Manual Emerson 752I

172 pages 4.85 mb
Download

Go to site of 172

Summary
  • Emerson 752I - page 1

    Katana ® 752i: Intelligent CompactPCI Blade for cPSB User’s Manual from Emerson Network Power ™ Embedded Computing April 2008 ...

  • Emerson 752I - page 2

    The informatio n in this manu al has been che cked and is beli eved to be accu rate and reli - able. HOWEVER, NO RESPONSIBILITY IS ASSUMED BY EMERSON NETWORK POWER, EMBEDDED COMPUTING FOR ITS USE OR FOR ANY INACCURACIES. S pecifications are sub- ject to change without noti ce. EMERSON DOES NOT ASSUME ANY LIABILIT Y ARISING OUT OF USE OR OTHER APPLI ...

  • Emerson 752I - page 3

    10006024-04 Katana ®752i User’s Manual i Regulatory Agency Warnings & Notices The Emerson Katana752i meets the requi remen ts set forth by the F ederal Communicati ons Commission (FCC) in Ti tle 47 of the Code of Federal Regulations. T he following informatio n is provided as required by this agency. This device complies with part 15 of the ...

  • Emerson 752I - page 4

    (continued) Katana ®752i User’s Manual 10006024-04 ii EC Declaration of Conformity According to EN 45014:1998 Manufacturer’s Na me: Emerson Network Power Embedded Computing Manufacturer’s Address: 8310 Excelsior D rive Madison, Wisc onsin 5371 7 Declares that th e following produ ct, in accordance wi th the require ments of 2004/108 /EEC, EM ...

  • Emerson 752I - page 5

    10006024-04 Katana ® 752i User’s Manual iii Contents 1O v e r v i e w Components and Features . . . . . . . . . . . 1-1 Functional Overv iew . . . . . . . . . . . . . . . . 1-4 Additional I nformation . . . . . . . . . . . . . . 1-5 Product Certifi cation . . . . . . . . . . . . . 1-5 RoHS Compliance. . . . . . . . . . . . . . . . 1-6 Terminolog ...

  • Emerson 752I - page 6

    Katana ® 752i User’s Manual 10006024-04 iv (blank page ) 8L o c a l P C I B u s PCI Enumeration . . . . . . . . . . . . . . . . . . . . .8-1 PCI ID Select and Interr upts . . . . . . . . . . .8-1 Geographical Addr essing . . . . . . . . . . . . .8-2 PCI Bus Control Signal s . . . . . . . . . . . . . . .8-2 9 PTMC Interface PTMC Installation . . ...

  • Emerson 752I - page 7

    Contents (continued) 10006024-04 Katana ® 752i User’s Manual v JFFS2 File Systems. . . . . . . . . . . . . . . . . 15-12 ls . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-12 fsinfo. . . . . . . . . . . . . . . . . . . . . . . . .15-12 fsload . . . . . . . . . . . . . . . . . . . . . . . .15-12 chpart . . . . . . . . . . . . . . . . . ...

  • Emerson 752I - page 8

    Katana ® 752i User’s Manual 10006024-04 vi (blank page ) ...

  • Emerson 752I - page 9

    10006024-04 Katana ® 752i User’s Manual vii Figures Figure 1-1: General System Blo ck Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Figure 2-1: Katana®752i Front P anel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Figure 2-2: Co ...

  • Emerson 752I - page 10

    Katana ® 752i User’s Manual 10006024-04 viii (blank page ) ...

  • Emerson 752I - page 11

    10006024-04 Katana ® 752i User’s Manual ix Tables Table 1-1: Regulatory Agenc y Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Table 1-2: Technical References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 Table 2-1: Circuit ...

  • Emerson 752I - page 12

    Tables (continued) Katana ® 752i User’s Manual 10006024-04 x Table 11-17: Event Message Fo rmat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-20 Table 11-18: System Firmware P rogress OEM Event Dat a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-21 Table 12-1: HSL PL ...

  • Emerson 752I - page 13

    10006024-04 Katana ® 752i User’s Manual i Registers Register 4-1: 750GL Hardware Imp lementation Dependent, HID0 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Register 4-2: 750GL Hardware Imp lementation Dependent, HID1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Register 4-3: 750GL Hardware Imp lementation Dependent, H ...

  • Emerson 752I - page 14

    Katana ® 752i User’s Manual 10006024-04 ii (blank page ) ...

  • Emerson 752I - page 15

    10006024-04 Katana ®752i User’s Manual 1-1 Section 1 Overview The Emerson Katana ® 752i is an intelligent input/output (I/O) processing blade for use in a CompactPCI backplane. It is compatible wi th the CompactPCI Pa cket-Switched Backpl ane (cPSB) and h as two PCI Te lecom Mezzan ine Card (PTMC) sites that can support two tele- communications ...

  • Emerson 752I - page 16

    Overview: Components and Features Katana ®752i User’s Manual 10006024-04 1-2 SDRAM: The Katana®75 2i allows for a 7 2-bit Small-Out line Dual In-Lin e Memory Module (SO- DIMM) of up to two gi gabytes to su pport th e CPU. (Please contact Emerso n for the avail- ability of one- and two-gigabyte SO-DIMMs.) Th is SDRAM operates at a speed of up to ...

  • Emerson 752I - page 17

    Overview: Components and Features 10006024-04 Katana ®752i User’s Manual 1-3 PTMC Sites: The Katana®752 i has two standard PC I Telecom Mezza nine Card (PTMC ) slots, which allow for the use of two compa tible PTMC boards, such as the Emerson PM/3Gv t elecommunica- tions interface card. (Refer to the PM/3Gv User’s Manual for details on the P ...

  • Emerson 752I - page 18

    Overview: Functional Ov erview Katana ®752i User’s Manual 10006024-04 1-4 FUNCTIONAL OVERVIEW The following block diagram provi des a fu nctional overview for the Kat ana®752i. Figure 1-1: General System Block Diagram J1 J2 J3 cPSB & I/O Marvell D-III System Controller 32/64/128 MB Flash 256/512MB 1GB/2GB DDR SDRAM 512KB Socketed Flash PMC ...

  • Emerson 752I - page 19

    Overview: Additional Information 10006024-04 Katana ®752i User’s Manual 1-5 ADDITIONAL INFORMATION This section lists t he Katana®752i hardware ’s regulatory certificat ions and briefly d iscusses the terminology and notat ion conventions used in this manual. It also lists general technical references. Mean time between failures (MTBF) has be ...

  • Emerson 752I - page 20

    Overview: Additional Information Katana ®752i User’s Manual 10006024-04 1-6 Emerson maintains test reports that provide specific informati on regarding the methods and equipment used in compliance testing. Unshield ed external I/O cables, loose screws, or a poorly grounded chassis may adversel y affect the Katana®752i hardware’s ability to co ...

  • Emerson 752I - page 21

    Overview: Additional Information 10006024-04 Katana ®752i User’s Manual 1-7 Table 1-2: Technical References Device/Interface :T y p e : D o c u m e n t : 1 CompactPCI CompactPCI ® Specification (PCI Industrial Computers Manufacturer s Group, PICMG ® 2.0 R3.0, Oct. 1, 1999) Hot Swap Specification (PICMG ® 2.1 R2.0, Jan. 17, 20 01) System Manag ...

  • Emerson 752I - page 22

    Overview: Additional Information Katana ®752i User’s Manual 10006024-04 1-8 Ethernet BCM5461S BCM5461S 10/100/1000Base-T Gigabit Et hernet Transceiver Advance Data Sheet (Broadcom Corp., 5461S-DS04-R, April 27, 200 4) http://www.br oadcom.com 82544EI 82544EI Gigabit Eth ernet Controller Datasheet and Hardware Design Guide; Application Note (AP-4 ...

  • Emerson 752I - page 23

    Overview: Additional Information 10006024-04 Katana ®752i User’s Manual 1-9 If you have questi ons, please cal l Emerson Technic al Support at 1-800- 327-1251, visit the web site at http://www.emersonembedde dcomputing.com, o r send e-mail to support@a rtesyncp.com . H.110 T8110 Ambassador ® T8110 PCI-Based H.100/H.110 Switch and Packet Payload ...

  • Emerson 752I - page 24

    Katana ®752i User’s Manual 10006024-04 1-10 (blank page ) ...

  • Emerson 752I - page 25

    10006024-04 Katana ® 752i User’s Ma nual 2-1 Section 2 Setup This chapter describes the physical layout of the boa rds, the setup process, and how to check for proper operat ion once the boards have been inst alled. This chapt er also includes troubleshooting, service, and warranty information. ELECTROSTATIC DISCHARGE Before you begin the setup ...

  • Emerson 752I - page 26

    Setup: Katana®752i Circuit Board Katana ® 752i User’s Manual 10006024-0 4 2-2 Figure 2-1: Katana ® 752i Front Panel PMC Site #2 PMC Site #1 EIA-232 Serial Port Reset Switch Programmable LEDs 14, Green Speed LED, ETH4 GbE Port, 82544EI (ETH4) Fault LED, Red Activity LED, ETH4 Speed LED, ETH3 Activity LED, ETH3 GbE Port, MV64460 (ETH3) Hot Sw ...

  • Emerson 752I - page 27

    Setup: Katana®752i Circuit Board 10006024-04 Katana ® 752i User’s Ma nual 2-3 Figure 2-2: Component Map, Top (Rev. 03) J6 CR1 U15 C98 C62 C97 C88 C66 C71 C75 U34 F4 F3 C9 C124 C123 C8 Y2 C93 C114 C115 C94 C85 Y1 C122 C638 C113 C112 C120 C116 C119 C118 C5 C4 C43 C42 C52 C50 C14 C99 C61 C58 C91 U23HC C546 C548 C552 C553 C550 C544 C543 C540 C541 C ...

  • Emerson 752I - page 28

    Setup: Katana®752i Circuit Board Katana ® 752i User’s Manual 10006024-0 4 2-4 Figure 2-3: Component Map, Bottom (Rev . 03) C171 C347 C641 C627 C626 C657 C193 C182 C400 C386 C414 C472 C439 C441 C456 C454 C420 C432 C708 C709 C710 C707 C661 C132 C127 C126 C125 C508 C587 C640 C662 C637 C639 C669 C656 C458 C150 C216 C412 C403 C422 C455 C470 C655 C66 ...

  • Emerson 752I - page 29

    Setup: Katana®752i Circuit Board 10006024-04 Katana ® 752i User’s Ma nual 2-5 Figure 2-4: Jumper, Fuse, and Switch Locations, Top COPYRIGHT 2004 10006008-00 REV A F4 F3 F1 F2 J3 J4 J5 J22 J21 J24 J23 J12 J1 1 J1 J2 J14 J13 P1 CR1 P2 JP2 JP1 SW1 SW1  Reset Switch F4  Fuse for 5-V olt Supply to RTM, 2.5A F3  Fuse for 3.3-Volt Supply to R ...

  • Emerson 752I - page 30

    Setup: Katana®752i Circuit Board Katana ® 752i User’s Manual 10006024-0 4 2-6 Figure 2-5: Fuse, and LED Locations, Bottom C171 C347 C641 C627 C626 C657 C193 C182 C400 C386 C414 C472 C439 C441 C456 C454 C420 C432 C708 C709 C710 C707 C661 C132 C127 C126 C125 C508 C587 C640 C662 C637 C639 C669 C656 C458 C150 C216 C412 C403 C422 C455 C470 C655 C660 ...

  • Emerson 752I - page 31

    Setup: Katana®752i Circuit Board 10006024-04 Katana ® 752i User’s Ma nual 2-7 Identification Numbers Before you install t he Katana ® 752i circu it board in a syste m, you should record the follow- ing information: ❐ The board serial number: ___________ __________ _____________ __________ . The board serial n umber appears on a b ar code sti ...

  • Emerson 752I - page 32

    Setup: Katana®752i Circuit Board Katana ® 752i User’s Manual 10006024-0 4 2-8 J4 : J4 is a 90-pin connector that routes co mputer telephony (CT) bus signals to the Compact- PCI backplane. See Chapter for pinouts. J5: J5 is a 110-pin conn ector that routes user in put/output sign als directly from the J24 co nnec- tor at PTMC expansion site #2. ...

  • Emerson 752I - page 33

    Setup: Katana®752i Setup 10006024-04 Katana ® 752i User’s Ma nual 2-9 KATANA ® 752I SETUP You need the following item s to set up and chec k the operation of th e Emerson Katana ® 752i. ❐ Emerson Katana ® 752i boa rd ❐ Card cage and p ower supply ❐ Serial interface cable (EIA- 232) ❐ Terminal Save the antistati c bag and box for futu ...

  • Emerson 752I - page 34

    Setup: Troubleshooting Katana ® 752i User’s Manual 10006024-0 4 2-10 Power Requirements The Emerson Katana ® 752 i circuit board typically requires abou t 35 watts of power when performing a si mple memory test with no PMC/PT MC modules insta lled. The exact p ower requirements for the Katana ® 752i circ uit board depend upon the specific conf ...

  • Emerson 752I - page 35

    Setup: Troubleshooting 10006024-04 Katana ® 752i User’s Ma nual 2-11 moninit <four-digit board serial number> noburn Executing the above comma nd will set all en vironment variables to defau lt values and erase any user-adde d environment variable s. Please see “Envir onment Parameter Commands” on page 15-18, for additional information ...

  • Emerson 752I - page 36

    Setup: Troubleshooting Katana ® 752i User’s Manual 10006024-0 4 2-12 Please put the RMA number on the outside of the package so we can handle your problem efficiently. O ur service departmen t cannot ac cept material received without an RMA num- ber. ...

  • Emerson 752I - page 37

    10006024-04 Katana ® 752i User’s Ma nual 3-1 Section 3 Reset Logic This chapter provides a system-l evel ov erview of the reset logic for th e Katana ® 752i. It also describes the various reset sources. GENERAL OVERVIEW The Katana ® 752i uses discrete logic on a programmable lo gic device (PLD) to impleme nt the reset circuitry. Fig. 3 -1 on t ...

  • Emerson 752I - page 38

    Reset Logic: General Overview Katana ® 752i User’s Manual 10006024-0 4 3-2 Figure 3-1: Katana ® 752i Reset Diagram F r o n t P a n e l P u s h B u t to n 2 . 5 V I P M I P o w e r O S C _ E N E n a b le BCM5221 r e s e t KS8721CL r e s e t BCM5221 r e s e t BCM5221 r e s e t BCM5461 r e s e t T8110 TSI r e s e t Soldered Flash R P PMC Site 1 r ...

  • Emerson 752I - page 39

    Reset Logic: Reset Sources 10006024-04 Katana ® 752i User’s Ma nual 3-3 RESET SOURCES The Katana ® 752i circuit board can be reset from the following sources: • Power-On Reset (POR) circuitr y •C o m p a c t P C I R e s e t • Power Monitor Reset • 750GL Processor Reset (JTAG header) • Remote IP MI Reset •F r o n t P a n e l R e s e ...

  • Emerson 752I - page 40

    Reset Logic: Reset Sources Katana ® 752i User’s Manual 10006024-0 4 3-4 Figure 3-2: 750GL Reset Logic Soldered Flash flash_wp MV64460 sysrst pci0_rst pci1_rst gt_wde COP/JTAG hreset sreset trst Device Bus PLD cop_hreset cop_ sreset cop_tr st pmc_rst gt_wde gt_pci0 gt_pc i1 start_lrst cpu_hre set cpu_sre set cpu_trst fl_rp gt_sysrst 750GX hreset ...

  • Emerson 752I - page 41

    10006024-04 Katana ® 752i User’s Ma nual 4-1 Section 4 Processor The Katana ® 752i processor complex consists of a processor and a system controller/PCI bridge devi ce (see Chapte r ) with associated memory and inp ut/output inte rfaces. The pro- cessor complex supports soldered and socket ed user Flash memo ry, DDR SDRAM, an EIA- 232 serial co ...

  • Emerson 752I - page 42

    Processor: Processor Overview Katana ® 752i User’s Manual 10006024-0 4 4-2 Figure 4-1: 750GL Block Diagram Physical Memory Map The Katana ® 752i monitor ( see Chapter ) initiali zes the devices required to configure th e memory map for the 750GL bus. T he following figure sho ws the 750GL physical memory map. Completion System Unit Dispatch BHT ...

  • Emerson 752I - page 43

    Processor: Processor Overview 10006024-04 Katana ® 752i User’s Ma nual 4-3 Figure 4-2: 750GL Memory Map Device B us PLD Regist ers E800,0000 Flash S ocket F820,0000 FLASH (up to 128 MB) F810,0000 MV 64460 Regist ers F800,0000 Reserved C000,0000 E000,0000 F808,0000 Reserved F811,0000 cPCI Memory Space cPCI I/O Space FF80,0000 Boot Mirror FFFF,FFF ...

  • Emerson 752I - page 44

    Processor: Processor Reset Katana ® 752i User’s Manual 10006024-0 4 4-4 This table summarizes the physica l addresses for the 750GL on the Katana ® 752i board and provides a reference to mo re detailed information. Table 4-2: Katana ® 752i Address Summary PROCESSOR RESET Circuitry on the Katana ® 752i resets the processor and the board. Pl ea ...

  • Emerson 752I - page 45

    Processor: Processor Initialization 10006024-04 Katana ® 752i User’s Ma nual 4-5 Hardware I mplementatio n Dependent 0 Register The Hardware Imple mentation Depe ndent 0 Regist er (HID0) contains bi ts for CPU-specific features. Most of these bits are cleared on initi al power-up of the Katana ® 752i. Please refer to the IBM PowerPC documentati ...

  • Emerson 752I - page 46

    Processor: Processor Initialization Katana ® 752i User’s Manual 10006024-0 4 4-6 BTIC: Branch Target Instru ction Cache enable. ABE: Address Broadc ast Enable (for cac he ops, eie io , sync ). BHT: Branch History Table enable. NOOPTI: No-op the dcbt / dcbst instruction s. Hardware I mplementatio n Dependent 1 Register The 750GL includes two phas ...

  • Emerson 752I - page 47

    Processor: Processor Initialization 10006024-04 Katana ® 752i User’s Ma nual 4-7 PR0: PLL0 Range selec t bits. PC1: PLL1 Configurat ion bits. PRI: PLL1 Range bits. Hardware I mplementatio n Dependent 2 Register Parity is implem ented for the fo llowing array s: I-Cache, I-Tag, D-Cache , D-Tag, and L2 Tag. Status bits are set wh en a pari ty erro ...

  • Emerson 752I - page 48

    Processor: Exception Handling Katana ® 752i User’s Manual 10006024-0 4 4-8 EXCEPTION HANDLING Each CPU exception type transfers co ntrol to a different address in the vector tabl e. The vector table normally occupies the first 20 00 bytes of RAM (with a base address of 0000,0000 16 ) or ROM (with a base address of F800,0000 16 ). A n un a ss i g ...

  • Emerson 752I - page 49

    Processor: Exception Processing 10006024-04 Katana ® 752i User’s Ma nual 4-9 EXCEPTION PROCESSING When an excepti on occurs, the addr ess saved in Machine S tatus Save/Resto re register 0 (SRR0) helps d etermine where instruction pro c essing should resume when the exception handler returns control to the interrupted process . Machine St atus Sa ...

  • Emerson 752I - page 50

    Processor: Exception Processing Katana ® 752i User’s Manual 10006024-0 4 4-10 FP: Floating-Poi nt available . This bit is set on initial p ower-up. 0 = Prevent s floating-point instructions dispatch ( loads, stores, moves). 1 = Executes floating-poin t instructions. ME: Machine check Enable. 0 = Machine check exceptio ns disabled. 1 = Machine ch ...

  • Emerson 752I - page 51

    Processor: Cache Memory 10006024-04 Katana ® 752i User’s Ma nual 4-11 CACHE MEMORY The 750GL proc essor provides bot h level 1 (L1) and level 2 ( L2) cache memory. T his section describes this memory. L1 Cache The 750GL p rocessor has separa te, on-chip, 32 -kilobyte, Level 1 (L1) instruc tion and data caches with eight-way, set-associative tran ...

  • Emerson 752I - page 52

    Processor: Cache Memory Katana ® 752i User’s Manual 10006024-0 4 4-12 L2DO: L2 Data-Only. Setting this bit inhibits the ca ching of instructio ns in the L2 cache. All accesses from the L 2 instruction cache are treated as cache-in hibited by the L2 cache. L2I: L2 global In validate. Setting this bit invalidates the L 2 cache gl obally by clearin ...

  • Emerson 752I - page 53

    Processor: JTAG/COP Headers 10006024-04 Katana ® 752i User’s Ma nual 4-13 JTAG/COP HEADERS The 750GL CPU provi des a dedicated user-accessi ble test access port (TAP) that is fully compatible with the IEEE 1149.1 Stand ard Test Access Port and Boundary Scan Architec- ture. The intern al common-on-chip (COP) debug processor al lows access to inte ...

  • Emerson 752I - page 54

    Processor: JTAG/COP Headers Katana ® 752i User’s Manual 10006024-0 4 4-14 15 CHKSTPO* Output Checkstop (halt ed) indication (see also Checkstop LED indicator, CR31, in Fig. 2-5 ) 16 GND — Ground Pin: Signal: I/O: Description: (continued) ...

  • Emerson 752I - page 55

    10006024-04 Katana ® 752i User’s Ma nual 5-1 Section 5 System Controller The Katana ® 752i processor complex consists of a processor (se e Chapter ) and a sy stem controller/PCI bridge devi ce with associated memory and input /output interfaces. Th is chapter describes the Marvell MV64460 system co ntroller/PCI bridge device implement a- tion. ...

  • Emerson 752I - page 56

    System Controller: CPU Interface Katana ® 752i User’s Manual 10006024-0 4 5-2 Figure 5-1: MV64460 Block Diagram CPU INTERFACE CPU interface featu res include: • 32-bit address and 64-bit data buses • Support for Symmet rical Multi-Proces sing (SMP) in both 60x and MPX bus m odes • Support for up to four slave devices on the same 60x bus ? ...

  • Emerson 752I - page 57

    System Controller: SDRAM Controller 10006024-04 Katana ® 752i User’s Ma nual 5-3 1 Read the CPU Configuratio n register. This guaran tees that all previous t ransactions in the CPU interface pipe are flushed. 2 Program the register to its new value. 3 Read polling of the register unt il the new data is being read. Caution: Setting the CPU Config ...

  • Emerson 752I - page 58

    System Controller: Internal (IDMA) Controller Katana ® 752i User’s Manual 10006024-0 4 5-4 INTERNAL (IDMA) CONTROLLER Each of the four DMA engines c an move data between any source and any desti nation, such as the SDRAM, device, PCI_0, or CPU bus. Th ese engines optimiz e system performance by moving large amounts of data wi thout signif icant ...

  • Emerson 752I - page 59

    System Controller: PCI Interface 10006024-04 Katana ® 752i User’s Ma nual 5-5 PCI Identification The Katana ® 752i has been assigne d the following P CI identifica tion numbers. Table 5-1: PCI Identification Values PCI Read/Write The MV64460 bec omes a PCI bus master when the CPU, IDMA, or MPSC SDMA s initiate a bus cycle to a PCI device. Conve ...

  • Emerson 752I - page 60

    System Controller: Doorbell Registers Katana ® 752i User’s Manual 10006024-0 4 5-6 monitor the state of th e PCI bus INTA* —INTD* signals (P CI1 only). The MV 64460 contain s registers that control th e masking, unmask ing, and priority of th e PMC interrupts as i nputs to the processor. DOORBELL REGISTERS The MV64460 uses the doorbell registe ...

  • Emerson 752I - page 61

    System Controller: On-Card Memory 10006024-04 Katana ® 752i User’s Ma nual 5-7 ON-CARD MEMORY The Katana ® 752i has various types of on-card m e mory to support the MV 64460 system controller and t he 750GL proce ssor. It has user Flash, SDRAM for data storage, and several serial EEPROMs for non-volatile memory storage. The following subse ctio ...

  • Emerson 752I - page 62

    System Controller: I2C Interface Katana ® 752i User’s Manual 10006024-0 4 5-8 EEPROMs The MV64460 u ses an 8-kilob yte serial EEPROM a t hex location 53 16 on the I 2 C bus to store configuration data . Also, the MV6446 0 provides a second 8-ki lobyte serial EEP ROM at hex location A6 16 on the I 2 C bus to prov ide additional non-vol atile info ...

  • Emerson 752I - page 63

    System Controller: I2C Interface 10006024-04 Katana ® 752i User’s Ma nual 5-9 Figure 5-2: I 2 C Inte rface Diagram 0xA4 MV64460 i n iti a liz a tio n ROM 0xA6 NVRAM Co n fig ura ble a dd r ess th r o u gh soft war e co n t r ol Qlogic Zi r co n PM IPMI Co n t r olle r Co n fig ura ble a dd r ess th r o u gh soft war e co n t r ol Ma r vell MV644 ...

  • Emerson 752I - page 64

    System Controller: GPIO Signal Definitions Katana ® 752i User’s Manual 10006024-0 4 5-10 GPIO SIGNAL DEFINITIONS The MV64460 system co ntroller on the Katana ® 752i has 32 general-purpose input output (GPIO) pins that are used for variou s purpos es. The following table describ es the GPIO pin assignments. Table 5-3: GPIO Signals Definitions Pi ...

  • Emerson 752I - page 65

    System Controller: Console Serial Port 10006024-04 Katana ® 752i User’s Ma nual 5-11 CONSOLE SERIAL PORT The processo r comp lex on the Katana ® 752i has an asy nchronous console serial port on the front panel. This port operates at EIA-232 signa l levels, but does not provide any han dshak- ing functionality. Th e connector for the front panel ...

  • Emerson 752I - page 66

    Katana ® 752i User’s Manual 10006024-0 4 5-12 (blank page ) ...

  • Emerson 752I - page 67

    10006024-04 Katana ® 752i User’s Ma nual 6-1 Section 6 Device Bus PLD The processor comple x on the Katana ® 752i has a programmable logic d evice (PLD) t hat provides control log ic for the 750GL device bus. Th is PLD implements variou s registers relating to reset cont rol, interrupt handling, product id entification, PCI enumerat ion, and bo ...

  • Emerson 752I - page 68

    Device Bus PLD: Interrupt Registers Katana ® 752i User’s Manual 10006024-0 4 6-2 Register 6-2: Reset Command SCL: Direct control for I 2 C clock signal: 1=Tri-states the PLD 0=Drives logic low SDA: Direct control for I 2 C data signal: 1=Tri-states the PLD 0=Drives logic low PCI0 : PCI0 reset status, as se t by JP1, pins 7- 8; software should no ...

  • Emerson 752I - page 69

    Device Bus PLD: Product Identification 10006024-04 Katana ® 752i User’s Ma nual 6-3 SREN: PCI SERR Enable interrupt routed from PCI SERR to MV6446 0: 1=Enabled to generat e an interrupt 0=Disabled ( default) PREN: PCI PERR Enable interrupt rout ed from PCI PERR to M V64460: 1=Enabled to generat e an interrupt 0=Disabled ( default) The Interrupt ...

  • Emerson 752I - page 70

    Device Bus PLD: Revision Registers Katana ® 752i User’s Manual 10006024-0 4 6-4 Register 6-6: EReady ERdy: Monarch (read): 1=PCI devices ar e ready to be enumerated 0=PCI devices not ready to be enumera ted Non-Monarc h (write): 1=PMC is ready to be enumerated 0=PMC is n ot ready to be e numerated REVISION REGISTERS The Katana ® 752i device bus ...

  • Emerson 752I - page 71

    Device Bus PLD: Board Configuration Registers 10006024-04 Katana ® 752i User’s Ma nual 6-5 Note: Board Configuration 2 register is not implemente d in the Katana ® 752i. Register 6-9: Board Configuration 3. cPCI: cPCI bus status indication: 1=cPCI bus is d isabled (held in reset) (default ) 0=cPCI bus is enabled Mon: Monarch indication: 1=Katan ...

  • Emerson 752I - page 72

    Device Bus PLD: Other Registers Katana ® 752i User’s Manual 10006024-0 4 6-6 OTHER REGISTERS The IPMI Port Select register at hex loca tion F820,E000 16 allows access to the IPMI inter- face, as follows. Register 6-12: IPMI Port Select PORT_SEL: IPMI Port Selection: Allow processor access to the IPMI controller and t emperature sensors 1=Disable ...

  • Emerson 752I - page 73

    10006024-04 Katana ® 752i User’s Ma nual 7-1 Section 7 Real-Time Clock The processor complex on the Katana ® 752i has a stan dard real-ti me clock (RTC ), consistin g of an M41T00 device from STM icroelectronics. The M 41T00 has an i ntegrated year-2000- compatible RTC, power sense circuitry, a nd us es eight bytes of non-volatile RAM for th e ...

  • Emerson 752I - page 74

    Real-Time Clock: Clock Operation Katana ® 752i User’s Manual 10006024-0 4 7-2 1 Seconds register 2 Minutes register 3 Century/Hours register 4 Day register 5 Date register 6 Month register 7 Years register 8 Control register The M41T00 clock co ntinually monitors the suppl y voltage (Vcc) for an out of tolerance condition . If Vcc falls belo w s ...

  • Emerson 752I - page 75

    Real-Time Clock: Clock Operation 10006024-04 Katana ® 752i User’s Ma nual 7-3 ST: Stop bit 1=Stops t he oscill ator 0=Restarts the oscillator within one second CEB: Century Enable Bit 1=Causes CB to toggle eith er from 0 to 1 or from 1 to 0 at the turn of th e century 0=CB will not toggle CB: Century Bit Day: Day of the week Date: Day of the mon ...

  • Emerson 752I - page 76

    Katana ® 752i User’s Manual 10006024-0 4 7-4 (blank page ) ...

  • Emerson 752I - page 77

    10006024-04 Katana ® 752i User’s Ma nual 8-1 Section 8 Local PCI Bus The Katana ® 752i utilizes the Periphera l Component In terconnect (PCI) bus a s the interface between the 750GL proc essor complex, PCI Telecom Me zzanine Card (PTMC) sites, optional T8110 ti me slot interchanger ( TSI), and 82544 Ethernet media access controller (MAC). The K ...

  • Emerson 752I - page 78

    Local PCI Bus: Geographical Addressing Katana ® 752i User’s Manual 10006024-0 4 8-2 Table 8-1: ID Select Connections The T8110 TSI conne cts to INTD. The MV64 460 system controlle r connects to INTA. The Ethernet MAC connects to IN TD. The PCI devi ces on the PTMC module(s) use the following connections. Table 8-2: Interrupt Connections for Kata ...

  • Emerson 752I - page 79

    Local PCI Bus: PCI Bus Control Signals 10006024-04 Katana ® 752i User’s Ma nual 8-3 ACK64*, REQ64*: These sustained thre e-state output sign als tell a 64-bit PCI device whether to use the 64-bit or the 32-bit data wi dth. Since t he Katana ® 752i is a 32-b it board, these sig nals are tied off to indicate the 32-bit da ta width. AD00-AD31: ADD ...

  • Emerson 752I - page 80

    Local PCI Bus: PCI Bus Control Signals Katana ® 752i User’s Manual 10006024-0 4 8-4 PAR: PARITY. This is even parity ac ross AD00-AD31 and C/BE 0-C/BE3*. Parity generat ion is required by al l PCI agents. Th is three-state signa l is stable and va lid one clock afte r the address phase, and one clock after the bus master indicates that it is rea ...

  • Emerson 752I - page 81

    10006024-04 Katana ® 752i User’s Ma nual 9-1 Section 9 PTMC Interface The Katana ® 752i Peripheral Compone nt Interconne ct (PCI) inte rface supports two PC I Telecom Mezzan ine Card (PTMC ) expansion sites. T his chapter des cribes how to inst all PTMC modules and provi des additional informat ion about the P TMC signals. Each PTMC site can co ...

  • Emerson 752I - page 82

    PTMC Interface: PTMC Installation Katana ® 752i User’s Manual 10006024-0 4 9-2 The following procedure describes how to attach a PTMC module to the Katana ® 752i base- board: 1 Remove the scre ws from the st andoffs on the PTMC module. 2 Hold the module at an angle and gentl y slide the facep late into the op ening on the baseboa rd. 3 Align th ...

  • Emerson 752I - page 83

    PTMC Interface: PTMC Connector Pinouts 10006024-04 Katana ® 752i User’s Ma nual 9-3 PTMC CONNECTOR PINOUTS PCI expansion site #1 has fo ur 64-pin conne ctors, J11— J14 (see Fi g. 2-2 on page 2-3 for con- nector locations) . Table 9-1 shows the pin assignments. Table 9-1: J1x PTMC Connector Pin Assignments Pin J11 J12 J1 3 J14 1 TCK POS_12V MDI ...

  • Emerson 752I - page 84

    PTMC Interface: PTMC Connector Pinouts Katana ® 752i User’s Manual 10006024-0 4 9-4 35 GND TRDY* CT_D14 J3_A7 36 IRDY* +3.3V no connection J3_E6 37 DEVSEL* GND CT_D12 J3_D6 38 +5V STOP* GND J3_C6 39 GND PERR* PTENB* J3_B6 40 LOCK* GND no connection J3_A6 41 SDONE* +3.3V GND J3_E5 42 SBO* SERR* NETREF1 J3_D5 43 PAR CBE1* CT_C8B J3_C5 44 GND GN D ...

  • Emerson 752I - page 85

    PTMC Interface: PTMC Connector Pinouts 10006024-04 Katana ® 752i User’s Ma nual 9-5 PCI expansion site #2 has fo ur 64-pin conne ctors, J21— J24 (see Fi g. 2-2 on page 2-3 for con- nector locations) . Table 9-2 shows the pin assignments. Table 9-2: J2x PTMC Connector Pin Assignments Pin J21 J22 J2 3 J24 1 TCK POS_12V MDIO J5_E13 2 NEG_12V PMC2 ...

  • Emerson 752I - page 86

    PTMC Interface: PTMC Connector Pinouts Katana ® 752i User’s Manual 10006024-0 4 9-6 37 DEVSEL* GND CT_D12 J5_D6 38 +5V STOP* GND J5_C6 39 GND PERR* PTENB* J5_B6 40 LOCK* GND no connection J5_A6 41 SDONE* +3.3V GND J5_E5 42 SBO* SERR* NETREF1 J5_D5 43 PAR CBE1* CT_C8B J5_C5 44 GND GN D GND J5_B5 45 +3.3V AD14 GND J5 _A5 46 AD15 AD1 3 C T_D15 J5_E ...

  • Emerson 752I - page 87

    10006024-04 Katana ® 752i User’s Ma nual 10-1 Section 10 Ethernet Interfaces The Katana ® 752i supports four 10/100/1000B aseT Ethernet ports. The MV6446 0 system controller provides three Ethe rnet Media Access Control (MAC) uni ts, and an Intel 82544EI Ethernet controller device pr ovides direct access from the local PCI bus. Three Broadcom B ...

  • Emerson 752I - page 88

    Ethernet Interfaces: Ethernet Ports Katana ® 752i User’s Manual 10006024-0 4 10-2 001 = CPSB_1 (MA C address #2) 010 = CPSB_2 011 = FRN T_1 (ETH3) 100 = FRN T_2 (ETH4) 101 = reserved 110 = reserved 111 = reserved So for example, if the Katana ® 752i serial number is 1234, the CP SB_2 MAC address is: 00:80:F9:6 C:07:52. ETHERNET PORTS The MV6446 ...

  • Emerson 752I - page 89

    Ethernet Interfaces: Optional RMII PHY Devices 10006024-04 Katana ® 752i User’s Ma nual 10-3 Table 10-2: 82544EI Ethernet Port Pin Assignments, ETH4 Table 10-3: MV64460 Ethernet Port Pin Assignments, ETH3 OPTIONAL RMII PHY DEVICES In addition to the four GbE ports, th e Katana ® 752i supports an opti on for two RMII PHY devices on the Katana ® ...

  • Emerson 752I - page 90

    Ethernet Interfaces: Optional RMII PHY Devices Katana ® 752i User’s Manual 10006024-0 4 10-4 Figure 10-1: RMII PHY to Transition Mo dule PTMC Site 1 PTMC Site 2 J5 P13 P23 J5 Katana752i Optional Rear T ransition Module (i.e. TM/cSP AN-P8E) Magnetics Magnetics PHY 0x5 PHY 0x6 RMII RMII CR43 CR44 CR45 CR46 +2.5V +2.5V Backplane RJ45 RJ45 ...

  • Emerson 752I - page 91

    10006024-04 Katana ® 752i User’s Ma nual 11-1 Section 11 IPMI Controller The Katana ® 752i implements a System Management Bus ( SMB), as defined in the Com- pactPCI System Management Specificati on (see Table 1-2 ). It also supports the Intelligent Platform Management In terface (IPMI) Version 1. 5 and Intellig ent Platform Management Bus (IPMB ...

  • Emerson 752I - page 92

    IPMI Controller: SMB/IPMI Overview Katana ® 752i User’s Manual 10006024-0 4 11-2 The Katana ® 752i system management interfac e uses the Zircon PM devi ce’s general-pur- pose input/output (GPIO) pin s for the following functions: • watchdog sensor input (from 750GL processor) • GPIO (to 750GL p rocessor) • reset outputs (to 750GL proces ...

  • Emerson 752I - page 93

    IPMI Controller: SMB/IPMI Overview 10006024-04 Katana ® 752i User’s Ma nual 11-3 Figure 11-1: IPMB Connections Block Diagram IPMB (SCL, SDA, PWR) Katana752i 3 MV64460 IPMI Microcontroller IPMI Bootcode ROM IPMI Bootloader and FRU ROM Volt age Monitor Reset A-to-D 1 A-to-D 2 A-to-D 3 A-to-D 4 A-to-D 5 A-to-D 6 5 V 3.3 V 2.5 V 1.8 V (opt ional ) C ...

  • Emerson 752I - page 94

    IPMI Controller: I/O Interface Katana ® 752i User’s Manual 10006024-0 4 11-4 I/O INTERFACE The Zircon PM provid es 24 user-definable input/output (I/O) pins. The following table shows how the Katana ® 752i implements these pins. Table 11-1: Zircon PM General Purpose I/O Pin Functions Zircon PM Pin: Signal Name: Fun ction: GPIO0 TEMP1_OS unused ...

  • Emerson 752I - page 95

    IPMI Controller: I2C Interfaces 10006024-04 Katana ® 752i User’s Ma nual 11-5 In addition to the General Purpose I/O, th ere are six analog-to-digital (A2 D) input pins that are used for sensing th e variou s power supp lies on the board. The following table describes the Katana ® 752i implementat ion of these pins. Table 11-2: Zircon PM Analog ...

  • Emerson 752I - page 96

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-6 The PICMG 2.9 specification defines addressing on the public and private IPMBs . It defines the slave addresses assigned to the chassis, pow er supplies, and periphe ral boards based on geographical ad dressing. Table 11-3 lists the slave address of each per iph ...

  • Emerson 752I - page 97

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-7 The first byte contain s the responder’s Slave Address, rsSA . The second byte contains the Network Function Code, netFn , and the responder’s Logical Unit Number, rsLUN . The third byte contains the two’s-compl ement checksum fo r the first two bytes. The ...

  • Emerson 752I - page 98

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-8 IPMI Network Function Codes All IPMI messages contain a Network Function Co de field, which defi nes the category for a particular comma nd. Each category h as two co des assigned to it–one for requests and one for responses. The code for a request has the le ...

  • Emerson 752I - page 99

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-9 IPMI Completion Codes All IPMI response messages cont ain a hexadecimal Completion Code fi eld that indicates the status of the operation . Table 11-7 lists the Completion Codes (a s defined in the IPMI s pecifi- cation) used by the Zircon P M. Table 11-7: Compl ...

  • Emerson 752I - page 100

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-10 Zircon PM IPMI Commands The Zircon PM periphera l management control ler supports IPMI commands to query board information and to control th e behavior of the board. These commands p rovide a means to: • identify the controller • reset the controller • re ...

  • Emerson 752I - page 101

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-11 The Zircon PM implements ma ny standard IPMI commands. P lea se refer to the IPMI specifi- cation (l isted in Table 1 -2 ) for details about each command’s request and respons e data. The remainder of this section de scribes standard commands th at have Zirco ...

  • Emerson 752I - page 102

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-12 Table 11-9: Get Sensor Reading Parameters Type: Byte: Data Field: Request Data 1 Sensor Number (hex) 41=PMC 3.3V Voltage Monitor 42=CPU_CORE Voltage Monitor 43=1.8V Voltage Monitor 44=2.5V Voltage Monitor 45=3.3V Voltage Monitor 46=5.0V Voltage Monitor 50=750GL ...

  • Emerson 752I - page 103

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-13 Response Data (continued) 4 Present Threshold Co mparison Status For threshold-based sensors: Bits[7:6], R eserved. Re turned as 1 (binary). Ignore on re ad. Bit[5], 1= at or above ( ε ) upper non-recoverable threshold Bit[4], 1= at or above ( ε ) upper criti ...

  • Emerson 752I - page 104

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-14 Master Write-Read I 2 C (Application) The Master Write-Read I 2 C command allows for direct accesses to I 2 C devices. This com- mand can read from or write to any of the Zircon PM’s private I 2 C devices, such as SROMs or temperature sensors. Typically, you ...

  • Emerson 752I - page 105

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-15 Write Setting (OEM) The Write Setting command provides the ab ility to write a v alue to a general-pu rpose input/output (GPIO) pin on the Zi rcon PM. By to ggling certain GP IO pi ns, software can reset or power-down the board. Table 11- 11 shows the request/r ...

  • Emerson 752I - page 106

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-16 Read Setting (OEM) The Read Setting command pro vides the abilit y to read the value of a general-purpo se input/output (GPIO) pin o n the Zircon PM. Soft wa re can read certain GPIO pins to deter- mine if the board is in reset or powered-down. Table 11-12 show ...

  • Emerson 752I - page 107

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-17 Set Heartbeat (OEM) The Set Heartbeat command configures the Zircon PM to send a heartbeat message to a receiver on the IPMB or privat e I 2 C bus at a specific interval. T he interval can range between 100 milliseconds and 25 .6 seconds. The heart bea t messag ...

  • Emerson 752I - page 108

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-18 Get Heartbeat (OEM) The Get Heartbeat command return s the current configuration of the heartbeat func tion for a specified interface. The r esponse data has the same definition as the Set Hear tbeat request data (see Sectio n ). Table 11-14 shows the request/r ...

  • Emerson 752I - page 109

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-19 IPMI FRU In formation The Zircon P M stores Fie ld Replaceab le Unit (FRU) informati on in its boot memory ( SROM). The data structure co ntains information such as th e product name, part number, serial number, and manufacturing date. Pl ease refer to the IPMI ...

  • Emerson 752I - page 110

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-20 IPMI Device SDR Repository The Zircon PM implements a De vice SDR Repository that contains Sensor D ata Records for the Zircon PM, the FRU device, and each sensor. A system management cont roller may use the Get Device SDR command to read the rep ository and dy ...

  • Emerson 752I - page 111

    IPMI Controller: IPMI Message Protocol 10006024-04 Katana ® 752i User’s Ma nual 11-21 Event-generating sensors with a Threshold Event/Read ing Type (0x01 ) initiate an event message when a sensor reading crosses the define d threshold. The default thresholds for a particular sensor are retrieved by sending the Zircon PM a Get Sensor Thresholds c ...

  • Emerson 752I - page 112

    IPMI Controller: IPMI Message Protocol Katana ® 752i User’s Manual 10006024-0 4 11-22 The Event Dat a 0 byte has three fields: Bi ts 7:6 describe the cont ents of Event Data 1 (set t o 10 2 when an OEM code is present in Event Data 1). Bits 5:4 d escribe the content s of Event Data 2 (also set to 10 2 when an OEM code is present). Bi ts 3:0 stor ...

  • Emerson 752I - page 113

    10006024-04 Katana ® 752i User’s Ma nual 12-1 Section 12 Hot Swap The Katana ® 752i baseboard incorpora tes a Linear Tec hnologies LTC 1643L Hot Swap ™ con- troller device and is ful ly compliant with the CompactPCI (cPCI) Hot Swap Specification (se e references in Table 1-2 ). Katana ® 75 2i circuit boa rds allow for H igh Availabi lity Hot ...

  • Emerson 752I - page 114

    Hot Swap: cPCI Functionality Katana ® 752i User’s Manual 10006024-0 4 12-2 CPCI FUNCTIONALITY The Katana ® 752i implements an optiona l jumper, JP1 (s ee Fig. 2- 4 ), which can en able or dis- able the board’s cPCI funct ionality. By default, cPCI is enabled (jumpers placed on J P1, pins 1—2 and pins 7—8) . The jumper setti ngs also can p ...

  • Emerson 752I - page 115

    Hot Swap: Hot Swap LED and Ej ector Switch Control 10006024-04 Katana ® 752i User’s Ma nual 12-3 The Hot Swap logic funct ions as follows when a board is removed from a slot: 1 The operator opens the b oard’s ejector hand les and the PCI0_HS signals goes low to indicate th at the board is a bout to be ex tracted. 2 The REM bit is set, an d the ...

  • Emerson 752I - page 116

    Hot Swap: Hot Swap LED and Ej ector Switch Control Katana ® 752i User’s Manual 10006024-0 4 12-4 Non-cPCI Hot Swap When the cPCI funct ionality is disabled, the L ED/ejector switch cont rol mechanism works in conjunction wi th the Power Good indicati on fr om the Hot Swap contro ller circuit, as shown in Fig. 12-1 . Figure 12-1: Hot Swap Control ...

  • Emerson 752I - page 117

    Hot Swap: Timing Considerations 10006024-04 Katana ® 752i User’s Ma nual 12-5 low (active) . This occurs when powe r supply voltages are not within th e proper toleran ce or when the BDSEL* signal is not driven low (activ e) to the Hot Swap controll er. The LED remains illuminated until soft ware clears bit 0 at address F821,0006 16 in the HSL P ...

  • Emerson 752I - page 118

    Hot Swap: HEALTHY* Signal Katana ® 752i User’s Manual 10006024-0 4 12-6 HEALTHY* SIGNAL The Katana ® 752i logic asserts the HEAL THY* signal when ever the Hot Swa p controller indi - cates that all power sup plies provided by the ba ckplane are within the appropriate range. This signal passes through the Hot Swap Logi c (HSL) programma ble logi ...

  • Emerson 752I - page 119

    10006024-04 Katana ® 752i User’s Ma nual 13-1 Section 13 CT Bus Interface The Katana ® 752i supports an optional co mputer telephony ( CT) bus interface th at routes various signal s from the CompactPCI J4 backpl ane connector to the PCI T elecom Mezza- nine Card (PTMC) expansion sites. The Katana ® 752i complie s with Configu ration 2 of the ...

  • Emerson 752I - page 120

    CT Bus Interface: Katana®752i CT Bus Options Katana ® 752i User’s Manual 10006024-0 4 13-2 • User Managed Combination (UMC) UMC indicates combinations that are not to be made casu ally, since th ey may not be com- patible. Pot ential devic e destruction must be assumed for the se combinatio ns. For exam- ple, a PMC64 co mbined wit h a PT3CC i ...

  • Emerson 752I - page 121

    CT Bus Interface: Signal Control 10006024-04 Katana ® 752i User’s Ma nual 13-3 Figure 13-1: Typical System Clocking Model SIGNAL CONTROL The Katana ® 752i supports control signals that allow a PTMC site to master the CT clocks and/or data. The control registers are located in the Hot Swap Logic (HS L) programmable logic device (PLD) at hex a dd ...

  • Emerson 752I - page 122

    CT Bus Interface: CT Bus Routing Withou t the T8110 (option 1) Katana ® 752i User’s Manual 10006024-0 4 13-4 CT BUS ROUTING WITHOUT THE T8110 (OPTION 1) The Katana ® 752i option 1 routes the NETREF 1 and NETREF2 cloc k signals; as well as the FA, C8A, FB, and C8B data signal s between the J4 backplane con nector and the two PTMC site connectors ...

  • Emerson 752I - page 123

    CT Bus Interface: CT Bus Routing Withou t the T8110 (option 1) 10006024-04 Katana ® 752i User’s Ma nual 13-5 Figure 13-2: CT Signal Routing Diagram —T8110 Not Installed (option 1) PM/3Gv J23 P23 PM/3Gv T8105 J13 P13 NETREF2_ DIR CT_NET REF2 NETREF1_ DIR CT_NET REF1 J4/P4 NETREF1 NETREF2 C8_A C8_B FRAME_A FRAME_B C8_FRAME_A_D IR CT_C8A CT_C8B C ...

  • Emerson 752I - page 124

    CT Bus Interface: CT Bus Routing With th e T8110 Installed (option 2) Katana ® 752i User’s Manual 10006024-0 4 13-6 CT BUS ROUTING WITH THE T8110 INSTALLED (OPTION 2) The T8110 Ti me Slot Intercha nger (TSI) is a PCI device that se rves as a brid ge between th e H.110 and local CT bus on the Katana ® 752i. It must be properly configured befo re ...

  • Emerson 752I - page 125

    CT Bus Interface: CT Bus Routing With th e T8110 Installed (option 2) 10006024-04 Katana ® 752i User’s Ma nual 13-7 Local CT Bus Operation On the Katana ® 752i, option 2, the loca l CT clock mast er must always be the T8110. The two PTMC sites canno t be local CT bus masters (p rimary or secondary). They can only b e CT slaves. • PTMCx local ...

  • Emerson 752I - page 126

    CT Bus Interface: CT Bus Routing With th e T8110 Installed (option 2) Katana ® 752i User’s Manual 10006024-0 4 13-8 Figure 13-3: CT Signal Routing Diagram —T8110 Installed (option 2) H.110 CT Bus Operation For H.110 CT operation, the signa ls C8_FRAME_A_TERM an d C8_FRAME_B_T ERM in the HSL PLD (address F8 21,0003 16 , bits 2:3) must be cleare ...

  • Emerson 752I - page 127

    10006024-04 Katana ® 752i User’s Ma nual 14-1 Section 14 Backplane Signals This chapter describes the Katana ® 752i board’ s backplane signal s. It lists the pinouts for connecto rs J1, J2, J3, J4 , and J5 on th e CompactPC I backplane. OVERVIEW The Katana ® 752i backpla ne connectors provide the followin g connections: • Connector J1 carr ...

  • Emerson 752I - page 128

    Backplane Signals: Pinouts Katana ® 752i User’s Manual 10006024-0 4 14-2 PINOUTS J1 is a 110-pin female connector (Eme rson #01899062-00) that routes power su pply source signals from the Com pactPCI backpl ane, and cPCI and IPMI signals to t he CompactPCI backplane, as listed in th e following table. Table 14-1: cPCI Connector Pin Assignments, ...

  • Emerson 752I - page 129

    Backplane Signals: Pinouts 10006024-04 Katana ® 752i User’s Ma nual 14-3 J2 is a 110-pin female connect or (Emerson #0 1899063-00 ) that routes cPCI , Geographical Address, and power signals from the CompactPCI backpl ane, as listed in th e table below. Table 14-2: cPCI Connector Pin Assignments, J2 Pin: Row A: Row B: Row C: Ro w D: Row E: 22 GA ...

  • Emerson 752I - page 130

    Backplane Signals: Pinouts Katana ® 752i User’s Manual 10006024-0 4 14-4 J3 is a 95-pin female connec tor (Emerson #01899064-00) t hat routes cPSB Ethernet differ- ential signal s and PTMC site #1 user I/O si gnals to the cPCI ba ckplane, as li sted in the table below. Table 14-3: cPSB Connector Pin Assignments, J3 Pin: Row A: Row B: Row C: Row ...

  • Emerson 752I - page 131

    Backplane Signals: Pinouts 10006024-04 Katana ® 752i User’s Ma nual 14-5 J4 is an optional 90-pin fema le connector (Emerson #0189907 0-00) that routes CT signals between the PTMC sites and the cPCI backpl ane, as listed in the table below. Table 14-4: cPSB Connector Pin Assignments, J4 Pin: Row A: Row B: Row C: Row D: Row E: Row F: 25 SGA4 SGA3 ...

  • Emerson 752I - page 132

    Backplane Signals: Pinouts Katana ® 752i User’s Manual 10006024-0 4 14-6 J5 is a 110-pin femal e connect or (Emerson #0 1899063-00) t hat routes PTMC si te user I/O and Ethernet signals to th e cPCI backplane, as listed in the table below. Figure 14-1: cPCI Connector Pin Assignments, J5 Pin: Row A: Row B: Row C: Row D: Row E: 22 PMC1_ENET_TXP 3. ...

  • Emerson 752I - page 133

    10006024-04 Katana ®752i User’s Manual 15-1 Section 15 Monitor The Katana®752 i monitor is based on the Embedded P owerPC Linux Boot Proj ect ( PPC- Boot ) boot program, availabl e unde r the GNU General Public Lice nse (GPL). For instructions on how to obtain the source code for this GPL program, please visit http://www.emerson- embeddedcomput ...

  • Emerson 752I - page 134

    Monitor: Command-Line Features Katana ®752i User’s Manual 10006024-04 15-2 Figure 15-1: Example Monitor Start-up Disp lay PPCBoot 1.2.0 (Oct 31 2007 - 12:52:52)1.7s CPU: 750GX v1.2 @ 900 MHz Board: Katana752i BusHz: 200000000 I2C: ready DRAM: 512MB DDR SDRAM in slot 0 VM485L6523C-CC Early setup ECC (Clearing..) 512 MB Reserving 32MB for EDNR at ...

  • Emerson 752I - page 135

    Monitor: Basic Operation 10006024-04 Katana ®752i User’s Manual 15-3 BASIC OPERATION The Katana®752 i monitor performs various conf igurat ion tasks upon power-up or reset. This section describes the monito r operation during init ialization of the Kata na®752i board. The flowchart (see Fig. 15-2 ) illustrates the power-up an d reset sequence ...

  • Emerson 752I - page 136

    Monitor: Basic Operation Katana ®752i User’s Manual 10006024-04 15-4 Figure 15-2: Power-up/Reset Sequence Flowchart RESET Initialize HID0 Initialize M SR Relo cate the ba se of the MV6446 0 interna l regis ters 750GX floati ng point register initialization 750GX BAT an d segm ent regi ster initialization Invali dat e t h e cache LED 0001 Invalid ...

  • Emerson 752I - page 137

    Monitor: Basic Operation 10006024-04 Katana ®752i User’s Manual 15-5 Power-Up Timing Upon power-up, the Katan a®752i initiall y retries cPCI cycles for a spe cific period of time (see “cPCI/PCI Stop Retries, Memory Read Access Only” monitor state in the tables below). After that time, it stops retrying cycles on the cPCI bus. Caution: Any r ...

  • Emerson 752I - page 138

    Monitor: Basic Operation Katana ®752i User’s Manual 10006024-04 15-6 POST Diagnostic Results The Katana®752 i stores Power-On Self-T est (P OST) diagnost ic results in I 2 C nonvolatile random-access memory (NVRAM). This me mory is located in the EE PROM at hex address 0x53 on the I 2 C bus. The POST results are stored as a 32 -bit value at the ...

  • Emerson 752I - page 139

    Monitor: Monitor Recovery and Updates 10006024-04 Katana ®752i User’s Manual 15-7 MONITOR RECOVERY AND UPDATES Note: The monitor provides VxWorks 6 .0 support for Erro r Data and Reporting (EDNR). This feature allocates a per- sistent area of memory that retains its contents after a systerm soft reset. Any information stored in the 32- megabyte ...

  • Emerson 752I - page 140

    Monitor: Monitor Command Reference Katana ®752i User’s Manual 10006024-04 15-8 3 Update the monitor: [Katana 752i (1.0)] => moninit seria l# 100000 4 Reset the mo nitor: [Katana 752i (1.0)] => reset 5 Reset the en vironment para meters: [Katana 752i (1.0)] => envinit seria l# If moninit( ) fails, bu rn the new monitor to a ROM and fol l ...

  • Emerson 752I - page 141

    Monitor: Boot Commands 10006024-04 Katana ®752i User’s Manual 15-9 However, com mands cannot be abbreviate d when accessing on-line help. You must type help an d the full comman d name. Command Help Access the monitor online help for each command by t yping help < command > . The full command name must be entere d to access the online help ...

  • Emerson 752I - page 142

    Monitor: Boot Commands Katana ®752i User’s Manual 10006024-04 15-10 3 The host board finally write s 0x596F4F6B (charact er string “YoOk”) to MagicL oc to show that the appli cation is ready for the target. 4 The target writ es value 0x427965 21 (character stri ng “Bye!”) to Magi cLoc to show tha t the application was found. If necessary ...

  • Emerson 752I - page 143

    Monitor: Boot Commands 10006024-04 Katana ®752i User’s Manual 15-11 Definition: bootp [ loadAd dress ] [ bootfilename ] bootv The bootv command checks the c hecksum on the p rimary image (i n Flash) and b oots it, if valid. If it is not vali d, it checks the checksum on the secondary i mage (in Flash) and boots it, if valid. If nei ther checksum ...

  • Emerson 752I - page 144

    Monitor: JFFS2 File Systems Katana ®752i User’s Manual 10006024-04 15-12 JFFS2 FILE SYSTEMS This section describes the commands for th e read-only JFFS2 file systems. These com- mands assume a valid JFFS2 file system in Flash with support provided for two partitions: • Base of partition 0 i s 0xE8180000 • Base of part ition 1 is 0xE8000 000 ...

  • Emerson 752I - page 145

    Monitor: Memory Commands 10006024-04 Katana ®752i User’s Manual 15-13 cmp The cmp command co mpares count objects between addr1 and addr2 . Any differences are displayed o n the console display. Definition: cmp [.b, .w, .l] addr1 addr2 count cp The cp command copies count objects located at the source address to the target address. Note: If the ...

  • Emerson 752I - page 146

    Monitor: Memory Commands Katana ®752i User’s Manual 10006024-04 15-14 00080020: ffff ffff ffff ffff ffff ffff ffff ffff ... ............. 00080030: ffff ffff ffff ffff ffff ffff ffff ffff ... ............. mm The mm command modifies me mory one objec t at a time. Once started, the command line prompts for a n ew value at th e starting a ddress. ...

  • Emerson 752I - page 147

    Monitor: Flash Commands 10006024-04 Katana ®752i User’s Manual 15-15 00080020: ffffffff ffffffff ffffffff ff ffffff ................ 00080030: ffffffff ffffffff ffffffff ff ffffff ................ 00080040: ffffffff ffffffff ffffffff ff ffffff ................ 00080050: ffffffff ffffffff ffffffff ff ffffff ................ 00080060: ffffffff fff ...

  • Emerson 752I - page 148

    Monitor: EEPROM / I2C Commands Katana ®752i User’s Manual 10006024-04 15-16 protect The protect com mand enables or disables the Flash se ctor protection for the specified Flash sector. Protection is implemented using soft ware only. The protec tion mechanism inside the physical Flash part i s not being used. Definition: Protect all of the Flash ...

  • Emerson 752I - page 149

    Monitor: EEPROM / I2C Commands 10006024-04 Katana ®752i User’s Manual 15-17 icrc32 The icrc32 computes a CRC32 checksum. Definition: icrc32 chip _ a ddress [.0, .1, .2] count iloop The iloop command reads in an i nfinite loop on the specified address range. Definition: iloop chip_ad dress [.0, .1, .2] [# of objects] imd The imd command displa ys ...

  • Emerson 752I - page 150

    Monitor: Ethernet Controller EEPROM Commands Katana ®752i User’s Manual 10006024-04 15-18 iprobe The iprobe command probes to discover vali d I 2 C chip ad dresses. Definition: iprobe ETHERNET CONTROLLER EEPROM COMMANDS This section describes the comma nds that provide access to the EEPROM for the Intel 82544EI Ethernet Co ntroller. initeth4rom ...

  • Emerson 752I - page 151

    Monitor: Environment Parameter Commands 10006024-04 Katana ®752i User’s Manual 15-19 envinit The envinit command resets the NVRAM and serial number. Optional para meters allow you to: • specify t he processor num ber • specify the serial number • retrieve the serial number fro m the FRU device • specify parameters not in the default list ...

  • Emerson 752I - page 152

    Monitor: Test Commands Katana ®752i User’s Manual 10006024-04 15-20 TEST COMMANDS The commands describe d in this section perform diagnostic an d memory tests. diags The diags command runs th e power-on self test (POST) . Definition: diags mtest The mtest command perf orms a simp le SDRAM read/write test. Definition: mtest [ start [ end [ patter ...

  • Emerson 752I - page 153

    Monitor: Other Commands 10006024-04 Katana ®752i User’s Manual 15-21 coninfo The coninfo command displays the information for all av ailable console devices. Definition: coninfo crc16 The crc16 command computes a CRC16 checksum on size bytes starting at buff . Optionally, it stores the result at addr . Definition: crc16 address count crc32 The c ...

  • Emerson 752I - page 154

    Monitor: Other Commands Katana ®752i User’s Manual 10006024-04 15-22 frusetuser The frusetuser command writes count bytes to offset in the FRU user area and copies the bytes to storag e. Definition: frusetuser of fset count storage gethvr The gethvr command ret urns the contents of the Hard ware Version Register (see Regi ster Map 6-7 on page 6- ...

  • Emerson 752I - page 155

    Monitor: Other Commands 10006024-04 Katana ®752i User’s Manual 15-23 getpcimode The getpcimode command shows how many Configuration Spa ce Headers the Katana®752i is repo rting on PCI/ cPCI. Single Function means only Funct ion 0 is availabl e. Multi Function indicates that multipl e functions (i.e. Funct ion 0, Function 1, etc.) are available. ...

  • Emerson 752I - page 156

    Monitor: Other Commands Katana ®752i User’s Manual 10006024-04 15-24 isdram The isdram command displa ys the SDRAM configurat ion information ( valid chip value s range from 50 to 57). Definition: isdram loop The loop command executes an infinite loop on address range. Definition: loop [.b, .w, .l] address number_of_objects memmap The memmap com ...

  • Emerson 752I - page 157

    Monitor: Other Commands 10006024-04 Katana ®752i User’s Manual 15-25 Modify, read, and k eep the CFG address. pci next[.b, .w, .l] b.d.f address Modify automatically increment the CFG address. pci modify[.b, .w, .l] b.d.f address Write to the CFG address. pci write[.b, .w, .l] b.d.f address val ue reset The reset command performs a hard rese t o ...

  • Emerson 752I - page 158

    Monitor: Other Commands Katana ®752i User’s Manual 10006024-04 15-26 Setting PCI Mode to Multi ... Complete => setspr The setspr command sets the contents of the SP R register specified by SPR_ID to SDR_Value . Definition: setspr SPR_ID SPR_Value script The script command runs a list of moni tor commands out of memory. The list is an ASCII st ...

  • Emerson 752I - page 159

    Monitor: Environment Variables 10006024-04 Katana ®752i User’s Manual 15-27 version The version command displa ys the mo nito r’s current version number. Definition: version ENVIRONMENT VARIABLE S The following tabl e lists the monit or’s standard environment varia bles. Please note that holding down the s key during po werup forces the moni ...

  • Emerson 752I - page 160

    Monitor: Environment Variables Katana ®752i User’s Manual 10006024-04 15-28 cpci_remap 8000000 0 Base address in cPCI space for memory window specified by cpci_memsize (i.e. 0xC000,0000 from the Katana®752i maps to 0x8000,0000 in cPCI space) dcache on Initial data cache stat e Valid options: on, off ecc on ECC enable/disable (off = disable, on ...

  • Emerson 752I - page 161

    Monitor: Environment Variables 10006024-04 Katana ®752i User’s Manual 15-29 The monitor supports optional environment v ari ables that e nable addition al functionalit y. The moninit command ( see Section ) onl y affects the standard en vironment varia bles and does not set any parameters for these optio nal variables. Table 15-5: Optional Envir ...

  • Emerson 752I - page 162

    Monitor: Troubleshooting Katana ®752i User’s Manual 10006024-04 15-30 TROUBLESHOOTING To bypass the full board in itialization sequ ence, attach a terminal to the conso le located on the front of the module. Configu re the terminal parameters to be: 9600 bps, no parity, 8 data bits, 1 sto p bit Reset the module whil e holding down the ‘ s’ k ...

  • Emerson 752I - page 163

    10006024-04 Katana ®752i User’s Manual 16-1 Section 16 Acronyms ASCII American Standard C ode for Information Interchang e BMC Baseboard Management Controller Cmd Command code COP Common On Chip cPSB CompactPCI Packet-Switched Backpla ne CPU Central Processing Unit CRT Cathode Ray Tube CSA Canadian Standards A ssociation DAC Dual Access Cycles D ...

  • Emerson 752I - page 164

    Acronyms: Katana ®752i User’s Manual 10006024-04 16-2 IDMA Internal Direc t Memory Access IEC International Ele ctrotechnical Commission IEEE Institute of Electrical and Electronics Engineers IP Internet Protocol IPMB Intelligent Platfor m Management Bus IPMI Intelligent Platform Manag ement Interface ISP In-System Programmable ITP In-Target Pr ...

  • Emerson 752I - page 165

    Acronyms: 10006024-04 Katana ®752i User’s Manual 16-3 SERDES Serializer/Deserializer SGMII Serial Gigabit Media Ind ependent Interface SMS System Management Software SO-DIMM Small-Outline Dual In-line Memory SROM Serial Read Only Memory TAP Test Access Port TFTP Trivial Fil e Transfer Protocol UART Universal Asynchronous Receiver/transmitter UL ...

  • Emerson 752I - page 166

    Katana ®752i User’s Manual 10006024-04 16-4 (blank page ) ...

  • Emerson 752I - page 167

    10006024-04 Katana ® 752i User’s Manual i-1 Index A acronyms . . . . . . . . . . . . . . . . . . . 16-1 B binary download format . . . . . . .15-30 block diagram CPU . . . . . . . . . . . . . . . . . . . . . . . 4-2 CPU reset . . . . . . . . . . . . . . . . . . 3 -4 general system . . . . . . . . . . . . . . 1-4 IIC interface . . . . . . . . . . ...

  • Emerson 752I - page 168

    Index (continued) Katana ® 752i User’s Manual 10006024-04 i-2 memory commands . . . . . . . .15-12 Motorola S-record . . . . . . . . .15-30 other commands . . . . . . . . . .15-20 power-up/reset sequence flowchart 15-4 PPCBOOT . . . . . . . . . . . . . . . . . 15-1 recovery . . . . . . . . . . . . . . . . . . 15-7 start-up display . . . . . . . ...

  • Emerson 752I - page 169

    Index (continued) 10006024-04 Katana ® 752i User’s Manual i-3 S serial number location . . . . . . . . . . . . . . . . . . . . 2-7 user ROM . . . . . . . . . . . . . . . . . . 2-7 serial port, console . . . . . . . . . . . . 5-11 setup requirements . . . . . . . . . . . . 2-9 signals 66 MHz enable, PCI . . . . . . . . . . . 8 -3 ACK64*, PCI . . ...

  • Emerson 752I - page 170

    Katana ® 752i User’s Manual 10006024-04 i-4 (blank page ) ...

  • Emerson 752I - page 171

    10006024-04 Katana ®752i User’s Manual Notes ____________ __________ _____________ _____________ __________ ____________ ___________ ___________ ____________ __________ _____________ _____________ __________ ____________ ___________ ___________ ____________ __________ _____________ _____________ __________ ____________ ___________ ___________ __ ...

  • Emerson 752I - page 172

    Emerson Netwo rk Power, Embedded Co mputing 8310 Excelsior Drive ■ Madison, WI 53717-1935 USA US Toll Free: 1-800-356-9602 ■ Voice: +1-608-831-5500 ■ FAX: 1-608-831-4249 Email: info@ar tesyncp.com www.emersonembeddedcomputing.com Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service ...

Manufacturer Emerson Category Computer Hardware

Documents that we receive from a manufacturer of a Emerson 752I can be divided into several groups. They are, among others:
- Emerson technical drawings
- 752I manuals
- Emerson product data sheets
- information booklets
- or energy labels Emerson 752I
All of them are important, but the most important information from the point of view of use of the device are in the user manual Emerson 752I.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Emerson 752I, service manual, brief instructions and user manuals Emerson 752I. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Emerson 752I.

Similar manuals

A complete manual for the device Emerson 752I, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Emerson 752I by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Emerson 752I.

A complete Emerson manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Emerson 752I - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Emerson 752I, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Emerson 752I, that we can find in the current document
3. Tips how to use the basic functions of the device Emerson 752I - which should help us in our first steps of using Emerson 752I
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Emerson 752I
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Emerson 752I in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Emerson 752I?

Use the form below

If you did not solve your problem by using a manual Emerson 752I, ask a question using the form below. If a user had a similar problem with Emerson 752I it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)