO Size Values Data Channel Rate FIFO Size 64 kbps ± 16 bits 128 and 192 kbps ± 30 bits 256 to 448 kbps ± 52 bits 512 to 1536 kbps ± 72 bits 1600 to 1792 kbps ± 52 bits 1856 and 1920 kbps ± 30 bits ...

  • RAD Data comm HCD-E1 - page 34

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-16 Functional Description 01/01/01 08:07 Figure 1-8 Sublink Timing, Flow of Timing Signals in a Typical Application Main Principles of Operation This section describes the E1 and the HDSL environments, to provide the background information required for the understanding of the co ...

  • RAD Data comm HCD-E1 - page 35

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-17 Time Slot 0 Time Slot 16 Time Slots 1-15, 17-31 FAS MAS a. Even Frames (0,2,4-14) b. ODD Frames (1,3,5-15) a. Frame 0 b. Frames 1-15 Channel Data 10011011 I 1 ANNNNN 0000X Y X X A B C D A B C D 12345678 32 Time Slots/Frame 8 Bits/ Time Slo ...

  • RAD Data comm HCD-E1 - page 36

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-18 Functional Description 01/01/01 08:07 − Bit 3 - this bit is used as a Remote Alarm Indication (RAI), to notify the equipment at the other end that the local equipment lost frame alignment, or does not receive an input signal. − The other bits, identified as S a4 through S ...

  • RAD Data comm HCD-E1 - page 37

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-19 At the receiving end, the checksum is calculated again on each submultiframe and then compared against the original checksum (sent by the transmitting end in the next submultiframe). The results are reported by two bits multiplexed in bit ...

  • RAD Data comm HCD-E1 - page 38

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-20 Functional Description 01/01/01 08:07 HDSL Environment Transmission Media HDSL systems are intended to operate on the local subscriber plant, which typically uses a mixture of unshielded twisted-wire pairs. Moreover, it is also necessary to tolerate bridged taps. HDSL systems ...

  • RAD Data comm HCD-E1 - page 39

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-21 By reducing the line symbol rate, the maximum range that can be reached is increased. Together with the advanced digital signal processing techniques implemented in HDSL systems, this results in a robust data transmission system that can r ...

  • RAD Data comm HCD-E1 - page 40

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-22 Functional Description 01/01/01 08:07 2048 kbps Data at the Application Frame Interface Time Slots Inserted in Core Frame with 2048 kbps Data HDSL Line 1 HDSL Line 2 TS0 0 TS0 TS0 1 TS0 TS0 TS1 TS1 2 TS2 TS2 3 TS1 TS2 TS3 TS3 4 TS4 TS4 5 TS3 TS4 TS5 TS5 6 TS6 TS6 7 TS5 TS6 TS7 ...

  • RAD Data comm HCD-E1 - page 41

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Functional Description 1-23 HDSL-Related System Functions The HDSL subsystem performs the following main functions: • Mapping of input data bits into HDSL frames, for transmission on the HDSL lines • Start-up process • Frame alignment • Loop identification an ...

  • RAD Data comm HCD-E1 - page 42

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-24 Technical Specifications 01/01/01 08:07 1.4 Technical Specifications HDSL Interface Compliance ETSI TR-152 Signal Format Dual duplex, 2B1Q line coding Line Baud Rate 584 kbaud (equivalent to 1168 kbps), for each pair Line Type Two unconditioned, unloaded twisted pairs Impedanc ...

  • RAD Data comm HCD-E1 - page 43

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Technical Specifications 1-25 Signal Levels Transmit Levels - Balanced interface: ± 3V ± 10% - Unbalanced interface: ± 2.37V ± 10% Receive LEVELS 0 to -10 dB Jitter Performance Per ITU G.823 Connectors - Balanced interface: 8-pin RJ-45 female connector - Unbalanc ...

  • RAD Data comm HCD-E1 - page 44

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-26 Technical Specifications 01/01/01 08:07 Diagnostics Loopbacks - HDSL main link local loopback, towards the E1 sublink and data channels of the local unit - Channel loopback on the local unit towards the DTE connected to the data channel of the remote unit (per channel) - Chann ...

  • RAD Data comm HCD-E1 - page 45

    HCD-E1 Installation & Operation Manual Chapter 1 - Introduction 01/01/01 08:07 Technical Specifications 1-27 E1 Sublink Receive Timing Always recovered from the E1 sublink receive data signal Transmit Timing (user-selectable) Follows the transmit timing of the HDSL link. Synchronous Data Channels - DCE timing mode: HCD-E1 data channel provides ...

  • RAD Data comm HCD-E1 - page 46

    Chapter 1 - Introduction HCD-E1 Installation & Operation Manual 1-28 Technical Specifications 01/01/01 08:07 Power AC Source 100 ÷ 240 VAC, 50 or 60 Hz DC Source -48 VDC (-36 VDC to -72 VDC) Environment Operating Temperature 0 ÷ 50 ° C (32 ÷ 122 ° F) Relative Humidity Up to 90%, non-condensing ...

  • RAD Data comm HCD-E1 - page 47

    11/12/00 10:36 Site Requirements and Prerequisites 2-1 Chapter 2 Installation and Setup This chapter describes installation procedures for the standalone HCD-E1 device. For instructions on installation of one or two units in a 19-inch rack, refer to the Rack Mounting Kit for 19-inch Racks guide that comes with the RM kit. After installing the unit: ...

  • RAD Data comm HCD-E1 - page 48

    Chapter 2 - Installation and Setup HCD-E1 Installation & Operation Manual 2-2 Installation and Setup 11/12/00 10:36 2.2 Package Contents The HCD-E1 package includes the following items: • HCD-E1 unit • HCD-E1 Installation and Operation Manual • AC power cord or DC power supply connector kit. • Interface adapter cable/s (interface orderi ...

  • RAD Data comm HCD-E1 - page 49

    HCD-E1 Installation & Operation Manual Chapter 2 - Installation and Setup 11/12/00 10:36 Installation and Setup 2-3 Jumper C/R Central Unit Remote Unit JP4 R J10 /C C R C R FG ND / GND ON OFF JP8 ON OFF No t Connected Connecte d FGND/GND ON SP ARE PA SSW D DEF SP DB INIT S1 Sublink Interface B oar d Data Channel 2 Interface B oar d RJ-45 Conn e ...

  • RAD Data comm HCD-E1 - page 50

    Chapter 2 - Installation and Setup HCD-E1 Installation & Operation Manual 2-4 Installation and Setup 11/12/00 10:36 Warning Access to the inside of the equipment is permitted only to authorized and qualified service personnel. To avoid accidental electric shock, always disconnect the interface cables and the power cord before removing the unit ...

  • RAD Data comm HCD-E1 - page 51

    HCD-E1 Installation & Operation Manual Chapter 2 - Installation and Setup 11/12/00 10:36 Installation and Setup 2-5 Co ve r Sc rew s (4 P laces) Co ve r Sc rew s (4 P laces) Figure 2-2 Identification of Cover Screws Setting the Main Board Internal Jumpers and Switches The internal jumpers and switches located on the HCD-E1 main board are identi ...

  • RAD Data comm HCD-E1 - page 52

    Chapter 2 - Installation and Setup HCD-E1 Installation & Operation Manual 2-6 Installation and Setup 11/12/00 10:36 • Switch section 3 – DEF SP. This section selects the source of the control port parameters: ON HCD-E1 uses the default parameters stored in its program EPROM. For the default values, see Table 3-4 in Chapter 3. OFF HCD-E1 use ...

  • RAD Data comm HCD-E1 - page 53

    HCD-E1 Installation & Operation Manual Chapter 2 - Installation and Setup 11/12/00 10:36 Installation and Setup 2-7 Warning Setting the FGND/GND jumper to OFF may make the equipment unsafe for direct connection to unprotected telecommunication networks at locations where constant excessive voltages may be present on the lines. Removing the E1 S ...

  • RAD Data comm HCD-E1 - page 54

    Chapter 2 - Installation and Setup HCD-E1 Installation & Operation Manual 2-8 Installation and Setup 11/12/00 10:36 Setting the Sublink Interface Board Jumpers Figure 2-4 shows the component side of the E1 sublink interface board, as seen after it is removed from the unit. Note The interface board has protection fuses for the surge protection c ...

  • RAD Data comm HCD-E1 - page 55

    HCD-E1 Installation & Operation Manual Chapter 2 - Installation and Setup 11/12/00 10:36 Installation and Setup 2-9 • For operation with the unbalanced interface: − Set the jumper JP12 to UNBAL E1. − Set the jumpers JP16 and JP17 to UNBAL. − Connect the jumper JP9. HCD-E1 is shipped with all the jumpers set for balanced interface. E1 Su ...

  • RAD Data comm HCD-E1 - page 56

    Chapter 2 - Installation and Setup HCD-E1 Installation & Operation Manual 2-10 Installation and Setup 11/12/00 10:36 Reinstalling the HCD-E1 Cover After completing the internal settings, reinstall the top cover as follows: 1. Position the lower half of the HCD-E1 case on a flat, clean surface. Check that the decorative black plastic strips on t ...

  • RAD Data comm HCD-E1 - page 57

    HCD-E1 Installation & Operation Manual Chapter 2 - Installation and Setup 11/12/00 10:36 Installation and Setup 2-11 Connecting the Data Channels HCD-E1 typically has two data ports, each terminated in a 25-pin D-type female connector. The units with an Ethernet interface arrive with the Ethernet interface module built in the upper port. For th ...

  • RAD Data comm HCD-E1 - page 58

    Chapter 2 - Installation and Setup HCD-E1 Installation & Operation Manual 2-12 Installation and Setup 11/12/00 10:36 Connecting the Control Port If you are using the control terminal, connect a cable prepared in accordance with Appendix B between the control port connector, designated CONTROL DCE (see Figure 3-1 in Chapter 3), and the control t ...

  • RAD Data comm HCD-E1 - page 59

    11/01/00 19:52 Front Panel Controls, Connectors, and Indicators 3-1 Chapter 3 Front Panel Operating Instructions 3.1 General This chapter contains detailed instructions for operating HCD-E1 from the front panel. The information presented in this chapter includes: • HCD-E1 front panel - Section 3.2 • General description of HCD-E1 control, displa ...

  • RAD Data comm HCD-E1 - page 60

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-2 Front Panel Controls, Connectors, and Indicators 11/01/00 19:52 10 8 E1 LOS LOC REM LINE A LINE B HDSL LOS ALM TS T CURSOR SCROLL ENTER DCE CONTROL HCD-E1 HCD-E1 HCD-E1 HCD-E1 3 2 1 5 6 7 9 11 4 Figure 3-1 HCD-E1 Front Panel Table 3-1 HCD-E1 Controls, Conn ...

  • RAD Data comm HCD-E1 - page 61

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Control of HCD-E1 Operation 3-3 3.3 Control of HCD-E1 Operation General The HCD-E1 operating mode is determined by a set of parameters stored in an internal non-volatile memory. To select these parameters, you can use the HCD-E1 front panel push ...

  • RAD Data comm HCD-E1 - page 62

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-4 Control of HCD-E1 Operation 11/01/00 19:52 FIRST ROW SECOND ROW ALARM BUFFER SCROLL CLEAR EMPTY SYSTEM PARAMETER CLK MASTER (onl y for the unit confi g ured as central) CLK_FBACK (onl y for the unit confi g ured as central) HCD TYPE CONFIG REM (onl y for t ...

  • RAD Data comm HCD-E1 - page 63

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Control of HCD-E1 Operation 3-5 Information Displayed on the LCD The LCD displays four types of information messages: • Status messages (alarms) • Diagnostics and performance monitoring data • Test status • Configuration parameters. Stat ...

  • RAD Data comm HCD-E1 - page 64

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-6 Control of HCD-E1 Operation 11/01/00 19:52 Configuration Parameters HCD-E1 configuration parameters are divided into the following seven groups: system parameters (SYSTEM PARAMETER), sublink parameters (SL PARAMETERS), channel parameters (CHANNEL PRM), con ...

  • RAD Data comm HCD-E1 - page 65

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Configuration Parameters 3-7 Additional Functions of ENTER The ENTER key has two additional functions: 1. When the LCD displays the ALARM BUFFER screen, the ENTER key can be used to delete all the alarm messages in the buffer. 2. When the LCD di ...

  • RAD Data comm HCD-E1 - page 66

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-8 Configuration Parameters Table 3-2 System Parameters Designation Function Values Configuration Guidelines CLK MASTER* Selects the master timing reference. INT Internal oscillator is selected SL Locked to the recovered receive clock of the E1 sublink. CH1 o ...

  • RAD Data comm HCD-E1 - page 67

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Configuration Parameters 3-9 Table 3-2 System Parameters (Cont.) Designation Function Values Configuration Guidelines CONFIG REM* Selects the ability to configure a remote unit YES Enables the downloading function. The configuration values selec ...

  • RAD Data comm HCD-E1 - page 68

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-10 Configuration Parameters Table 3-3 Sublink Configuration Parameters Designation Function Values Configuration Guidelines FRAME Selects the framing mode for the sublink UNFRAMED The E1 sublink transparently transfers the incoming data stream on a bit-by-bi ...

  • RAD Data comm HCD-E1 - page 69

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Configuration Parameters 3-11 Table 3-3 Sublink Configuration Parameters (Cont.) Designation Function Values Configuration Guidelines MAP MODE Determines the selection method for the E1 sublink time slots transferred to the HDSL link. Note : The ...

  • RAD Data comm HCD-E1 - page 70

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-12 Configuration Parameters Table 3-3 Sublink Configuration Parameters (Cont.) Designation Function Values Configuration Guidelines TS_0 to TS_31 (for UNFRAMED) TS_1 to TS_31 (for G732N) If you have selected USER under MAP, selects, for each HDSL time slot, ...

  • RAD Data comm HCD-E1 - page 71

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Configuration Parameters 3-13 Table 3-4 Control Port Parameters (Cont.) Designation Function Values Configuration Guidelines PARITY Selects the method of parity checking ODD Odd parity EVEN Even parity NONE Parity check disabled (available only ...

  • RAD Data comm HCD-E1 - page 72

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-14 Configuration Parameters Table 3-5 Channel Parameters Designation Function Values Configuration Guidelines FRAME Selects a framed or unframed mode of HDSL framer FRAMED HDSL framer is in the framed mode UNFRAMED Allows transfer of unframed 2048 kbps data ...

  • RAD Data comm HCD-E1 - page 73

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Configuration Parameters 3-15 Table 3-5 Channel Parameters (Cont.) Designation Function Values Configuration Guidelines START TS Selects the starting time slot for SEQ or ALT time slot allocation (not displayed for USER allocation) Any number in ...

  • RAD Data comm HCD-E1 - page 74

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-16 Configuration Parameters Table 3-5 Channel Parameters (Cont.) Designation Function Values Configuration Guidelines CLK MODE Selects the clocking mode of the given data channel. DCE The data channel p rovides both transmit and receive clocks to the user DT ...

  • RAD Data comm HCD-E1 - page 75

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Configuration Parameters 3-17 Table 3-6 BERT Parameters Designation Function Values Configuration Guidelines PATTERN Selects the test pattern. 2E3-1, 2E4-1, 2E5-1, 2E6-1, 2E7-1, 511, 2E10-1, 2047, 2E15-1, 2E17-1, 2E18-1, 2E20-1, QRSS, 2E21-1, 2E ...

  • RAD Data comm HCD-E1 - page 76

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-18 Configuration Parameters Table 3-7 Download Parameters Designation Function Values Configuration Guidelines SL MODE Selects the in-band transmission mode for the sublink NONE In-band SNMP and Telnet traffic is ignored TS0/F In-band SNMP and Telnet traffic ...

  • RAD Data comm HCD-E1 - page 77

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Operating Instructions 3-19 3.5 Operating Instructions This section covers the following activities: • Turning HCD-E1 on • Checking the HCD-E1 configuration • Normal HCD-E1 operating indications • Monitoring the HCD-E1 performance • Tu ...

  • RAD Data comm HCD-E1 - page 78

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-20 Operating Instructions 11/01/00 19:52 You can verify the HCD-E1 configuration as explained in the following section. If the configuration does not require modification, HCD-E1 is ready for operation immediately after the self-test is completed. For inform ...

  • RAD Data comm HCD-E1 - page 79

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Operating Instructions 3-21 Step Action Key Result 11 Bring the cursor to the right-hand field in the top row CURSOR 12 Scroll to display CH2 SCROLL The first row displays CHANNEL PRM CH2. 13 Repeat steps 7, 8 to see other Channel 2 parameters. ...

  • RAD Data comm HCD-E1 - page 80

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-22 Local Configuration Setup Procedure 11/01/00 19:52 Monitoring the HCD-E1 Performance HCD-E1 continuously measures diagnostics performance data. The diagnostics data is available under PORT DIAG or HDSL DIAG. For the explanation of the measured parameters, ...

  • RAD Data comm HCD-E1 - page 81

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Local Configuration Setup Procedure 3-23 Password Protection HCD-E1 has password protection designed to avoid undesirable modification of its parameters. You will be able to configure HCD-E1 from the front panel only if its password protection i ...

  • RAD Data comm HCD-E1 - page 82

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-24 Local Configuration Setup Procedure 11/01/00 19:52 To configure the unit, follow the steps below: Step Action Key Result 1 Bring the cursor to the top row (if not already there). CURSOR 2 Scroll to display the desired group of parameters in the top row. S ...

  • RAD Data comm HCD-E1 - page 83

    HCD-E1 Installation & Operation Manual Chapter 3 - Front Panel Operating Instructions 11/01/00 19:52 Local Configuration Setup Procedure 3-25 Working with Time Slots This section provides instructions for performing time slot configuration from the front panel. Reassigning All Time Slots between Data Channels/Sublink If you want to reassign all ...

  • RAD Data comm HCD-E1 - page 84

    Chapter 3 - Front Panel Operating Instructions HCD-E1 Installation & Operation Manual 3-26 Local Configuration Setup Procedure 11/01/00 19:52 3. To reassign closed time slots to a data channel, scroll to CHANNEL PRM CHX in the top row. Set the SPEED parameter to the corresponding (higher) value. For each time slot you want to reassign, scroll t ...

  • RAD Data comm HCD-E1 - page 85

    11/01/00 19:23 General 4-1 Chapter 4 Control from the Supervisory Port 4.1 General This chapter provides detailed instructions for the management of HCD-E1 by means of ASCII terminals and IP hosts using the Telnet protocol. The initial configuring of HCD-E1 is to be performed using a standard ASCII terminal connected to the HCD-E1 control port, CON ...

  • RAD Data comm HCD-E1 - page 86

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-2 Hardware Requirements 11/01/00 19:23 4.2 Hardware Requirements Terminal Characteristics Any standard ASCII terminal (“dumb” terminal or personal computer emulating an ASCII terminal) equipped with a V.24/RS-232 communication interface can be used to con ...

  • RAD Data comm HCD-E1 - page 87

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 Hardware Requirements 4-3 For multidrop operation, each HCD-E1 can be assigned a node number in the range of 1 through 255. Assigning node number 0 to the HCD-E1 means that it will accept and answer any message: this is not permitted in multidrop ...

  • RAD Data comm HCD-E1 - page 88

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-4 Hardware Requirements 11/01/00 19:23 Request to Send (RTS) The RTS line is normally ON (active) when the supervision terminal is in session. When the RTS line is OFF (inactive), HCD-E1 interprets any data received from the terminal on the TD line as MARK. C ...

  • RAD Data comm HCD-E1 - page 89

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 Starting a Supervision Terminal Management Session 4-5 AUTOBAUD Function When the AUTOBAUD function is enabled, HCD-E1 can identify the operating data rate of the terminal by analyzing the timing of three consecutive Carriage Return + Line Feed c ...

  • RAD Data comm HCD-E1 - page 90

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-6 Starting a Supervision Terminal Management Session 11/01/00 19:23 1. If you don’t know the node number, go to step 2. If you know the node number, enter it followed by the command (see General Guidelines and Principles below). If there is still no respons ...

  • RAD Data comm HCD-E1 - page 91

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Control Language 4-7 4. To close a data channel, use the DEF CH X command and set the SPEED parameter to NC. 5. To close the sublink, use the DEF SL command and set the NUM_OF_TS parameter to NC. 6. To reassign the closed time slots to the ...

  • RAD Data comm HCD-E1 - page 92

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-8 HCD-E1 Control Language 11/01/00 19:23 • Commands can be entered only when the HCD-E1 control port working prompt is displayed. The prompt is HCD> , and it always appears at the beginning of a new line. The cursor appears to the right of the prompt. ? ...

  • RAD Data comm HCD-E1 - page 93

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Control Language 4-9 • In case a command is invalid, HCD-E1 does not execute it and displays the following: - ‘Bad command or parameter. Type 'h' for help’ if the command syntax is wrong - An appropriate error message (see ...

  • RAD Data comm HCD-E1 - page 94

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-10 HCD-E1 Control Language 11/01/00 19:23 Table 4-1 HCD-E1 Command Set Index (Cont.) Command Purpose Options CLR ALM HRPT Clear the ON-type alarms stored in the H-RPT alarm buffer /A CLR LOOP BERT CH X, or CLR LP BERT CH X* CLR LOOP INBAND CH X, or CLR LP INB ...

  • RAD Data comm HCD-E1 - page 95

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Control Language 4-11 Table 4-1 HCD-E1 Command Set Index (Cont.) Command Purpose Options DEF PWD Define a password DEF SL Define E1 sublink parameters DEF SP Define control port parameters DEF SYS Define system parameters DEF TERM Reset th ...

  • RAD Data comm HCD-E1 - page 96

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-12 HCD-E1 Control Language 11/01/00 19:23 Table 4-1 HCD-E1 Command Set Index (Cont.) Command Purpose Options DSP ST SL Display status information on the E1 sublink, and the contents of the sublink BPV counters (when CRC-4 function is off), and optionally clea ...

  • RAD Data comm HCD-E1 - page 97

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-13 4.5 HCD-E1 Command Set Description This section describes the HCD-E1 commands. The commands are listed in alphabetical order. The description includes command format, use, and options. The following notational ...

  • RAD Data comm HCD-E1 - page 98

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-14 HCD-E1 Command Set Description 11/01/00 19:23 CLR ALM REM Purpose Clear the remote unit alarm buffer. Syntax CLR ALM REM [/A] Use • To clear only alarms of the ON type stored in the alarm buffer of the remote unit (see Table 5-1 ), type: CLR ALM REM<C ...

  • RAD Data comm HCD-E1 - page 99

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-15 CLR LOOP Purpose Deactivate the specified user-initiated loopback or test. Syntax CLR LOOP [loop type], or CLR LP [loop type] Use • To deactivate a local (L) loopback on the HDSL lines, type: CLR LOOP L LINE& ...

  • RAD Data comm HCD-E1 - page 100

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-16 HCD-E1 Command Set Description 11/01/00 19:23 CLR TST Purpose Deactivate all the user-initiated tests and loopbacks being activated from this unit. Syntax CLR TST Use To deactivate all the user-initiated tests and loopbacks, type: CLR TST<CR> HCD-E1 ...

  • RAD Data comm HCD-E1 - page 101

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-17 A typical display, as seen after all the parameters are selected, is shown below: DAY = 01 MONTH = 03 YEAR [4 CHARS] = 1996 WEEK DAY =FRI Below HCD-E1 displays the date and time (note that the date has changed) ...

  • RAD Data comm HCD-E1 - page 102

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-18 HCD-E1 Command Set Description 11/01/00 19:23 Display Fields The agent parameters displayed on the data form, their range of values and description of how to change them are as follows: TELNET_APATHY_TIME Press the F or B keys to select the time, in minute ...

  • RAD Data comm HCD-E1 - page 103

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-19 HCD-E1 displays the BERT parameters data form: PATTERN ERROR_INJECTION_RATE RX_INBAND 2E3-1 NO ERR DISABLE The functions of the fields are as follows: PATTERN Sel ec ts t he tes t p att er n. Th e av ail able s ...

  • RAD Data comm HCD-E1 - page 104

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-20 HCD-E1 Command Set Description 11/01/00 19:23 FRAME_MODE MULTIPLIER MAP_TYPE SPEED START_TS CTS FIFO_SIZE FRAMED 64 USER NC N/A ON AUTO 2. Change the desired parameters (using spacebar to move between them and pressing F or B to increase or decrease their ...

  • RAD Data comm HCD-E1 - page 105

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-21 Designation Function Values START_TS Selects the starting time slot for SEQ or ALT time slot allocation Any number in the range of 0 to 31, consistent with the desired number of user time slots. The sum of the ...

  • RAD Data comm HCD-E1 - page 106

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-22 HCD-E1 Command Set Description 11/01/00 19:23 5. After completing the first line, press <CR> to move to the next line. Repeat the procedure until all the time slots are defined. When done, press <CR> to finish. HCD-E1 displays the date and time ...

  • RAD Data comm HCD-E1 - page 107

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-23 DEF NAME Purpose Define the logical name (up to eight alphanumeric characters). Syntax DEF NAME Use 1. To define the HCD-E1 logical name, type: DEF NAME<CR> HCD-E1 displays the logical name entry form: EN ...

  • RAD Data comm HCD-E1 - page 108

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-24 HCD-E1 Command Set Description 11/01/00 19:23 DEF PB Purpose Define each time slot priority (high or low). In case one of the HDSL lines is down, time slots with high priority will still continue to be sent on the remaining line. Syntax DEF PB Use 1. Type: ...

  • RAD Data comm HCD-E1 - page 109

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-25 2. Type the required password. Carefully check that the specified password has been indeed typed in, and then press <CR>. HCD-E1 displays the next line: CURRENT PASSWORD = 'password' where &apos ...

  • RAD Data comm HCD-E1 - page 110

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-26 HCD-E1 Command Set Description 11/01/00 19:23 6. When done, press <CR> to finish. HCD-E1 displays the date and time followed by the HCD-E1 prompt. Note 1. You will have to perform steps 3 and 4 only in the case you have selected USER in the MAP_TYPE ...

  • RAD Data comm HCD-E1 - page 111

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-27 PWD Password protection: YES Password protection is enabled. NO Password protection is disabled. LOG_OFF Idle disconnect time: NO Automatic session disconnection disabled. 10_MIN Automatic disconnection after t ...

  • RAD Data comm HCD-E1 - page 112

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-28 HCD-E1 Command Set Description 11/01/00 19:23 DEF SYS Purpose Assign values to system parameters. Syntax DEF SYS Use 1. Type: DEF SYS<CR> HCD-E1 displays the system parameters data form, which presents the current parameter values as defaults. A typi ...

  • RAD Data comm HCD-E1 - page 113

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-29 The codes used by the supported terminals are listed in the following table: Function Terminal Type TV920 VT52 VT100 Freedom100 Freedom220 Clear Screen 1B2A0000 N/A 1B5B324A 1B2A0000 1B5B324A Cursor Home 1E0000 ...

  • RAD Data comm HCD-E1 - page 114

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-30 HCD-E1 Command Set Description 11/01/00 19:23 Display Format The contents of the alarm buffer are displayed as a table with four columns: alarm number, alarm syntax (description), alarm state, and date & time of alarm occurrence. Each block of alarms r ...

  • RAD Data comm HCD-E1 - page 115

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-31 DSP ALM REM Purpose Display the contents of the alarm buffer of the appliance located at the remote end of the HDSL link. This buffer can contain up to 100 alarms. Syntax DSP ALM REM[Option] Use • To display ...

  • RAD Data comm HCD-E1 - page 116

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-32 HCD-E1 Command Set Description 11/01/00 19:23 • To display the current results of a BER test and then reset the error count, type: DSP BERT CH 1 /C<CR> or DSP BERT CH 2 /C<CR> • • • • To monitor the results of a BERT test, type: DSP B ...

  • RAD Data comm HCD-E1 - page 117

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-33 The results are presented in the following format: ERROR_BITS RUN_ TIME (SEC) ERRORS (SEC) SYNC_ LOSS (SEC) ERROR_INJECT 0 100 0 0 OFF The display fields are as follows: ERROR_BITS Total number of bit errors de ...

  • RAD Data comm HCD-E1 - page 118

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-34 HCD-E1 Command Set Description 11/01/00 19:23 DSP HDSL PM Purpose Display the contents of performance monitoring registers of a selected HDSL line of the local HCD-E1. For an explanation of the HDSL performance monitoring registers, refer to Section 5-3. S ...

  • RAD Data comm HCD-E1 - page 119

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-35 INTERVAL 01 ES = 000 UAS = 000 SES = 000 BBE = 000 ESR = 00.00% SESR = 00.00% BBER = 00.00% INTERVAL 02 ES = 000 UAS = 000 SES = 000 BBE = 000 ESR = 00.00% SESR = 00.00% BBER = 00.00% INTERVAL 03 ES = 000 UAS = ...

  • RAD Data comm HCD-E1 - page 120

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-36 HCD-E1 Command Set Description 11/01/00 19:23 DSP R HDR TST Purpose Display the results of the last hardware test performed by the unit located at the remote end of the HDSL link (during power-on self-test or regular operation). Syntax DSP R HDR TST Use ? ...

  • RAD Data comm HCD-E1 - page 121

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-37 • To display current values of the performance monitoring registers of the HDSL line 1, and then clear all these registers and restart the count intervals, type: DSP R HDSL PM LP1/CA<CR> or DSP R HDSL P ...

  • RAD Data comm HCD-E1 - page 122

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-38 HCD-E1 Command Set Description 11/01/00 19:23 Note In case the CRC-4 function is disabled, HCD-E1 displays an error message: ILLEGAL COMMAND FOR CURRENT MODE. If the CRC-4 function is enabled on the sublink of the local unit, but disabled at the remote end ...

  • RAD Data comm HCD-E1 - page 123

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-39 The distance is assigned as follows: • Each segment between two IP routers is assigned a weight of 6. For example, when the path to an agent passes two HCD-E1 with their SNMP management enabled, the distance ...

  • RAD Data comm HCD-E1 - page 124

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-40 HCD-E1 Command Set Description 11/01/00 19:23 PM OF PORT - A CRC ERROR EVENTS = 0 CRC AVG ERR EVENTS = 0 CURRENT ES = 0 CURRENT UAS = 0 CURRENT SES = 0 CURRENT BES = 0 CURRENT LOFC = 0 CURRENT CSS = 0 CURRENT TIMER = 176 For the description and allowed ran ...

  • RAD Data comm HCD-E1 - page 125

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-41 Use • To display the status information for a selected channel, type: DSP ST CH 1<CR> or DSP ST CH 2<CR> A typical channel status display is shown below: STATUS OF CH -1 INTERFACE = RS530 LOOPS TY ...

  • RAD Data comm HCD-E1 - page 126

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-42 HCD-E1 Command Set Description 11/01/00 19:23 DSP ST LINE Purpose Display status information on the HDSL lines. Syntax DSP ST LINE [Option] Use • To display the current status information for HDSL line 1, type: DSP ST LINE 1<CR> or DSP ST LINE<C ...

  • RAD Data comm HCD-E1 - page 127

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-43 The fields included in the status information display are listed below: LINE LOOP Displays the state of the local line loop on the corresponding HDSL line. NO Local line loop is not activated YES Local line loo ...

  • RAD Data comm HCD-E1 - page 128

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-44 HCD-E1 Command Set Description 11/01/00 19:23 Display Format A typical sublink status display is shown below. STATUS OF PORT TYPE = E1 FUNCTION = DSU ALARMS = L. SYNC LOSS ============ R. SYNC LOSS ============ OFF OFF LOOPS = REM PORT ======== REM REM POR ...

  • RAD Data comm HCD-E1 - page 129

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-45 Use • To view the current system status, type: DSP ST SYS<CR> HCD-E1 performs the command and displays the date and the time followed by the HCD-E1 prompt. Display Format A typical status information di ...

  • RAD Data comm HCD-E1 - page 130

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-46 HCD-E1 Command Set Description 11/01/00 19:23 HRPT Indicates whether there is an H-RPT repeater on the HDSL link, and the side of H-RPT to which your HCD-E1 is connected. DOESN’T EXIST There is no H-RPT on the HDSL link. NTU_SIDE Your HCD-E1 is configure ...

  • RAD Data comm HCD-E1 - page 131

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-47 Following is a list of fields appearing in the time slot display: TS Indicates the main link time slot number 0 through 31 TYPE Indicates the type of time slot assignment: NC time slot not assigned CH1 time slo ...

  • RAD Data comm HCD-E1 - page 132

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-48 HCD-E1 Command Set Description 11/01/00 19:23 Syntax F Use 1. To display the current codes, type: F<CR> The terminal function entry screen is displayed. The screen includes three separate lines, displayed one after the other. A typical screen, showin ...

  • RAD Data comm HCD-E1 - page 133

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-49 INIT DB Purpose Erase the user-defined configuration from the database and load the database with a specified set of default parameters values ( see Table 4-2) . Syntax INIT DB Use Type: INIT DB<CR> This ...

  • RAD Data comm HCD-E1 - page 134

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-50 HCD-E1 Command Set Description 11/01/00 19:23 Table 4-2 HCD-E1 Default Configuration (Cont.) Parameter Type Parameter Designation Default Value BERT PATTERN ERROR_INJECTION_RATE RX_INBAND 2E3-1 NO ERR DISABLE DOWNLOAD ML_DL_MODE SL_DL_MODE NONE NONE INIT F ...

  • RAD Data comm HCD-E1 - page 135

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 HCD-E1 Command Set Description 4-51 To activate Type BERT test on data channel X of HCD-E1 In-band loopback on data channel X of the remote unit Local (L) loopback on the HDSL lines (only from the unit configured as central) Local (L) loopback on ...

  • RAD Data comm HCD-E1 - page 136

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-52 Supervision Terminal Operating Instructions 11/01/00 19:23 TIME Purpose Set the time for the HCD-E1 internal real-time clock. Syntax TIME Use 1. Type: TIME<CR> HCD-E1 sends the entry line for the first parameter: HOUR = 12 2. If you do not want to ch ...

  • RAD Data comm HCD-E1 - page 137

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 Supervision Terminal Operating Instructions 4-53 1. Press the <CR> key three times. When HCD-E1 has successfully identified the data rate of the supervision terminal, it notifies you of the results of its power-up self-test: HCD Self Test i ...

  • RAD Data comm HCD-E1 - page 138

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-54 Supervision Terminal Operating Instructions 11/01/00 19:23 To establish a session with a specific HCD-E1, use the following procedure: 1. Press the <CR> key three times. 2. Type NODE, space, the desired HCD-E1 node number, another space, and then typ ...

  • RAD Data comm HCD-E1 - page 139

    HCD-E1 Installation & Operation Manual Chapter 4 - Control from the Supervisory Port 11/01/00 19:23 Supervision Terminal Operating Instructions 4-55 If your command is not correct, HCD-E1 does not execute it and displays the following: - ‘Bad command or parameter. Type 'H' for help’ if the command syntax is wrong - An appropriate ...

  • RAD Data comm HCD-E1 - page 140

    Chapter 4 - Control from the Supervisory Port HCD-E1 Installation & Operation Manual 4-56 Supervision Terminal Operating Instructions 11/01/00 19:23 ...

  • RAD Data comm HCD-E1 - page 141

    01/01/01 08:15 Status Indications and Alarms 5-1 Chapter 5 Troubleshooting and Diagnostics 5.1 General This chapter describes the HCD-E1 diagnostics functions, which include: • Status indications and alarms - Section 5.2 • Performance diagnostics - Section 5.3 • Diagnostic loopbacks - Section 5.4 • Configuration error messages - Section 5.5 ...

  • RAD Data comm HCD-E1 - page 142

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-2 Status Indications and Alarms 01/01/01 08:15 When an ON/OFF-type alarm changes its state from ON to OFF, it is not removed from the alarm buffer. Moreover, a new entry of this alarm is added to the alarm buffer. This feature enables you to see the alarm histo ...

  • RAD Data comm HCD-E1 - page 143

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Status Indications and Alarms 5-3 Table 5-1 HCD-E1 Alarm Buffer Messages LCD Message Terminal Message Alarm Number Probable Cause Corrective Actions Alarm Type AIS OCCURR: SL* AIS OCCURRED: SL* 12 AIS is being detected on the E1 sublink. Check the ...

  • RAD Data comm HCD-E1 - page 144

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-4 Status Indications and Alarms 01/01/01 08:15 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Probable Cause Corrective Actions Alarm Type DB-INIT DW IS ON DB-INIT SWITCH IS ON 21 Section DB INIT is set to ON. This mess ...

  • RAD Data comm HCD-E1 - page 145

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Status Indications and Alarms 5-5 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Probable Cause Corrective Actions Alarm Type DTE NOT CON CH:1 DTE NOT CONNECTED TO CH:1 38 The Ethernet interface is not conn ...

  • RAD Data comm HCD-E1 - page 146

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-6 Status Indications and Alarms 01/01/01 08:15 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Cause Corrective Actions Alarm Type FALLBACK CLK USE* CLOCK WAS CHANGED TO FALLBACK* 47 HCD-E1 switched to the fallback clock ...

  • RAD Data comm HCD-E1 - page 147

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Status Indications and Alarms 5-7 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Cause Corrective Actions Alarm Type L. SYNC LOSS: SL* LOCAL SYNC LOSS: SL* 14 Local loss of frame synchronization alarm on th ...

  • RAD Data comm HCD-E1 - page 148

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-8 Status Indications and Alarms 01/01/01 08:15 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Cause Corrective Actions Alarm Type PSWRD DW IS ON PSWRD SWITCH IS ON 19 Section PASSWD is set to ON. This message appears on ...

  • RAD Data comm HCD-E1 - page 149

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Status Indications and Alarms 5-9 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Cause Corrective Actions Alarm Type R. SYNC LOSS: SL REMOTE SYNC LOSS: SL 23 The equipment connected to the E1 sublink report ...

  • RAD Data comm HCD-E1 - page 150

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-10 Status Indications and Alarms 01/01/01 08:15 Table 5-1 HCD-E1 Alarm Buffer Messages (Cont.) LCD Message Terminal Message Alarm Number Cause Corrective Actions Alarm Type SYNC LOSS:LP1* SYNC LOSS:LP2* SYNC LOSS:LP1* SYNC LOSS:LP2* 26 Loss of synchronization o ...

  • RAD Data comm HCD-E1 - page 151

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Status Indications and Alarms 5-11 Table 5-2 HCD-E1 Alarm Buffer Messages (Cont.) Alarm Message Alarm Number Cause Corrective Actions Alarm Type HRPT_NTU SYNC LOSS:LP1 HRPT_NTU SYNC LOSS:LP2 04 Loss of synchronization on the specified HDSL line at ...

  • RAD Data comm HCD-E1 - page 152

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-12 Status Indications and Alarms 01/01/01 08:15 Working with Alarm Buffer You can manage the alarm buffer either from the control terminal, or from the LCD. From the Control Terminal To display the active alarms from the control terminal, type DSP ALM. The term ...

  • RAD Data comm HCD-E1 - page 153

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Performance Diagnostics Data 5-13 5.3 Performance Diagnostics Data General HCD-E1 has two capabilities for collection of performance statistics: E1 and HDSL performance monitoring capability. This section first describes the principles and paramete ...

  • RAD Data comm HCD-E1 - page 154

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-14 Performance Diagnostics Data 01/01/01 08:15 • • • • Current errored seconds (CURR ES) An errored second is any second containing one or more CRC error events, or one or more OOF events, or one or more controlled slip events. The data is collected for ...

  • RAD Data comm HCD-E1 - page 155

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Performance Diagnostics Data 5-15 • • • • Long-term bursty errored seconds (L.TERM BES) The total number of BES in the current 24-hour interval. • • • • Long-term loss of frame counter (L.TERM LOFC) The total number of LOF events in ...

  • RAD Data comm HCD-E1 - page 156

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-16 Performance Diagnostics Data 01/01/01 08:15 Summary of E1 Performance Monitoring Table 5-3 gives a summary of the performance diagnostics data displayed under the header PORT DIAGNOSTICS on the HCD-E1 front panel. Table 5-3 Summary of E1 Performance Monitori ...

  • RAD Data comm HCD-E1 - page 157

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Performance Diagnostics Data 5-17 Table 5-3 Summary of E1 Performance Monitoring (Cont.) Display Description Range LST DEG MIN Last 24-hour count of degraded minutes. The display is updated every 24 hours. 0 - 1440 BPV COUNT The total number of BPV ...

  • RAD Data comm HCD-E1 - page 158

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-18 Performance Diagnostics Data 01/01/01 08:15 • • • • Background block error ratio (BBER) The ratio of BBE to the total seconds in the current 15-minute interval (not displayed on the LCD). • • • • Current seconds (SECS) The number of seconds i ...

  • RAD Data comm HCD-E1 - page 159

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Performance Diagnostics Data 5-19 Displaying the Performance Data on the Front-Panel LCD To display the E1 and HDSL performance diagnostics data on the HCD-E1 front-panel LCD, use the following procedure: Step Action Key Result 1 Bring the cursor t ...

  • RAD Data comm HCD-E1 - page 160

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-20 Performance Diagnostics Data 01/01/01 08:15 Resetting the Performance Data Registers The registers storing diagnostics data can be reset. To reset a register, bring the register to display and press ENTER. To ensure that the collected data remains meaningful ...

  • RAD Data comm HCD-E1 - page 161

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Diagnostic Tests 5-21 5.4 Diagnostic Tests Diagnostic Loopbacks The user-controlled test functions of HCD-E1 consist of the following diagnostic loopback tests: Loopback Description Terminal Command Designation on the LCD Second Row Top Row (Right) ...

  • RAD Data comm HCD-E1 - page 162

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-22 Diagnostic Tests 01/01/01 08:15 LP L LINE These local loopbacks on the HDSL lines are performed in the HDSL framer, as shown in Figure 5-1 . Test signal is provided either by the equipment connected to one of the inputs, which must receive its own transmissi ...

  • RAD Data comm HCD-E1 - page 163

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Diagnostic Tests 5-23 LP L SL This local loopback towards the E1 sublink of the local HCD-E1 is performed by connecting the E1 sublink input signal (input to HCD-E1) to the output of the sublink from HCD-E1, as shown in Figure 5-3 . The test signal ...

  • RAD Data comm HCD-E1 - page 164

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-24 Diagnostic Tests 01/01/01 08:15 During the loopback, the DTE connected to the E1 sublink of the local HCD-E1, continues to receive data. LP R R SL This remote remote loopback towards the DTE connected to the E1 sublink of the local HCD-E1 is performed by con ...

  • RAD Data comm HCD-E1 - page 165

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Diagnostic Tests 5-25 Figure 5-6 LP L CH 1 Loopback LP R CH X This remote loopback towards the DTE connected to data channel X of the remote HCD-E1 (X can be one or two) is performed by connecting the local data channel receive signal to its transm ...

  • RAD Data comm HCD-E1 - page 166

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-26 Diagnostic Tests 01/01/01 08:15 This test checks the connections to the DTE connected to the data channel of the local HCD-E1, all the circuits of the remote unit, the functions of the remote unit and local HCD-E1, and the transmission path connecting the tw ...

  • RAD Data comm HCD-E1 - page 167

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Diagnostic Tests 5-27 CH2 CH1 LOCAL HC D-E1 REMOT E UNIT E1 Inte rface Data Interface HDSL Li ne A Interface HDSL Line A HDSL Line B Processing HDSL Li ne A Interface Processing Da ta Interface HDSL Li ne B Interface HDSL Li ne B Interface E1 Tx Tx ...

  • RAD Data comm HCD-E1 - page 168

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-28 Diagnostic Tests 01/01/01 08:15 To activate or deactivate a specific test, use the following procedure: Step Action Key Result 1 Bring the cursor to the left-hand field in the top row (if it is not already there). CURSOR 2 Scroll to display TEST OPTION in th ...

  • RAD Data comm HCD-E1 - page 169

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Diagnostic Tests 5-29 Step Action Key Result 7 Bring the cursor to the left-hand field in the second row, and scroll to display the desired type of loopback: LOCAL CH (data channel local loopback) REM CH (data channel remote loopback) REM REM CH (d ...

  • RAD Data comm HCD-E1 - page 170

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-30 Diagnostic Tests 01/01/01 08:15 To display the current parameter values, and change them as necessary, use the following procedure: Step Action Key Result 1 Check/configure your channel according to Chapter 3 (see Checking the Current Operating Configuration ...

  • RAD Data comm HCD-E1 - page 171

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Configuration Error Messages 5-31 Step Action Key Result 16 To deactivate the BERT test, scroll to OFF and press ENTER. ENTER 17 Deactivate the loopback on the appropriate channel as described in the previous section. Operating Loopbacks from a Con ...

  • RAD Data comm HCD-E1 - page 172

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-32 Configuration Error Messages 01/01/01 08:15 Table 5-5 Configuration Error Messages (Cont.) Error Code Terminal Message and Description ERROR 05 MASTER AND FALLBACK CLOCK ARE THE SAME You are trying to select the same source as both master and fallback clock ...

  • RAD Data comm HCD-E1 - page 173

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Configuration Error Messages 5-33 Table 5-5 Configuration Error Messages (Cont.) Error Code Terminal Message and Description ERROR 17 TS 0 IS MAPPED TO G732N FRAME TYPE You are trying to assign TS 0 for the G732N frame type ERROR 18 Reserved for fu ...

  • RAD Data comm HCD-E1 - page 174

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-34 Troubleshooting 01/01/01 08:15 5.6 Power-Up Self-Test HCD-E1 performs a power-up self-test upon turn-on. The self-test sequence, described in Section 3-5 , tests the critical circuit functions and the display. In case of failure, HCD-E1 displays an appropria ...

  • RAD Data comm HCD-E1 - page 175

    HCD-E1 Installation & Operation Manual Chapter 5 - Troubleshooting and Diagnostics 01/01/01 08:15 Troubleshooting 5-35 Table 5-6 Troubleshooting Chart (Cont.) No. Trouble Symptoms Probable Cause Corrective Measures 3 E1 LOS LOC indicator lights (sublink loses frame synchronization). External problem Check the cable connected to the E1 equipment ...

  • RAD Data comm HCD-E1 - page 176

    Chapter 5 - Troubleshooting and Diagnostics HCD-E1 Installation & Operation Manual 5-36 Troubleshooting 01/01/01 08:15 ...

  • RAD Data comm HCD-E1 - page 177

    30 6103(QYLURQPHQW $ $SSHQGL[$ 61030DQDJHPHQW $ 6FRSH 7KLVDSSHQGL[SURYLGHVWKHVSHFLILFLQIRUPDWLRQUHTXLUHGIRUWKH PDQDJHPHQWRI+&'(EPHDQVRIWKH6LPSOH1HWZRUN0DQDJHPHQW 3URWRFRO6103 $Q+&'( ...

  • RAD Data comm HCD-E1 - page 178

    $SSHQGL[$61030DQDJHPHQW +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $ 6103(QYLURQPHQW 30 61032SHUDWLRQV 7KH6103SURWRFROLQFOXGHVIRXUWSHVRIRSHUDWLRQV JHW5HTXHVW &RPPDQGIRUUHWULHYLQJVSHFLILFPDQDJHPHQW LQIRUPDWLRQIURPW ...

  • RAD Data comm HCD-E1 - page 179

    +&'( ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $SSHQGL[$61030DQDJHPHQW 30 6103(QYLURQPHQW $ SULYDWHHQWHUSULVHVSHFLILFEUDQFKRI0,%VHDFKHQWHUSULVHPDQXIDFWXUHU FDQEHDVVLJQHGDQXPEHUZKLFKLVLWVHQWHUSULVHQXP ...

  • RAD Data comm HCD-E1 - page 180

    $SSHQGL[$61030DQDJHPHQW +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $ ,3(QYLURQPHQW 30 $FFHVV5HVWULFWLRQ8VLQJ6103&RPPXQLWLHV ,QJHQHUDO6103DJHQWVVXSSRUWWZRWSHVRIDFFHVVULJKWV • 5HDGRQO WKH6103DJHQW? ...

  • RAD Data comm HCD-E1 - page 181

    +&'( ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $SSHQGL[$61030DQDJHPHQW 30 ,3(QYLURQPHQW $ $ ,3(QYLURQPHQW *HQHUDO 7KH6103DJHQWRI+&'(FDQFRPPXQLFDWHHLWKHURXWRIEDQGRULQEDQG • 2XWRIEDQG? ...

  • RAD Data comm HCD-E1 - page 182

    $SSHQGL[$61030DQDJHPHQW +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $ ,3(QYLURQPHQW 30 ,3$''5(66 %WH %WH %WH %WH &ODVV$ 1HWZRUN3RUWLRQ +RVW3RUWLRQ &ODVV% 1HWZRUN3RUWLRQ +RVW3RUWLRQ &ODVV& ...

  • RAD Data comm HCD-E1 - page 183

    +&'( ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $SSHQGL[$61030DQDJHPHQW 30 61037UDSV $ $XWRPDWLF5RXWLQJRI,37UDIILF 7KH6103DJHQWRIWKH+&'(XQLWVLQFOXGHVDSURSULHWDU,3URXWHU IXQFWLRQWKDWLVXVHGWR? ...

  • RAD Data comm HCD-E1 - page 184

    $SSHQGL[$61030DQDJHPHQW +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $ 61037UDSV 30 ...

  • RAD Data comm HCD-E1 - page 185

    30 +'6//LQHV&RQQHFWRU % $SSHQGL[% &RQQHFWRU:LULQJ % (6XEOLQN&RQQHFWRUV 7KH(VXEOLQNXQEDODQFHGLQWHUIDFHLVWHUPLQDWHGLQWZR%1&FRQQHFWRUV GHVLJQDWHG7;,1DQG5;287 7KH(VXEOLQNEDODQFHGLQ ...

  • RAD Data comm HCD-E1 - page 186

    $SSHQGL[%&RQQHFWRU:LULQJ +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO % '&(,QWHUIDFH&RQQHFWRUVDQG$GDSWHU&DEOHV 30 7DEOH%1(7:25.+'6/&RQQHFWRU3LQ$OORFDWLRQ 3LQ )XQFWLRQ  /LQH$  /LQH$ ...

  • RAD Data comm HCD-E1 - page 187

    +&'( ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $SSHQGL[%&RQQHFWRU:LULQJ 30 '&(,QWHUIDFH&RQQHFWRUVDQG$GDSWHU&DEOHV % 56,QWHUIDFH :KHQ+&'(LVRUGHUHGZLWKDQ56LQWHUIDFHW ...

  • RAD Data comm HCD-E1 - page 188

    $SSHQGL[%&RQQHFWRU:LULQJ +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO % '&(,QWHUIDFH&RQQHFWRUVDQG$GDSWHU&DEOHV 30 956 ,QWHUIDFH :KHQRXRUGHUDQ+&'(ZLWKWKH9 ...

  • RAD Data comm HCD-E1 - page 189

    +&'( ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $SSHQGL[%&RQQHFWRU:LULQJ 30 '&(,QWHUIDFH&RQQHFWRUVDQG$GDSWHU&DEOHV % 9,QWHUIDFH :KHQRXRUGHUDQ+&'(ZLWKWKH9LQWHUIDFHLW? ...

  • RAD Data comm HCD-E1 - page 190

    $SSHQGL[%&RQQHFWRU:LULQJ +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO % &RQWURO3RUW&RQQHFWRU 30 ;,QWHUIDFH :KHQRXRUGHUDQ;LQWHUIDFHLWDUULYHVZLWKWKH'&(WLPLQJPRGHFDEOH &%/+6 ...

  • RAD Data comm HCD-E1 - page 191

    +&'( ,QVWDOODWLRQ2SHUDWLRQ0DQXDO $SSHQGL[%&RQQHFWRU:LULQJ 30 &RQWURO3RUW&RQQHFWRU % % &RQWURO3RUW&RQQHFWRU 7KH+&'(FRQWUROSRUWKDVDVWDQGDUG569? ...

  • RAD Data comm HCD-E1 - page 192

    $SSHQGL[%&RQQHFWRU:LULQJ +&'(  ,QVWDOODWLRQ2SHUDWLRQ0DQXDO % &RQWURO3RUW&RQQHFWRU 30 ...

  • RAD Data comm HCD-E1 - page 193

    General Description C-1 Appendix C IR-ETH Interface Module C.1 General Description IR-ETH is an interface module for RAD modems, used for converting the Ethernet (10BaseT or 10Base2) electrical levels to the modem TTL levels. It also converts the Ethernet protocol to HDLC to enable long-distance transmission and avoid the Ethernet collision limitat ...

  • RAD Data comm HCD-E1 - page 194

    Appendix C - IR-ETH Interface Module HCD-E1 Installation & Operation Manual C-2 Technical Specifications C.2 IR-ETH Connector Options Figure C-2 and Figure C-3 show the rear panel of HCD-E1 with the IR-ETH connector options. ALM R L Y TX IN SUB E1 RX OU T NET WOR K LINE A 12 HDSL LINE B 4 5 P O W E R CHA NN EL CH. 1 CH. 2 10 BASE-T TX RX COLL L ...

  • RAD Data comm HCD-E1 - page 195

    HCD-E1 Installation & Operation Manual Appendix C - IR-ETH Interface Module 31/12/2000 17:57 Installation and Operation C-3 C.4 Installation and Operation Figure C-4 and Figure C-5 show the Ethernet bridge rear panel components for the 10BaseT and the 10Base2 versions, respectively. Figure C-6 shows the location of the LED and the DIP switch. V ...

  • RAD Data comm HCD-E1 - page 196

    Appendix C - IR-ETH Interface Module HCD-E1 Installation & Operation Manual C-4 Installation and Operation 1 2 3 4 Vie w A Figure C-6 IR-ETH Module (View A) LAN Installation The Ethernet with UTP (10BaseT) connectors is designated as a Station. For 10BaseT installation, either a straight cable or a cross-cable may be required. Use a cross-cable ...

  • RAD Data comm HCD-E1 - page 197

    HCD-E1 Installation & Operation Manual Appendix C - IR-ETH Interface Module 31/12/2000 17:57 Installation and Operation C-5 Table C-2 DIP Switch Settings Section Number Name Description Default Setting 1 SQ/FD Controls Ethernet mode: full-duplex or half-duplex. Permanently OFF 2 CMP ON: Strips padding bits inserted in 64-byte frame OFF: Transmi ...

  • RAD Data comm HCD-E1 - page 198

    Appendix C - IR-ETH Interface Module HCD-E1 Installation & Operation Manual C-6 Installation and Operation ...

  • RAD Data comm HCD-E1 - page 199

    General D-1 Appendix D IR-ETH/Q Interface Module D.1 General IR-ETH/Q is an interface module for RAD modems, used for converting the Ethernet 10BaseT electrical levels to the modem TTL levels. It converts the Ethernet protocol to HDLC to enable long distance transmission and avoid the Ethernet collision limitation. The IR-ETH/Q module also supports ...

  • RAD Data comm HCD-E1 - page 200

    Appendix D - IR-ETH/Q Interface Module HCD-E1 Installation & Operation Manual D-2 Technical Specifications D.2 IR-ETH/Q Connector Figure D-2 shows the rear panel of HCD-E1, equipped with IR-ETH/Q module. Table D-1 lists the module RJ-45 connector pinout. ALM R LY TX IN S UB E1 RX OUT NETWOR K LINE A 12 HDSL LINE B 4 5 P O W E R CHANNE L CH.1 CH ...

  • RAD Data comm HCD-E1 - page 201

    HCD-E1 Installation & Operation Manual Appendix D - IR-ETH/Q Interface Module Installation and Operation D-3 D.4 Installation and Operation Figure D-3 shows the IR-ETH/Q rear panel. Figure D-4 shows the DIP switch, which is located on the reverse side of the board. Figure D-3 IR-ETH/Q Module Layout Figure D-4 DIP Switch Location ...

  • RAD Data comm HCD-E1 - page 202

    Appendix D - IR-ETH/Q Interface Module HCD-E1 Installation & Operation Manual D-4 Installation and Operation Setting the DIP Switch Configure the IR-ETH/Q module by setting the DIP switch in accordance with Table D-2 . The DIP switch is located on the reverse side of the IR-ETH/Q module. To change the switch settings, you must undo three screws ...

  • RAD Data comm HCD-E1 - page 203

    Introduction E-1 Appendix E IR-IP Interface Module E.1 Introduction Introduction IR-IP is a high-performance, miniature IP router based on RAD's unique IP router chip, the ChipRouter. IR-IP works by taking each Ethernet frame from the LAN and determining whether the IP packet is destined for the IP net on the Ethernet LAN. If not, IR-IP forwar ...

  • RAD Data comm HCD-E1 - page 204

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-2 Physical Descriptionr Application Figure E-1 shows a typical application of HCD-E1 with the IR-IP module. Router HCD-E 1 wit h IR-IP HCD-E 1 wi th V .35 Int erface Router Figure E-1 Typical Application of HCD-E1 with IR-IP Module E.2 Technical Specifications Router L ...

  • RAD Data comm HCD-E1 - page 205

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Physical Descriptionr E-3 IR-IP LEDs IR-IP contains three LEDs, which indicate the module activity. Table E-1 lists the LEDs functions. Table E-1 IR-IP LEDs Functions Name Type Function INT Green LED ON when IR-IP is powered up. ACT Yellow LED Blinks when there is transm ...

  • RAD Data comm HCD-E1 - page 206

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-4 IR-IP Management Subsystem, General Table E-3 lists the module RJ-45 connector pinout. Table E-3 IR-IP Connector Pinout Pin Name Function 1 TD (+) Transmit data positive 2 TD (-) Transmit data negative 3 RD (+) Receive data positive 6 RD (-) Receive data negative E.4 ...

  • RAD Data comm HCD-E1 - page 207

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Performing Preliminary Configuration E-5 When the factory-default parameters are used, the ERR indicator located on the HCD-E1 rear panel, near the IR-IP Ethernet interface connector flashes rapidly (about three times per second). The flashing of the ERR indicator also s ...

  • RAD Data comm HCD-E1 - page 208

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-6 Performing Preliminary Configuration 3. Establish communication with IR-IP and assign the prescribed IP address to its LAN interface. 4. Establish again communication with IR-IP and continue the preliminary configu ration in accor dance with the Quick Setup Menu sect ...

  • RAD Data comm HCD-E1 - page 209

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Performing Preliminary Configuration E-7 IP Learning Mechanism To simplify the configuration process, IR-IP has a special mechanism for configuring the IP address of its LAN interface. Setting section 1, called IP address lea rn in g, of th e IR-I P DI P sw itc h ( Figur ...

  • RAD Data comm HCD-E1 - page 210

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-8 Performing Preliminary Configuration 4. Send a ping to the new address to be used by IR-IP. A confirmation should be received after the third ping : after the confirmation, the flashing will slow down to approximately twice a second. If your host does not begin to re ...

  • RAD Data comm HCD-E1 - page 211

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module IR-IP Management Utility E-9 After turn-on, the ERR indicator lights for 15 seconds and then turns off. ACT does not light, and there is no response from IR-IP No software loaded into IR-IP. Download software using the procedure described in the New Software Download Men ...

  • RAD Data comm HCD-E1 - page 212

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-10 IR-IP Management Utility Starting a Management Utility The management utility is started automatically when Telnet communication is established. If password protection is enabled (see the Management Access Menu section below), you will be prompted to enter the Telne ...

  • RAD Data comm HCD-E1 - page 213

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Quick Setup Menu E-11 E.7 Quick Setup Menu The Quick Setup menu is used to select the main parameters’ values that must be defined before you start using IR-IP. Use the Advanced Setup menu (see the Advanced Setup Menu section below) to specify values for other IR-IP co ...

  • RAD Data comm HCD-E1 - page 214

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-12 Quick Setup Menu WAN IP Address Used to enter the IP address for the IR-IP WAN interface, i.e., the IP address to be used by IP hosts on the WAN to reach this IR-IP interface module. If the WAN IP Address field remain blank, IR-IP operates in the Unnumbered Router M ...

  • RAD Data comm HCD-E1 - page 215

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Management Access Menu E-13 E.8 Management Access Menu The Management Access menu is used to enable the use of passwords to protect the access to IR-IP management utility, and control the inactivity time-out interval. When password protection is enabled, a Telnet managem ...

  • RAD Data comm HCD-E1 - page 216

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-14 Advanced Setup Menu E.9 Advanced Setup Menu The Advanced Setup menu is used to select the desired group of IR-IP configuration parameters. The parameters accessed through Advanced Setup menu supplement the parameters available on the Quick Setup screen, by providing ...

  • RAD Data comm HCD-E1 - page 217

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Advanced Setup Menu E-15 Device Name Select this parameter to assign an arbitrary name to IR-IP for identification by the system manager (up to eight characters). The assigned name is displayed in the screen header. Contact Person Select this parameter to enter the name ...

  • RAD Data comm HCD-E1 - page 218

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-16 Advanced Setup Menu WAN Status Used to enable/disable the flow of packets through the WAN interface: • Open – the flow of packets is enabled. • Closed – the flow of packets through the WAN interface is disabled. As a result, IR-IP does not accept from, nor s ...

  • RAD Data comm HCD-E1 - page 219

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Advanced Setup Menu E-17 DLCI When the Self Learn parameter is DISABLED, use this parameter to specify the DLCI used for exchanging maintenance protocol messages. CIR Used to specify the maximum amount of data, in bits, which the Frame Relay network guarantees to transfe ...

  • RAD Data comm HCD-E1 - page 220

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-18 Advanced Setup Menu Protocol Field Compression Used to control the use of protocol field compression type according to RFC 1661. It is strongly recommended that this compression be used for troubleshooting only. Authentication Protocol Used to select the authenticat ...

  • RAD Data comm HCD-E1 - page 221

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Advanced Setup Menu E-19 Multicast IP Menu The Multicast IP menu is used to specify the IP multicast frame forwarding parameters, and to access the static multicast groups’ table. To access the Multicast IP menu: • From the Advanced Setup menu, press 4 . The Multicas ...

  • RAD Data comm HCD-E1 - page 222

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-20 Device Control Menu Static Groups Select this parameter to access the static multicast groups table. The table is used to specify the IP addresses for up to 10 IP multicast groups. You can add, change, or delete each entry in the table (see the prompt line). To acce ...

  • RAD Data comm HCD-E1 - page 223

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Device Control Menu E-21 New Software Download Menu IR-IP operates as a TFTP client, and therefore it is possible to update its software by downloading new software from another computer that operates as a TFTP server. The New Software Download menu is used to specify th ...

  • RAD Data comm HCD-E1 - page 224

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-22 Device Control Menu View Error Log Screen This item of the Device Control submenu is used to view the error log file. This file logs errors detected in IR-IP for debug and technical support purposes. Resets Menu The Resets menu allows you to perform reset of IR-IP, ...

  • RAD Data comm HCD-E1 - page 225

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module View Menu E-23 Reset WAN To reset the WAN interface: • From the Resets menu, type 3 . You will be prompted to confirm the reset operation. Note Resetting the WAN interface causes the WAN controller to be restarted. This results in renegotiation of the WAN protocol para ...

  • RAD Data comm HCD-E1 - page 226

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-24 View Menu To access the Configuration and Connection screen: • From the View menu, type 1 . The View Configuration screen appears ( Figure E-20 ). IR_IP <IR-IP> S/W Ver. 1.00 31/IR (date) VIEW CONFIGURATION ------------------ BOOT Version :1.06 18.03.1999 De ...

  • RAD Data comm HCD-E1 - page 227

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module View Menu E-25 Multicast Groups Table Screen This screen is used to display information about the multicast group IP addresses and their status. To access the Multicast Groups Table screen: • In the View menu, type 3 . The Multicast Groups Table screen appears ( Figure ...

  • RAD Data comm HCD-E1 - page 228

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-26 Diagnostic Tool (PING Terminal) Menu IR_IP <IR-IP> S/W Ver.1.00 31/IR (date) SYSTEM STATISTICS ----------------- Counter Name Val Counter Name Val WAN in Octets 83504 WAN Alignment Errors 0 WAN Out Octets 1950 WAN Aborted Frames 0 WAN Out Frames 1723 WAN Short ...

  • RAD Data comm HCD-E1 - page 229

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Diagnostic Tool (PING Terminal) Menu E-27 Using the Ping Function The Ping option is used to confirm IP connectivity by pinging other IP hosts. Connectivity is confirmed by receiving a reply from the remote (pinged) IP host. To ping a host: 1. From the Diagnostic Tools m ...

  • RAD Data comm HCD-E1 - page 230

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-28 Erasing IR-IP Software E.13 Erasing User’s Configuration The user-defined configuration parameters are stored in the IP router card flash memory. After the user-defined configuration parameters are erased, the IP router card automatically loads the factory-default ...

  • RAD Data comm HCD-E1 - page 231

    HCD-E1 Installation & Operation Manual Appendix E - IR-IP Interface Module Erasing IR-IP Software E-29 Erasing Application Software To erase the application software: 1. Turn HCD-E1 off. 2. Set all the four sections of IR-IP DIP switch to ON. 3. Turn HCD-E1 on and monitor the IR-IP ERR indicator: it must turn on and light steadily. 4. While the ...

  • RAD Data comm HCD-E1 - page 232

    Appendix E - IR-IP Interface Module HCD-E1 Installation & Operation Manual E-30 Erasing IR-IP Software ...

Manufacturer RAD Data comm Category Modem

Documents that we receive from a manufacturer of a RAD Data comm HCD-E1 can be divided into several groups. They are, among others:
- RAD Data comm technical drawings
- HCD-E1 manuals
- RAD Data comm product data sheets
- information booklets
- or energy labels RAD Data comm HCD-E1
All of them are important, but the most important information from the point of view of use of the device are in the user manual RAD Data comm HCD-E1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals RAD Data comm HCD-E1, service manual, brief instructions and user manuals RAD Data comm HCD-E1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product RAD Data comm HCD-E1.

A complete manual for the device RAD Data comm HCD-E1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use RAD Data comm HCD-E1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of RAD Data comm HCD-E1.

A complete RAD Data comm manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual RAD Data comm HCD-E1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the RAD Data comm HCD-E1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the RAD Data comm HCD-E1, that we can find in the current document
3. Tips how to use the basic functions of the device RAD Data comm HCD-E1 - which should help us in our first steps of using RAD Data comm HCD-E1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with RAD Data comm HCD-E1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of RAD Data comm HCD-E1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning RAD Data comm HCD-E1?

Use the form below

If you did not solve your problem by using a manual RAD Data comm HCD-E1, ask a question using the form below. If a user had a similar problem with RAD Data comm HCD-E1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)