Manual Troy-Bilt TB144

56 pages 3.57 mb
Download

Go to site of 56

Summary
  • Troy-Bilt TB144 - page 1

    Operator’ s Manual 4-Cycle Gar den Cultivator TB144 SA VE THESE INSTRUCTIONS For service call 1-800-828-5500 in the United States, or 1-800-668-1238 in Canada to obtain a list of authorized service dealers near you. For more details about your unit, visit our website at www.troybilt.com . DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE ...

  • Troy-Bilt TB144 - page 2

    2 READ ALL INSTRUCTIONS BEFORE OPERATING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication. • Children and teens under the age of 15 must not use the unit, except for teens guided by an adult. • All ...

  • Troy-Bilt TB144 - page 3

    3 RULES FOR SAFE OPERATION SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING • ON/OFF STOP CONTROL ON / START / RUN ? ...

  • Troy-Bilt TB144 - page 4

    4 Tine Guard Cultivator Tines Primer Bulb Muffler Handlebar Knob Starter Rope Grip Handlebar Throttle Control Choke Control Edger Wheel Edger Blade STOP/OFF (O) START/ON (I) Wheel Support Bracket APPLICATIONS • Cultivating sod and light to medium soil • Cultivating in garden areas, around trees, etc. • Edging KNOW YOUR UNIT ...

  • Troy-Bilt TB144 - page 5

    5 NOTE: Before setting up your cultivator / edger, disconnect the spark plug wire from the spark plug. POSITIONING THE HANDLEBARS 1. Loosen the two knobs on the inside of the handlebars (Fig. 1). 2. With the unit upright, swing the handlebars up into the operating position (Fig. 1). NOTE: Take care not to pinch the throttle cable or switch wires wh ...

  • Troy-Bilt TB144 - page 6

    6 RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase is extremely important. Check the oil before each use and change the oil regularly. Using incorrect or dirty oil can cause premature engine wear and failure. Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SF, SG, SH. ADDING OIL ...

  • Troy-Bilt TB144 - page 7

    7 RECOMMENDED FUEL TYPE Old fuel is the primary reason for improper unit performance. Be sure to use fresh, clean, unleaded gasoline. NOTE: This is a four cycle engine. In order to avoid damage to the unit, do not mix oil with gasoline . Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, met ...

  • Troy-Bilt TB144 - page 8

    8 1. Check the oil level in the crankcase. Refer to Checking the Oil Level. 2. Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling the Unit. 3. Put the On/Off Stop Control in the ON [ I ] position (Fig. 10). 4. Place the choke lever in Position 1 (Fig. 11). 5. Fully press and release the primer bulb 10 times, slowly. Some amoun ...

  • Troy-Bilt TB144 - page 9

    9 TRANSPORTING THE UNIT 1. Stop the engine. 2. Tilt the unit back until the tines clear the ground. 3. Push or pull the unit to the next location to be cultivated. Fig. 13 OPERATING TIPS 1. Move the cultivator to the work area prior to starting the engine. Transport the cultivator by pushing or pulling it along on its wheels. 2. Start the unit by f ...

  • Troy-Bilt TB144 - page 10

    10 Click Pin “A” Tine Fig. 14 TINE REMOVAL AND REPLACEMENT All 4 tines should be replaced at the same time because they will wear evenly through normal use. Work on one side at a time. 1. Put the On/Off Stop Control in the STOP ( O ) position and disconnect the spark plug wire. NOTE: It may be necessary to lay the cultivator back in a horizonta ...

  • Troy-Bilt TB144 - page 11

    11 CHANGING THE OIL For a new engine, change the oil after the first 10 hours of operation. Change the oil while the engine is still warm. The oil will flow freely and carry away more impurities. 1. Unplug spark plug wire to prevent accidental starting. 2. Remove the oil fill plug/dipstick. 3. Pour the oil out of the oil fill hole and into a contai ...

  • Troy-Bilt TB144 - page 12

    12 3. Wash the filter in detergent and water (Fig. 20). Rinse the filter thoroughly and allow it to dry. 4. Apply enough clean SAE 30 motor oil to lightly coat the filter (Fig. 21). Fig. 20 CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable. An idle adjustment screw is reached though a hole in the top of the engine cover (Fig. 22). NO ...

  • Troy-Bilt TB144 - page 13

    13 Rocker Arm Cover Fig. 25 Spark Plug Hole Gasket Screw Fig. 24 MAINTENANCE AND REPAIR INSTRUCTIONS 7. Pull the starter rope slowly to bring the piston to the top of its travel, (known as top dead center). Check that: • The piston is at the top of its travel while looking in the spark plug hole (Fig. 26) • Both rocker arms move freely, and bot ...

  • Troy-Bilt TB144 - page 14

    14 REPLACING THE SPARK PLUG Use a replacement Champion RDZ19H spark plug. The correct air gap is 0.025 in. (0.635 mm.). Remove the plug after every 25 hours of operation and check its condition. 1. Stop the engine and allow it to cool. Grasp the plug wire firmly and pull the cap from the spark plug. 2. Clean dirt from around the spark plug. Remove ...

  • Troy-Bilt TB144 - page 15

    15 TROUBLESHOOTING If further assistance is requir ed, contact your authorized service dealer . CAUSE ACTION Air filter is plugged Replace or clean the air filter Old or improperly mixed fuel Drain gas tank and add fresh fuel Improper carburetor adjustment Adjust according to the Carburetor Adjustments section or take to an authorized service deale ...

  • Troy-Bilt TB144 - page 16

    16 *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, ...

  • Troy-Bilt TB144 - page 17

    17 NOTES ...

  • Troy-Bilt TB144 - page 18

    18 MANUF ACTURER’S LIMITED WARRANTY FOR: No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether written or oral, except as mentioned above, given b ...

  • Troy-Bilt TB144 - page 19

    Manuel de L'utilisateur Cultivateur de Jar din à 4-temps TB144 CONSERVEZ CES INSTRUCTIONS Obtenez la liste des concessionnaires agréés appelez le 1-800- 828-5500 aux États-Unis ou le 1-800-668-1238 au Canada. Pour de plus amples informations à propos de votre appareil, visitez www.troybilt.com . NE RETOURNEZ PAS L'APPAREIL AU DÉTAIL ...

  • Troy-Bilt TB144 - page 20

    F2 LISEZ TOUTES LES INSTRUCTIONS AVANT UTILISATION • Lisez soigneusement cette notice. Familiarisez-vous avec les commandes et la marche à suivre pour une bonne utilisation de l'appareil. • N’utilisez pas cet appareil lorsque vous êtes fatigué, malade, ou sous l’influence de l’alcool, de drogues, ou de médicaments. • Tout enfan ...

  • Troy-Bilt TB144 - page 21

    F3 CONSIGNES DE SÉCURITÉ SYMBOLES DE SÉCURITÉ ET INTERNATIONAUX Ce manuel de l'utilisateur décrit les symboles et pictogrammes de sécurité et internationaux pouvant apparaître sur ce produit. Consultez le manuel de l'utilisateur pour les informations concernant la sécurité, le montage, le fonctionnement, l'entretien et les ...

  • Troy-Bilt TB144 - page 22

    F4 USAGE Cet appareil sert à travailler le sol avant de le gazonner ainsi que des sols à texture légère ou moyenne. Il peut aussi être utilisé pour cultiver dans les jardins, autour des arbres, etc. Protecteur des dents Dents Poire d'amorçage Silencieux STOP/ARRÊT (O) ON/MARCHE (I) Manette des gaz Poignée de la corde de démarrage Gui ...

  • Troy-Bilt TB144 - page 23

    F5 REMARQUE : Cet appareil est expédié sans essence ou huile. Pour éviter tout dommage à l’appareil, consultez les informations sur l’huile et l’essence pour mettre l’huile et l’essence dans le carter-moteur avant d’essayer de le faire démarrer. REMARQUE : Avant de monter votre cultivateur/coupe- bordures, débranchez le câble de ...

  • Troy-Bilt TB144 - page 24

    F6 TYPE D’HUILE RECOMMANDÉ Il est extrêmement important d'utiliser les bons type et indice d'huile dans le carter-moteur. Vérifiez l'huile avant chaque utilisation et changez-la périodiquement. Le fait de ne pas utiliser la bonne huile ou d'utiliser une huile sale peut entraîner une usure et une défaillance prématurées ...

  • Troy-Bilt TB144 - page 25

    F7 TYPE CARBURANT RECOMMANDÉ En général, si l'appareil ne fonctionne pas correctement, c'est que le carburant est vieux ou mal mélangé. Prenez soin d'utiliser du carburant sans plomb frais et propre. REMARQUE : ceci est un moteur à quatre temps. Pour éviter d’endommager l’appareil, ne mélangez pas l’huile avec l’essen ...

  • Troy-Bilt TB144 - page 26

    Fig. 12 F8 INSTRUCTIONS DE DÉMARRAGE Fig. 10 Manette des gaz ARRÊT (O) ON/ MARCHE (I) Corde de démarrage Manette des gaz INSTRUCTIONS D'ARRÊT 1. Relâchez la manette des gaz. Laissez le moteur refroidir au ralenti. 2. Mettez la commande Marche/Arrêt Stop en position ARRÊT (O). 1. Vérifiez le niveau d'huile dans le carter moteur. Vo ...

  • Troy-Bilt TB144 - page 27

    F9 Fig. 13 CONSEILS D’UTILISATION 1. Déplacez le cultivateur vers le lieu de travail avant de démarrer le moteur. Vous pouvez le transporter sur ses roues ou en le tenant par le tube central de la poignée. 2. Démarrez l’appareil conformément aux instructions de démarrage. 3. Pendant que le moteur tourne et que les dents ne touchent pas le ...

  • Troy-Bilt TB144 - page 28

    F10 Dents“A” Fig. 14 RETRAIT ET REMPLACEMENT DE DENTS Vous devez remplacer les 4 dents en même temps parce qu’elles s’usent de manière égale. Commencez par un côté à la fois. 1. Mettez la commande Marche/Arrêt Stop en position ARRÊT (O). Positionnez et déconnectez le câble de la bougie. REMARQUE : Il peut s’avérer nécessaire d ...

  • Troy-Bilt TB144 - page 29

    F11 6. Si le niveau est trop bas, ajoutez un peu d'huile par l’orifice et revérifiez (Fig. 16). Continuez jusqu'à ce que le niveau d'huile atteigne le haut de la jauge. REMARQUE: Ne remplissez pas trop l’appareil. CHANGEMENT D’HUILE Si le moteur est neuf, changez l'huile après les 10 premières heures d’utilisation. M ...

  • Troy-Bilt TB144 - page 30

    F12 Fig. 20 5 . Pressez le filtre pour répartir et drainer l'excédent d'huile (Fig. 21). 6. Replacez le filtre et l’écran (Fig. 19). NOTE: Si vous faites fonctionner l'appareil sans filtre à air, vous ANNULEREZ la garantie. 7. Réplacez le couvercle du filtre à air. Placez les crochets à gauche du filtre à air dans les fente ...

  • Troy-Bilt TB144 - page 31

    F13 Fig. 24 Vis 2. Enlevez la vis derrière le couvercle du moteur (Fig. 24). ENTRETIEN ET RÉPARATIONS Fig. 25 Cache-culbuteur Trou de bougie 3. Déconnectez le câble de la bougie. 4. Nettoyez toute saleté de la bougie. Retirez la bougie de la culasse en tournant la douille de 5/8 po à gauche. 5. Déposez le couvercle du moteur. 6. Nettoyez tou ...

  • Troy-Bilt TB144 - page 32

    F14 REMPLACEMENT DE LA BOUGIE Utilisez une bougie 180852. L'écartement correct est de 0,635 mm (0,025 po). Retirez la bougie après 25 heures de fonctionnement et vérifiez son état. 1. Arrêtez le moteur et laissez-le refroidir. Saisissez fermement le câble de la bougie et retirez le capuchon de celle-ci. 2. Nettoyez toute saleté de la bo ...

  • Troy-Bilt TB144 - page 33

    CAUSE SOLUTION Carburant vieux Drainez le réservoir/ajoutez du carburant frais Mauvais réglage du carburateur Ajustez selon l'instruction ou faites-le régler par un concessionnaire agréé Filtre à air sale Remplacez ou nettoyez-le Pare-étincelles colmaté Nettoyez ou remplacez le pare-étincelles Accessoire de coupe engorgé d'herbe ...

  • Troy-Bilt TB144 - page 34

    F16 * Toutes les spécifications contenues dans ce manuel tiennent compte des dernières informations techniques disponibles au moment de mettre sous presse. Nous nous réservons le droit d'y apporter des modifications à tout moment, sans préavis. Type de moteur ................................................................................ ...

  • Troy-Bilt TB144 - page 35

    F17 REMARQUES ...

  • Troy-Bilt TB144 - page 36

    F18 GARANTIE LIMITÉE DU F ABRICANT POUR: Aucune garantie implicite, y compris toute garantie de valeur marchande ou d’adaptation à une fin particulière, ne s’applique après la période applicable de garantie expresse écrite ci-dessus concernant les pièces qui sont identifiées. Aucune autre garantie ou caution expresse, écrite ou orale, ...

  • Troy-Bilt TB144 - page 37

    Manual del Operador Cultivador para Jar dines de 4 Ciclos TB144 CONSERVE EST AS INSTRUCCIONES Llame 1-800-828-5500 en EE.UU. o al 1-800-668-1238 en Canada para obtener una lista de distribuidores de servicio localizados cerca de usted. Para obtener más detalles sobre su unidad, visite nuestro sitio en www.troybilt.com. NO REGRESE SU UNIDAD AL VEND ...

  • Troy-Bilt TB144 - page 38

    E2 LEA TODAS LAS INSTRUCCIONES ANTES DE OPERAR LA UNIDAD • Lea las instrucciones cuidadosamente. Familiarícese con los controles y el uso adecuado de la unidad. • No opere esta unidad cuando esté cansado, enfermo o bajo la influencia de alcohol, drogas o medicamentos. • Los niños y los adolescentes menores de 15 años de edad no deben usar ...

  • Troy-Bilt TB144 - page 39

    E3 NORMAS PARA UNA OPERACIÓN SEGURA SIMBOLOS DE SEGURIDAD E INTERNACIONALES Este manual del operador describe los símbolos y figuras de seguridad e internacionales que pueden aparecer en este producto. Lea el manual del operador para obtener información completa acerca de la seguridad, ensamble, operación y mantenimiento y reparación. SIMBOLO ...

  • Troy-Bilt TB144 - page 40

    E4 Mango de la cuerda de arranque Bombilla del cebador Rueda de la Bordeadora Cuchilla de la Bordeadora Ménsula de Soporte de la Rueda Perillas del manubrio Protección de las púas Púas Control del obturador Silenciador OFF/ APAGADO (O) ON/ ENCENDIDO (I) Control del regulador Manubrio APLICACION Use esta unidad para cultivar tierra herbosa y tie ...

  • Troy-Bilt TB144 - page 41

    E5 NOTE: Desde la posición de funcionamiento, se observa la referencia a la derecha o a la izquierda de la cultivadora / bordeadora. AJUSTE DE LA PROFUNDIDAD Para ajustar la ménsula de soporte de la rueda proceda de la siguiente manera: 1. Detenga el motor y desconecte la bujía para evitar un arranque accidental. 2. Extraiga la chaveta de retén ...

  • Troy-Bilt TB144 - page 42

    E6 Fig. 7 Fig. 8 Fig. 6 TIPO DE ACEITE RECOMENDADO El uso de un aceite del tipo y peso correctos en el cigüeñal es extremadamente importante. Verifique el aceite antes de cada uso y cambie el aceite con frecuencia. Si no usa el aceite correcto, o utiliza aceite sucio, puede causar el desgaste y falla prematuros del motor. Use un aceite de buena c ...

  • Troy-Bilt TB144 - page 43

    E7 TIPO DE COMBUSTIBLE RECOMENDADO El combustible viejo es la causa principal del mal funcionamiento de la unidad. Asegúrese de usar combustible nuevo, limpio y sin plomo. NOTA: Este es un motor de cuatro ciclos. Para evitar dañar su unidad, no mezcle el aceite con la gasolina. Definición de los combustibles de mezcla Los combustibles actuales c ...

  • Troy-Bilt TB144 - page 44

    E8 INSTRUCCIONES DE APAGADO 1. Saque la mano del control del regulador. Deje enfriar el motor en mínima. 2. Coloque el control de Encendido/Apagado (On/Off) en posición de APAGADO (O). 1. Verifique el nivel de aceite en el cárter del cigüeñal. Lea Inspección del Nivel de Aceite . 2. Llene el tanque de combustible con gasolina nueva, limpia y ...

  • Troy-Bilt TB144 - page 45

    E9 Transporte de la Unidad 1. Apague el motor. 2. Incline la unidad hacia atrás hasta que las púas desmalezan la tierra. 3. Empuje o lleve la unidad hasta el próximo lugar que deba cultivar. Fig. 13 CONSEJOS PARA LA OPERACIÓN 1. Mueva el cultivador al área de trabajo antes de arrancar el motor. Puede transportar el cultivador empujándolo sobr ...

  • Troy-Bilt TB144 - page 46

    E10 Diente “A” Fig. 14 REMOCIÓN Y REPOSICIÓN DE LAS PUAS Las 4 púas deben cambiarse al mismo tiempo debido a que se desgastarán en forma pareja con el uso normal. Trabaje en un lado por vez. 1. Coloque el control de encendido y apagado en la posición de APAGADO ( O ) y desconecte el cable de la bujía de encendido. NOTA: Puede ser necesari ...

  • Troy-Bilt TB144 - page 47

    tapón de relleno de aceite / varilla de medición E11 CAMBIO DEL ACEITE En un motor nuevo, cambie el aceite después de las 10 primeras horas de operación. Cambie el aceite mientras el motor aún está caliente. El aceite fluirá con libertad y llevará más impurezas. 1. Desenchufe el manguito de la bujía de encendido para eliminar el arranque. ...

  • Troy-Bilt TB144 - page 48

    E12 Fig. 20 5 . Apriete el filtro para esparcir y retirar el exceso de aceite (Fig. 21). 6. Vuelva a colocar el filtro (Fig. 19). NOTA: Si opera la unidad sin el filtro de aire, su garantía será ANULADA. 7 . Vuelva a instalar la cubierta del filtro de aire. Coloque los ganchos del lado derecho de la cubierta del filtro de aire dentro de las ranur ...

  • Troy-Bilt TB144 - page 49

    E13 INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN Fig. 24 Tornillo 3. Desconecte el cable de la bujía de encendido. 4. Limpie la suciedad de alrededor de la bujía de encendido. Saque la bujía de encendido de la cabeza del cilindro girando un casquillo de 16mm (5/8 pulgadas) en sentido antihorario. 5. Saque la cubierta del motor. 6. Limpie la suci ...

  • Troy-Bilt TB144 - page 50

    E14 INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN LIMPIEZA DE LA UNIDAD • Use un cepillo pequeño para limpiar la parte exterior de la unidad y para mantener los respiraderos libres de obstrucciones. • No use detergentes fuertes ni limpiadores derivados del petróleo como queroseno. Algunos limpiadores domésticos contienen aceites aromáticos c ...

  • Troy-Bilt TB144 - page 51

    E15 RESOLUCIÓN DE PROBLEMAS EL MOTOR NO ARRANCA EL MOTOR NO FUNCIONA EN MINIMA EL MOTOR NO ACELERA Si necesita asistencia adicional, comuníquese con su proveedor de servicio autorizado. CAUSA ACCIÓN El filtro de aire está obstruido Cambie o limpie el filtro de aire El combustible es viejo Drene el tanque de gasolina / Agregue combustible nueva ...

  • Troy-Bilt TB144 - page 52

    E16 * Toda las especificaciones contenidas en este manual se basan en la información más reciente disponible en el momento de impresión del manual. Nos reservamos el derecho de hacer cambios en cualquier momento sin aviso previo. Tipo de motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Troy-Bilt TB144 - page 53

    E17 PARTS LIST 1 69 54 55 56 57 59 58 52 53 60 61 63 73 64 76 79 80 81 78 75 82 83 84 86 85 77 87 88 89 90 88 74 72 71 70 62 3 16 17 18 19 20 21 22 23 24 25 26 20 27 29 31 33 4 5 8 11 6 7 9 10 13 43 12 15 14 44 42 45 46 47 28 32 35 36 38 40 37 41 34 68 66 67 49 65 39 39 2 58 30 91 50 51 48 REPLACEMENT P ARTS - MODEL TB144 4-CYCLE GAS CUL TIV A TOR ...

  • Troy-Bilt TB144 - page 54

    E18 PARTS LIST REPLACEMENT P ARTS - MODEL TB144 4-CYCLE GAS CUL TIV A TOR Item Part No. Description 49 753-04288 Palnut 50 753-1202 Plate Screw 51 753-05074 Pressure Plate Assembly (includes 50) 52 753-05072 Recoil Pulley Assembly (includes 49 & 57) 53 753-04286 Recoil Spring 54 791-182366 Nut Clip 55 753-05011 Pull Handle 56 791-611061 Rope Gu ...

  • Troy-Bilt TB144 - page 55

    E19 PARTS LIST Item Part No. Description 1 753-04042 Trottle Control 2 753-04043 Torsion Spring 3 791-182673 On/Off Switch 4 753-04044 Foam Grip 5 753-04147 Throttle Cable 6 753-04498 Upper Handle 7 791-182899 Bolt 8 753-04049 Cable Tie 9 753-04499 Flex Shaft 10 791-182677 Knob 11 753-04052 Shoulder Washer 12 753-04053 Lower Handle 13 753-04054 Scr ...

  • Troy-Bilt TB144 - page 56

    E20 GARANTÍA LIMIT ADA DEL F ABRICANTE P ARA: Ninguna garantía implícita es aplicable, incluyendo cualquier garantía implícita de comerciabilidad o idoneidad para un propósito particular, después del período de la garantía expresa escrita con anterioridad, con respecto a las piezas identificadas. Ninguna otra garantía expresa dada por cua ...

Manufacturer Troy-Bilt Category Cultivator

Documents that we receive from a manufacturer of a Troy-Bilt TB144 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- TB144 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt TB144
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt TB144.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt TB144, service manual, brief instructions and user manuals Troy-Bilt TB144. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt TB144.

Similar manuals

A complete manual for the device Troy-Bilt TB144, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt TB144 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt TB144.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt TB144 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt TB144, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt TB144, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt TB144 - which should help us in our first steps of using Troy-Bilt TB144
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt TB144
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt TB144 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt TB144?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt TB144, ask a question using the form below. If a user had a similar problem with Troy-Bilt TB144 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)