Manual Mitsubishi Electronics FX3U-CF-ADP

124 pages 5.92 mb
Download

Go to site of 124

Summary
  • Mitsubishi Electronics FX3U-CF-ADP - page 1

    FX 3U -CF-ADP USER'S MANUAL ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 2

    ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 3

    (1) Before installation, operation, maintenance or inspection of this product, thoroughly read through and understand this manual and the associated manuals. Also, take care to handle the module properly and safely. This manual classifies the safety precautions into two categories: and . Depending on the circumstances, procedures indicat ed by may ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 4

    Safety Precautions (Read these precautions before using.) (2) 2. INSTALLATION PRECAUTIONS 3. WIRING PRECAUTIONS Reference • Make sure to sh ut down all pha ses of the power sup ply external ly before inst alling the FX 3U -CF-ADP. Failure to do so may ca use elec tric shock or damage t o the pro duct. 22 99 Reference • Use the product wit hin t ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 5

    Safety Precautions (Read these precautions before using.) (3) 4. STARTUP AND MAINTEN ANCE PRECAUTION S 5. DISPOSAL PRECAUTIONS 6. TRANSPORTATION PRECAUTIONS Reference • Make sure to co nn e ct the battery co rre c t ly . Do n ot c ha rg e, dis as s emb le , heat, shor t- cir cuit, or expo se the battery to fire. Doing so may rup ture or igni te i ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 6

    (4) ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 7

    1 FX 3U -CF-ADP User's Manual FX 3U -CF-ADP User's Manual Foreword This manual describes the FX 3U -CF-ADP CF card special adapter and should be read and understood before attempting to install the hardware. Store this manual in a safe place so that you can take it out and read it whenever necessary. Always forward it to the end user. © ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 8

    2 FX 3U -CF-ADP User's Manual Outline Precautions • This manual provides information for the use of the FX 3U -CF-ADP CF card special adapter. The manual has been written to be used by trained and competent personnel. The definition of such a person or persons is as follows; 1) Any engineer who is responsible for the planning, des ign and co ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 9

    3 FX 3U -CF-ADP User's Manual Table of Contents Table of Contents SAFETY PRECAUTIONS .................................................... ........................................... ... (1) Standards ................... ........... .............. ........... ........... .............. ............ .............. ........... . ............. 7 C ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 10

    4 FX 3U -CF-ADP User's Manual Table of Contents 5. Wiring 28 5.1 Which Power Supply Cable to Use ............................................................................................... 29 5.1.1 Power supply cable ........................ ......................... .............. ......................... .............. ............ .... ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 11

    5 FX 3U -CF-ADP User's Manual Table of Contents 8.7 FNC 304 - FLCMD / FX 3U -CF-ADP command ............................................................................. 74 8.7.1 Detailed explanation of setting data ..................... .............. .............. .............. .............. ....... .......... 75 8.8 FNC 305 - FLSTRD / FX ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 12

    6 FX 3U -CF-ADP User's Manual Table of Contents Appendix B: Version Information 113 Appendix B-1 Version information .................. ... .......... ................ ............. ................ ................ 11 3 Appendix B-1-1 Version check method ........... ........... .............. ....................... .............. .......... ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 13

    Standards 7 FX 3U -CF-ADP User's Manual Standards Certification of UL, cUL standards FX 3U -CF-ADP units comply with the UL standards (UL, cUL). UL, cUL File number :E95239 Regarding the standards that comply with the main unit, pl ease refer to either the FX series product catalog or consult with your nearest Mitsubishi product provider. Comp ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 14

    Standards 8 FX 3U -CF-ADP User's Manual Caution to conform with EC Directives • Installation in Enclosure Programmable logic controllers are open-type devices that must be installed and used within conductive control cabinets. Please use the programmable logic c ontroller while installed within a c onductive shielded control cabinet. Please ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 15

    Associated Manuals 9 FX 3U -CF-ADP User's Manual Associated Manuals Only the installation manual is packed together with the FX 3U -CF-ADP special adapter. For a detailed explanation of the FX 3U -CF-ADP special adapter, refer to this manual. For the hardware information and instructions on the PLC main unit, refer to the respective manuals. R ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 16

    Generic Names and A bbre viations Used in the Man ual 10 FX 3U -CF-ADP User's Manual Generic Names and Abbreviations Used in the Manual Generic name or abbre viat i on Description PLC FX 3U series Generic n ame for FX 3U Series PLC FX 3U PLC or ma in unit Generic nam e for FX 3U Series PLC main uni t FX 3UC series Generic name fo r FX 3UC Seri ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 17

    Generic Names and A bbre viations Used in the Man ual 11 FX 3U -CF-ADP User's Manual Generic name or abbre viat i on Description Manual FX 3U Hardware Editio n FX 3U Series Use r's Manual - Hardware Ed ition FX 3UC Hardware Ed iti on FX 3UC Series User's Man ua l - Hardware Edi tion Programming ma nual FX 3G /FX 3U /F X 3UC Seri es P ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 18

    Reading the Manua l 12 FX 3U -CF-ADP User's Manual Reading the Manual In this manual, the following formats are used for describing the common items. The above is different from the actual page, as it is provided for explanation only. This area shows the title of the chapter and the title of the section for the current page. The right side of ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 19

    1 Introduction 1.1 Outline 13 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 1. Introduction 1.1 Outline The CF card spe cial adapter FX 3U -CF-ADP (here inafter abbrevi ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 20

    1 Introduction 1.3 Power and status LEDs 14 FX 3U -CF-ADP User's Manual 1.3 Power and status LEDs LED display Color Status Descript ion POWER Green OFF Power is not b eing suppl ie d from the ex ternal power supply (24V DC). ON Power is bein g supplie d fr om the exte rnal power supp ly (24V DC). BUFFER Green OFF Data is not sto red in the i n ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 21

    2 Specificatio n 15 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2. Specification DESIGN PRECAUTIONS • Make sure to includ e the followi ng safety circuits o utside ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 22

    2 Specificatio n 2.1 General specificatio ns 16 FX 3U -CF-ADP User's Manual 2.1 General specifications For items not listed below, specifications are the same as the of the PLC main unit. For general specifications, refer to the manual of the PLC main unit. → Refer to the F X 3U Hardware Edition → Refer to the FX 3UC Hardware Edition *1. T ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 23

    2 Specificatio n 2.4 CF card AC CES S sw itch spe c if ic a t io n 17 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2.4 CF card ACCESS switch specification *1. Turn OFF ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 24

    3 System Configuration 3.1 General configurati on 18 FX 3U -CF-ADP User's Manual 3. System Configuration 3.1 General configuration Component list Part name Model name Remarks CF card special adap te r FX 3U -CF-ADP An expa nsion board is req uired to conne ct the CF-ADP with the FX 3U /FX 3UC -32MT- LT PLCs. PLC FX 3U /FX 3UC PLC - CompactFlas ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 25

    3 System Configuration 3.2 Applicable PLC 19 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 3.2 Applicable PLC 3.2.1 Connectable PLC The version number can be checked by ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 26

    3 System Configuration 3.4 Assignment o f channels 20 FX 3U -CF-ADP User's Manual 2. FX 3UC (D, DSS) PLC 3.4 Assignment of channels The CF-ADP is handled in the same way as communication expansion boards and communication special adapters for PLCs. Its channel number ("ch1" or "ch2") is assigned automatically in the order o ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 27

    3 System Configuration 3.4 Assignment o f channels 21 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2. FX 3UC (D, DSS) PLC • When using channel 1 (ch1) • When using ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 28

    4 Installation 22 FX 3U -CF-ADP User's Manual 4. Installation Only one CF-ADP unit can be connected to the left side of the main unit or special adapter. An expansion board is required to connect the CF-ADP with the FX 3U /FX 3UC -32MT-LT PLCs. For details, refer to the respective PLC manual. → Refer to the F X 3U Hardware Edition → Refer ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 29

    4 Installation 4.1 CF-ADP Co nn e c tio n 23 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.1 CF-ADP Connection An expansion board should be installed before connectio ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 30

    4 Installation 4.2 DIN rail mounting 24 FX 3U -CF-ADP User's Manual 4.2 DIN rail mounting The CF-ADP may be mounted on a 35mm (1.38") wide DIN46277 (DIN rail). Connect the CF-ADP to the PLC main unit before attaching the CF-ADP to a DIN rail. This sectio n explains an example where the CF-ADP is connected to a FX 3U PLC. Fo r the DIN rail ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 31

    4 Installation 4.3 Direct mounting 25 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.3 Direct mounting When the C F-ADP is conn ected to a FX 3U PLC, the CF-ADP m ay b ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 32

    4 Installation 4.4 Inserting an d Removal Procedures 26 FX 3U -CF-ADP User's Manual 4.4 Inserting and Removal Procedures 4.4.1 Inserting the CompactFl as h TM card The CompactFlash TM card can be inserted when the CF-ADP is power off. When the power supply of CF-ADP is ON and it inserts the CompactFlash TM card, make sure to perform of the fol ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 33

    4 Installation 4.4 Inserting an d Removal Procedures 27 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.4.2 Removing the Compac tFl as h TM card The CompactFlash TM car ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 34

    5 Wiring 28 FX 3U -CF-ADP User's Manual 5. Wiring DESIGN PRECAUTIONS • Make sure to includ e the followi ng safety circuits o utside the PLC to en sure safe sy stem operat ion even during exte rnal power supply problems or PLC failure. Otherwise, malfunctions may cause seriou s accidents. 1) A bove all, the f ollowing comp onents shoul d be ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 35

    5 Wiring 5.1 Which Power Supply Cable to Use 29 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 5.1 Which Power Supply Cable to Use The cable for connecting the CF-ADP po ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 36

    5 Wiring 5.2 Power Supply Wiring 30 FX 3U -CF-ADP User's Manual 5.2 Power Supply Wiring 5.2.1 Power supply wiring *1. The expansion board is required when connecting with the FX 3UC -32MT-LT PLC. Power-on/off timing The CF-ADP power supply should be turned ON simultaneously with or before the power supply of the PLC main unit. Before turning t ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 37

    5 Wiring 5.4 Power OFF procedure 31 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 5.4 Power OFF procedure Make sure to perform either of the following pr ocedures when ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 38

    5 Wiring 5.5 Connection o f the power supply cable 32 FX 3U -CF-ADP User's Manual 5.5 Connection of th e power supply cable The CF-ADP receives and supplies power through the built-in dedicated power connector. 5.5.1 Connection/removal of the power supply cable • Connection Connect the power supply cable after confirming the connector direct ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 39

    6 Function s 6.1 Details o f functions 33 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 6. Functions 6.1 Details of functions The user can perform the following pro ced ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 40

    6 Function s 6.2 Status informat ion 34 FX 3U -CF-ADP User's Manual 6.2 Status information The user can read the following status informat ion using applied instructions for the CF-ADP. • Detecting that a CompactFlash TM card is mounted. • Detecting that the CompactFlash TM card is full. • Detecting errors that have occurred in the CF-AD ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 41

    7 Before Programming 7.1 File format availa ble in the CF-ADP 35 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7. Before Programming This chapter describes several item ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 42

    7 Before Programming 7.1 File format availa ble in the CF-ADP 36 FX 3U -CF-ADP User's Manual Contents of files in the "csv" format 7.1.2 Files create d by the user The contents of files created by the user should be same as files created by the CF-ADP (refer to Subsection 7.1.1). For characters available in files, refer to Subsection ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 43

    7 Before Programming 7.1 File format availa ble in the CF-ADP 37 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.1.3 Characters availa ble in files Following characters ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 44

    7 Before Programming 7.1 File format availa ble in the CF-ADP 38 FX 3U -CF-ADP User's Manual 7.1.4 Data size calculation When calculating the data size, use the following fo rmula in accordance with the byte count shown in the table below. Calculation formula for the byte count that can be wr itten at one time Number of data points : n (n 254) ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 45

    7 Before Programming 7.1 File format availa ble in the CF-ADP 39 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.1.5 Data writing destination Data can be written to two ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 46

    7 Before Programming 7.1 File format availa ble in the CF-ADP 40 FX 3U -CF-ADP User's Manual 7.1.6 File ID Applied instructions for the CF-ADP use the file ID for specifying files. Accordingly, the file name saved in the CompactFlash TM card is associated with the file ID, and controlled by the ID table. When a file whose file ID is "1&qu ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 47

    7 Before Programming 7.1 File format availa ble in the CF-ADP 41 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.1.7 FIFO file When the file ID is set to "K0" ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 48

    7 Before Programming 7.2 Directory structure 42 FX 3U -CF-ADP User's Manual 7.2 Directory structure The following directory is created inside the CompactFlash TM card. • In the case of a normal file The directory "FX3U_CFDATA." is created inside the CompactFlash TM card. The following data is stored in the directory. • In the ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 49

    7 Before Programming 7.4 General Rules for Applied Instruct ions 43 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.4 General Rules for Applied Instructions 7.4.1 Expre ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 50

    7 Before Programming 7.4 General Rules for Applied Instruct ions 44 FX 3U -CF-ADP User's Manual 7.4.2 Programming using "Ins truction execution complete " flag and "Instruction execution abnormal end" flag 1) If two or more CF-ADP instructions are used in a program, the "Instruction execution complete" flag (M8029 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 51

    7 Before Programming 7.4 General Rules for Applied Instruct ions 45 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2) To use at a position oth er than just below the CF- ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 52

    8 CF-ADP Applied Instruc tions Explanatio n 8.1 CF-ADP Instructions types 46 FX 3U -CF-ADP User's Manual 8. CF-ADP Applied Instructions Explanation This chapter explains applied instructions for the CF-ADP. 8.1 CF-ADP Instructions types The PLC and the CF-ADP transfer data to each other using applied instructions for the CF-ADP. Six applied in ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 53

    8 CF-ADP Applied Instruc tions Explanatio n 8.2 Common Items in CF -ADP Instruction s 47 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4. Operation when an error occurr ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 54

    8 CF-ADP Applied Instruc tions Explanatio n 8.3 FNC 300 - FLCRT / File create•check 48 FX 3U -CF-ADP User's Manual 8.3 FNC 300 - FLCRT / File create•check Outline The FLCRT instruction creates a file inside the Compa ctFlash TM card mounted in the FX 3U -CF-ADP. When executed after c reation of a new file, the FL CRT instruction chec ks th ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 55

    8 CF-ADP Applied Instruc tions Explanatio n 8.3 FNC 300 - FLCRT / File create•check 49 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.3.1 Detailed explanation of set ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 56

    8 CF-ADP Applied Instruc tions Explanatio n 8.3 FNC 300 - FLCRT / File create•check 50 FX 3U -CF-ADP User's Manual Caution When the file ID is "K0" 1) The CF-ADP can create up to 1000 files (within the CompactFlash TM card capacity). 2) The file name is set to "FILE0000.CSV" to "FILE0999.CSV". When the file ID i ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 57

    8 CF-ADP Applied Instruc tions Explanatio n 8.4 FNC 301 - FLDEL / File delete•CF card format 51 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.4 FNC 301 - FLDEL / Fi ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 58

    8 CF-ADP Applied Instruc tions Explanatio n 8.4 FNC 301 - FLDEL / File delete•CF card format 52 FX 3U -CF-ADP User's Manual 8.4.1 Detailed explanation of setting data Details of the setting data in the FLDEL instruction are as shown below. Cautions When the file ID "K0 (FIFO file)" or "K-1 (all files)" is spec if ied, it ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 59

    8 CF-ADP Applied Instruc tions Explanatio n 8.4 FNC 301 - FLDEL / File delete•CF card format 53 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 3) Program Example 3 Thi ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 60

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 54 FX 3U -CF-ADP User's Manual 8.5 FNC 302 - FLWR / Data write Outline The FLWR instruction writes data to the CompactFlash TM card or to the buffer inside the FX 3U -CF-ADP. 1. Instruction format 2. Set data 3. Appl icable devices Explanation of function and operation ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 61

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 55 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting The FLWR instruction writ es data s pec ifi ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 62

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 56 FX 3U -CF-ADP User's Manual 8.5.1 Detailed explanation of setting data Details of the setting data in the FLWR instruction are as shown below. Cautions 1) The FLWR instruction is completed abnormally if a CompactFlash TM card is not mounted. 2) The user should pay c ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 63

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 57 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.5.2 Writing data of same type "m&quo ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 64

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 58 FX 3U -CF-ADP User's Manual • Sequence program It is assumed that D10 to D14 store values. This program does not describe such values. Specify the line position of the writing destination. Additional writing is specified. D22 K1 D23 K5 FNC 12 MOV Specify the data ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 65

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 59 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2. When overwriting data in a previously wr ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 66

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 60 FX 3U -CF-ADP User's Manual • Sequence program It is assumed that D10 and D11 store values. This program does not describe such values. Specify the line position of the writing destination. Index 2 is specified as the target of overwriting. D22 K3 D23 K2 FNC 12 MO ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 67

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 61 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.5.3 Writing data of different types Data ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 68

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 62 FX 3U -CF-ADP User's Manual 1. When writing additi ona l data to a file • Set the data writing parameters as follows in all of a series of FLWR instructions. - Line position of writing destination : K-1 (Additional writing) - Column position : K-1 • A series of ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 69

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 63 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting • Sequence program It is assumed that D10 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 70

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 64 FX 3U -CF-ADP User's Manual D200 D8438 D201 D8437 FNC 12 MOV The error code is stored. The error code details are stored. FNC 12 MOV M0 RST M0 RST M8029 M8329 Specify the line position of the writing destination. Additional writing is specified. D62 K-1 D63 K1 FNC 1 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 71

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 65 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2. When overwriting data in a previously wr ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 72

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 66 FX 3U -CF-ADP User's Manual • Sequence program It is assumed that M15 stores bit data, M16 stores bit data, and R200 stores 16-bit decimal data. This program does not describe such values. Specify the line position of the writing destination. The overwriting targe ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 73

    8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 67 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting D100 D8438 D101 D8437 FNC 12 MOV The error ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 74

    8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 68 FX 3U -CF-ADP User's Manual 8.6 FNC 303 - FLRD / Data read Outline The FLRD instruction reads data from the CompactFlash TM card. 1. Instruction format 2. Set data 3. Appl icable devices Explanation of function and operation 1. 16-bit operation (FLRD) The FLRD instru ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 75

    8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 69 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.6.1 Detailed explanation of setting data D ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 76

    8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 70 FX 3U -CF-ADP User's Manual 8.6.2 Reading data of the same type from a file "m" data points of the same data type in one line are read as follows. Program Exa mple • Explanation of operation When X000 turns ON, two decimal (16-bit) data points are read fr ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 77

    8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 71 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.6.3 Reading data of diff erent types from ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 78

    8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 72 FX 3U -CF-ADP User's Manual Program Exa mple • Explanation of operation When X000 turns ON, 4 data points of different types are r ead from the 1st column in Index 2 in the following file. Each device shown below stores the read data, an d D10 stores the total numb ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 79

    8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 73 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting D300 D8438 D301 D8437 FNC 12 MOV The error c ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 80

    8 CF-ADP Applied Instruc tions Explanatio n 8.7 FNC 304 - FLCMD / FX3U-CF-ADP command 74 FX 3U -CF-ADP User's Manual 8.7 FNC 304 - FLCMD / FX 3U -CF-ADP command Outline The FLCMD instruction gives instruction for operation to the FX 3U -CF-AD P. 1. Instruction format 2. Set data 3. Appl icable devices Explanation of function and operation 1. 1 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 81

    8 CF-ADP Applied Instruc tions Explanatio n 8.7 FNC 304 - FLCMD / FX3U-CF-ADP command 75 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.7.1 Detailed explanation of set ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 82

    8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 76 FX 3U -CF-ADP User's Manual 8.8 FNC 305 - FLSTRD / FX 3U -CF-ADP status read Outline The FLSTRD instruction reads the status (including t he error information and file information) of the FX 3U -CF- ADP. 1. Instruction format 2. Set data 3. Appl icabl ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 83

    8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 77 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.8.1 Detailed explanation o ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 84

    8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 78 FX 3U -CF-ADP User's Manual • When is "K768 (H300)" The FLSTRD instruction reads the version information of the CF-ADP. • When is "K1024 (H400)" The FLSTRD instruction reads the error information (error flag). • When is " ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 85

    8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 79 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2) Program Example 2 When X0 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 86

    8 CF-ADP Applied Instruc tions Explanatio n 8.9 Contents of Related De vices 80 FX 3U -CF-ADP User's Manual 8.9 Contents of Related Devices The tables below show special auxiliary relays and special data registers used in CF-ADP instructions (FNC300 (FLCRT) to FNC305 (FLSTRD)). For details on the related devices, refer to Appendix A-2. 1. S pe ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 87

    9 Program Examples 9.1 System Configurati on 81 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9. Program Examples 9.1 System Configuration The system configuration show ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 88

    9 Program Examples 9.2 Program Example 1 82 FX 3U -CF-ADP User's Manual 9.2 Program Example 1 9.2.1 Operation details • When X000 turns ON, the following file is created. If a file whose file ID is "1" already exists in the CompactFlash TM card, file creation and data name writing are aborted. - File ID = 1 - File name = DWORD_01 - ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 89

    9 Program Examples 9.2 Program Example 1 83 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.2.3 Device Assi gnments Device No. Contents o f operatio n X000 Creates a 32 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 90

    9 Program Examples 9.2 Program Example 1 84 FX 3U -CF-ADP User's Manual 9.2.4 Sequence Program This program example describes the sequence program for channel 1 (ch1). Rewrite the channel No. with the actual system configuration to be used. → For explanation of operations, refer to Subsection 9.2.1. → For an example of a 32-bit decimal typ ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 91

    9 Program Examples 9.2 Program Example 1 85 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting *1. When is "K7" or "K8", 00H, which indicates the end of ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 92

    9 Program Examples 9.2 Program Example 1 86 FX 3U -CF-ADP User's Manual Specify the data writing type. D21 K1 D22 K1 FNC 12 MOV Specify the line position of the writing destination. Number of written data points. Writing destination. Specify the data column position in the writing destination. FNC 12 MOV D20 K8 FNC 12 MOV D23 K10 FNC 12 MOV D1 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 93

    9 Program Examples 9.2 Program Example 1 87 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting The buffered data forcible writing execution counter is set to "0". ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 94

    9 Program Examples 9.2 Program Example 1 88 FX 3U -CF-ADP User's Manual File delete. M8405 CF card is mounted M3 M8404 CF-ADP unit ready Remains ON while the 32- bit decimal type file is being deleted Remains ON while the 32-bit decimal type file is being deleted. D112 D8418 D113 D8417 FNC 12 MOV The error code is stored. Remains ON while the ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 95

    9 Program Examples 9.3 Program Example 2 89 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.3 Program Example 2 9.3.1 Operation details • When X004 turns ON, the foll ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 96

    9 Program Examples 9.3 Program Example 2 90 FX 3U -CF-ADP User's Manual X007 Deletes the mixed type f ile. M4 Remains O N whil e a mixed type file is be in g cr eated. M5 Remains ON while data is b eing written to the mixed typ e file. M6 Remains ON while data is being read from the mixed ty pe file. M7 Remains O N whil e the mixed type file i ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 97

    9 Program Examples 9.3 Program Example 2 91 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.3.4 Sequence Program This program example describes the sequence program for ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 98

    9 Program Examples 9.3 Program Example 2 92 FX 3U -CF-ADP User's Manual *1. When is "K7" or "K8", 00H, which indicates the end of the string, must be added to the end of the character string. In addition, in sequence example, it is written in such a way that "00H" is placed in a blank area of a characte r string. ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 99

    9 Program Examples 9.3 Program Example 2 93 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting Specify the line position of the writing destination. D22 K1 D23 K7 FNC 12 MOV ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 100

    9 Program Examples 9.3 Program Example 2 94 FX 3U -CF-ADP User's Manual From previous page From previous page To next page To next page Number of written data points. Data writing. Specify the data writing type. D23 K1 FNC 12 MOV FNC302 FLWR K0 D20 K2 FNC 12 MOV R0 D20 D30 K1 Number of written data points. Data writing. Specify the data writin ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 101

    9 Program Examples 9.3 Program Example 2 95 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting Specify the line position from which data is read.(Final line) D42 K1 D43 K7 F ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 102

    9 Program Examples 9.3 Program Example 2 96 FX 3U -CF-ADP User's Manual Specify the data reading type. D40 K6 FNC 12 MOV D43 K1 FNC 12 MOV Number of read data points. Data reading. FNC303 FLRD K0 D40 R140 D50 K1 Specify the data reading type. D40 K7 FNC 12 MOV D43 K1 FNC 12 MOV Number of read data points. Data reading. FNC303 FLRD K0 D40 R150 ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 103

    9 Program Examples 9.4 Program Example 3 97 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.4 Program Example 3 9.4.1 Operation details When X010 turns ON, error codes, ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 104

    9 Program Examples 9.4 Program Example 3 98 FX 3U -CF-ADP User's Manual 9.4.3 Sequence Program This program example describes the sequence program for channel 1 (ch1). Rewrite the channel No. with the actual system configuration to be used. → For explanation of operations, refer to Subsection 9.4.1. → For device assignments, refer to Subse ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 105

    10 Troubl e shooting 99 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 10. Troubleshooting INSTALLATION PRECAUTIONS • Make sure to sh ut down all pha ses of the power ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 106

    10 Troubl e shooting 100 FX 3U -CF-ADP User's Manual STARTUP AND MAINTEN ANCE PRECAUTIONS • Make sure to connect the batter y correctly. Do not ch arge, disa ssemble, hea t, short-cir cuit, or expose the battery to f ire. Doing so may rup ture or igni te it. • Do not touch an y terminal whi le the PLC's p owe r is on. Doing so may cau ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 107

    10 Troubl e shooting 10.1 Troubleshooti ng procedure 101 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 10.1 Troubleshooting procedure 10.1.1 LED status chec k The table ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 108

    10 Troubl e shooting 10.1 Troubleshooti ng procedure 102 FX 3U -CF-ADP User's Manual 10.1.3 Error Code List and Action The list below shows error codes and corrective actions. 1. Error code list Error code Error definit io n Error correcti ve action 1 Parity, Fram ing, Overrun error Check the con nection to the CF- ADP. 2 Communicatio n charac ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 109

    10 Troubl e shooting 10.1 Troubleshooti ng procedure 103 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 37 Outside devi ce point number range in mix ed type specifica ti ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 110

    10 Troubl e shooting 10.1 Troubleshooti ng procedure 104 FX 3U -CF-ADP User's Manual 503 ID table read error The file management in formation was not able to be read from the CompactFlash TM card. When readin g or deletin g a file, co nfirm that the target f ile exists. 504 ID table corr upt ion error The file mana gement infor mation is cor r ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 111

    10 Troubl e shooting 10.1 Troubleshooti ng procedure 105 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 805 Outside dat a line p osition r ange Data cannot be writ ten t ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 112

    10 Troubl e shooting 10.1 Troubleshooti ng procedure 106 FX 3U -CF-ADP User's Manual 909 Buffered data writing error to CompactFl ash TM card Buffered d ata was not abl e to be written to the Compa ctFlash TM card. Check whethe r the CompactFla sh TM card is mounted correctly , and whether it has sufficient f ree space. In the cas e of FIFO fi ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 113

    10 Troubl e shooting 10.2 Diagnostics o n the PLC Main Unit 107 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 10.2 Diagnostics on the PLC Main Unit The following descri ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 114

    10 Troubl e shooting 10.2 Diagnostics o n the PLC Main Unit 108 FX 3U -CF-ADP User's Manual 10.2.3 ERROR(ERR) LED [on/flashing/off] The table below describes details for the LED statuses. Status PLC Stat us Error correc tive action ON A watchdog time r error may ha ve occurred, or the hard ware of the PLC may b e damaged. 1) Stop the PLC, and ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 115

    Appendix A: Relate d Devices Appendix A-1 Related Devic e List 109 FX 3U -CF-ADP User's Manual A Relat ed Dev ices B V ersion Information Appendix A: Related Devices Appendix A-1 Related Device List The tables below show special auxiliary relays and special data registers used in CF-ADP instructions (FNC300 (FLCRT) to FNC305 (FLSTRD)). 1. S pe ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 116

    Appendix A: Relate d Devices Appendix A-2 Details of related devices 110 FX 3U -CF-ADP User's Manual Appendix A-2 Details of related devices This section explains devices used during CF-ADP. Appendix A-2-1 Instruction ex ecution complete [M8029] When execution of CF-ADP instructions is completed, this device turns ON. 1. Detailed contents When ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 117

    Appendix A: Relate d Devices Appendix A-2 Details of related devices 111 FX 3U -CF-ADP User's Manual A Relat ed Dev ices B V ersion Information Appendix A-2-5 CF card mount status [M8405, M8425] These devices indicate the CompactFlash TM card status. 1. Detailed contents When the CompactFlash TM card is mounted, one of these devices turns ON. ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 118

    Appendix A: Relate d Devices Appendix A-2 Details of related devices 112 FX 3U -CF-ADP User's Manual Appendix A-2-10 Step number of an instruction for the CF-ADP where an error has occurred [D8415, D8414] [D8435, D8434] These devices store the step number of an instruction for the CF-ADP where an error has occurred. 1. Detailed contents These ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 119

    Appendix B: V ersi on Info rmation Appendix B-1 Version information 113 FX 3U -CF-ADP User's Manual A Relat ed Dev ices B V ersion Information Appendix B: Version Information Appendix B-1 Version information Appendix B-1-1 Version check method 1. Checking the nameplate The CF-ADP version is indicated by "SERIAL" on the label attached ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 120

    Appendix B: V ersi on Info rmation Appendix B-1 Version information 114 FX 3U -CF-ADP User's Manual MEMO ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 121

    115 FX 3U -CF-ADP User's Manual Warranty Warranty Please confirm the following product warra nty details before using this product. 1. Gratis Warranty Term and Gratis Warran ty Range If any faults or defects (he reinafter "Failure") found to be the responsibility of M itsubis hi occurs during use of the product within th e gratis war ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 122

    116 FX 3U -CF-ADP User's Manual Revised History Revised History Date Revision Desc ription 6/2009 A First Edition ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 123

    ...

  • Mitsubishi Electronics FX3U-CF-ADP - page 124

    HEAD OFFICE: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN HIMEJI WORKS: 840, CHIYO DA CHO, HIMEJI, JAPAN JY997D35401A (MEE) Effective June 2009 Specifications are subject to chang e withou t notice. FX 3U -CF-ADP USER'S MANUAL MODEL FX3U-CF-ADP-U-E MODEL CODE 09R720 ...

Manufacturer Mitsubishi Electronics Category Video Gaming Accessories

Documents that we receive from a manufacturer of a Mitsubishi Electronics FX3U-CF-ADP can be divided into several groups. They are, among others:
- Mitsubishi Electronics technical drawings
- FX3U-CF-ADP manuals
- Mitsubishi Electronics product data sheets
- information booklets
- or energy labels Mitsubishi Electronics FX3U-CF-ADP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Mitsubishi Electronics FX3U-CF-ADP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Mitsubishi Electronics FX3U-CF-ADP, service manual, brief instructions and user manuals Mitsubishi Electronics FX3U-CF-ADP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Mitsubishi Electronics FX3U-CF-ADP.

A complete manual for the device Mitsubishi Electronics FX3U-CF-ADP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Mitsubishi Electronics FX3U-CF-ADP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Mitsubishi Electronics FX3U-CF-ADP.

A complete Mitsubishi Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Mitsubishi Electronics FX3U-CF-ADP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Mitsubishi Electronics FX3U-CF-ADP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Mitsubishi Electronics FX3U-CF-ADP, that we can find in the current document
3. Tips how to use the basic functions of the device Mitsubishi Electronics FX3U-CF-ADP - which should help us in our first steps of using Mitsubishi Electronics FX3U-CF-ADP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Mitsubishi Electronics FX3U-CF-ADP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Mitsubishi Electronics FX3U-CF-ADP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Mitsubishi Electronics FX3U-CF-ADP?

Use the form below

If you did not solve your problem by using a manual Mitsubishi Electronics FX3U-CF-ADP, ask a question using the form below. If a user had a similar problem with Mitsubishi Electronics FX3U-CF-ADP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)