English dropdown-ico

Manual Agilent Technologies 87020

268 pages 2.65 mb
Download

Go to site of 268

Summary
  • Agilent Technologies 87020 - page 1

    Agilent 8702D Lightwave Component Analyzer Installation Guide ...

  • Agilent Technologies 87020 - page 2

    ii © Copyright Agilent T echn ologies 2000 All Rights Reserved. Repro- duction, adaptation, or trans- lation w ithout prior writ ten permi ssion is proh ibited, except as allowed under copy- right laws. Agilent P art No . 08702- 9005 5 Printed in U SA Apri l 2000 Agilent T echnolo gies Lightwave Division 1400 Fountaingrove Parkway Sant a Rosa, CA ...

  • Agilent Technologies 87020 - page 3

    iii Insta llation at a G lance Installation at a Glance The proced ures in this b ook provid e step-by -step in struction s for instal ling the A gilent 8702D . Be sure to verify t he Agilent 8702 D’ s performance Chapter 2, “ Automa ted V e rificatio n ” , Chapter 3 , “ Manual V erifi cation ” , and Chapter 4, “ Performan ce T ests ” ...

  • Agilent Technologies 87020 - page 4

    iv Gener al Sa fety Co nsid era tions General Safety Considerat ions This product has been designed and tested in accordance with IEC Publica- tion 61010-1 , Safety Requir ement s for Electrical Eq uipment for Measurem ent, Contro l and Laborato ry Use, and has been supplie d in a safe co ndition. The instruction d ocumentation co ntains info rmati ...

  • Agilent Technologies 87020 - page 5

    v Certifica tion CAUTIO N Before s witching on this instrument , make sure that the l ine voltag e selec tor swit ch is set t o the lin e voltage o f th e power sup ply a nd the co rrect fuse is inst a lle d. Assur e the supply vol tage is in the spec ified rang e. CAUTIO N This pro duct is desi gned for use in In stallatio n Category II and Poll u ...

  • Agilent Technologies 87020 - page 6

    vi Assistan ce Assis tance Product maintenance agreements and other customer assistan ce agreements are avai lable for Agil ent T echnologies produ cts. Fo r any assi stance, cont act your nearest Agi lent T ec hno logies Service Office. ...

  • Agilent Technologies 87020 - page 7

    Contents Contents-1 1 Installi ng the Agile nt 8702D Step 1. Insp ect t he Ship ment 1-3 Step 2. Set up St atic-S afe W orksta tion 1-4 Step 3. Opt ion 1D5, Conne ct the Frequ ency Refer ence 1-6 Step 4. Che ck the Fuse and V olta ge Sele ction 1-7 Step 5 . Connect the L i ne-Power Cable 1-9 Step 6 . Connect a Keyboard 1-10 Step 7. T urn on th e Ag ...

  • Agilent Technologies 87020 - page 8

    Conte nts -2 Conte nts 9. Calibr ation Coeffi cients 4-34 10. Syste m T race Noise (Only for Analyze rs with out Opti on 006) 4 -40 11. Syste m T race Noise (Only for Analyze rs with Option 00 6) 4-4 2 12. T est Port Input Imped ance 4-44 13. T est Port Receiver Magnitude D ynamic Accura cy 4-48 14. T est Port Receiver Phase Dynamic A ccuracy 4-55 ...

  • Agilent Technologies 87020 - page 9

    Contents-3 Conten ts 9. Receiver Inp ut Crosstalk 6-26 10. Receiver T race Noise 6-33 11. Receiver In put Impedance 6-35 12. Receiver Magnitude Dynamic Accuracy 6-39 13. Receiver Phase Dynamic Accuracy 6-47 14. Receiv er Magn itude Compre ssion 6-4 8 15. Receiver Phase Compr ession 6-56 16. Source and Receive r Harmonics (O ption 002 Only) 6-62 17. ...

  • Agilent Technologies 87020 - page 10

    ...

  • Agilent Technologies 87020 - page 11

    1 Step 1. Insp ect th e Ship ment 1-3 Step 2. Set up St atic-S afe W orksta tion 1-4 Step 3. Opt ion 1D5, Conne ct the Frequ ency Refer ence 1-6 Step 4 . Check the Fuse and V oltage Selec t ion 1-7 Step 5 . Connect the L i ne-Power Cable 1-9 Step 6 . Connect a Keyboard 1-10 Step 7. T urn on th e Agilent 870 2D 1-11 Step 8. Connect a Prin ter or Plo ...

  • Agilent Technologies 87020 - page 12

    1-2 Instal ling the Agil ent 8702D Instal ling the Agile nt 8702 D Installing the Agilent 8702D The instr uction s in this chapter show y ou how to inst all your Ag ilent 8702 D. Y ou sho uld be abl e to fini sh these p rocedures in about ten to twenty minut es. Refer to “ Specific ations and Regul atory Inf ormation ” , in the Agilent 8702D Re ...

  • Agilent Technologies 87020 - page 13

    1-3 Installi ng the Agile nt 8702D Step 1 . Inspect the Shipment Step 1. Inspect the Shipment 1 Verify t hat all components or dered have arrived by comparing the ship ping forms to the ori ginal purchase order. Ins pect all shippi ng containe rs. If you r shipment is damaged or incompl ete, save the pa cking mate rials and no- tify bo th the sh ip ...

  • Agilent Technologies 87020 - page 14

    1-4 Instal ling the Agil ent 8702D Step 2. Set up Sta tic-Safe Wo rkstation Step 2. Set up Static-Safe Workstation Electro static d ischarge (ESD ) can dama ge or des troy th e input cir cuits of the Agilen t 8702D. E SD can also damage or d estroy elect ronic compo nents tha t you are measuri ng. All work should be per formed at a static-safe work ...

  • Agilent Technologies 87020 - page 15

    1-5 Installi ng the Agile nt 8702D Step 2. Set up Sta tic-Safe W orkstatio n Both typ es, when use d toge ther , provid e a sig n ific ant l evel of ESD pro tection. Of th e two, o n ly t he ta ble-mat and wr ist-stra p co mbin ation pro v id es ade quate ESD p rotect ion wh en used alon e. T o en sure use r safety , the s tatic-safe access ories m ...

  • Agilent Technologies 87020 - page 16

    1-6 Instal ling the Agil ent 8702D Step 3. Opt ion 1D5, Connec t the Freq uency Reference Step 3. Option 1D5, Connect th e Frequency Reference If your inst rument has the opti onal high st abilit y freque ncy refer ence insta lled, conn ect t he jumpe r cable on the Ag ilent 8702D re ar panel as show n in Figure 1-2 . Figure 1-2. Jumper Cable Conne ...

  • Agilent Technologies 87020 - page 17

    1-7 Installi ng the Agile nt 8702D Step 4. Check the Fuse an d V o lt age Sele ction Step 4. Check the Fuse and Voltage Selection 1 Locat e the line-input c onn ector o n th e inst rument ’ s rear pa nel. 2 Discon nect the l ine-power ca ble i f it is co nnected. 3 Use a small flat-blade screwdriv er to open the p ull-ou t fu se dra wer. WAR NI N ...

  • Agilent Technologies 87020 - page 18

    1-8 Instal ling the Agil ent 8702D Step 4. Ch eck the Fu se and Volt age Selec tion WAR NI N G For con tinued protec tion again st fire h azard, re place l ine fuse on ly with same ty p e and rat ings, (type T 3A/ 250V for 100/2 40V operation). The use of o ther fu ses or materi als is pr ohibi ted. 5 Set the rea r panel line -voltag e select or to ...

  • Agilent Technologies 87020 - page 19

    1-9 Installi ng the Agile nt 8702D Step 5. Co nnect the L ine-Power Cable Step 5. Connect the Line-Power Cable CAUTIO N Always use the thre e-prong AC power cord sup p lie d with thi s instrument . Failur e to ensu re adequat e earth gro unding by not using thi s cord may caus e instru ment damag e. CAUTIO N Do not connect ac power until you have v ...

  • Agilent Technologies 87020 - page 20

    1-10 Instal ling the Agil ent 8702D Step 6. Co nnect a Key board Step 6. Connect a Keyboard • If y o u pl a n to use a keyboard with your Agil ent 8702D, connec t it now to the instr ument ’ s rear-panel k eyboard conne c tor . Figure 1-6. Rear Panel Peri pheral Connections ...

  • Agilent Technologies 87020 - page 21

    1-11 Installi ng the Agile nt 8702D Step 7. T urn on th e Agilent 87 02D Step 7. Turn on the Agilent 8702D 1 Press th e front-pa nel LINE key. Refe r to Fig ure 1-7 . The f ront-panel LINE switch di sconnects the mai ns circui ts from the mai ns sup- ply af ter t he EMC filt ers and before othe r parts of the in strume nt. 2 If th e Agilent 8 702D ...

  • Agilent Technologies 87020 - page 22

    1-12 Instal ling the Agil ent 8702D Step 8 . Connect a Printer or Plotte r Step 8. Connect a Printer or P lotter 1 Connect a print er or plotte r to the cor responding interface port. Refer to Figure 1-6 on page 1-10 for the appr opriate re a r pan el connect ion. 2 If yo u are u sing th e parallel i nterface, p ress LOCAL and then PA RA L L EL un ...

  • Agilent Technologies 87020 - page 23

    1-13 Installi ng the Agile nt 8702D Step 9. If Y ou Co nnect a Pri nter Step 9. If You Connect a Printer 1 Press LOCAL , SET ADDRESSES , PRINTER PORT . 2 Press th e key that corre sponds to the p rinter inte rface: HPIB , PA R A L L E L (pa ralle l port), or SERIAL (seria l port). 3 If you sel ected HPIB , the GPIB ad dress is active s o you can t ...

  • Agilent Technologies 87020 - page 24

    1-14 Instal ling the Agil ent 8702D Step 10. If Yo u Connec t a Plot ter Step 10. If You Connect a Plotter 1 Press LOCAL , SET ADDRESSES , PLOTTER PORT . 2 Press t he key that co rresp o nds t o the p lott er interfac e: HPIB , PA R A L LE L (parallel port), or SERIAL (seria l port). 3 If you sel ected HPIB , the GPIB ad dress is active s o you can ...

  • Agilent Technologies 87020 - page 25

    1-15 Installi ng the Agile nt 8702D Step 11. Set the C lock Step 11. Set the Clock 1 Press SYSTEM , S ET CLOCK to begin setting and activating the time stamp feature so t h e A gilent 8702 D pl aces the t ime and d ate o n your har dcopies and disk director ies. 2 Press the appr opriat e softke y to s et the tim e and date . 3 Press ROUND SECONDS w ...

  • Agilent Technologies 87020 - page 26

    1-16 Instal ling the Agil ent 8702D Step 12. Chec k the Ope rati on Step 12. Chec k the Ope ration If yo ur in strument i s an Agilent 87 02D Op tion 0 11, s kip this st ep and con tinu e with “ Step 13. Check the Operatio n (Optio n 011) ” on page 1- 21 . 1 Turn off the LINE power switc h. Then , turn ba ck on the LINE pow er swi tch . 2 Locat ...

  • Agilent Technologies 87020 - page 27

    1-17 Installi ng the Agile nt 8702D Step 12. Check t he Oper ation Figure 1-10. Operation Check Connections 5 Press PRESET , SYSTEM , SERVICE MENU , TESTS , EXTERNAL TESTS , EXECUTE TEST . 6 Follow th e prompts shown on the display, and then pr ess CO NTIN UE . 7 Press th e up-arrow key, EXECUTE TEST , and then follow the pro mpts shown on the dis ...

  • Agilent Technologies 87020 - page 28

    1-18 Instal ling the Agil ent 8702D Step 12. Chec k the Ope rati on Figure 1-11. Transmission Mod e Conne ctions 9 Press CHAN 2 to check the forward transmi ssion mode for channel 2. Look at the measurem ent trace disp layed on the Agilen t 8702D . It should b e similar to the trace shown in Figur e 1-12 . The A gilent 8702D displ ay sh own in Figu ...

  • Agilent Technologies 87020 - page 29

    1-19 Installi ng the Agile nt 8702D Step 12. Check t he Oper ation Figure 1-13 . Figure 1-13. Reverse Transmission Display 11 Connec t t he equ ipm ent as show n in Figure 1-14 and pr ess PRESET . Figure 1-14. Transmission Load Match C onnections 12 Look at the meas urement tr ace display ed on the Ag ilent 8702D. It should be simila r to the tra c ...

  • Agilent Technologies 87020 - page 30

    1-20 Instal ling the Agil ent 8702D Step 12. Chec k the Ope rati on Figure 1-15. Forward T ransmission Mode 13 Press MEAS, Refl: E S22 REV to c heck the r evers e reflect ion mode fo r ch annel 1. The me asuremen t trace should be s i milar to Figure 1-16 . Figure 1-16. Reverse Ref lection Mode 14 Continual wi th “ Step 14. Copy the EEPRO M Disk ...

  • Agilent Technologies 87020 - page 31

    1-21 Installi ng the Agile nt 8702D Step 1 3. Check t he Opera tion (Op tion 011) Step 13. Check t he Operation (Option 011) An Agi lent 8 5047A S-paramete r test se t must be us ed when making meas ure- ments. 1 Turn off the LINE power switc h. Then , turn ba ck on the LINE power switc h . 2 Locate the ser ial numbe r and configur ation opti ons s ...

  • Agilent Technologies 87020 - page 32

    1-22 Instal ling the Agil ent 8702D Step 13. Chec k the Ope ration (Opti on 011) Figure 1-18. Operation Check Connections 5 Press PRESET , SYSTEM , SERVICE MENU , TESTS , EXTERNAL TESTS , EXECUTE TEST . 6 Follow the prompts show n on t he dis play, a nd the n pr ess CON TINUE . 7 Press th e up-arrow key, EXECUTE TEST , and then fo llow the promp ts ...

  • Agilent Technologies 87020 - page 33

    1-23 Installi ng the Agile nt 8702D Step 1 3. Check t he Opera tion (Op tion 011) Figure 1-19. Transmission Mod e Conne ctions 9 Press CH2 to check the forward tr ansmission m ode for channel 2. Look at the measu rement trace displ ayed on t he analyzer. It sho uld be s imilar to the trace shown in Fig ure 1-20 . The an alyzer dis play sh o wn i n ...

  • Agilent Technologies 87020 - page 34

    1-24 Instal ling the Agil ent 8702D Step 13. Chec k the Ope ration (Opti on 011) 10 Press MEA S and then T rans: E/E S12 REV to check t he reverse transmis sion mode for channel 2 . The measure ment trace sh ould be similar to the trace sh own in Figure 1-21 . Figure 1-21. Reverse Transmission Display 11 Connec t t he equ ipm ent as show n in Figur ...

  • Agilent Technologies 87020 - page 35

    1-25 Installi ng the Agile nt 8702D Step 1 3. Check t he Opera tion (Op tion 011) Figure 1-23. Forward T ransmission Mode 13 Press MEAS , Refl: E S22 REV to check the reve rse ref lection mo de for cha nnel 1. The me asuremen t trace sho uld be simila r to Figure 1-24 . Figure 1-24. Reverse Re flection M ode ...

  • Agilent Technologies 87020 - page 36

    1-26 Instal ling the Agil ent 8702D Step 14. C o py th e EEPROM Disk Step 14. Copy the EEPROM Disk The A gilent 87 02D is ship ped from t he facto ry wit h an EEPROM backup di sk which is unique to each instrume nt. The backup disk contains a copy of cor- rect ion c onst ants whic h wer e st ored in the ins trumen t ’ s internal memor y at the f ...

  • Agilent Technologies 87020 - page 37

    2 Step 1. I nitial iza tion 2-3 Step 2 . Measu rement Calibra tion 2-4 Step 3. Device Ve rification 2-6 In Case of Difficul ty 2-9 Automa ted Verifi cation ...

  • Agilent Technologies 87020 - page 38

    2-2 Automated V erification Automate d Performan c e Verifica tion Automated Performance Verification The auto mate d perfor mance ve rificati on proce dure in this chapt er provi de a high level of c onfiden ce that t he Agilent 8702D is wo rking proper ly . Althoug h this procedure is automa ted, it does not require a comput er . How eve r , you ...

  • Agilent Technologies 87020 - page 39

    2-3 Automated V e rification Step 1. Initializatio n How to select the s y stem veri fication procedure Check to see how th e verif ication kit fl oppy disk is la bele d: • If t he di sk is lab eled V e rification Da ta Disk , pr oceed with the Ag ilent 8702 D Auto- mated Mode System Ve rifica tion in th is chapter. • If th e disk i s labeled V ...

  • Agilent Technologies 87020 - page 40

    2-4 Automated V erification Step 2. Me asurement Calibration 3 Insert the verificat ion kit disk into the Ag ilent 87 02D ’ s disk dr ive. 4 Press PRESET , SAVE/REC ALL , SELECT DISK , INTERNAL DISK . 5 If you w ant a printou t of t he verifi cation data for all the devices, p ress SYSTEM , SERVICE MENU , TEST OPTIO NS , RECORD ON . If you swi tc ...

  • Agilent Technologies 87020 - page 41

    2-5 Automated V e rification Step 2. Meas urement Cali bration Figure 2-2. Connections f or Mea surement Cal i bration Standards 5 Press F ORW ARD:OPEN . 6 When the A gilent 8 702D finis hes measur ing the st andard, conne ct the “ short ” end of the open /short comb ination to refe rence tes t port 1 . 7 Press F ORWARD:SHORT . 8 When t he Agil ...

  • Agilent Technologies 87020 - page 42

    2-6 Automated V erification Step 3 . Device Ve rificat ion 17 Con nect th e test port c ables as sho wn Figur e 2-3 . Figure 2-3. Transmission Cali b ration Setup 18 Press TR ANSM ISSION , F WD TRANS THRU . 19 When the Agilen t 8702D f inishe s the measureme nt, pre ss FWD MA TCH THRU . 20 When the Agilen t 8702D f inishe s the measureme nt, pre ss ...

  • Agilent Technologies 87020 - page 43

    2-7 Automated V e rification Step 3. De vice V erification each S -paramete r meas ureme nt. • If you switch ed the record functi on on , the Agilent 8702D measur es all S-pa - ramet ers (magn itude and phas e) w it hout pau sing. Also, the Agilen t 8702D only di splays and pri nts the pass /fail in formatio n for the S-paramete r me a- surements ...

  • Agilent Technologies 87020 - page 44

    2-8 Automated V erification Step 3 . Device Ve rificat ion of the verification mi smatch t o refere nce test p ort 1. Figure 2-6. Mismatch Devic e Verificati on Setup 7 Press RETURN , TESTS , 30, x1 , EXECUTE TEST , CONTINUE . 8 When t he Agil ent 8 702D fini shes a ll th e measu rements, c onnec t the mismatch verification de vice, as shown in Fig ...

  • Agilent Technologies 87020 - page 45

    2-9 Automated V e rification In Case of Difficulty 10 You h ave com pleted the sy stem verifi cation proc edure when th e Agilent 8702D disp lays, Ver Def 4 DONE . In Case of Difficulty 1 Inspect all conne ctions. Do not dis connect th e cable s from the A gilent 8 702D test ports. Doi n g so will inval idate the ca libr ation that you ha ve done e ...

  • Agilent Technologies 87020 - page 46

    ...

  • Agilent Technologies 87020 - page 47

    3 Step 1. I nitial iza tion 3-2 Step 2 . Measu rement Calibra tion 3-4 Step 3. Device Ve rification 3-5 In Case of Difficul ty 3-9 Manual Veri ficati on ...

  • Agilent Technologies 87020 - page 48

    3-2 Manual Veri fication Manual Per formance Verificat ion Manual Performance Verification The manual perform ance verificati on procedur e in this chapt er provide s a high le vel of confide nce that the Agi lent 8 702D is workin g properly . If yo u can locat e the Agil ent 8702D Verification D ata Disk , perform the automated vers ion in stea d, ...

  • Agilent Technologies 87020 - page 49

    3-3 Manual Verification Step 1. Initializatio n Figure 3-1. System Verification Test Setup 2 While the eq uipment is w a rmi ng up, r eview the conn ector care infor mation in the Agilent 870 2D User ’ s Gui de . 3 Set up the syst em to pr int the verifi cation data : a Press LOCAL , SYSTEM CONTR OLLER . b Press SET A DDRESSES , PRINTER PORT . c ...

  • Agilent Technologies 87020 - page 50

    3-4 Manual Veri fication Step 2. Me asurement Calibration CAUTIO N Do not press PRES ET or reca ll another instr ument state. Y ou must use the inst rument state tha t you loade d during the init ialization procedu r e. Step 2. Measurem ent Cali bration 1 Press MENU , POWER , – 2 , x1 to set the Agilen t 8702D t est po rt power t o – 2 dBm. 2 P ...

  • Agilent Technologies 87020 - page 51

    3-5 Manual Verification Step 3. De vice V erification 18 Con nect th e test por t cables toge ther as sh own in Figure 3-2 . Figure 3-2. Transmission Cali b ration Setup 19 Press TR ANSM ISSION , FWD TRANS THRU . 20 When t he Agil ent 8702 D fini shes mea surin g the standar d, pres s FWD MA TCH THRU . 21 When t he Agil ent 8702 D fini shes mea sur ...

  • Agilent Technologies 87020 - page 52

    3-6 Manual Veri fication Step 3 . Device Ve rificat ion Figure 3-3 . Figure 3-3. Connections for the 20 dB Verification Device 3 Press CONTINUE to run the test. 4 Press MENU , PO WER , –2 , x1 , CAL , CORREC TION ON . 5 Press COPY , PRINT MONOCHROME to obtain th e graphical represen tatio n of the measurem ent. 6 Press COPY , LIST , PRINT ALL MON ...

  • Agilent Technologies 87020 - page 53

    3-7 Manual Verification Step 3. De vice V erification tude and pha se for t he four S-p aram eters). 10 When th e Agilent 8702D disp lays, Ver Dev 1 FAIL , pr oceed to th e next s tep only i f all the tested S-parame ter meas urements show a PASS st atus after yo u activate error corre ction i n Step 8 . Otherwi se, refer to “ In Case of Difficul ...

  • Agilent Technologies 87020 - page 54

    3-8 Manual Veri fication Step 3 . Device Ve rificat ion Figure 3-5. Mism atch Device Verific ation Setup 17 Press TESTS , 30 , x1 , EXECUTE TEST , CONTIN UE . Ignore the error mess age. 18 Press MENU , PO WER , – 2 , x1 , CAL , CORR ECTION ON . 19 Repeat Step 5 throu gh Step 8 u ntil yo u have mad e all the S- parame ter measurements for th e ver ...

  • Agilent Technologies 87020 - page 55

    3-9 Manual Verification In Case of Difficulty Figure 3-6. Mismatch Devic e Verificati on Setup 22 Press TESTS , 31 , x1 , EXECUTE TEST , CONTINUE . Igno re th e displaye d erro r message. 23 Press MENU , PO WER , – 2 , x1 , CAL , CORR ECTION ON . 24 Repeat Step 5 throu gh Step 8 u ntil you have made all the S- paramete r measurements for th e ver ...

  • Agilent Technologies 87020 - page 56

    3-10 Manual Veri fication In Case of Difficulty a Press PRESET , SAVE/REC ALL , SELECT DISK , I NTERNAL MEMORY , RETURN . b Use th e front panel kno b to highl ight t he calib ratio n you want to recall and press REC ALL STA TE . c Press MENU , TRI GGER MENU , CO NTINUOU S to t r igge r the co ntinu ous sweep s. d Con nect th e short to refe rence ...

  • Agilent Technologies 87020 - page 57

    4 1. Test Port Output Freq uency Range and Accuracy 4-3 2. Exter nal Sour ce Mode Frequency Range 4-5 3. Test Port Output Powe r Accuracy 4-6 4. Test Port Output Powe r Range and Line arity 4-8 5. Minimum R Channel Level 4-10 6. Tes t Port Input Noise Floor L evel 4-15 7. Test Port In put Fre quency Respons e 4- 19 8. Test Port Cr ossta lk 4-29 9. ...

  • Agilent Technologies 87020 - page 58

    4-2 Performanc e Tests Manua l Performa nce Tests Manual Performance Tests This chapter c ontain s procedur es which te st the elec tric al performa nce of the Agilent 8702D. If yo u are us ing an Agilent 8702D O ption 01 1, pe rform the tests in C hapte r 6, “ Performance T ests – Option 011 ” . Before s tartin g these procedure s, allow th ...

  • Agilent Technologies 87020 - page 59

    4-3 Performance T ests 1. T est P ort Ou tput Fre quenc y Rang e and Accu rac y WAR NI N G Any servi cing, adjustme nt, maintena nce, or re p air of this p r oduct must be per forme d only by qualified p ersonn el. Repai r infor mation provided in the In Cas e of Difficulty sectio ns o f this chap ter are provided for quali fied servi ce perso nnel ...

  • Agilent Technologies 87020 - page 60

    4-4 Performanc e Tests 1. Test P ort Outp ut Freq uenc y Range an d Accu racy Figure 4-1. Test Port Outpu t Frequency Ran ge and Accuracy Test Setup 2 Press PRESET , MEN U , CW F REQ . 3 Press 30 , k/m and w rite the frequency counter reading on th e “ Performance Test R ecord. ” 4 Repeat Step 3 for each inst rument fr equency li sted in t he ? ...

  • Agilent Technologies 87020 - page 61

    4-5 Performance T ests 2. Ex terna l Sou rce M ode Freque ncy Ra nge 2. External Source Mode Frequency Range Perfo rm this te st to ve rify that the analyzer ’ s refere nce chann el, input R, is capable of phase lockin g to a n ext ernal CW sig nal. Requi red Equipment Extern al Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 62

    4-6 Performanc e Tests 3. Test Port Output Power Accuracy 5 Check t o see if the anal yzer is phas e locki n g to the e xternal CW signal: • If the a nalyzer displ ays any phase lock err or messages, wr ite “ unlock ” in the “ Perform ance Test Re cord ” for the s et CW s ignal. • If the anal yzer does not displ ay any phase lo ck error ...

  • Agilent Technologies 87020 - page 63

    4-7 Performance T ests 3. T est Po rt Output Power Accuracy Procedure 1 Zero and cali brate the powe r meter. Fo r more in formatio n of how to perfo rm this task, re fer to the powe r meter operati ng manual. 2 Connec t t he equ ipm ent as show n in Figure 4-3 . Figure 4-3. Source Outp ut Power Accuracy Test S etup 3 Press PRESET . ...

  • Agilent Technologies 87020 - page 64

    4-8 Performanc e Tests 4. Tes t Port Out put Power Rang e and Li neari ty 4 Press MENU , CW FREQ , 300 , k/m . Set the calibration factor on the power meter for this CW frequency. 5 Write the power meter reading on the "Performance Tes t Record." 6 Repeat Step 4 and Step 5 fo r each CW fr equency list ed in the "Perfor mance Test R e ...

  • Agilent Technologies 87020 - page 65

    4-9 Performance T ests 4. T e st Port Output Power Ra nge an d Lineari ty serv ice manual for mor e infor matio n on how to do this task. 2 On the an alyzer, press PRESET , MENU , CW FREQ , 300 , k/m . Set th e po wer me ter calibrat ion factor for this CW fre quency. 3 Connec t t he equ ipm ent as show n in Figure 4-4 . Figure 4-4. Test Port Out p ...

  • Agilent Technologies 87020 - page 66

    4-10 Performanc e Tests 5. Minimum R Channel Level 6 Write the p ower mete r rea d ing i n the "Resu lts Me asured" colu mn on t he "Performance Test Record." 7 Calculate th e differe nce betwee n the analyzer te st port powe r (which appear s on the analyzer ’ s display) an d the power meter readin g. Write the re sult in th ...

  • Agilent Technologies 87020 - page 67

    4-11 Performance T ests 5. Minimum R Channel Level Requi red Equipment For 50 Ω Analyzers Adapter, APC-3.5 (m) to APC-7 . . . . . . . . . . . . . . . . . Ag ilent P/N 1250-1746 Cable, APC-7 24- inch . . . . . . . . . . . . . . . . . . . . . . . . . . Ag ilent P/N 8120-4779 For 75 Ω Analyzers (Option 075) Minimum Loss Pad, 50 Ω to 75 Ω . . . ...

  • Agilent Technologies 87020 - page 68

    4-12 Performanc e Tests 5. Minimum R Channel Level 8 If the ana lyzer di splays a phase loc k error mes sage, continu e increasing the test port power un til phase lock is achieved. 9 Write the test port pow er, th at is displ ayed on the a n alyzer , on the "Performance Test Record." 10 Repeat Step 5 throu gh Step 9 fo r the other CW fre ...

  • Agilent Technologies 87020 - page 69

    4-13 Performance T ests 5. Minimum R Channel Level CAUTIO N Loop the W8 cable around the A5 samp ler as shown in Figure 4-6 . Do not push the ca ble down next to th e A11 phase lock assemb ly . Figure 4-6. Flexible RF Ca ble Location 2 Using an ohmme ter, verify tha t the RF cable is not op en. In add ition , examine both the cable connectors - mea ...

  • Agilent Technologies 87020 - page 70

    4-14 Performanc e Tests 5. Minimum R Channel Level 3 Check t he R s a mpler by sub s titu ting i t with the B s ampler (A6). a Move ca ble W8 to t he B sampler (A6), as sho wn in Figu re 4-7 . Figure 4-7. Connectio ns for Substi tuting the R S ampler (A4) 4 Connec t t he equ ipm ent as show n in Figure 4-8 . Figure 4-8. Setup for Checking the R Sam ...

  • Agilent Technologies 87020 - page 71

    4-15 Performance T ests 6. T est Po rt Input Noise Flo or Level 5 Repeat the t est, but s elec t the B samp ler (A6) by pres sing MEAS , INP UT PORTS , B in St ep 2 . Use the followi ng sp ecifications: 300 kHz to 3 GHz < – 27 dBm 3 GHz to 6 GHz < – 22 dBm 6 If th e analyz er fails the te st, repl ace the A11 as sembly. 7 Verif y that the ...

  • Agilent Technologies 87020 - page 72

    4-16 Performanc e Tests 6. Test Port In put Noise Floo r Level 2 Press PRESET , MEN U , POWER , – 85 , x1 , STOP , 3 , G/n . 3 Press MEA S , INPUT PORTS , A , TESTPORT 2 , FORM A T , LIN MA G , SCALE REF , AUTO SCAL E . 4 Press MARKER FCTN , MARKER MODE MENU , ST A TS ON , ME NU , TRIGGER MENU , SINGLE . 5 When th e analyzer fi nishes t he sweep, ...

  • Agilent Technologies 87020 - page 73

    4-17 Performance T ests 6. T est Po rt Input Noise Flo or Level Power ( dBm ) = 20 * [log 10 ( linear magnitude mean value )] 17 Write this calculate d value on the "Performance Test Record." Port 2 Noise Floo r Level from 50 kHz to 3 GHz (IF B W = 3 kHz) 18 Press AV G , IF B W , 3 , k/ m to change the IF bandw idth to 3 kHz. 19 Press MEN ...

  • Agilent Technologies 87020 - page 74

    4-18 Performanc e Tests 6. Test Port In put Noise Floo r Level Port 1 Noise Floo r Level for 3 G Hz to 6 GHz (IF B W= 10 Hz) 34 Press MEAS , INPUT PO RTS , A , TESTPORT 2 . 35 Press MENU , TRI GGER MENU , SINGLE . 36 When t he analyze r finishes the sw eep, notice th e mean value. 37 Conver t the meas ured linear magn itude mean v alue to log magn ...

  • Agilent Technologies 87020 - page 75

    4-19 Performance T ests 7. T e st Port Input Frequenc y Response 7. Test Port Input Frequency Response Perfo rm this te st to exa mine the v ector sum o f al l test se tup error vect ors in both magnit ude and pha se change as a func tion of freq uency . Requi red Equipment For 50 Ω Analyzers Power Mete r . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 76

    4-20 Performanc e Tests 7. Test Port In put Frequenc y Respons e Figure 4-10. Setup for Power M eter Calib ration on T est Port 1 3 Press PRESET , ST AR T , 300 , k/ m . 4 Only for Analyzers with Option 006: Press STO P , 3 , G/n . 5 Press LOCAL , SYSTEM C ONTROLL ER . 6 Press SET ADDRESSES an d PO WER M TR until the analyze r shows the cor rect po ...

  • Agilent Technologies 87020 - page 77

    4-21 Performance T ests 7. T e st Port Input Frequenc y Response 8 Press MENU , NU MBER of POINTS , 51 , x1 . 9 Press PO WER , PW R RAN GE MA N to turn th e auto power rang e off. 10 Press PO RT POWER to uncoupl e the test port output power. 11 Press CAL , PWRMTR CAL . 12 Press LOSS/SENSR LI STS , CAL FA CTOR SENSOR A . Refer to the back of the pow ...

  • Agilent Technologies 87020 - page 78

    4-22 Performanc e Tests 7. Test Port In put Frequenc y Respons e a From t he sensor ca libration factor ent r ies menu, press ADD . b Press FREQUENC Y , 100 , k/m . If you make an entr y erro r, press ← and re-enter the correct value again. c Press CAL FACTOR , 96. 4 , x1 . d Press DONE to term inate t he first calibration factor data poin t entr ...

  • Agilent Technologies 87020 - page 79

    4-23 Performance T ests 7. T e st Port Input Frequenc y Response T est Port 2 Input Frequ ency Response from 300 kHz to 3 GHz 16 Connec t t he equ ipm ent as show n in Figure 4-11 . Figure 4-11. Test Port 2 Input Freq uency Response Test Se tup 17 Press MEAS , INPUT PO RTS , B . 18 Press SCALE REF , SCALE/D IV , 1 , x1 . 19 Press MARKER , MARKER 1 ...

  • Agilent Technologies 87020 - page 80

    4-24 Performanc e Tests 7. Test Port In put Frequenc y Respons e Power Meter Calibrati o n on Port 2 from 300 kHz to 3 G Hz 22 Connec t t he equ ipm ent as show n Fig ure 4-12 . Figure 4-12. Setup for Power M eter Calib ration on T est Port 2 23 Press MEAS , INPUT PO RTS , TESTPORT 2 . 24 Press CAL , PWRMTR CAL , ON E SWEEP , T AKE CAL SWEEP to sta ...

  • Agilent Technologies 87020 - page 81

    4-25 Performance T ests 7. T e st Port Input Frequenc y Response 25 When the anal yzer dis plays the me ssage , P OWER METER CALIBRATION SWEEP DONE , con nect the eq uipm ent as shown as in Figure 4-13 . Figure 4-13. Test Port 1 Input Freq uency Response Test Se tup T est Port 1 Input Frequ ency Response from 300 kHz to 3 GHz 26 Press MEAS , INPUT ...

  • Agilent Technologies 87020 - page 82

    4-26 Performanc e Tests 7. Test Port In put Frequenc y Respons e Figure 4-14. Setup for Power M eter Calib ration on T est Port 2 33 Press ST ART , 3 , G/n , STOP , 6 , G/n . 34 Press CAL , PWRMTR CAL . 35 Press LOSS/SENSR LI STS , CAL FA CTOR SENSOR B . Repeat St ep 10 to build a calibrat ion factor sensor table for the Ag ilent 8481A powe r sens ...

  • Agilent Technologies 87020 - page 83

    4-27 Performance T ests 7. T e st Port Input Frequenc y Response T est Port 1 Input Frequ ency Response from 3 GHz to 6 GH z 39 When the analyze r finis h es the c alibra tion sweep, connect the equip ment as shown in Fig ure 4-15 . Figure 4-15. Setup for T est Port 1 Input Frequency Response 40 Press MEAS , INPUT PO RTS , A . 41 Press MARKER , MAR ...

  • Agilent Technologies 87020 - page 84

    4-28 Performanc e Tests 7. Test Port In put Frequenc y Respons e Figure 4-16. Setup for Power M eter Calib ration on T est Port 1 45 Press MEAS , I NPUT PORTS , TESTPORT 1 . 46 Press CAL , PWRMTR CAL , ONE S W EEP , T AKE CAL SWEEP to start the power meter calibrat ion for output test p ort 1. T est Port 2 Input Frequ ency Response from 3 GHz to 6 ...

  • Agilent Technologies 87020 - page 85

    4-29 Performance T ests 8. T est Port Crossta lk Figure 4-17. Test Port 2 Input Freq uency Response Test Se tup 48 Press MEAS , INPUT PO RTS , B . 49 Press MARKER , MARKER 1 , MARKER FCTN , MARKER MODE MENU , MKR SEA RCH , SEARC H:M IN . 50 Press MARKER , MARKER 2 , MARK ER FCTN , MAR KER MODE MENU , MKR SEA RCH , SEARC H:MAX . 51 Write the marker ...

  • Agilent Technologies 87020 - page 86

    4-30 Performanc e Tests 8. Test Port C rosstal k Requi red Equipment For 50 Ω Analyzers Calibrati on Kit, 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt 85031B Cable, APC-7 24- inch . . . . . . . . . . . . . . . . . . . . . . . . . . . Ag ilent P/N 8120-477 9 For 75 Ω Analyzers Calib ration Kit, 75 Ω , Ty pe-N ...

  • Agilent Technologies 87020 - page 87

    4-31 Performance T ests 8. T est Port Crossta lk Crosstalk to T est Port 2 fr om 300 kHz to 3 GHz 4 Press ST ART , 300 , k/m , STO P , 3 , G/n . 5 Press MEAS , T rans: E/E S21 FWD . 6 Press SCALE REF , REFEREN CE V ALUE , – 100 , x1 . 7 Press MENU , TRI GGER MENU , SINGLE . 8 Press MARKER FCTN , MARKER MODE MENU , MKR SE ARCH , SEARCH: MAX . 9 Wr ...

  • Agilent Technologies 87020 - page 88

    4-32 Performanc e Tests 8. Test Port C rosstal k In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emoval of part s is likely to exp o se dangerous v oltag ...

  • Agilent Technologies 87020 - page 89

    4-33 Performance T ests 8. T est Port Crossta lk Figure 4-19. Agilent 8702D Bottom Vi ew ...

  • Agilent Technologies 87020 - page 90

    4-34 Performanc e Tests 9. Calibratio n Coefficients 9. Calibration Coefficients Perfo rm this pro cedure to ve rify the analyz er unc orrec ted te st port cha r act er- istic s. Requi red Equipment For 50 Ω Analyzers Calibrati on Kit, 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt 85031B Cable, APC-7, 24-in ch . ...

  • Agilent Technologies 87020 - page 91

    4-35 Performance T ests 9. Calibra tion Coefficients 2 Press PRESET , ST AR T , 300 , k/ m . 3 Press CAL , CAL KI TS & STDS , SELE CT CAL KI T , CAL KIT : 7mm , RETURN , RETURN , CALI BRA TE ME NU , FU LL 2 -PORT . 4 Press ISOLA TION , O MIT ISOLA TION , ISOLA TION DONE . 5 Con nec t the “ open ” end o f th e open/ s hort combi nation (supp ...

  • Agilent Technologies 87020 - page 92

    4-36 Performanc e Tests 9. Calibratio n Coefficients Figure 4-21. Transmission Cali bration Test Setup 19 Press TR ANSM ISSION , FW D TRANS TH RU . 20 When the analy zer fi nish es t he me asure ment, pres s FWD MA TCH THRU . 21 When the analy zer fi nish es t he me asure ment, pres s REV TRANS TH RU . 22 After the analyzer fi nishes the measur eme ...

  • Agilent Technologies 87020 - page 93

    4-37 Performance T ests 9. Calibra tion Coefficients T ransmission T racki ng (Forward) Calibration C oefficient 31 Press SYSTEM , SERVICE M ENU , TESTS , 37 , x1 , EXECUTE TEST . 32 When the analy zer fi nish es th e tes t, r epeat Step 25 throug h Step 2 8 . Reflection T racking (Forwar d) Calibration Coeffi cient 33 Press SYSTEM , SERVICE M ENU ...

  • Agilent Technologies 87020 - page 94

    4-38 Performanc e Tests 9. Calibratio n Coefficients 40 Press PRESET , ST AR T , 300 , k/ m . 41 Press CAL , CAL KI TS & STDS , SELE CT CAL KI T , CAL KIT : 7mm , RETURN , RETURN , CALI BRA TE ME NU , FU LL 2 -PORT . 42 Press ISOLA TION , OM IT ISOLA TION , IS OLA TION DONE . 43 Con nec t the “ open ” end o f th e open/ s hort combi nation ...

  • Agilent Technologies 87020 - page 95

    4-39 Performance T ests 9. Calibra tion Coefficients Figure 4-23. Transmission Cali bration Test Setup 57 Press TR ANSM ISSION , FW D TRANS TH RU . 58 When the analy zer fi nish es t he me asure ment, pres s FWD MA TCH THRU . 59 When the analy zer fi nish es t he me asure ment, pres s REV TRA NS THR U . 60 When the analy zer fi nish es t he me asur ...

  • Agilent Technologies 87020 - page 96

    4-40 Performanc e Tests 10. Syst em Trace N oise (O nly fo r Analyze rs withou t Opti on 006) Source Match (R everse) C alibratio n Coeffi cient 69 Press SYSTEM , SERVICE M ENU , TESTS , 39 , x1 , EXECUTE TEST . 70 When the analy zer fi nish es th e tes t, r epeat Step 63 throug h Step 6 6 . Refl ection T racki ng (R everse ) Calib rati on Coeff ic ...

  • Agilent Technologies 87020 - page 97

    4-41 Performance T ests 10. Sy stem T rac e Noise (Only for Ana lyzers withou t Option 006) 2 Press PRESET , MEN U , POWER , 5 , x1 . 3 Press RETURN , CW FREQ , 3 , G/ n , NUMBER of POINTS , 1601 , x1 . 4 Press MARKER FCTN , MARKER MODE MENU , ST A TS ON to activate th e instrume nt ’ s statistic fea ture. System T race Noise fo r A/R Magnitude 5 ...

  • Agilent Technologies 87020 - page 98

    4-42 Performanc e Tests 11. System Tra ce Noise (On ly for Analyze rs with Optio n 006) In Cas e of Difficulty 1 Perform the “ ADC Offset Correction Constants ” pr oced ure, locat ed in the “ Adjus tments a nd Correc tion Co nsta nts ” chapter of th e Agilent 8753D Service Guid e . 2 Repe at this per formance te st. 3 Suspec t the A10 Di gi ...

  • Agilent Technologies 87020 - page 99

    4-43 Performance T ests 11. Sy stem T race Nois e (Only for Analyz ers with Opt ion 006) 3 Press MARKER FCTN , MARKER MODE MENU , ST A TS ON to activate th e instrume nt ’ s statistic fea ture. System T race Noise for A /R Magnitude from 30 kHz to 3 GHz 4 Press MEAS , T rans: E/E S12 REV . 5 Press MENU , CW FREQ , 3 , G/n , TRI GGER MENU , NUMB E ...

  • Agilent Technologies 87020 - page 100

    4-44 Performanc e Tests 12. Test Port In put Imp edanc e disp lay, on the “ Perfo rmance Te st Record . ” System T race Noise for B/R Magnitu de from 3 GHz to 6 GHz 21 Press MENU , CW FREQ , 6 , G/n , TRI GGER MENU , NUMB ER of GR OUPS , 5 , x1 . 22 When t he anal yzer finishes the number of sw eeps, press SCAL E REF , AUTO SC ALE . 23 Write th ...

  • Agilent Technologies 87020 - page 101

    4-45 Performance T ests 12. T est Por t Input I mpeda nce Requi red Equipment For 50 Ω Analyzers Cable, APC- 7, 2 4-inch . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt P/N 8 120-477 9 Calibrati on Kit, 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt 85031B For 75 Ω Analyzers Cable, 75 Ω , Ty pe-N, 24- ...

  • Agilent Technologies 87020 - page 102

    4-46 Performanc e Tests 12. Test Port In put Imp edanc e 8 When the analy zer disp lays the prom pt, CONNECT STD THEN PRESS KEY TO MEASURE , connect a short to r eference test po rt 1. 9 Press F ORWARD: SHORT . 10 At the prom pt, connect a load to refere nce test por t 1. 11 Press F ORWARD: LOAD . 12 When th e analyzer di splays, ’ DONE ’ IF FI ...

  • Agilent Technologies 87020 - page 103

    4-47 Performance T ests 12. T est Por t Input I mpeda nce Figure 4-28. S22 1-Port Cal Test S etup 18 Press CAL , CALI BRA TE ME NU , S22 1-PORT . 19 At t he prom pt, connect an open t o ref eren ce te st po rt 2, as sho wn in Figure 4-28 . 20 Press REVERSE: OPEN . 21 When the analy zer disp lays the prom pt, CONNECT STD THEN PRESS KEY TO MEASURE , ...

  • Agilent Technologies 87020 - page 104

    4-48 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy Figure 4-29. Test Port 1 In put Impedance Test Setu p 28 Press MARKER to activate the analyzer ’ s marker 1. Use the fro nt panel knob to locat e the maximum value o f the data trace for eac h of the fr equency rang es liste d in the “ Performance Test Record. ” 29 ...

  • Agilent Technologies 87020 - page 105

    4-49 Performance T ests 13. T est Po rt Receiver Ma gnitude Dynamic A ccuracy Figure 4-30. Receiver Ma gnitude Dynamic Accur acy Requi red Equipment Measur ing Recei ver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agilen t 8902A Step Atte nuator, 110 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A gilen t 84 ...

  • Agilent Technologies 87020 - page 106

    4-50 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy Figure 4-31. Test Port 2 Dyn amic Accura cy Test Setup ...

  • Agilent Technologies 87020 - page 107

    4-51 Performance T ests 13. T est Po rt Receiver Ma gnitude Dynamic A ccuracy 5 On t he Agi lent 8 702D: a Press MEAS , INPUT PO RTS , B , MENU , POW ER , – 4 , x1 . b Using t he analyz er fro nt panel knob, adjust th e test por t pow er fo r a readi ng of – 20.000 dBm on the Agilen t 8902A. c Wait f or the r eading t o stabil ize. 6 On the Agi ...

  • Agilent Technologies 87020 - page 108

    4-52 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy T est Port 1 Magnitud e Dynamic Accuracy 15 Set the Agil ent 8496A to 10 dB. 16 On t he Agil ent 8 702D, pr ess CONTIN UOUS , MEAS , INPUT PORTS , TESTPORT 2 , A . 17 Connec t t he equ ipm ent as show n in Figure 4-32 . NOTE When the Agilent 8902A displays t he “ RECAL ...

  • Agilent Technologies 87020 - page 109

    4-53 Performance T ests 13. T est Po rt Receiver Ma gnitude Dynamic A ccuracy Figure 4-32. Test Port 1 Mag nitude Dynamic Acc uracy Test Setup 18 On t he Agi lent 8 702D: a Press MENU , PO WER . b Using t he analyz er fro nt panel knob, adjust th e test por t pow er fo r a readi ng of 0.000 dB on the Agil ent 8902A. c Wait f or the r eading t o sta ...

  • Agilent Technologies 87020 - page 110

    4-54 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy 19 On the Agi lent 8902A , press the blue shift ke y and SET REF . 20 On t he Agi lent 8 702D: a Press CAL , CALI BRA TE ME NU , RESPONSE , THRU . b After the analyzer fi nishes the measur ement, pres s DONE: RESPO NSE . c Press SAVE/R ECALL , SA VE ST A TE . 21 Set the A ...

  • Agilent Technologies 87020 - page 111

    4-55 Performance T ests 14. T e st Port R eceiv er Phas e Dynami c Accur acy In Cas e of Difficulty 1 If t he an alyz er fa ils the te st at all power l evels, b e sure you foll owed the recomme nded atte nuator settin gs as liste d in the “ Perf ormanc e Test Record . ” Repe at this per formance te st. 2 If both test port mea sured v alue s ar ...

  • Agilent Technologies 87020 - page 112

    4-56 Performanc e Tests 14. Tes t Port Re ceiv er Phas e Dyna mic Ac curacy Figure 4-33. Dynamic Accurac y (Phase) Procedure T est Port 2 Phase D ynamic Accuracy 1 Refer to the “ Test Port Receiver Magnitude Dynamic Accuracy ” portio n of the “ Perform ance Test Re cord, ” for the values in the “ Calc ulated Va lue ” co lu mn. 2 Copy th ...

  • Agilent Technologies 87020 - page 113

    4-57 Performance T ests 15. T est P ort Receiv er Ma gnitude Compress ion 7 For eve ry test port input pow er l evel, calculate the receiver phase dyna mic accuracy using the fol lowing formula : Phase Dynamic Ac curacy = SIN – 1 (B) 8 Writ e the valu e in the “ Result s Value ” colu mn of the “ Perf o rmance Test Record. ” T est Port 1 P ...

  • Agilent Technologies 87020 - page 114

    4-58 Performanc e Tests 15. Test Port Re ceiv er Magnit ude Comp ress ion 2 Press PRESET , MEA S , T rans: E/E S21 F WD . 3 Press AV G , IF BW , 10 , x1 . 4 Press MENU , CW FREQ , 50 , M/ µ . 5 Press SWEEP TYPE MENU , POWER SWEEP , ST ART , – 10 , x1 . 6 Press MENU , TRI GGER MENU , SINGLE . 7 At th e end of the sw eep, press SC ALE REF , AUTO S ...

  • Agilent Technologies 87020 - page 115

    4-59 Performance T ests 16. T est Port Re ceiver Phas e Compre ssion SEARC H: M IN . 25 Write the a bsolu te value o f th e marker 2 reading in the “ Mea sured Valu e ” column of th e “ Pe rformance Test Record. ” 26 Repeat St ep 19 thro ugh Step 25 for the o ther CW freq uencies listed f or P ort 1 in t he “ Perf orman ce Test Record. ? ...

  • Agilent Technologies 87020 - page 116

    4-60 Performanc e Tests 16. Tes t Port Re ceiv er Phas e Compre ssion For 75 Ω Analyzers Cable, 75 Ω , Type -N, 24-inch . . . . . . . . . . . . . . . . . . . . . Agile nt P/N 8120- 2408 Procedure T est Port 2 Phase C ompression 1 Connec t t he equ ipm ent as show n in Figure 4-35 . Figure 4-35. Test Port Phase Compression Te st Setup 2 Press PR ...

  • Agilent Technologies 87020 - page 117

    4-61 Performance T ests 16. T est Port Re ceiver Phas e Compre ssion T est Port 1 Phase Compress ion 13 Press MEAS , T rans: E/E S12 REV , FORM A T , PHASE . 14 Press MENU , CW FREQ , 50 , M/ µ . 15 Press MENU , TRI GGER MENU , SINGLE . 16 At th e end of the sw eep, p ress SCALE R EF , AUTO SC ALE . 17 Press MARKER , ∆ MODE MENU , ∆ REF= 1 , M ...

  • Agilent Technologies 87020 - page 118

    4-62 Performanc e Tests 17. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with out Option 00 6 Only) 17. Test Port Output/Input Harmonics (Option 002 Analyzers without Option 006 O nly) Perform th is test to dete rmine th e spectral purity of the Agilen t 8702D input and output tes t ports. Requi red Equipment For 50 Ω Analyzers Cabl ...

  • Agilent Technologies 87020 - page 119

    4-63 Performance T ests 17. T est Port Outpu t/Input Harmonics ( Option 0 02 Analyzer s witho ut Optio n 006 Only) Figure 4-36. Test Port Outpu t Harmonics T est Setup 5 Press MEAS , T rans: E/E S12 REV , INPUT PORTS , A . 6 After one swee p, pr ess DISP LA Y , DA T A → MEMORY , DA T A/MEM to normal ize the trace. 7 Press SYSTEM , HARMON IC M EAS ...

  • Agilent Technologies 87020 - page 120

    4-64 Performanc e Tests 17. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with out Option 00 6 Only) 15 Press SYSTEM , HARMON IC M EAS , HA RMONIC TH IRD . 16 After one sweep, pres s SC ALE R EF , AUTO SCAL E . 17 Press MARKER FCTN , MARKER MODE MENU , MKR SE ARCH , SEARCH MAX . 18 Write the marker 1 value o n the “ Performa nce Test ...

  • Agilent Technologies 87020 - page 121

    4-65 Performance T ests 17. T est Port Outpu t/Input Harmonics ( Option 0 02 Analyzer s witho ut Optio n 006 Only) chann el A ) 2n d har monic . Port 1 Input W orst Case 3rd Harmonic 29 Press STOP , 1 , G/n to change the stop frequ ency for measuring the receiver 3rd harmoni c. 30 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF . 31 After one swee p ...

  • Agilent Technologies 87020 - page 122

    4-66 Performanc e Tests 18. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with Option 006 Only ) 47 After one sweep, pres s DIS PLA Y , DA T A → MEMORY , DA T A/ MEM to no rmalize the trace. 48 Press SC ALE R EF , AUTO SC ALE , SCALE/DIV , 1 , x1 t o get a be tter viewin g of the trace . 49 Press SYSTEM , HARMON IC M EAS , HA RMONIC ...

  • Agilent Technologies 87020 - page 123

    4-67 Performance T ests 18. T e st Port Output/In put Harmonics (Option 002 Ana lyzers with Option 006 Only) Figure 4-38. Test Port Outpu t Harmonics T est Setup 5 Press MEAS , T rans: E/E S12 REV , INPUT PO RTS , A . 6 After one swee p, pr ess DISP LA Y , DA T A → MEMORY , DA T A/MEM to normal ize the trace. 7 Press SYSTEM , HARMON IC M EAS , HA ...

  • Agilent Technologies 87020 - page 124

    4-68 Performanc e Tests 18. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with Option 006 Only ) 14 Press SC ALE R EF , AUTO SC ALE , SCALE/DIV , 1 , x1 t o get a be tter viewin g of the trace . 15 Press SYSTEM , HARMON IC M EAS , HA RMONIC TH IRD . 16 After one sweep, pres s SC ALE R EF , AUTO SCAL E . 17 Press MARKER FCTN , MARKER MO ...

  • Agilent Technologies 87020 - page 125

    4-69 Performance T ests 18. T e st Port Output/In put Harmonics (Option 002 Ana lyzers with Option 006 Only) 27 Press MARKER FCTN , MARKER MODE MENU , MKR SE ARCH , SEARCH: MAX . 28 Write the mar ker 1 value (which app ears on the an alyzer dis play) on the “ Perform ance Test Re cord. ” This i s the worst ca se por t 1 input (recei ver chann e ...

  • Agilent Technologies 87020 - page 126

    4-70 Performanc e Tests 18. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with Option 006 Only ) harmoni c. 46 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF . 47 After one sweep, pres s DIS PLA Y , DA T A → MEMORY , DA T A/ MEM to no rmalize the trace. 48 Press SC ALE R EF , AUTO SC ALE , SCALE/DIV , 1 , x1 t o get a be tter viewin ...

  • Agilent Technologies 87020 - page 127

    4-71 Performance T ests Perfor manc e T est Reco rds Performance Test Records The follow ing tables are to re cord t he pe rform ance test recor ds fo r each of the tests. T est 1. T est Port Output Freq uency Range and Accura cy Test F requen cies (MHz) Min. (MHz) Resu lts M easur ed (MHz) Max. (MHz) Measur ement Uncer tainty (MHz ) 0.03 0.029 999 ...

  • Agilent Technologies 87020 - page 128

    4-72 Performanc e Tests Perf ormance Test Rec ords T est 2. Exter nal Source Mode Freq uency Range Test F requen cie s (GHz ) Results 0.010 _______ _______ ______ 0.020 _______ _______ ______ 0.100 _______ _______ ______ 1.000 _______ _______ ______ 2.000 _______ _______ ______ 3.000 _______ _______ ______ Option 006 4.000 _______ _______ ______ 5. ...

  • Agilent Technologies 87020 - page 129

    4-73 Performance T ests Perfor manc e T est Reco rds T est 3. T est Port Output Po wer Accuracy Test F requen cy Test Po rt Output Power (d Bm) Specif ication (dB) Measur ed Val ue (dB) Measur ement Uncer tainty (dB) 300 kHz 0 ± 1 ________ _______ _____ ± 0. 15 20 MH z 0 ± 1 _____ __________ _____ ± 0.10 50 MH z 0 ± 1 _____ __________ _____ ± ...

  • Agilent Technologies 87020 - page 130

    4-74 Performanc e Tests Perf ormance Test Rec ords T est 4. T est Port Output Po wer Range and Linear i ty (1 of 2) Test Settin gs Resu lts Meas ure d (dB) Power Leve l Linear ity (dB) Specific ation (dB) Measu rement Uncer tainty (dB) CW Frequency = 300 kHz – 15 ______________ ____ ___ _______ ________ ± 0.2 ± 0.15 – 13 ______________ ____ _ ...

  • Agilent Technologies 87020 - page 131

    4-75 Performance T ests Perfor manc e T est Reco rds – 1 __________ _______ _ ______ ___________ _ ± 0.2 ± 0.15 + 1 __________ _______ _ ______ ___________ _ ± 0.2 ± 0.15 + 3 __________ _______ _ ______ ___________ _ ± 0.2 ± 0.15 + 5 __________ _______ _ ______ ___________ _ ± 0.5 ± 0.15 + 7 __________ _______ _ ______ ___________ _ ± 0. ...

  • Agilent Technologies 87020 - page 132

    4-76 Performanc e Tests Perf ormance Test Rec ords T est 5. Minimum R Channel Level CW Freq uency Specific ation (dB) Test Po rt Power M easure ment Unc erta inty (dB) 300 kHz < – 35 _______ _______ ______ ± 1.0 3.29 MHz < – 35 __________ _______ ___ ± 1.0 3.31 MHz < – 35 __________ _______ ___ ± 1.0 15.90 MH z < – 35 _______ ...

  • Agilent Technologies 87020 - page 133

    4-77 Performance T ests Perfor manc e T est Reco rds T est 6. T est Port Input Noise Floor Level Freque ncy Rang e Test Po rt IF Bandwi dth Specifi cation (dBm) Calcu lated Value Measur ement Uncer tainty 50 kHz – 3 GHz Po rt 1 3 kHz – 82 _______ _____ N/A 50 kHz – 3 G Hz Por t 1 10 Hz – 102 _______ _____ N/A 50 kHz – 3 G Hz Por t 2 10 Hz ...

  • Agilent Technologies 87020 - page 134

    4-78 Performanc e Tests Perf ormance Test Rec ords T est 8. T est Port Crosstalk Test Settin gs Specif ication (dB) Measu red Value (dB) Measur ement Uncer tainty Crosstalk to Test Port 2 300 kHz – 3 GHz < – 100 _______ _______ ______ N/A Crosstalk to Test Port 2 300 kHz – 3 GHz < – 100 _______ _______ ______ N/A Option 006 Crosstalk ...

  • Agilent Technologies 87020 - page 135

    4-79 Performance T ests Perfor manc e T est Reco rds T est 9. Calibra tion Coefficients (1 of 2) Test De scriptio n Freque ncy Rang e Specifica tion (dB) Me asured Valu e (dB) Measur ement Uncer tainty (dB) Forward Directi on Directiv ity 300 kHz – 1. 3 GHz ≥ 35 __________ _______ ___ ± 0.9 Directiv ity 1.3 GHz – 3 GHz ≥ 30 ___ _______ ___ ...

  • Agilent Technologies 87020 - page 136

    4-80 Performanc e Tests Perf ormance Test Rec ords Trans. Trac king 300 kHz – 1.3 G Hz ± 1.5 __________ _______ ___ ± 0.006 Trans. Trac king 1.3 GHz – 3 GHz ± 1.5 ___ ___________ ______ ± 0. 009 Trans. Trac king Option 006) 3 GHz – 6 GHz ± 2.5 __________ _______ ___ ± 0.021 Forward Directi on Load Match 300 kHz – 1.3 GHz ≥ 18 ___ __ ...

  • Agilent Technologies 87020 - page 137

    4-81 Performance T ests Perfor manc e T est Reco rds T est 10. Sy stem T race Noise (Only for Analyzers without Option 006) CW Freq uency (GHz) Ratio Measured V alue Specif ication Measurement Uncer tainty 3A / R ________ _______ _____ < 0.006 dB rms N/A 3A / R ________ _______ _____ < 0.038 ° rms N/A 3B / R ________ _______ _____ < 0.006 ...

  • Agilent Technologies 87020 - page 138

    4-82 Performanc e Tests Perf ormance Test Rec ords T est 12. T est Port In put Impeda nce Test De scriptio n Test P ort Return Lo s s (dB) Specificati on (dB) Measu rement Uncertain ty (dB) 300 kHz – 1.3 GHz Port 2 __________ _______ ___ ≥ 18 ± 1.5 1.3 GHz – 3 GHz Port 2 ___ _______ __________ ≥ 16 ± 1.5 3 GHz – 6 GHz (Optio n 006) Port ...

  • Agilent Technologies 87020 - page 139

    4-83 Performance T ests Perfor manc e T est Reco rds T est 13. T est Port Receiv er Mag nitude Dynamic Accuracy Test P ort Input Power 8496A Setting (dB) Test P ort (dB) 8902A (dB) Calcul ated Value (dB ) Spec. (dB) Mea. Uncer. (dB ) Test Po rt 2 – 10 0 _________ ___ ______ ___ ______ ≤ 0.059 ± 0.01 – 20 10 _________ ___ ______ ______ ___ ? ...

  • Agilent Technologies 87020 - page 140

    4-84 Performanc e Tests Perf ormance Test Rec ords T est 14. T est Po rt Rec eiver Phase D ynamic Accura cy Test P ort Input Power Calcul ated Value (dB ) A B Resu lts Valu e (degr ees) Spec. (degr ees) Mea. Uncer. Test Port 2 – 10 _________ _________ ___ ______ ______ ___ ≤ 0.42 N/A – 20 _________ _________ ___ ______ ______ ___ ≤ 0.35 N/A ...

  • Agilent Technologies 87020 - page 141

    4-85 Performance T ests Perfor manc e T est Reco rds T est 15. T est Port Receiver Magnitude Compression CW Freq uency Test Port Measu red V a lue (dB) Specific ation (d B) M easure ment Unce rtai nty 50 MHz P ort 2 ___ _______ __________ ≤ 0. 45 N/A 1 GHz Port 2 ______ _______ _______ ≤ 0.45 N/A 2 GHz Port 2 ______ _______ _______ ≤ 0.45 N/A ...

  • Agilent Technologies 87020 - page 142

    4-86 Performanc e Tests Perf ormance Test Rec ords T est 16. T est Port Receiver Phase Co m pression CW Freq uency Test Port Measu red V alue (degr ees) Specific ation (deg rees) Measu rement Uncertain ty 50 MHz P ort 2 ___ _______ __________ ≤ 6 ° N/A 1 GHz Port 2 ______ _______ _______ ≤ 6 ° N/A 2 GHz Port 2 ______ _______ _______ ≤ 6 ° ...

  • Agilent Technologies 87020 - page 143

    4-87 Performance T ests Perfor manc e T est Reco rds T est 17. T est Port Output/Input Harmonics (Option 002 Analyzers without Option 006 Only) Test De scriptio n Speci fication (dBc) Measur ement Va lue (dBc) Measu rement Uncertain ty (dB) Test Port Out put Harmoni cs 2nd ≤ 25 ______ ______ ________ ± 1. 0 3rd ≤ 25 ______ ______ _______ _ ± ...

  • Agilent Technologies 87020 - page 144

    4-88 Performanc e Tests Perf ormance Test Rec ords T est 18. T est Port Output/Input Harmonics (Option 002 Analyzers with Option 006 Only) Test De scriptio n Speci fication (d Bc) Measur ement Va lue (dBc) Measu rement Uncertain ty (dB) Test Port Out put Harmoni cs 2nd ≤ 25 ______ ______ ________ ± 3. 0 3rd ≤ 25 ______ ______ _______ _ ± 3.0 ...

  • Agilent Technologies 87020 - page 145

    5 Agilent 8702D O ption 01 1 and Agilent 85046A/ 47A Syste m Ver ification 5-4 Step 1. I nitial iza tion 5-4 Step 2 . Measu rement Calibra tion 5-6 Step 3. Device Ve rification 5-8 In Case of Difficul ty 5-11 Agilent 870 2D Option 01 1 and Agile nt 85044A Syst em Verifi cation 5-13 Step 1. I nitial iza tion 5-1 3 Step 2 . Measu rement Calibra tion ...

  • Agilent Technologies 87020 - page 146

    5-2 Automated V erification – Option 011 Automate d Performan ce Verifica tion for Option 011 Automated Performance Verification for Option 011 The auto mated per formance verification pr ocedures in this chapte r provid e a high level of c onfiden ce that t he Agilent 8702D Optio n 01 1 is wo rking prop - erly . Performan ce ver ification p r oc ...

  • Agilent Technologies 87020 - page 147

    5-3 Automated V e rification – Option 011 Automate d Performanc e V erification for Option 0 11 How to select the s y stem veri fication procedure Check to see how th e verif ication kit fl oppy disk is la bele d: • If th e disk is la beled V e rification Data Di sk , pro ceed with the Agilen t 8702D Option 011 Autom ated M ode S ystem V erific ...

  • Agilent Technologies 87020 - page 148

    5-4 Automated V erification – Option 011 Agilent 8702D Option 011 a nd Agilent 85046A/47A System Verification Agilent 8702D Option 01 1 and Agilent 85046A/ 47A Syst em Ve rific ation In o rder to run th is pro cedur e, t he fo llowing e quipment is r equi red: S-Parame ter test s et (for anal yzers without O ptio n 006) . . . . Agilent 85046A S-P ...

  • Agilent Technologies 87020 - page 149

    5-5 Automated V e rification – Option 011 Step 1. Initializatio n Figure 5-1. System Verification Test Setup 2 While the eq uipment is w a rmi ng up, r eview the conn ector care infor mation in the Agilent 870 2D User ’ s Gui de . 3 Insert the verificat ion kit disk into the anal yzer ’ s disk dr ive. 4 Press PRESET , SAVE/RECAL L , SELECT DI ...

  • Agilent Technologies 87020 - page 150

    5-6 Automated V erification – Option 011 Step 2. Me asurement Calibration Step 2. Measurem ent Cali bration 1 Press CAL , CAL KIT & ST DS , SEL ECT CAL KIT , CAL KIT :7mm , RETURN , RETURN , CALIBRA TE MENU , FULL 2 -PORT . 2 Press ISOLA TION , O MIT ISOLA TION , ISOLA TION DONE . 3 Press REFL ECTION . 4 Con nec t the “ open ” end o f th ...

  • Agilent Technologies 87020 - page 151

    5-7 Automated V e rification – Option 011 Step 2. Meas urement Cali bration 7 Press F ORWARD:SHORT . 8 When the ana lyzer displays the message CONNECT STD THEN PRESS KEY TO MEASURE , conn ect t he 50 o hm terminat ion (su pplie d in t he calibrat ion kit) to r eference test port 1, as sh own in Figur e 5-2 . 9 Press F ORWARD:LOAD . 10 When the an ...

  • Agilent Technologies 87020 - page 152

    5-8 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 18 Press TR ANSM ISSION , F WD TRANS THRU . 19 When the analy zer fi nish es t he me asure ment, pres s FWD MA TCH THRU . 20 When the analy zer fi nish es t he me asure ment, pres s REV TRANS TH RU . 21 When the analy zer fi nish es t he me asure ment, pres s REV MA TCH THRU ...

  • Agilent Technologies 87020 - page 153

    5-9 Automated V e rification – Option 011 Step 3. De vice V erification 3 Press CONTINUE to run the test : • If you switche d the recor d function off , you have to pres s CONTI NUE after each S -paramete r meas ureme nt. • If you switche d the record function on , the test disp lays an d prin ts the pass/ fail informatio n for the S -para me ...

  • Agilent Technologies 87020 - page 154

    5-10 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 6 When all measurements are complete, replace the attenuator with the verification mismat ch, as shown in Figure 5-6 . Figure 5-6. Mismatch Devic e Verificati on Setup 7 Press RETURN , TESTS , 30 , x1 , EXECUTE TEST , CONTINUE . ...

  • Agilent Technologies 87020 - page 155

    5-11 Automated V e rification – Option 011 In Case of Difficulty 8 When the analyzer f inishe s all the measuremen ts, reconnect the mismat ch verification device, as shown i n Figure 5- 7 . Figure 5-7. Mism atch Device Verific ation Setup 9 Press RETURN , TESTS , 31 , x1 , EXECUTE TEST , CONTINUE . 10 You hav e comp leted th e system v erificati ...

  • Agilent Technologies 87020 - page 156

    5-12 Automated V erification – Option 011 In Case of Difficulty 3 If the analyzer sti ll fa ils the test, check the measureme nt calibra tion as follows: a Press PRESET . b Recal l the cali bration by pr essing SA VE/RECAL L , SEL ECT DI SK , INTERNAL MEMO- RY , RETURN . c Use th e front panel kno b to highl ight t he calib ratio n you want to re ...

  • Agilent Technologies 87020 - page 157

    5-13 Automated V e rification – Option 011 Agilent 87 02D Opt ion 011 and Ag ilent 8504 4A Sy stem V eri fication Agilent 8702D Option 01 1 and Agilent 85044A System Verification In o rder to run th is pro cedur e, the fo llowing e quipment is require d: Transmi ssion/r efle ction test set . . . . . . . . . . . . . . . . . . . . . . . . A gilent ...

  • Agilent Technologies 87020 - page 158

    5-14 Automated V erification – Option 011 Step 2. Me asurement Calibration Figure 5-8. System Verification Test Setup 2 While the eq uipment is w a rmi ng up, r eview the conn ector care infor mation in the Agilent 870 2D User ’ s Gui de . 3 Insert the verificat ion kit disk into the anal yzer ’ s disk drive. 4 Press PRESET , SAVE/REC ALL , S ...

  • Agilent Technologies 87020 - page 159

    5-15 Automated V e rification – Option 011 Step 2. Meas urement Cali bration MENU , ONE-P A TH 2-PO RT . 2 Press ISOLA TION , O MIT ISOLA TION , ISOLA TION DONE . 3 Press REFL ECTION . 4 Con nec t the “ open ” end o f th e open/ s hort combi nation (supplied i n the calibrat ion kit) to reference test port 1, as shown in Figure 5-9 . Figure 5 ...

  • Agilent Technologies 87020 - page 160

    5-16 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 10 When t he analyze r finishes meas uring the stan dard, press ST ANDA RDS DONE . 11 Con nect th e test port c ables as sho wn Figure 5-10 . Figure 5-10. Transmission Cali bration Setup 12 Press TR ANSM ISSION , F WD TRANS THRU . 13 When the analy zer fi nish es t he me asu ...

  • Agilent Technologies 87020 - page 161

    5-17 Automated V e rification – Option 011 Step 3. De vice V erification as s hown in F igure 5- 11 . Figure 5-11. Connections fo r the 20 dB Att enuator 3 Press CONTINUE to run the test : • If you switche d the recor d function off , you have to pres s CONTI NUE after each S -paramete r meas ureme nt. • If you switche d the record function o ...

  • Agilent Technologies 87020 - page 162

    5-18 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 4 When th e analyzer fi nishes all t he measurements, connect the 5 0 dB atten u ator (supplie d in t he veri fication kit), as shown in Figure 5-12 . Figure 5-12. Connections fo r the 50 dB Att enuator 5 Press RETURN , TESTS , 29 , x1 , EXECUTE TEST , CONTIN UE . ...

  • Agilent Technologies 87020 - page 163

    5-19 Automated V e rification – Option 011 Step 3. De vice V erification 6 When all measurements are complete, replace the attenuator with the verification mismat ch, as shown in Figur e 5-13 . Figure 5-13. Mismatch Device Verification Setup 7 Press RETURN , TESTS , 30, x1 , EXECUTE TEST , CONTINU E . ...

  • Agilent Technologies 87020 - page 164

    5-20 Automated V erification – Option 011 In Case of Difficulty 8 When th e analyzer finishes al l the me asurements, r econnect the mis match verification device, as shown i n Figure 5- 14 . Figure 5-14. Mism atch Device Verific ation Setup 9 Press RETURN , TESTS , 31 , x1 , EXECUTE TEST , CONTINUE . 10 You hav e comp leted th e system v erifica ...

  • Agilent Technologies 87020 - page 165

    5-21 Automated V e rification – Option 011 In Case of Difficulty c Press RECALL ST A TE . d Repeat “ Step 3. De vice Veri fication ” on page 5-16 . 3 If the analyze r still fails the test, ch eck the measuremen t calibration as fo llows: a Press PRESET . b Recall t he calibratio n by press ing SA VE/RECALL , SELECT DI SK , INTERNAL DISK , RE- ...

  • Agilent Technologies 87020 - page 166

    ...

  • Agilent Technologies 87020 - page 167

    6 1. Source Frequency Range and A ccuracy 6-3 2. Source Power Range, Linearity, and Accuracy 6-5 3. Receiver Minimum R Channel Level 6-9 4. Receiver Mi nimum R Chann el Level for E xternal Source Mode 6-12 5. Recei ver Channe l Noise Floor Level (Only for Analy zers withou t Opt ion 006) 6-14 6. Recei ver Channe l Noise Floor Level (Only for Analy ...

  • Agilent Technologies 87020 - page 168

    6-2 Performanc e Tests – Opt ion 0 11 Manua l Perform ance Tests - O ption 011 Manual Performance Tests - Option 011 This chapter c ontain s procedur es which te st the elec tric al performa nce of the Agilent 870 2D Option 01 1. If you are no t using an A gilen t 8702D Option 0 11, refer to Chapt er 4, “ Performance T ests ” . Bef ore starti ...

  • Agilent Technologies 87020 - page 169

    6-3 Performance T ests – Option 011 1. Sour ce Fre quenc y Range an d Accu racy WAR NI N G Any servi cing, adjustme nt, maintena nce, or re p air of this p r oduct must be per forme d only by qualified p ersonn el. Repai r infor mation provided in the In Cas e of Difficulty sectio ns o f this chap ter are provided for quali fied servi ce perso nn ...

  • Agilent Technologies 87020 - page 170

    6-4 Performanc e Tests – Opt ion 0 11 1. Sour ce Fre que ncy Rang e and Accurac y Figure 6-1. Source Fre quency Rang e and Accuracy Test Setup 2 Press PRESET , MEN U , CW F REQ . 3 Press 300 , k/m and write the frequency counter reading on the "Performan ce Test R ecor d." 4 Repeat Step 3 for each inst rument fr equency li sted in t he ...

  • Agilent Technologies 87020 - page 171

    6-5 Performance T ests – Option 011 2. Sour ce Powe r Range , Linear ity, and Accu racy 2. Source Power Range, Linear ity, and Ac curacy Perfo rm this test to ver ify the analyze r ’ s powe r rang e and line arity at d ifferen t CW freq uencies t hroug hout the analyz er ope rating freque ncy rang e. Requi red Equipment Power Mete r . . . . . . ...

  • Agilent Technologies 87020 - page 172

    6-6 Performanc e Tests – Opt ion 0 11 2. Sou rce P ower Rang e, L inear ity, and Accur acy 2 Zero and cal ibrate th e power m eter. Also , set th e power meter fo r dBm. Refer to the power me ter operat ing and servi ce manual for m ore inform ation on how to do this ta sk. 3 Press PRESET , MEN U , POWER , 10 , x1 . 4 Press MENU , CW FREQ , 300 , ...

  • Agilent Technologies 87020 - page 173

    6-7 Performance T ests – Option 011 2. Sour ce Powe r Range , Linear ity, and Accu racy 9 Write the power meter re ading in th e "Second Value" colu mn on the "Performance Test Record." 10 Calculat e the path loss throug h the power sp litter with this formula: First V alue – Second V al ue = Path Loss 11 Write the r esult o ...

  • Agilent Technologies 87020 - page 174

    6-8 Performanc e Tests – Opt ion 0 11 2. Sou rce P ower Rang e, L inear ity, and Accur acy front pan el. 16 Press PO WER , – 5 , x1 . W rite t he po wer met er rea ding in th e “ Me asur ed Value ” column on th e “ Pe rformance Test Record ” . 17 On t he “ Perf orman ce Test Record ” , copy the “ Path Loss ” val ue, pr eviously ...

  • Agilent Technologies 87020 - page 175

    6-9 Performance T ests – Option 011 3. Rece iver Minimum R Channel Le vel 31 Press MENU , CW FREQ , 300 , k/m . Se t the power c alibra tion fact or for t his CW frequency . 32 On t he “ Perfor mance Test Record ” , c opy the “ Path Loss ” v alue , previousl y calcu late d for th is CW f requency, into the “ Pass Loss ” c olumn. 33 Ca ...

  • Agilent Technologies 87020 - page 176

    6-10 Performanc e Tests – Opt ion 0 11 3. Rece iver Minimum R Channel Le vel Requi red Equipment Adapter, APC-3.5 (m) to APC-7 . . . . . . . . . . . . . . . . . . Agi lent P/N 1250- 1746 Cable, APC-7 24- inch . . . . . . . . . . . . . . . . . . . . . . . . . . . Ag ilent P/N 8120-477 9 Atten uator , 20 dB . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 177

    6-11 Performance T ests – Option 011 3. Rece iver Minimum R Channel Le vel c If the a nalyzer still doesn ’ t phase lock, contin ue increasing the sou rce output power un til phas e lock is ac hieved. d Write the mar ker value in th e “ Perfo rmanc e Test Reco rd ” . • Repeat Step 4 throu gh Step 6 fo r the other CW fre quenc ies lis ted ...

  • Agilent Technologies 87020 - page 178

    6-12 Performanc e Tests – Opt ion 0 11 4. Re ceiver Mini mum R Channel Le vel for Ex ternal Sour ce Mod e 5 Refe r to the Agilent 8753 D Option 0 11 Service G uide for m ore troublesh ooting informat ion. 4. Re ceiver Mi nimu m R Channe l Level for Exte rnal Source Mode Perfo r m t his te st to ve rify prop er ph ase lock i n the external source ...

  • Agilent Technologies 87020 - page 179

    6-13 Performance T ests – Option 011 4. Rece iver Minimu m R Channe l Level f or Exte rnal Source Mode 2 On the ext erna l source, press PRESET , POWER LEVEL , 4 , dB(m) , CW , 10 , MHz . 3 On the an alyzer, press PRESET , MENU , CW FREQ , 10 , M/ µ , SY STEM , INSTRUMENT MODE , EXT SOURCE AUTO to set up the an alyzer f or an ex ternal s ource i ...

  • Agilent Technologies 87020 - page 180

    6-14 Performanc e Tests – Opt ion 0 11 5. Receive r Chann el Noise Floor Level ( Only for A nalyzer s withou t Option 006) In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The ope ...

  • Agilent Technologies 87020 - page 181

    6-15 Performance T ests – Option 011 5. Re ceiver Channel Noise Floor Level ( Only for Analy zers without Option 006) Figure 6-7. Receiver Ch annel Noise Floor Level Test Se tup 2 Press PRESET , MEN U , POWER , – 10 , x1 . Receiver Ch annel A Noise Floor Level wi th a 3 kHz IF BW 3 Press MEAS , INPUT PO RTS , A , FORMA T , LIN MAG , SCALE R EF ...

  • Agilent Technologies 87020 - page 182

    6-16 Performanc e Tests – Opt ion 0 11 5. Receive r Chann el Noise Floor Level ( Only for A nalyzer s withou t Option 006) 11 Use th e fol lowing equa tion to c onvert the linear magnitude m ean value to lo g magn itude: Power (dBm) = 20 * [log 10 (linear magnitude mean value)] 12 Write this calcul ated value in the “ Perf orma nc e Test Re cor ...

  • Agilent Technologies 87020 - page 183

    6-17 Performance T ests – Option 011 6. Rece iver C hannel Noise Floo r Level (Only for A nalyzer s with Opt ion 006) 6. Receiver Channel Noi se Floor Le vel (Only for Analyzers with Option 006) Perfor m this test to determ ine t he an alyze r receiv er chan nel no ise fl oor lev els. Requi red Equipment Attenua tor, 20 dB . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 184

    6-18 Performanc e Tests – Opt ion 0 11 6. Rece iver Channel Nois e Floor Level (Only for Analyz ers with Option 00 6 ) 5 When the analyze r finishes the sweep , not ice the mean value, wh ich appea rs on the an alyzer displ ay. 6 Use th e fol lowing equa tion to c onvert the linear magnitude m ean value to lo g amplit ude: Power (dBm) = 20 * [log ...

  • Agilent Technologies 87020 - page 185

    6-19 Performance T ests – Option 011 6. Rece iver C hannel Noise Floo r Level (Only for A nalyzer s with Opt ion 006) Receiver Ch annel B Noise Floor Leve l with a 3 kHz IF BW (50 kHz – 3 GHz ) 18 Press AV G , IF BW , 3 , k/m t o cha nge th e IF bandw idth to 3 k Hz. 19 Press MENU , TRI GGER MENU , SINGLE . 20 When th e analyzer finishes t he s ...

  • Agilent Technologies 87020 - page 186

    6-20 Performanc e Tests – Opt ion 0 11 6. Rece iver Channel Nois e Floor Level (Only for Analyz ers with Option 00 6 ) Receiver Ch annel A Noise Floor Leve l with 10 Hz IF BW (3 GH z – 6 GHz) 33 Press MEAS , INPUT PO RTS , A . 34 Press MENU , TRI GGER MENU , SINGLE . 35 When th e analyzer finishes t he sweep, record the mean value, which appear ...

  • Agilent Technologies 87020 - page 187

    6-21 Performance T ests – Option 011 7. Rece iver Magnitude Frequ ency Res pons e 7. Receiver Magnit ude Frequency Response Perfo rm this te st to ve rify how well the analy zer t ransfers i nformati on from the RF to IF , an d how accur ately it processes and displ ays that informati on. Requi red Equipment Power Mete r . . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 188

    6-22 Performanc e Tests – Opt ion 0 11 7. Rece iver Magnitude Frequ ency Res pons e 3 Press PRESET , MA RKER , MEAS , INPUT PORTS , R , MENU , PO WER , 6 , x1 . 4 Press CW FREQ , 300 , k/m . S et the calibration factor on the po wer meter for t his CW frequency . 5 Write the power met er readin g on the “ Perform ance Test Record. ” 6 Write t ...

  • Agilent Technologies 87020 - page 189

    6-23 Performance T ests – Option 011 7. Rece iver Magnitude Frequ ency Res pons e Input B Magnitude Freque ncy Response 13 Connec t t he equ ipm ent as show n in Figure 6-11 . Figure 6-11. Magnitude Freque ncy Response Te st Setup (Recei ver Inpu t B) 14 Press MEAS , INPUT PO RTS , B , MENU to start mea surin g the pow er del ivered to rece iver ...

  • Agilent Technologies 87020 - page 190

    6-24 Performanc e Tests – Opt ion 0 11 8. Rece iver Phase Fr equency Res ponse In Cas e of Difficulty 1 Suspect poo r trackin g betwee n the ports of th e power s plitter if al l receiver inpu ts fail. Try to repe at the te st with anot her power sp litter. 2 Suspect source drift if rece iver i nputs A and B fail th is tes t at any freque ncy. Co ...

  • Agilent Technologies 87020 - page 191

    6-25 Performance T ests – Option 011 8. Rece iver P hase Freq uenc y Response Figure 6-12. Phase Frequ ency Response Test Setup Phase Frequency Response from 300 kHz to 3 G Hz 2 Press PRESET , MEN U , POWER , 10 , x1 . 3 Only for Analyz ers with Opti on 006: Press STO P , 3 , G/n . 4 Press FORMA T , PHA SE , MARKER FCTN , MARKER M ODE MENU , ST A ...

  • Agilent Technologies 87020 - page 192

    6-26 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk 12 Press SCALE REF , ELECTRICAL DELA Y . Turn t h e analyze r front panel knob to vary the e lectrical d elay until t he tr ace is in t he mos t lin ear horizont al positio n . 13 Press MENU , TRI GGER MENU , SINGLE . Write the p-p value , which appear s on the analy zer display ...

  • Agilent Technologies 87020 - page 193

    6-27 Performance T ests – Option 011 9. Rece iver In put Cross talk Requi red Equipment 2-way Power Sp litter (2), 50 Ω . . . . . . . . . . . . . . . .Agilent 11667A Option 001 Termi nation ( 3), 5 0 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A gil ent 908A Attenua tor, 20 dB . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 194

    6-28 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk (Only for Op tion 006 Analyzers) R i nto A Crosstal k from 3 GHz to 4.5 GHz 9 Press ST ART , 3 , G/n , STOP , 4.5 , G/n , NUMBER of GROUPS , 5 , x1 . 10 When the analyze r finis h es the nu mber of sweeps, write the ma rker value, which appea rs on t he analyzer display, o n the ...

  • Agilent Technologies 87020 - page 195

    6-29 Performance T ests – Option 011 9. Rece iver In put Cross talk B into A Crosstalk from 300 kHz to 1 GHz 22 Connec t t he equ ipm ent as show n in Figure 6-14 . Figure 6-14. B into A Rec eiver Input Cro sstalk Test Setup 23 Press ST ART , 300 , k/m , STO P , 1 , G/n. 24 Press MEAS , INPUT PO RTS , A/B , MENU , TRIGGER MENU , NUMBER of GROUPS ...

  • Agilent Technologies 87020 - page 196

    6-30 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk (Only for Op tion 006 Analyzers) B i nto A Crosstal k from 4.5 GHz to 6 GHz 30 Press ST ART , 4.5 , G/n , STOP , 6 , G/n , TRIGGER MEN U , NUMBER of GROUPS , 5 , x1 . 31 When the analyze r finis h es the nu mber of sweeps, write the ma rker value, which appea rs on t he analyzer ...

  • Agilent Technologies 87020 - page 197

    6-31 Performance T ests – Option 011 9. Rece iver In put Cross talk A into B Cro sstalk from 1 GHz to 3 GHz 38 Press ST ART , 1 , G/ n , STOP , 3 , G/n . 39 Press MEAS , INPUT PORTS , A/R , AV G , AVERAGING OF F , MENU , TRIG G ER MENU , SINGLE . 40 At the en d of the sw eep, pr ess DIS PLA Y , DA T A → MEMORY , DA T A/MEM , MEAS , INPU T PORTS ...

  • Agilent Technologies 87020 - page 198

    6-32 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emoval of part s is likely to exp ...

  • Agilent Technologies 87020 - page 199

    6-33 Performance T ests – Option 011 10. Re ceiver T race N oise 10. Recei ver Trace Noise Perfo r m t his te st to ve rify the r eceiver t race n oise on a CW signal i n ratio mode. Requi red Equipment 3-way Power Splitter , 50 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agil ent 1185 0C Attenua tor, 10 dB . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 200

    6-34 Performanc e Tests – Opt ion 0 11 10. Rece iver Trace Noi se statistic fea ture. 5 Write the s.dev (stand ard deviation) valu e, which appears on the analyzer disp lay, o n the "Perfo rmance Test Reco rd." 6 Press ME AS , INPUT PORTS , B/R . Write the s.dev (standard de viation) value on the "Performance Test Record." 7 P ...

  • Agilent Technologies 87020 - page 201

    6-35 Performance T ests – Option 011 11. Recei ver I nput Impe dance 11. Recei ver Input Impedance Perfo r m t his te st to ve rify the r eturn los s of each of t he ana lyzer ’ s rece iver input s. Requi red Equipment Test s et, 50 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . A gilen t 85044A/8 5046A/85 047A 2-way Power Splitter , 5 ...

  • Agilent Technologies 87020 - page 202

    6-36 Performanc e Tests – Opt ion 0 11 11. Rece iver Inpu t Imped ance 2 Press PRESET , MEN U , NUMBER of POINTS , 1601 , x1 . 3 Press CAL , CAL KI T & STD S , SELECT CAL KI T , N 50 Ω , RETURN , R ETU RN , CALIBRA TE MENU , S11 1-PORT . 4 Connect an open to t he test port cable adap ter, by pressing FORWARD: OPENS , OPEN (M) , DONE: OPENS ...

  • Agilent Technologies 87020 - page 203

    6-37 Performance T ests – Option 011 11. Recei ver I nput Impe dance Figure 6-18. Receiver A In put Impedanc e Test Se t up 14 Press PRESET , MEA S , INPUT PORTS , B/R , MENU , NUMBER of POI NTS , 1601 , x1 . 15 Press CAL , CALI BRA TE ME NU , S11 1-PORT . Repeat Step 4 through Step 1 2 for the analy zer recei ver in put A retu rn loss. ...

  • Agilent Technologies 87020 - page 204

    6-38 Performanc e Tests – Opt ion 0 11 11. Rece iver Inpu t Imped ance 16 Connec t t he equ ipm ent as show n in Figure 6-19 . Figure 6-19. Receiver R Input I mpedance Te st Calibra tion Test Se tup 17 Press PRESET , MEA S , INPUT PORTS , A/B , MENU , NUMBER of POINTS , 1601 , x1 . 18 Press CAL , CALIBRA TE MENU , S11 1-PORT . Repe at Step 4 thro ...

  • Agilent Technologies 87020 - page 205

    6-39 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy 20 Repeat Step 7 throu gh Step 12 to measure t he receiver R inp u t imp edance . In Cas e of Difficulty WAR NI N G These servicing instructions a re for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you ar ...

  • Agilent Technologies 87020 - page 206

    6-40 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy Figure 6-21. Receiver Ma gnitude Dynamic Accur acy Requi red Equipment Measur ing Recei ver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agi len t 8902A Step Atte nuator, 110 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87020 - page 207

    6-41 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy c Press AV G , IF B W , 10 , x1 . 4 Connec t t he equ ipm ent as show n in Figure 6-22 . Figure 6-22. Channe l A Magnitud e Dynamic Acc uracy Test Se tup 5 On t he Agil ent 8702D Opt ion 0 11: a Press MEAS , INPUT PO RTS , A , MENU , POWER . b Using t he analyz er fr ...

  • Agilent Technologies 87020 - page 208

    6-42 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy 6 On the Agi lent 8902A , press the blue shift ke y and SET REF . 7 On t he Agil ent 8702D Opt ion 0 11: a Press CAL , CALI BRA TE ME NU , RESPONSE , THRU . b After the analyzer fi nishes the measur ement, pres s DONE: RESPO NSE . c Press SAVE/R ECALL , SA VE ST A ...

  • Agilent Technologies 87020 - page 209

    6-43 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy 18 Connec t t he equ ipm ent as show n in Figure 6-23 . Figure 6-23. Channe l B Magnitud e Dynamic Acc uracy Test Se tup 19 On t he Agil ent 8702D Opt ion 0 11: a Press MENU , PO WER . b Using t he analyz er fro nt panel knob, adjust th e test por t pow er fo r a rea ...

  • Agilent Technologies 87020 - page 210

    6-44 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy a Press CAL , CALI BRA TE ME NU , RESPONSE , THRU . b After the analyzer fi nishes the measur ement, pres s DONE: RESPO NSE . c Press SAVE/R ECALL , SA VE ST A TE . 22 Set the Agil ent 8496A to 0 dB. 23 On t he Agil ent 8 702D Opt ion 0 11, pre ss MENU , TRIGGER ME ...

  • Agilent Technologies 87020 - page 211

    6-45 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy Figure 6-24. Channel R M agnitude Dynamic Accurac y Test Setup 31 Set the Agil ent 8496A to 20 dB. 32 On t he Agil ent 8702D Opt ion 0 11: a Press C ONTINUOUS , MEAS , IN PUT PORTS , R , MENU , POW ER . b Using t he analyz er fro nt panel knob, adjust th e test por t ...

  • Agilent Technologies 87020 - page 212

    6-46 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy 36 On t he Agil ent 8 702D Opt ion 0 11, pre ss MENU , TRIGGER MENU , SINGL E . 37 Write the me an value i n the "Receiver Ch annel R" column of the "Performan ce Test R ecor d." 38 Write the Agile nt 8902A readou t in the "8902 A" col ...

  • Agilent Technologies 87020 - page 213

    6-47 Performance T ests – Option 011 13. Rece iver P hase D ynamic Ac curac y a Perfo rm the "IF Amplifi er Corr ection Const ants " and "ADC O ffset Correct ion Constants" proced ures (located in the "Adju stments and Corr ectio n Con- stants" chapter of the Agi lent 8753D Option 011 Service Gui de ). b Repe at this ...

  • Agilent Technologies 87020 - page 214

    6-48 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n 4 Write the result in the "A" column of t he "Perfor mance Test Record." 5 For ever y receiver in put pow er level, cal culate "B" us ing the follo wing fo rmula : B = 1 – A 6 Writ e the result in t he " B" co lumn of t he " ...

  • Agilent Technologies 87020 - page 215

    6-49 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n Addition al Required Equi pment for Analyzers with Op tion 006 Power Senso r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agilent 8 481A Procedure Chan nel A Magnitude Compression 1 Zero a nd ca librate th e power mete r. 2 Connec t t he ...

  • Agilent Technologies 87020 - page 216

    6-50 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n Figure 6-26. Channel A M agnitude Compression T est Setup ...

  • Agilent Technologies 87020 - page 217

    6-51 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n 3 Press PRESET , AV G , IF BW , 10 , x1 . 4 Press MENU , CW FR EQ , 50 , M/ µ . Set th e calibrat ion facto r on the po wer meter for this CW freque ncy. 5 Press PO WER , – 4 , x1 . Use the analyzer ’ s fr ont pan el k nob t o adjust the s ource powe r for a power met ...

  • Agilent Technologies 87020 - page 218

    6-52 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n 20 Press STOP and en ter the “ St op Power ” value as determin ed in Step 18 . 21 Press MENU , TRI GGER MENU , SINGLE . 22 At th e end of the sw eep, press SC ALE REF , AUTO SC ALE . 23 Press MARKER , ∆ MODE MENU , ∆ REF=1 , MA RKER FCTN , MARKER MODE MENU , MKR ...

  • Agilent Technologies 87020 - page 219

    6-53 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n Channel B Magni tude Compression 27 Connec t t he equ ipm ent as show n in Figure 6-27 . Figure 6-27. Channel B Magnitude Compression Test Setup ...

  • Agilent Technologies 87020 - page 220

    6-54 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n 28 Press MEAS , INPUT PO RTS , B/R . 29 Repeat Step 26 for the CW fr equencie s listed i n the “ Perfo rman ce Te st Record ” . Channel R Magnitud e Compression 30 Connec t t he equ ipm ent as show n in Figure 6-28 . ...

  • Agilent Technologies 87020 - page 221

    6-55 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n Figure 6-28. Channel R Magn itude Compression Test Setup 31 Repeat Step 26 for the CW fr equencie s listed i n the “ Perfo rman ce Te st Record ” . ...

  • Agilent Technologies 87020 - page 222

    6-56 Performanc e Tests – Opt ion 0 11 15. Rece iver Phase Co mpressi on In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emoval of part s is likely to ...

  • Agilent Technologies 87020 - page 223

    6-57 Performance T ests – Option 011 15. Rece iver Ph ase Co mpressi on Procedure Channel A Phase Compressi on 1 Zero a nd ca librate th e power mete r. 2 Connec t t he equ ipm ent as show n in Figure 6-29 . Figure 6-29. Channe l A Phase Compre ssion Test Setup ...

  • Agilent Technologies 87020 - page 224

    6-58 Performanc e Tests – Opt ion 0 11 15. Rece iver Phase Co mpressi on 3 Press PRESET , AV G , IF B W , 10 , x1 , FORM A T , PHAS E . 4 Press MENU , CW FREQ , 50 , M / µ . Set the calibrat ion factor on the powe r meter for this CW freque ncy. 5 Press PO WER , – 4 , x1 . 6 Use the analyzer ’ s front panel knob to adjus t the s ource po wer ...

  • Agilent Technologies 87020 - page 225

    6-59 Performance T ests – Option 011 15. Rece iver Ph ase Co mpressi on keypad to en ter the “ Sta rt Power ” value as determined in Step 18 . 21 Press STOP and en ter the “ St op Power ” value as determin ed in Step 19 . 22 Press MENU , TRI GGER MENU , SINGLE . 23 At th e end of the sw eep, p ress SCALE R EF , AUTO SC ALE . 24 Press MARK ...

  • Agilent Technologies 87020 - page 226

    6-60 Performanc e Tests – Opt ion 0 11 15. Rece iver Phase Co mpressi on Channel B Phase Compressi on 28 Connec t t he equ ipm ent as show n in Figure 6-30 . Figure 6-30. Channe l B Phase Compre ssion Test Setup 29 Press MEAS , INPUT PO RTS , B/R . 30 Repeat Step 27 for t he ot her CW fr eque ncies l iste d in t he “ Performance Test Record. ? ...

  • Agilent Technologies 87020 - page 227

    6-61 Performance T ests – Option 011 15. Rece iver Ph ase Co mpressi on Channel R Phase Compressi on 31 Connec t t he equ ipm ent as show n in Figure 6-31 . Figure 6-31. Channel R Phas e Compression T est Setup 32 Repeat Step 27 for t he ot her CW fr eque ncies l iste d in t he “ Performance Test Record. ” ...

  • Agilent Technologies 87020 - page 228

    6-62 Performanc e Tests – Opt ion 0 11 16. Sour ce and Receiv er Ha rmon ics (Op tion 00 2 Onl y) In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emova ...

  • Agilent Technologies 87020 - page 229

    6-63 Performance T ests – Option 011 16. Sour ce and Re cei ver Harmo nics (Option 0 02 Only) Figure 6-32. Source Harm onics Test Setup 2 Press PRESET , MEN U , POWER , 20 , x1 . 3 Press ST ART , 16 , M/ µ , STOP , 1.5 , G/n to set the freque ncy range f or search ing the source 2nd har monic. 4 Only for Analyz ers with Opti on 006: Press STO P ...

  • Agilent Technologies 87020 - page 230

    6-64 Performanc e Tests – Opt ion 0 11 16. Sour ce and Receiv er Ha rmon ics (Op tion 00 2 Onl y) 13 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF , DISPLA Y . 14 After one sweep, pres s DA T A → ME MO RY , DA T A/MEM to no rmalize the t race and record t he fundam ental. 15 Press SYSTEM , HARMON IC M EAS , HA RMONIC TH IRD to pre pare the ana ...

  • Agilent Technologies 87020 - page 231

    6-65 Performance T ests – Option 011 16. Sour ce and Re cei ver Harmo nics (Option 0 02 Only) 24 Move t he receive r A input cabl e to r eceiv er inp ut B. 25 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF , STOP , 1.5 , G/ n . 26 Only for Analyz ers with Opti on 006: Press STO P , 3 , G/n . 27 Repeat Step 6 throu gh Step 9 to measure the s ource ...

  • Agilent Technologies 87020 - page 232

    6-66 Performanc e Tests – Opt ion 0 11 17. Rece iver Magnit ude Fre quency Re spons e (Opt ion 00 2 Only) for the r eceiver input A. Press MEA S , INPUT PORTS , A in Step 6 . 36 Repeat Step 11 thr ough Step 1 6 to measure the receiver wor st case 3nd harm o nic for the rece iver input A. In Cas e of Difficulty WAR NI N G These servicing instructi ...

  • Agilent Technologies 87020 - page 233

    6-67 Performance T ests – Option 011 17. Recei ver Ma gnitu de Fr equency Res ponse (Opti on 002 Only) Additio nal E quipmen t Requi red for O ption 00 6 Power Senso r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agilent 8 481A Procedure Source Harm onic s 1 Connec t t he equ ipm ent as show n in Figure 6-35 . F ...

  • Agilent Technologies 87020 - page 234

    6-68 Performanc e Tests – Opt ion 0 11 17. Rece iver Magnit ude Fre quency Re spons e (Opt ion 00 2 Only) Test R ecord. ” 8 Press B . Write the marker 1 rea ding, which app ears o n th e anal yzer displa y, in the “ Input B Val ue ” column o n the “ Performa nce Test Record. ” 9 On the ex terna l source , press 48 , MHz . R ecord the po ...

  • Agilent Technologies 87020 - page 235

    6-69 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 Performance Test Records - Opti on 011 The follow ing tables are to re cord t he pe rform ance test recor ds fo r each of the Agilent 8702D O ption 01 1 tests . T est 1. So urce Frequenc y Range and Accuracy CW Freq uency (MHz) Low er Li mit (MHz) Measur ed Val ue (MHz ...

  • Agilent Technologies 87020 - page 236

    6-70 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 2. Sourc e Power Rang e, Linearity , and Accu racy (Path Loss Ca lculations) CW Freq uency Sou rce O utp ut Power L evel (dBm) First Val ue (dB) Second Val ue (d B) Path Lo ss (dB ) 300 kHz +10 ________ _______ __ _______ ______ _______ _______ _ 20 MH z +10 ____ ...

  • Agilent Technologies 87020 - page 237

    6-71 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 + 1 + 9 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 3 + 7 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 5 + 5 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 7 + 3 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 9 + 1 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 11 ...

  • Agilent Technologies 87020 - page 238

    6-72 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 + 20 – 10 ___ _____ _ _______ _ _______ ± 0.5 ± 0.15 Option 006 CW Fre quency = 3 00 kHz + 13 – 3 _______ _ _ _______ _____ ___ ± 0. 5 ± 0.15 + 18 – 8 _______ _ _ _______ _____ ___ ± 0. 5 ± 0.15 CW Fre quency = 3 GHz + 13 – 3 _______ _ _ _______ _____ ___ ...

  • Agilent Technologies 87020 - page 239

    6-73 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 2. So urce Power , Range, Lin earity and Ac curacy (Power Level Ac curac y) CW Freq uency (M Hz) Path Loss (dB) Calib rat ed Power Level (dB ) Measu red Value (d B) Power Level Accurac y (dB) Spec. (dB) Meas. Uncer. (dB) So urce Output Powe r Level = +10 d Bm 0.3 ...

  • Agilent Technologies 87020 - page 240

    6-74 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 3. Recei ver Mini mum R Chann el Level CW Freq uency Specific ation (dB) Mark er Val ue (dB) M easur ement U ncerta inty (dB) 300 kHz < – 35 _______ _______ ______ ± 1.0 3.29 MHz < – 35 __________ _______ ___ ± 1.0 3.31 MHz < – 35 __________ ____ ...

  • Agilent Technologies 87020 - page 241

    6-75 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 4. Receiver Minim um R Chann el Level for External S ource Mode CW Freq uency (MHz) Frac-N VCO Lower Limit (MHz) Frac-N VCO Upper Limit (M Hz) Measur ed Val ue (MHz) Measur ement Uncer tainty 10 49 .496 50.496 __ ______ ____ N/A 20 37 .620 38.380 __ ______ ____ N ...

  • Agilent Technologies 87020 - page 242

    6-76 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 5. Receiver Cha nnel Noise Floor Level Freque ncy Rang e IF Band width Specifica tion (dBm) Calcu lated Value Measu rement Unce rtai nty Receiv er Chan nel A 300 kHz – 3.0 GHz 3 kHz – 90 ______ ______ N/A 300 kHz – 3.0 GHz 10 Hz – 110 ___ _______ __ N/A R ...

  • Agilent Technologies 87020 - page 243

    6-77 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 7. Receiver Mag nitude Frequency Response CW Freque ncy Power Mete r Read ing R Inpu t Power A Input Power B In put Power Greate st Differ ence Spec. (dB) Meas. Uncer. (dB) Example – 10.0 – 10.14 – 10.09 – 10.10 0.14 ± 1 ± 0.05 300 k Hz ___ ____ _______ ...

  • Agilent Technologies 87020 - page 244

    6-78 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 8. Receiver Phase Frequen cy Response Freque ncy Rang e Ratio Specif ication Measur ed Va lue Meas urement Unce rtaint y 300 kHz – 3 GHz A/R ± 3 ° _______ ______ ± 0.35 ° 300 kHz – 3 GHz B/R ± 3 ° ___________ __ ± 0.35 ° 300 kHz – 3 GHz A/B ± 3 ° ...

  • Agilent Technologies 87020 - page 245

    6-79 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 Option 006 R into A Cr ossta lk 3.0 GHz – 4.5 GHz – 82 _______ ____ ____ N/A 4.5 GHz – 6.0 GHz – 75 _______ ____ ____ N/A R into B Cr osstalk 3.0 GHz – 4.5 GHz – 82 _______ ____ ____ N/A 4.5 GHz – 6.0 GHz – 75 _______ ____ ____ N/A B into A Cr ossta lk ...

  • Agilent Technologies 87020 - page 246

    6-80 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 10. Receiver T race Noise CW Freq uency (GHz) Ratio Measured V alue Specif ication (rms) Measur ement Uncer tainty 3A / R ________ _______ _____ ≤ 0 .006 dB N/A 3B / R ________ _______ _____ ≤ 0 .006 dB N/A 3A / B ________ _______ _____ ≤ 0 .006 dB N/A 3A / ...

  • Agilent Technologies 87020 - page 247

    6-81 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 12. Receive r Magnitude Dyn amic Accu racy (1 of 2) Rece iver Input Power (dB) Agilent 8496A Setting (dB) Rece iver Chan nel A (dB) Agilent 8902A (dB) Magn itude Value (dB ) Spec. (dB) Meas . Uncer. (dB ) Channel A – 10 0 _________ ___ ______ ___ ______ ≤ 0.0 ...

  • Agilent Technologies 87020 - page 248

    6-82 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 – 90 80 _________ ___ ______ ______ ___ ≤ 0.680 ± 0. 180 – 100 90 ___ ______ ______ ___ ______ ___ ≤ 1.950 ± 0. 200 – 110 100 ______ ___ ______ ___ _________ ≤ 5.200 ± 0.28 0 Channel R – 10 0 _________ ___ ______ ___ ______ ≤ 0.075 ± 0. 010 – 20 1 ...

  • Agilent Technologies 87020 - page 249

    6-83 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 – 100 _________ ______ ___ ______ ___ _________ ≤ 16.00 N/A – 110 _________ ______ ___ ______ ___ _________ ≤ 51.50 N/A Channel B – 10 ________ _ _________ ___ ______ ______ ___ ≤ 0.80 N/A – 20 ________ _ _________ ___ ______ ______ ___ ≤ 0.40 N/A – 3 ...

  • Agilent Technologies 87020 - page 250

    6-84 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 14. Receiver Magni tude C ompression (1 of 2) CW Freq uency Sta rt Powe r (dBm) Stop Po wer (dBm) Measur ed Value (dB ) Specif ication (dB) Measur ement Uncer tainty Channel A 50 MHz _________ ______ ___ ______ ___ ≤ 0.32 N/A 1 GHz ___ ______ ___ ______ ___ ___ ...

  • Agilent Technologies 87020 - page 251

    6-85 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 5 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A 6 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A Channel R 4 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A 5 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A 6 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 3 ...

  • Agilent Technologies 87020 - page 252

    6-86 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 1 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A 2 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A 3 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A Option 006 Channel A 4 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A 5 GHz ___ ______ ___ ______ ___ ______ ≤ 5 ...

  • Agilent Technologies 87020 - page 253

    6-87 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 16. Source and Receiver Harmonics (Option 002 Only) (1 of 2) Test De scriptio n Ha rmonic Specific ation (dBc) Measureme nt Val ue Measu rement Unce rtaint y (dB) Sour ce Har monics 1.5 2nd < – 25 _ _______ _______ ± 1 1.0 3rd < – 25 _____ __________ ? ...

  • Agilent Technologies 87020 - page 254

    6-88 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 2B : 3 r d < – 30 _ _______ _______ ± 1 Receiv er Har monic s 3 B : 2nd < – 15 _____ _______ ___ ± 1 2B : 3 r d < – 30 _ _______ _______ ± 1 3 A: 2nd < – 15 _____ _______ ___ ± 1 2A : 3 r d < – 30 _____ __________ ± 1 T est 16. Source and ...

  • Agilent Technologies 87020 - page 255

    6-89 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 17. Receive r Magnitude Resp onse (Op t ion 002 Only) Analy zer Freque ncy Ext. Sour ce Freq uency Power Meter Value Input A Value Inpu t B Valu e Max. Dif f. Spec Spec. (dB) Meas . Uncer. (dB) 16 MHz 32 MHz _ ______ __ _____ ___ ____ _______ ± 1 ± 0.05 16 MHz ...

  • Agilent Technologies 87020 - page 256

    ...

  • Agilent Technologies 87020 - page 257

    7 If t he dis play does not light 7-2 If the fan does not run 7-3 If data entry ke ys don ’ t respond 7-3 If t here i s no RF sign al 7-4 Return ing the Instrum ent for Se rvice 7-5 Agilen t Technolog ies Service Offices 7-8 If Yo u Enco unte r a Prob lem ...

  • Agilent Technologies 87020 - page 258

    7-2 If You Encoun ter a Prob lem If You Encounter a Pr oblem If You Encounter a Problem If you hav e difficu lty whe n instal ling or using the Agil ent 8 702D, che ck the fol- lowi ng l ist of comm only e ncountered p roblems a nd tr oubles hoot ing pr oce- dures. Contact the nearest Agilen t T echno logies offi ce for servic e, if necess ary . A ...

  • Agilent Technologies 87020 - page 259

    7-3 If Y ou Enco unter a Probl em If the fan doe s not run WAR NI N G The power cord is conn ect ed to i ntern al capa cito rs tha t may rem ain live fo r 10 seconds af ter you disconne ct the co rd from the po wer supply. Figure 7-1. Line Fuse Remo val and Replacement WAR NI N G For co ntinued pr otec tion agai nst fire hazard , replace th e fuse ...

  • Agilent Technologies 87020 - page 260

    7-4 If You Encoun ter a Prob lem If ther e is no RF si gnal The “ entry o ff ” is ena bled a fter yo u press the ENTRY OFF key . T o retu rn to nor- mal entr y mode, pr ess any funct ion key that has a numeric para meter associ - ated w ith i t. For exam ple, ST ART . ❒ Check that none of the key s are mechan ically stuck. ❒ Check that the ...

  • Agilent Technologies 87020 - page 261

    7-5 If Y ou Enco unter a Probl em Returning the In stru ment for Se rvice Returning the Instrument for Service The instru ction s in this sec tion sho w yo u ho w to p roper ly return the i nstru - ment f or repair o r calibrati on. Always c all t he Agilent T echnol ogies I nstrument Suppo rt Center first to initi a te servi ce before retur ning y ...

  • Agilent Technologies 87020 - page 262

    7-6 If You Encoun ter a Prob lem Returni ng the Instrumen t for Service infor matio n sho uld b e ret urned with the inst rument. • Type of ser vice required. • Date instrum ent was ret urned for repair. • Descri ption of th e proble m: • Whet her prob lem is co nstant or i ntermi ttent. • Wheth er inst rument is temp erature-s ensiti ve. ...

  • Agilent Technologies 87020 - page 263

    7-7 If Y ou Enco unter a Probl em Returning the In stru ment for Se rvice Sealed Air Cor poration (Com merce, Cali fornia 90001). Air Cap looks like a plastic sh eet filled with air bubbl es. Use the pi nk (antistati c) Air Cap ™ to redu ce stat ic elect ricit y. Wra pping th e inst rument seve ral times i n this ma - teria l will prote ct the in ...

  • Agilent Technologies 87020 - page 264

    7-8 If You Encoun ter a Prob lem Agil ent Tech nologi es Se rvice Offic es Agilent Technologies Service Offices Befor e returning an instru ment for ser vice, call the Ag ilent T echnologi es Instrumen t Suppo rt Center at (80 0) 403-0801, visit th e T es t and Measu rement W eb Sites by Count ry page at http ://www .tm .agilent. com/tmo /countr y/ ...

  • Agilent Technologies 87020 - page 265

    Index Index- 1 A accuracy and range of frequency, 4-3 accuracy and range o f frequency (Option 011), 6-3 accuracy of power test, 4-6 Agilent o ffices, 7-8 B backup disk, 1-26 C cabinet , cleanin g, iv , 1-2 calibra tion coefic ients test, 4-34 care of cab inet, iv , 1- 2 che ckin g t he o perati on, 1-16 classification product, iv cleaning cabine t ...

  • Agilent Technologies 87020 - page 266

    Index -2 Index test port input fre quency response, 4-19 , 6-21 test port input impedanc e, 4-44 , 6-35 test port input noise floor level, 4-15 test port output frequency range and accu- racy, 4-3 test port output power acc uracy, 4-6 test port output power range and linearity, 4-8 , 6-5 test port receiver magnitude compress ion, 4-57 , 6-48 test p ...

  • Agilent Technologies 87020 - page 267

    Index- 3 Index printer type, 1-13 problems, data entry controls do not respond, 7-3 problems, power-up display lights, but fan does not st art, 1-7 , 7-3 problems, RF output no RF signal at ei ther PORT 1 or PORT 2 , 7-4 procedures calibration coefficients, 4-34 external source mode frequency range, 4-5 minimum R cha nnel level, 4-10 , 6-9 , 6-12 s ...

  • Agilent Technologies 87020 - page 268

    Index -4 Index test port output power range and linearity, 4-8 , 6-5 test port receiver magnitude compress ion, 4-57 , 6-48 test port receiver ma gnitude dynamic accu- racy, 4-48 , 6-39 test port receiver phase compression, 4-59 , 6-56 test port receiver phase dynamic accuracy, 4-55 , 6-47 syste m trace no ise test (with op tion 00 6), 4-42 syst em ...

Manufacturer Agilent Technologies Category Stroller

Documents that we receive from a manufacturer of a Agilent Technologies 87020 can be divided into several groups. They are, among others:
- Agilent Technologies technical drawings
- 87020 manuals
- Agilent Technologies product data sheets
- information booklets
- or energy labels Agilent Technologies 87020
All of them are important, but the most important information from the point of view of use of the device are in the user manual Agilent Technologies 87020.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Agilent Technologies 87020, service manual, brief instructions and user manuals Agilent Technologies 87020. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Agilent Technologies 87020.

Similar manuals

A complete manual for the device Agilent Technologies 87020, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Agilent Technologies 87020 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Agilent Technologies 87020.

A complete Agilent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Agilent Technologies 87020 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Agilent Technologies 87020, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Agilent Technologies 87020, that we can find in the current document
3. Tips how to use the basic functions of the device Agilent Technologies 87020 - which should help us in our first steps of using Agilent Technologies 87020
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Agilent Technologies 87020
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Agilent Technologies 87020 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Agilent Technologies 87020?

Use the form below

If you did not solve your problem by using a manual Agilent Technologies 87020, ask a question using the form below. If a user had a similar problem with Agilent Technologies 87020 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)