Manual Barco CTHD-61B

68 pages Not applicable
Download

Go to site of 68

Summary
  • Barco CTHD-61B - page 1

    an intr oducon to the project or an intr oducon to the project or CT series User Manual www.barco.com ...

  • Barco CTHD-61B - page 2

    english 2 User’ s Guide – Getting to know the projector CT series User Manual ...

  • Barco CTHD-61B - page 3

    english 3 Contents 1 Introduction 7 1.1 Thank you 1.2 T raining 1.3 Symbols used in this documentation 2 Safety and compliance 9 2.1 General safety considerations 2.2 Information/W arning - Potential Mercury V apour Health Issues 2.3 FCC compliance 2.4 Disposal information 2.4.1 Statement WEEE (W aste Electrical and Electronic Equipment) 2.4.2 Disp ...

  • Barco CTHD-61B - page 4

    4 User Manual - Introduction english 5 Overview 25 5.1 Keypad and indicator 5.2 Wireless remote contr ol 5.3 Connectors 5.3.1 Signal connectors 5.3.2 Control connectors 5.4 Menu system 5.4.1 T op menu 5.5 3D main menu 5.5.1 3D > Dual head setup sub menu 5.6 Picture main menu 5.6.1 Picture > RealColor sub menu 5.6.2 Picture > Advanced sub m ...

  • Barco CTHD-61B - page 5

    english 5 6.10 PIN code 6.11 Disabling the wireless r emote contr ol (IR) receivers 6.12 Software upgrades 7 Optimising the image 55 7.1 Calibration data 7.1.1 Updating RealColor™ calibration data 7.1.2 RealColor™ modes 7.2 Setting a white point or color temperature 7.2.1 Defining the system color gamut 7.3 Gamma 8 T echnical specifications 6 ...

  • Barco CTHD-61B - page 6

    6 User Manual - Introduction english CT series User Manual - Introduction ...

  • Barco CTHD-61B - page 7

    english 7 1 Introduction 1.1 Thank you Thank you for purchasing this pr ojector . When referring to the term CT series in this document the content is applicable for the following Barco pr oducts: • CTHD-61B (1920x1080) • CTWU-61B (1920x1200) • CTWQ-51B (2560x1600) • CTPN-41B (2560x1080) The CT series projectors set an industry benchmark fo ...

  • Barco CTHD-61B - page 8

    8 User Manual - Introduction english CT series User Manual - Introduction ...

  • Barco CTHD-61B - page 9

    english 9 2 Safety and compliance 2.1 General safety considerations • Use only the cables and cords supplied with the pr ojector or original replacement cables. Using other cables or cords may lead to malfunction and permanent damage to the unit. • Always use 3-prong (gr ounded) power cord to ensur e pr oper grounding of the unit. Never use 2-p ...

  • Barco CTHD-61B - page 10

    10 User Manual - Intr oduction english 2.2 Information/W ar ning - Potential Mer cury V apour Health Issues This projector uses a very powerful UHP™ lamp for illumination to pr oduce an extremely bright image. This technology is similar to other high-pressur e discharge lamps that are extensively used in cars, street lights and other lighting app ...

  • Barco CTHD-61B - page 11

    english 11 2.4 Disposal information 2.4.1 Statement WEEE (W aste Electrical and Electronic Equipment) This symbol on the product indicates that, under the Eur opean Directive 2012/19/EU govern - ing waste from electrical and electr onic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipmen ...

  • Barco CTHD-61B - page 12

    12 User Manual - Intr oduction english CT series User Manual - Safety and compliance ...

  • Barco CTHD-61B - page 13

    english 13 3 What is in the box? The following components are standard delivery: Projector Power Cable (Country Dependent) Remote Control User Documentation Additional accessories available for the projector: Exhaust air kit (for ceiling mount) : A: Air -inlet filter (also sold separately) B: Side cover/Air -inlet C: Ceiling mount cover/Air -outle ...

  • Barco CTHD-61B - page 14

    14 User Manual - Intr oduction english CT series User Manual - What’ s in the box? ...

  • Barco CTHD-61B - page 15

    english 15 4 Installation 4.1 System considerations Please refer to Chapter 5 Overview for an explanation on the various featur es of the projector . Installation should only be performed by trained and skilled personnel in order to achieve the desired r esults. Safety first: Projectors and other equipment that ar e not mounted properly r epr esen ...

  • Barco CTHD-61B - page 16

    16 User Manual - Intr oduction english 4.2 V entilation Minimum safety distance to any side of the unit is 50cm / 20” in any direction. Hot air is exhausted from the r ear vent. Do not place objects that are sensitive to heat closer than 50cm / 20” to the exhaust vent. Figure 4-1. Positioning the projector When the projector is ceiling mounted ...

  • Barco CTHD-61B - page 17

    english 17 4.3 Ceiling and rig mounting Use the three mounting holes pr ovided in the bottom part to securely fix the pr ojector to a ceiling or rig mount. Use M6 screws that pr otrude maximum 9mm into the projector body . Figure 4-2. Ceiling/rig mounting mounting holes 4.4 Locking the pr ojector The projector can be locked physically by using a s ...

  • Barco CTHD-61B - page 18

    18 User Manual - Intr oduction english 4.6 Selecting a lens The projector is deliver ed without a lens, enabling you to select a lens according to your desired image size and pr ojection distance. The projector uses a bayonet mount system to precisely fix the lens in place. The lenses ar e manual, meaning zoom, focus and iris adjust - ments are do ...

  • Barco CTHD-61B - page 19

    english 19 4.6.1 Inserting a lens 1. Remove the protection lid on the pr ojector by turning the lid anti-clockwise until it comes loose 2. Remove the protection lids fr om the lens 3. Insert the lens, making sure the r ed line marking on the lens points straight up towards the top of the cabinet. If the lens does not enter on the first attempt, re ...

  • Barco CTHD-61B - page 20

    20 User Manual - Intr oduction english 4.7 Lens lock A lens-lock feature is available wher eby three scr ews on the lens barr el are used to perma - nently fix the zoom, focus and iris positions. For information on locking the adjustment rings in one position, please refer to section 3.10 Zoom, focus and iris. Figure 4-6. Zoom and Focus Lens lock ...

  • Barco CTHD-61B - page 21

    english 21 4.9 Lens planarity (Scheimpflug adjustment) This adjustment is rarely needed, do not apply it unless it is r equired. Certain applications requir e fine adjustment of the lens planarity in order to obtain an image that is focused. The projector is fitted with thr ee adjustment screws (Allen key 3mm/5mm) around the bayonet mount that f ...

  • Barco CTHD-61B - page 22

    22 User Manual - Intr oduction english 4.11 Making the connections The projector is equipped with multiple signal and contr ol interfaces to support various video and data sources (see connector panel below), as well as dif ferent contr ol systems. Always make sure that the pr ojector is powered of f befor e connecting any signal and/ or control ca ...

  • Barco CTHD-61B - page 23

    english 23 4.15 Image sizes Lens types and specifications may change without prior notice. For correct lens information please r efer to www .barco.com 1920 x 1200/1920 x1080 (WUXGA/1080) Ultra Wide Fixed (EN53) 0.74 : 1 (0.8 - 3.3m) Wide Angle (EN52) 0.92 : 1 (1.0 - 10m) Long Throw Zoom (EN54) 2.68 - 4.18 : 1 (5 – 25m) Projection distance Image ...

  • Barco CTHD-61B - page 24

    24 User Manual - Intr oduction english 2560 x 1600/ 2560x1080 (WQXGA/Panorama) Lens types and specifications may change without prior notice. For correct lens information and other r esolutions please refer to www .barco.com Ultra Wide Fixed (EN53) 0.79 : 1 (0.8 - 3.3m) Wide Angle Fixed (EN52) 0.99 : 1 (1.0 - 10m) Long Throw Zoom (EN54) 2.68 - 4.1 ...

  • Barco CTHD-61B - page 25

    english 25 5 Overview Figure 5-10. Projector front Figure 5-11. Projector rear Figure 5-12. Projector top Remote Control Receiver Interchangeable Projection Lens Projection Lens Release Button Mains Power Connector Hot Air Exhaust Signal and Control Connector Panel Remote Control Receiver Keypad ...

  • Barco CTHD-61B - page 26

    26 CT series User Manual - Overview english Figure 5-13. Mounting features Figure 5-14. Projector left and right hand side Lamp Door Air Inlet Ceiling/Rig Mounting Features Accessory Mounting Features ...

  • Barco CTHD-61B - page 27

    english 27 5.1 Keypad and indicator Figure 5-15. Projector top key pad KEY VALUE POWER Power on or power off (standby) MENU Activate or deactivate on-screen menu system UP , DOWN, LEFT , RIGHT Select source when not in Shift or Menu mode Shift lens when not in Menu and after SHIFT/OK pressed Navigate when in Menu system SHIFT/OK Shift lens when not ...

  • Barco CTHD-61B - page 28

    28 CT series User Manual - Overview english 5.2 W ir eless r emote contr ol Figure 5-16. Remote control BUTTON FUNCTION POWER T urns projector ON/OFF INFO Shows Status menu; info on numbers & versions, lamp info * Activates the projector auto settings SHIFT Activates lens shift function # Reserved for future use OK/ARROWS Confirms the selectio ...

  • Barco CTHD-61B - page 29

    english 29 5.3 Connectors Figure 5-17. Connector panel (see technical data for details) 5.3.1 Signal connectors CONNECTOR NAME CONNECTOR TYPE FUNCTION HDBaseT RJ45 Video over twisted pair DVI DVI-I*) dual link Digital video (dual-link) HDMI HDMI type A Digital video DP (DisplayPort) DP Digital video (2) VGA 9 pin mini DSUB Analog RGBHV video 3G-SDI ...

  • Barco CTHD-61B - page 30

    30 CT series User Manual - Overview english 5.4 Menu system The various projector -settings can be controlled via the on-scr een menu system. The menu system is accessed by the keypad on the projector or using the wir eless remote contr ol. Press the MENU key to enter or leave the menu system. Navigate the options using the arrow-keys. Select optio ...

  • Barco CTHD-61B - page 31

    english 31 5.5 3D main menu The 3D menu contains settings for turning 3D on and off, in addition to defining various aspects of setup using Dual Head and specifying the types of glasses to be used. 3D : Offers the possibility to switch the 3D function of f and to chose between the following alternatives for setup: off, side by side (<60Hz only) ...

  • Barco CTHD-61B - page 32

    32 CT series User Manual - Overview english 5.5.1 3D > Dual head setup sub menu source 1: Choice of source. Alternatives are SDI1, SDI2, DVI, HDMI, VGA, HDBaseT , DisplayPort1, DisplayPort 2. For possible setup combinations, see Figure 5-18. Dual head setup possibilities. source 2: Choice of source. Alternatives are SDI1, SDI2, DVI, HDMI, VGA, H ...

  • Barco CTHD-61B - page 33

    english 33 5.6 Pictur e main menu The picture menu contains basic and advanced settings and adjustments for detailed pictur e enhancement control. All adjustments ar e global and are stor ed indepentantly of sour ce. The exception is 2D/3D for which the profiles ar e stored individually . profile: A selection of predefined profiles with dif fer ...

  • Barco CTHD-61B - page 34

    34 CT series User Manual - Overview english 5.6.1 Picture > RealColor sub menu BrilliantColor™ : T exas Instruments DLP™ color processing. 3 settings*: Bright: Max brightness, boosted color profile for highest per ceived brightness. In this mode all segments and spokes of the color wheel are in use. Color: Max brightness, balanced color pro ...

  • Barco CTHD-61B - page 35

    english 35 5.6.2 Picture > Advanced sub menu horizontal position : Shifts the image sideways (VGA only) vertical position: Shifts the image up or down (VGA only) phase : Adjust for stable image. A jittery image may appear with certain VGA sources. Y ou may also press the AUTO button on the keypad or remote contr ol to optimize. frequency: Adjust ...

  • Barco CTHD-61B - page 36

    36 CT series User Manual - Overview english 5.7 Installation main menu image orientation : Rotate the image on the imaging device in desktop front, desktop r ear , ceiling front, ceiling r ear . source scan : Search thr ough all input connectors for an active signal or stay on one connector . IR front Enable or disable front IR-r eceiver . IR rear ...

  • Barco CTHD-61B - page 37

    english 37 5.7.1 Installation > EDID sub menu VGA : Define the detailed timing descriptor in the EDID data for VGA connector . Select between auto, WUXGA, 1080@60Hz, SX+, SXGA, 1366x768, 720@60Hz, 720@50Hz, XGA, SVGA, VGA. DVI : Define the detailed timing descriptor in the EDID data for DVI connector . Select between auto, WQXGA@60Hz, WUXGA@12 ...

  • Barco CTHD-61B - page 38

    38 CT series User Manual - Overview english 5.7.2 Installation > Synchronization sub menu 2D frame lock : Selects the 2D frame lock sync signal. Options for 2D frame lock: source, SYNC 1, SYNC 2, SYNC 3. SYNC 1: Selects usage of SYNC1 connector in 2D mode. Options for SYNC 1: input, display sync, SYNC 2, SYNC 3 SYNC 2: Selects usage of SYNC2 con ...

  • Barco CTHD-61B - page 39

    english 39 5.8 Settings main menu PIN code: Pr otect the projector fr om usage with a PIN. If enabled the projector will ask for the PIN at every start up. network : Set IP address, Subnet mask and default gateway TCP/UDP port number . DHCP is supported and is enabled by default, but can be disabled. factory reset: Restore all settings to the facto ...

  • Barco CTHD-61B - page 40

    40 CT series User Manual - Overview english 5.8.1 Settings > Pin Code sub menu PIN code enable: The PIN code is disabled by default. If you want to enable/disable the PIN code you have to enter the current PIN (Default PIN : 1234). When completed you can enable or disable the use of PIN code. If PIN is entered incorr ectly 3 times, it will ask f ...

  • Barco CTHD-61B - page 41

    english 41 5.8.2 Settings > Network sub menu change LAN settings: In this sub-menu you can switch the DHCP enabled function on or off. If off you can set a fixed IP-addr ess. LAN DHCP: DHCP is supported and is enabled by default, but can be disabled under change LAN settings LAN IP address: Info field stating the current LAN IP address. LAN su ...

  • Barco CTHD-61B - page 42

    42 CT series User Manual - Overview english 5.8.3 Settings > Factory Reset sub menu picture: Restores pictur e settings to factory default. 3D: Restores 3D settings to factory default. communication: Restores communication settings to factory default. RealColor TM : Restores RealColor TM settings to factory default. other: Restores other setting ...

  • Barco CTHD-61B - page 43

    english 43 5.9 Languages main menu Select the desired menu language. • Supported languages: English, French, German, Spanish, Norwegian, Swedish, Russian, Korean, Japanese,Chinese T raditional, Chinese Simplified, Portuguese, Italian. • Default: English ...

  • Barco CTHD-61B - page 44

    44 CT series User Manual - Overview english 5.10 Status main menu source information: Simple and advanced source information. synchronisation information: Displays the current synchronization information. Includes 2D framelock, 3D source sync and 3D display sync. part number: Projector part number . serial number: Projector serial number . manufact ...

  • Barco CTHD-61B - page 45

    english 45 5.10.1 Status > Source Information sub menu advanced: Access to sub menu for mor e settings depending on sour ce used. See 4.10.2 Status > Source Information > Advanced sub menu source 1: Info on which source is in use. format: Displays r esolution and frequency for the sour ce in use. source 2: Info on which source is in use. f ...

  • Barco CTHD-61B - page 46

    46 CT series User Manual - Overview english 5.10.2 Status > Source Information > Advanced sub menu resolution: Info on current sour ce resolution. total image size: Info on current horizontal and vertical image size. sync frequency : Info on current horizontal and vertical sync frequency for the pr ojector . pixelclock: Week of manufacturing. ...

  • Barco CTHD-61B - page 47

    english 47 5.10.3 Status > Source Synchr onisation sub menu 3D: Indicates which 3D mode is used. 2D frame lock: Indicates what the pr ojector locks to in 2D frequency: Shows the current frequency of the locking signal status: Indicates the locking status phase: Indicates phase between the source and the locking signal 3D source sync: Indicates w ...

  • Barco CTHD-61B - page 48

    48 CT series User Manual - Overview english ...

  • Barco CTHD-61B - page 49

    english 49 6 Functionality The various functions of the projector ar e described in detail in the following chapters. 6.1 Powering On and Of f 6.1.1 Manual power control Switch the projector between On and Standby using the POWER switch on the keypad or the wireless r emote control. The keypad STATUS indicator is blue when the projector is up and r ...

  • Barco CTHD-61B - page 50

    50 User Manual - Intr oduction english 6.3 Language The menu system has a total of 11 user -selectable languages available. The default language is English. The available languages are: • English • French • German • Spanish • Russian • Norwegian • Swedish • Korean • Japanese • Chinese Simplified • Chinese T raditional • Por ...

  • Barco CTHD-61B - page 51

    english 51 6.5 Lamp power The projection lamp can be run at dif ferent power levels. Higher levels give higher brightness and shorter lamp life time. Lower levels save energy , extend lifetime and reduce brightness. In the menu system, go to PICTURE > LAMP POWER and adjust the setting according to need. 6.6 Sour ce selection, sour ce scan The pr ...

  • Barco CTHD-61B - page 52

    52 User Manual - Intr oduction english 6.8 Picture by Pictur e (PbP) Y ou may choose to view two sources simultaneously as a picture by pictur e. The PbP-function allows viewing of two images side by side or on top of each other . Certain restrictions apply to how sour ces combine when using PbP . T o view PbP: • Enter the INST ALLA TION menu and ...

  • Barco CTHD-61B - page 53

    english 53 6.12 Softwar e upgrades When upgrading the software the pr ojector must always be in standby position! If you are or have been in ECO mode you MUST use the following procedure before upgrading your projector: 1. Start the projector 2. Disable the OSD mode in the OSD menu 3. Power off (enters standby and not ECO mode) 4. Disconnect and re ...

  • Barco CTHD-61B - page 54

    54 User Manual - Intr oduction english CT series User Manual - Functionality ...

  • Barco CTHD-61B - page 55

    english 55 7 Optimising the image The projector has powerful featur es for picture optimization. This chapter describes details in using these features. All color calibration is done using Bar co’ s proprietary RealColor™ solu - tion. 7.1 Calibration data All Barco pr ojectors are measur ed and calibrated with high pr ecision equipment at the f ...

  • Barco CTHD-61B - page 56

    56 User Manual - Intr oduction english 7.1.2 RealColor™ modes Before any color corr ection is applied to the image, RealColor™ must be enabled. Go to menu PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™. RealColor™ can operate in 3 modes: • Color temperature/white point correction only . • Red, Green, Blue, White corre ...

  • Barco CTHD-61B - page 57

    english 57 7.2 Setting a white point or color temperatur e After enabling RealColor™ set the color temperature in the menu PICTURE > REALCOLOR > TEMPERA TURE . V alues between 3200K and 9300K can be selected. These color temperatures ar e tracking the “black body curve”- the black curved line in the center of CIE Chart in Figure 7-1. Th ...

  • Barco CTHD-61B - page 58

    58 User Manual - Intr oduction english 7.3 Gamma The projector featur es a set of 6 built in gamma curves: Film 2.2, Film 2.4, Film 2.6, Film 2.8, Video 1, Video 2, Computer 1, Computer 2, Dynamic and DICOM 180 . The different gamma curves are displayed below . The names of the curves are descriptive for their r ecommended use. Using any of the com ...

  • Barco CTHD-61B - page 59

    english 59 Figure 7-4. Film 2.8 gamma Figure 7-5. Video 1 gamma Figure 7-6. Video 2 gamma ...

  • Barco CTHD-61B - page 60

    60 User Manual - Intr oduction english Figure 7-7. Computer 1 gamma Figure 7-8. Computer 2 gamma Figure 7-9. Dynamic gamma CT series User Manual - Optimising the image ...

  • Barco CTHD-61B - page 61

    english 61 Figure 7-10. DICOM 180 Lux* (example HB color wheel: other shapes with other alternatives) * Several DICOM settings (10, 60, 180, 250, 400 Lux - The higher Lux number (ambient light), the steeper the curve. ...

  • Barco CTHD-61B - page 62

    62 User Manual - Intr oduction english CT series User Manual - Optimising the image ...

  • Barco CTHD-61B - page 63

    english 63 8 T echnical specifications Please see www .barco.com for more technical information. ...

  • Barco CTHD-61B - page 64

    64 User Manual - Intr oduction english CT series User Manual - T echnical specifications ...

  • Barco CTHD-61B - page 65

    english 65 9 Lamp change The indicator on the keypad will turn RED when lamp life is expired. Change the lamp when lifetime expires. Always r eplace lamp with the same type and rating. USE ORIGINAL LAMPS O N LY. The lamp holder employs an electronic lamp timer that is tracking the life time of the lamp. Always disconnect the power cord and wait unt ...

  • Barco CTHD-61B - page 66

    66 User Manual - Intr oduction english F50 User Manual - Lamp change ...

  • Barco CTHD-61B - page 67

    ...

  • Barco CTHD-61B - page 68

    PRODUCTION ADDRESS Habornveien 53 1653 Gamle Fredrikstad Norway Model certification name: GP9 © 2014 Barco nv . All rights reserved. All brands and trade names are the property of their respective owners. Specifications subject to change without prior notice. All values are typical and may vary . Please visit our website for latest specificatio ...

Manufacturer Barco Category Video projector

Documents that we receive from a manufacturer of a Barco CTHD-61B can be divided into several groups. They are, among others:
- Barco technical drawings
- CTHD-61B manuals
- Barco product data sheets
- information booklets
- or energy labels Barco CTHD-61B
All of them are important, but the most important information from the point of view of use of the device are in the user manual Barco CTHD-61B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Barco CTHD-61B, service manual, brief instructions and user manuals Barco CTHD-61B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Barco CTHD-61B.

Similar manuals

A complete manual for the device Barco CTHD-61B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Barco CTHD-61B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Barco CTHD-61B.

A complete Barco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Barco CTHD-61B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Barco CTHD-61B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Barco CTHD-61B, that we can find in the current document
3. Tips how to use the basic functions of the device Barco CTHD-61B - which should help us in our first steps of using Barco CTHD-61B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Barco CTHD-61B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Barco CTHD-61B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Barco CTHD-61B?

Use the form below

If you did not solve your problem by using a manual Barco CTHD-61B, ask a question using the form below. If a user had a similar problem with Barco CTHD-61B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)