Manual Thermador PHH30DS

32 pages 2.31 mb
Download

Go to site of 32

Summary
  • Thermador PHH30DS - page 1

    VENTILA TION INST ALL A TION MANUAL MODELS: PHH30DS PHH36DS ...

  • Thermador PHH30DS - page 2

    2 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Safety Warning: Turn off power circu ...

  • Thermador PHH30DS - page 3

    3 IMPOR T ANT SAFETY INSTRUCTIONS Read All Instructions Before Using the Appliance. READ AND SA VE THESE INSTRUCTIONS W ARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. B. Before servicing ...

  • Thermador PHH30DS - page 4

    4 Electrical requirements IMPORT ANT Observe all governing codes and ordinances. It is the customer’s responsibility: To contact a qualified electrical installer. To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical ...

  • Thermador PHH30DS - page 5

    5 Parts Included with your Hood • Hood Canopy Assembly with blower already installed • Grease filters • Drip trays • Care & Use /Installation Instructions • Fittings bag with: 2 drip trays holding brakets + plastic wahers and knobs 4 Washers 6 Drywall anchors 2 Hooks with regulating screws 6 Screws 5X35 4 screws 2,9 6,5 for transition ...

  • Thermador PHH30DS - page 6

    6 Round Duct Soffit Transition Filter Blower Lamp Hood 24” to 30” • Typical installation The height from the countertop to the bottom of the hood is 24" to 30”.These hoods are not recommended to be used over indoor grills. 1. Choose vent options The hood is designed ready to be used for vertical discharge as shown below. Note: see also ...

  • Thermador PHH30DS - page 7

    7 TOT AL (of both columns)= ...

  • Thermador PHH30DS - page 8

    8 T ABLE 2. DUCTWORK INST ALLA TION GUIDELINES For safety reasons, ducting should vent directly outdoors (not into an attic, underneath the house, into the garage or into any enclosed space). Keep duct runs as short and straight as possible. Duct fittings (elbows and transitions) reduce air flow efficiency. Back to back elbows and „S“ turns giv ...

  • Thermador PHH30DS - page 9

    9 2. Discharge Direction: The hood is shipped ready for vertical discharge. WARNING! Before installing remove the knock-out plate that close the air outlet on the top if is desired to use the range hood for vertical discharge OR the rear outlet if is desired to use the range hood for horizontal discharge. (see also Figure 5). WARNING! Once the Knoc ...

  • Thermador PHH30DS - page 10

    10 W all Mount Installation Note: see below if cabinet installation is preferred 4. After the hood installation height has been determined draw a horizontal line at a distance above the cooktop equal to the desired hood installation height plus 7- 1/ 2” . See also Figure 6a. 5. Find the centerline of the cooktop. Draw a vertical line along this c ...

  • Thermador PHH30DS - page 11

    11 Fix Duct to transition and seal with tape. For both installation method: 11.Wiring the HOOD: WARNING Electrical Shock Hazard Warning: Turn off power at the service panel before wiring this unit. 120 VAC, 15 or 20 Amp circuit required. ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF ...

  • Thermador PHH30DS - page 12

    12 MERCI DE LIRE TOUTES LES INSTRUCTIONS AVANT DE PROCéDER AU MONTAGE. L’INSTALLATION DOIT êTRE CONFORME AUX RéGLEMENTATIONS LOCALES. IMPORTANT : Conserver ces instructions pour l’organisme de contrôle des installations électriques. L’INSTALLATEUR doit laisser ce manuel d’instructions de l’appareil au propriétaire. LE PROPRIéTAIRE ...

  • Thermador PHH30DS - page 13

    13 A VERTISSEMENT POUR DIMINUER LE RISQUE D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURE, SUIVRE LES INDICATIONS SUIVANTES : A. Utiliser cet appareil uniquement pour l’usage prévu par le fabriquant. Si vous avez des questions, contacter le fabriquant. B. Avant d’entretenir ou de nettoyer l’appareil, couper le courant au niveau de la boîte ...

  • Thermador PHH30DS - page 14

    14 IMPORT ANT Conserver ces instructions de montage pour l’organisme de contrôle des installations électriques . La hotte doit être raccordée uniquement avec du fil électrique en cuivre. La hotte doit être raccordée directement à la boîte des fusibles (ou interrupteur de circuit) par un conduit métallique. La dimension des fils électri ...

  • Thermador PHH30DS - page 15

    15 Éléments compris avec votre hotte • Corps de la hotte avec ventilateur déjà installé • Filtres à graisses • Égouttoirs • Manuel d’Utilisation et d’Entretien/d’Installation • Kit de fixation comprenant : 2 fixations pour égouttoirs+bagues en plastique et poignées de réglages 4 Bagues d’appui 6 Attaches pour mur 2 Croch ...

  • Thermador PHH30DS - page 16

    16 • Installation classique La hauteur d’installation de votre hotte par rapport à la partie supérieure de votre cuisinière doit être de 76 à 91 cm (24" à 30 »). Cette hotte n’est pas recommandée pour l’utilisation sur des grills internes. 1. Choisir le type d’évacuation Cette hotte est conçue pour être utilisée avec une ...

  • Thermador PHH30DS - page 17

    17 6 po 7 po 8 po 10 po 3-1/4 po x 10 po 3-1/4 po x 14 po 8 po 7 po 6 po 6 po 8 po 7 po 6 po 7 po 6 po 6 po 6 po 7 po 7 po 7 po po po po pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi pi TOT AL (2 colonnes)= ...

  • Thermador PHH30DS - page 18

    18 TABLEAU 2. RECOMMANDA TIONS POUR L ’INST ALLA TION DES CONDUITS. Pour des raisons de sécurité, l’évacuation doit s’effectuer directement vers l’extérieur (pas dans un grenier, sous la maison, dans le garage ou dans tout autre endroit dans le bâtiment). Utiliser les conduits les plus droits et les plus courts possible. Les courbures ...

  • Thermador PHH30DS - page 19

    19 2. Direction d’évacuation : La hotte est livrée pour une évacuation verticale. AVERTISSEMENT ! Avant d’installer la hotte, enlever la plaquette qui ferme l’évacuation d’air se trouvant sur la partie supérieure si vous préférez une évacuation verticale OU la plaquette se trouvant à l’arrière si vous souhaitez une évacuation h ...

  • Thermador PHH30DS - page 20

    20 Installation au mur Note : Si vous choisissez la formule encastrée, passer au point suivant. 4. Après avoir déterminé la hauteur d’installation de la hotte, tracer une ligne horizontale à une distance de la cuisinière de 19 cm (7 ½ «) au- dessus de la hauteur choisie, voir Figure 6a. 5. Déterminer la ligne centrale de la cuisinière. ...

  • Thermador PHH30DS - page 21

    21 Note: Si cela est possible, fixer la hotte au mur en 4 autres points (2 sur le dessus et 2 sur le dessous). 10. De l’intérieur du meuble, fixer le raccord sur le trou d’évacuation supérieur (évacuation verticale - voir aussi Attacher le raccord de 8" , page précédente). Pour les 2 types d’installations: 11. Raccorder la HOTTE : ...

  • Thermador PHH30DS - page 22

    22 LEER LAS INSTRUCCIONES ANTES DEL USO LA INSTALACION DEBE ACORDAR CON TODOS LOS CODIGOS LOCALES IMPORTANTE.: CONSERVAR estas instrucciones para ser usadas por el Inspector Local INSTALADOR: por favor dejar estas instrucciones con esta unidad para el propietario PROPIETARIO: por favor conservar estas instrucciones para referencias futuras Aviso de ...

  • Thermador PHH30DS - page 23

    23 ADVERTENCIA ATENCION SOLO PARA USO GENERAL DE VENTILACIÓN. NO USAR PARA EXTRAER MATERIALES EXPLOSIVOS, O VAPORES PELIGROSOS. ATENCIÓN Para reducir el riesgo de incendios y para una adecuada descarga del aire, asegurarse que el aire vaya hacia afuera - no proveer salida al aire de descarga hacia los espacios con paredes, techos, áticos, espaci ...

  • Thermador PHH30DS - page 24

    24 IMPORT ANTE Guardar las Instrucciones de Instalación para el uso del inspector eléctrico . La campana de cocina debe conectarse sólo con alambre de cobre. La campana de cocina debe conectarse directamente a la caja del fusible desconectado (o cortacircuitos) a través del conducto eléctrico metálico. Los tamaños del alambre deben ser confo ...

  • Thermador PHH30DS - page 25

    25 Partes Incluidas con la Camp ana • Montaje campana con aspirador ya instalado • Filtros de grasa • Depósitos de deshielo • Cura y Uso / Instrucciones de Instalación • Bolsa de accesorios con: 2 soportes de contención para los depósitos de deshielo + arandelas plásticas y botones 4 arandelas 6 anclas para pared 2 ganchos con tornil ...

  • Thermador PHH30DS - page 26

    26 Conducto redondo Sofito Transición Filtros Lampara 24” to 30” Aspirador requisitos específicos en su área. • Instalación típica La altura desde la encimera hasta el fondo de la campana es 24" a 30". Estas campanas no son recomendadas para ser usadas encima de las parrillas interiores. 1. Escoger las opciones de ventilación ...

  • Thermador PHH30DS - page 27

    27 27 TOT AL (de ambas columnas)= ...

  • Thermador PHH30DS - page 28

    28 T ABLA 2. DIRECTRICES DE INST ALACIÓN DEL TRABAJO DEL CONDUCTO Por motivos de seguridad, la propagación guiada debe dar salida directamente al aire libre (no en un ático, debajo de la casa , en el garaje o en cualquier espacio asociado). Hacer si que el conducto sea lo más corto y lo más derecho posible. Los montajes del conducto (los codos ...

  • Thermador PHH30DS - page 29

    29 2. Dirección de la descarga: La campana se envía ya lista para la descarga vertical . ¡ADVERTENCIA! Antes de instalar quitar la placa expulsora exterior que cierra el conducto de evacuación del aire en la parte superior si se desea usar la campana de cocina para la descarga vertical O el conducto de evacuación del aire posterior si se desea ...

  • Thermador PHH30DS - page 30

    30 Instalación en la p ared nota: ver debajo si la instalación del gabinete es la preferida 4. Después que la altura de la instalación de la capucha haya sido determinada, dibujar una línea horizontal a una distancia sobre la superficie de cocina igual a la altura de instalación de la capucha deseada más 7 - 1 / 2" . También ver la Fig ...

  • Thermador PHH30DS - page 31

    31 Para ambos métodos de inst alación: 12. Conexión eléctrica ADVERTENCIA Riesgo de descarga eléctrica Advertencia: apagar el suministro de energía en el panel de servicio antes de conectar esta unidad. Circuito requerido de 120 VAC, 15 o 20 Amp. INSTRUCCIONES DE CONEXIÓN ELÉCTRICA ESTE APARATO TIENE UNA CAJA DE CONEXIÓN ELÉCTRICA CON 3 A ...

  • Thermador PHH30DS - page 32

    LI2W2A 5551 McFadden Avenue, Huntington Beach CA, 92649  800-735-4328  www .thermador .com 9000036121  10013 RevB  10/05 © BSH Home Appliances Corporation  Litho in U.S.A. ...

Manufacturer Thermador Category Ventilation Hood

Documents that we receive from a manufacturer of a Thermador PHH30DS can be divided into several groups. They are, among others:
- Thermador technical drawings
- PHH30DS manuals
- Thermador product data sheets
- information booklets
- or energy labels Thermador PHH30DS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Thermador PHH30DS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Thermador PHH30DS, service manual, brief instructions and user manuals Thermador PHH30DS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Thermador PHH30DS.

Similar manuals

A complete manual for the device Thermador PHH30DS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Thermador PHH30DS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Thermador PHH30DS.

A complete Thermador manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Thermador PHH30DS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Thermador PHH30DS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Thermador PHH30DS, that we can find in the current document
3. Tips how to use the basic functions of the device Thermador PHH30DS - which should help us in our first steps of using Thermador PHH30DS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Thermador PHH30DS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Thermador PHH30DS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Thermador PHH30DS?

Use the form below

If you did not solve your problem by using a manual Thermador PHH30DS, ask a question using the form below. If a user had a similar problem with Thermador PHH30DS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)