Manual Hitachi CU-HD1000

38 pages 2.44 mb
Download

Go to site of 38

Summary
  • Hitachi CU-HD1000 - page 1

    CAMERA CONTROL UNIT CU-HD1000 OPERATING INSTRUCTIONS Please read these operating instructions carefully for proper operation, and keep them for future reference. ...

  • Hitachi CU-HD1000 - page 2

    Note: The model and serial num bers of your product are im portant for you to keep for y our convenience and protection. These numbers appear on the nameplat e located on he bottom of the product. Please record these numbers in the spaces provided below, and re tain this m anual for future reference. M o d e l N o . S e r i a l N o . ...

  • Hitachi CU-HD1000 - page 3

    A SAFETY INSTRUCTIONS Carefully read all safety messages in this manual and safety Instructions on your equipment. Follow recommended precautions and safe operating practices. SAFETY ALERT SYMBOL This is the “Safety Alert Symbol.” This symbol is used to call your attention to items or operations that could be dangerous to you or other persons u ...

  • Hitachi CU-HD1000 - page 4

    B IMPORTANT SAFETY INSTRUCTIONS 1. Read Instructions All the safety and operati ng instructions should be read before the product is operate d. 2. Retain Instructions The safety and operating instruct ions shoul d be retained for future reference. 3. Heed Warnings All warnings on the product and the operat i ng instructions should be adhered to. 4. ...

  • Hitachi CU-HD1000 - page 5

    C 14. Lightning For added protecti on for this product during a light ning storm, or when it is left unattended and unused for l ong periods of time, unplug it from the wall outlet. Th is will prevent dam age to the product due to lightning and power-line surges. 15. Overloading Do not overload wall outlets, extension cord s or integral convenience ...

  • Hitachi CU-HD1000 - page 6

    D WICHTIGE SICHERHEITSANWEISUNGEN 1. Alle Anw eisungen lesen. Vor Betrieb des Erzeugnisses sollten alle Sicher heits-und Bedienungsanleit ungen gelesen werden. 2. Die Anw eisungen aufbew ahren. Die Sicherheits-und Bedienungsanleitungen sollte n fünftigen Bezug aufbewahrt werden. 3. Warnungen beachten. Die Warnungen auf dem Erzeugnis und in den Be ...

  • Hitachi CU-HD1000 - page 7

    E 12. Erdung oder Polarisierung Dieses Erzeugnis ist m it einem Schutzkontakt stecker mit drei Leite rn ausgerüstet, mit einem Erdungskontakt. Dieser Stecker paßt nur in ein schuko-Steckdose. Dies ist eine Sicherheitsm aßnahme. Wenn Sie den Stecker nicht in die Steckdose stecken können, so wenden Sie sich bitte an ihren Elektriker, damit er die ...

  • Hitachi CU-HD1000 - page 8

    F 21. Ersatzteile Wenn Ersatzteile erforderli ch sind, darauf achten, daß de r Wartungstechniker nur die vom Hersteller festgelegt en Ersatzteile oder Teile mit den gleichen Charakteristiken wie die ursprünglichen Teile verwendet. Unautorisierte Ersatzteile können Feuer, elekt rischen Sc hlag oder sonstige Gefährdungen verursachen. 22. Sicherhe ...

  • Hitachi CU-HD1000 - page 9

    G MISES EN GARDE IMPORTANTES 1. Lire les instructions Lire toutes les instructi ons de sécurité et de fonctionneme nt avant de faire fonctionner l’appareil. 2. Conserver ces instructions Conserver les instructions de sécuri té et de f onctionnement á des fi ns de référence ultérieure. 3. Tenir compte des avertissements Tous les avertissem ...

  • Hitachi CU-HD1000 - page 10

    H 14. Foudre Pour renforcer la protection de l’a ppareil pendant un orage, ou si l’on s’en éloigne ou qu’on rest e longtemps sans l’utiliser, le débrancher de la source d’ alimentation. Ceci permettra d’éviter t out dom mage de l’appareil dú á la foudre et aux surtensions de ligne. 15. Surcharge Ne pas surcharger les prises, ra ...

  • Hitachi CU-HD1000 - page 11

    Contents Outline and f eatures ··································································································· 1 Warnings and cauti ons when us ing ·········································? ...

  • Hitachi CU-HD1000 - page 12

    1 Outline and features The CU-HD1000 is a camera control unit (CCU) for the newly developed multi-standard camera SK- HD1000. The CU-HD1000 is c ompact (half rack/3 units), lightweight (7kg approx.), and provides significantly reduced powe r consumption and improved operability. HD-SDI ( 1080i/720p ) input/output is mounted as standard. A flexi ...

  • Hitachi CU-HD1000 - page 13

    2 Warnings and cautions when using CAUTION  Do not disassemble or modify Th e camera contains precision internal components. Do not open the cover or disturb switches and controls other than designated. There is risk of impaired performance and damage.  Keep foreign object out of interior Entry of water, metallic or other foreign materials ca ...

  • Hitachi CU-HD1000 - page 14

    3 Warnings and cautions when using Hybrid Fiber Optical Camera Cable & Connector Handling CU-HD1000 camera is using the optical fiber cab le & connector which is required special technique for handling. 1. Cable Connector & Receptacle (1) FCF (Fiber Cable Female) (2) FCM (Fiber Cable Male) (3) FCFR (Female Receptacle) (4)FCMR (Male Rece ...

  • Hitachi CU-HD1000 - page 15

    4 Facility names and functions 1 CCU POWER switch CCU power on/off switc h. 2 CCU POWER LED Lights when power is on. 3 CABLE CHECK LED OK: CAMERA POWER switch 4 can be operated. OPEN: Fiber cable not connected. SHORT: Excess current in fiber cable. Note: CAMERA POWER switch 4 is inoperative when OPEN, SHORT LED is lighted. 4 CAMERA POWER sw itch Ca ...

  • Hitachi CU-HD1000 - page 16

    5 Facility names and functions 13 HD SDI OUT connectors (BNC) Outputs three lines of digi tal serial HDTV video signals. 14 HD/SD SDI connectors (BNC) Outputs four lines of digit al serial HDTV/SDTV video signals. Select the HD-SDI or SD-SDI by the user function menu. The character is superimposed in PIX output. 15 D.RET input connectors (BNC) Inpu ...

  • Hitachi CU-HD1000 - page 17

    6 Facility names and functions 23 Genlock connectors (BNC) Input for tri-level sy nc signal or black burst signal for genlock operation. 24 AC IN connector Input for AC power supply. 25 FG terminal Frame ground term inal. 26 Fiber connector Connect Fiber cable. 27 Receiver Level LED The strength of the arriving li ght signal via fiber cable is indi ...

  • Hitachi CU-HD1000 - page 18

    7 Function menu Function menu Use the ca mera control panel or the setup cont rol unit co nnected to the C U-HD1000 rear side t o display the function m enus. The function menus include the CCU menu to set the CU-HD1000 and the camera menu to set a camera. (And also the func tion menus contro l the button of the TU-SD.Di gital unit insid e the CU-H ...

  • Hitachi CU-HD1000 - page 19

    8 Function menu CCU menu If the F UNC button of the cam era control panel is pre ssed with the color bar ON, the CC U menu is displayed. Camera menu The camer a menu appe ars when the co lor bar is off. Cont ents differ by the camera. Refer to the ca mera operating in structions. ■RETURN SELECT RE T . C H SE L E C T CH1 :D.RET1 CH2 :D.RET2 CH3 :A ...

  • Hitachi CU-HD1000 - page 20

    9 Function menu CU-FUNCTION menu TV FORMAT menu NOTICE : The cursor is moved to an arbi trary format with an upper an d lower swit ch, and when TV FORMAT is set, a right a nd left switch is operate d, and set. The ☑ mark is disp layed by pushing a righ t and left switch, an d TV FORMAT is changed. After TV FORMAT is set, it saves th ...

  • Hitachi CU-HD1000 - page 21

    10 Function menu TIME/DATE menu ■TIME/DATE DATE DISP :Y.M.D TIME DISP :ON YEAR : 0 8 MONTH : 0 1 D A Y : 0 1 HOUR : 1 2 MINUTE : 0 0 SET DATA :PUSH + Item Setting Factory setting D ...

  • Hitachi CU-HD1000 - page 22

    11 Function menu RETURN SELECT menu ASSIGNMENT menu MIC GAIN menu ■RETURN SELECT RET.CH SELECT C H 1 :D.RET1 C H 2 :D.RET2 C H 3 :A.RET1 C H 4 :A.RET2 ASSIGNMENT : ■ASSIGNMENT ...

  • Hitachi CU-HD1000 - page 23

    12 Function menu SYSTEM TIMING menu PIX DISPLAY menu SD-DTL menu ■SD DTL S D D T L : O N H GAIN : 0 V GAIN : 0 H CRISP :-128 V CRISP :-128 DTL FREQ :5MHz LEVEL DEP :-128 LEL DEP SLP? ...

  • Hitachi CU-HD1000 - page 24

    13 Function menu SD-SETTING menu ECC filter indica tion When the FILTER setting is ON, the ECC filter is displayed at th e lower center of the screen. The display depends on the optica l filter position. ECC_FILTER A.3200K B.4300K C.5600K D.6300K E.8000K Displays ECC filter information with optical filter 1. PIX OUT camera status display 1.3? ...

  • Hitachi CU-HD1000 - page 25

    14 Cable check Cable check LED lights when cable is connected. For safety, the camera power defa ults to off according to the res ult. Indica tion Conte nt Screen : CHECK CAMERA CABLE CAMERA CABLE SHORT LED : SHORT lights The power line may be short-circuited. Camera power defaults to off and camera power switch is r endered inoperative. Screen ...

  • Hitachi CU-HD1000 - page 26

    15 Warning indication Indica tion Conte nt Screen : CCU FAN ALARM !! FA N warning of CCU The internal fan is stopped or the rotating speed is lowered. If the fan alarm is i ndicated, the system should be re paired immediately. ...

  • Hitachi CU-HD1000 - page 27

    16 Backup battery replacement Backup battery replacement The backup battery is already i nstalled at the factory. If the time/ date information no longer appears, set the power switch to on. If the PIX OUT shows “ BACKUP BATT EMPTY ” for about 6 seconds, the batte ry needs to be replaced. And the date and time need to b e set at the TIME/DATE m ...

  • Hitachi CU-HD1000 - page 28

    17 System Configuration ...

  • Hitachi CU-HD1000 - page 29

    18 PUSH 1 2 3 Service information Connector pin diagrams INTERCOM (5 pin XLR female:HA16PRH-5S) MI C OUT 1,2 (3 pin XLR male:HA16RM-3SE) Remote 1,2 (4 pin female:HR10A-7R-4S(73)) Combined connector: HR10A-7P-4P TALLY OUT(9pin D-sub female :RDED-9S-LNA(4-40)(55)) 1 5 96 Application circuit example Plug CU mainframe Internal circuit Pin Signal 1 TALK ...

  • Hitachi CU-HD1000 - page 30

    19 Service information COMMUNICATION (25pin D-sub ma le:RDBD-25P-LNA(4-40)(55)) 11 3 14 25 P l u g CU mainframe Contact supply Voltage supply P i n 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Pin Signal 1 SYS2 2 SYS1 3 SYS0 4 PD OUT (C) 2W : OUT/IN(C) 5 PD OUT (H) 2W : OUT/IN(H) 6P D S H I E L D 7 PD IN (C) 2W : NC 8 PD IN (H) ...

  • Hitachi CU-HD1000 - page 31

    20 Service information MIC REMOTE (15pin D-sub female: RDAD-15S-LNA(4-40)(55)) 81 15 9 P l u g C U m a i n f r a m e + 5 V S W O N : L o S W O F F : H i Hi : Internal Control (Menu) MIC SEL Lo : External Control (MIC REMOTE connector) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin Signal 1 +5V OUT (200mA max) 2 TALLY GND 3 G TALLY OUT 4 R ...

  • Hitachi CU-HD1000 - page 32

    21 5 1 11 6 10 15 Service information RS-232C(9pin D-sub male: RDED-9P-LNA(4-40)(55)) P l u g CU mainframe 5 1 69 *RTS:Request To Send *CTS:Clear To Send WFM CONTROL (15pin female:YKF42-8043N) P l u g CU mainframe Pin Signal 1 NC 2 RX_232C (IN) 3 TX_232C (OUT) 4 NC 5 GND 6 NC 7 RTS (OUT) 8 CTS (IN) 9 NC P i n 1 2 3 4 5 6 7 8 9 Pin Signal 1 2 WFM CT ...

  • Hitachi CU-HD1000 - page 33

    22 Service information Intercom system setting TU-D.SD-DIGITAL Board SW12~15 2 wire 4 wire SW16 –No.2 1 2 3 4 O N RT S Clear com ...

  • Hitachi CU-HD1000 - page 34

    23 Service information Video frame rate setting The CU-HD1000 is switchable for video fr ame rate between 59.94 Hz and 50 Hz. The setting method is offered by the dip sw itch SW16–No.4 on TU-D.SD-DIGITAL board. When the dip switch SW16–No.4 is turned ON, the video frame rate can be switched by the dip switch SW16–No.1. Dip switch setting on T ...

  • Hitachi CU-HD1000 - page 35

    24 External View CU-HD1000 External View Unit:mm ...

  • Hitachi CU-HD1000 - page 36

    25 Specifications y Power supply voltage CU-HD1000J AC100V 50/60Hz CU-HD1000U AC117V 60Hz CU-HD1000E AC230V 50Hz y Power consumption 210W approx. (AC operati on, including SK-HD1000,VF-402 and utility POWER) y Ambient Temperature Operating: 0 to +40 ℃ Storage: -20 to +60 ℃ y Dimensions 216(W) ° 118(H) ° 400(D)mm y Mass 7kg approx. y Max. Cabl ...

  • Hitachi CU-HD1000 - page 37

    26 Specifications Output signals DIGITAL OUT HD-SDI(1080i,720p) (Embedded audio availa ble) ・ 1080i:SMPTE292M 0.8Vp-p/ 1.5Gbps ・ 720p:SMPTE296M 0.8Vp-p/1.5Gbps BNC (x3) HD-SDI(1080i,720p) or SD-SDI selectable (Embedded audio availa ble) ・ 1080i :MPTE292M 0.8Vp-p/1.5Gbps ・ 720p:SMPTE296M 0.8Vp-p/1.5Gbps ・ SD-SDI:SMPTE259M 0.8Vp-p/270M bps ...

  • Hitachi CU-HD1000 - page 38

    27 Specifications ■ Accessories ・ Camera control panel Base station internal/external d ual type External base station dedicat ed type ・ Setup control unit ■ Standard Composition ・ Camera Control Unit : CU-HD1000 1 ・ Code Set(U/J) : WC0051(0234-0089A 2.5M) (8488057) 1 ・ Code Set(E) : VM0306B;VM0303B 2.5M (BBZ0399) 1 ・ Fuse(U/J) : UL ...

Manufacturer Hitachi Category Camera Lens

Documents that we receive from a manufacturer of a Hitachi CU-HD1000 can be divided into several groups. They are, among others:
- Hitachi technical drawings
- CU-HD1000 manuals
- Hitachi product data sheets
- information booklets
- or energy labels Hitachi CU-HD1000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hitachi CU-HD1000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hitachi CU-HD1000, service manual, brief instructions and user manuals Hitachi CU-HD1000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hitachi CU-HD1000.

Similar manuals

A complete manual for the device Hitachi CU-HD1000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hitachi CU-HD1000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hitachi CU-HD1000.

A complete Hitachi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hitachi CU-HD1000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hitachi CU-HD1000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hitachi CU-HD1000, that we can find in the current document
3. Tips how to use the basic functions of the device Hitachi CU-HD1000 - which should help us in our first steps of using Hitachi CU-HD1000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hitachi CU-HD1000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hitachi CU-HD1000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hitachi CU-HD1000?

Use the form below

If you did not solve your problem by using a manual Hitachi CU-HD1000, ask a question using the form below. If a user had a similar problem with Hitachi CU-HD1000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)