Manual Samsung SWL-3000AP

88 pages 3.34 mb
Download

Go to site of 88

Summary
  • Samsung SWL-3000AP - page 1

    SWL-3000AP Series Access Point User ’ s Guide * This User’ s Guide can be used on SWL-3000AP , 3000AP(DA), 3300AP and 3300AP(DA). ...

  • Samsung SWL-3000AP - page 2

    Notice when you establis h * W e recomm end you to av oid this places w here may be cause of perform ance decline or trouble. 1. Places with high humidity or wet condition 2. Places with ex treme temp erature(too hot or too cold) 3. Places where change of temperature is extreme 4. Places with a lo t of dusts 5. Places sealed with thick walls or sti ...

  • Samsung SWL-3000AP - page 3

    1. Introduction ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 1 2. Installation ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ ...

  • Samsung SWL-3000AP - page 4

    Also, this equipm ent is available for hom e use. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device m ust accept any interference received, including interference that may cause undesired operation. 13. Firm ware Upgrade U ...

  • Samsung SWL-3000AP - page 5

    1 1. Intr oduction Thank y ou for purchasing SAMSUNG S WL-3000AP Series Access Point(AP). This guide describes the installation and basic config uration of the Access Point. Standard Model is SWL-3300AP for example. AP Components ! SW L-3000AP Series Access Point ! W ireless LAN Card (I nternal for SWL-3300 and 3300(DA) models) ! RS-232C Serial Cab ...

  • Samsung SWL-3000AP - page 6

    2 ! The Front and Rear View of SWL-3300AP ! The Front and Rear View of SWL-3300AP(DA) DC in RS-232 C RJ-45 Connector Power Ethernet Wi r e l e s s St a t u s ...

  • Samsung SWL-3000AP - page 7

    3 2. Installation ① Choose the place with the consideration of power outlet and network connection (RJ - 45 Cable connection) to install the Access Point. ② Plug in the power cord to the power outlet and the power adapter. Plug in the DC output to “ DC in ” . Make sure that the “ Power ” LED is on. If the “ Power ” LED is not on, pl ...

  • Samsung SWL-3000AP - page 8

    4 ⑧ Insert Wireless LAN Card into your PC. Wireless LAN Cards are available both for desktop and notebook PCs. PCI Wireless LAN Card is used for the desktop PC where as the PCMCIA Wireless LAN Card is for the notebook PC only. For more information about PCI and PCMCIA Wireless LAN Cards, please visit http://www.magiclan.com . ⑨ Enter the same E ...

  • Samsung SWL-3000AP - page 9

    5 3 3 3 3 . AP Basic Setting Using AP Manager ① Execute AP Manager(SW L -3000AP Series, 4000AP Series Management Utility ) under MS-W indows 95/98/Me/2000/NT/XP operating sy stem. ② After choosin g AP, which will be used by use rs, on “L ist Box” of AP Manager using mouse, se lect [Ba sic] tab for any change s on setting. ③ AP information ...

  • Samsung SWL-3000AP - page 10

    6 ④ TCP/I P address environment is set on [Basic] Dialogue Box. ♦ Specify an IP address After consulting with your system administr ator, you enter IP Address, Subnet Mask and Gateway Address. ♦ Obtain an I P address automatically This setting is possible whe n AP is used for DHCP Clie nt. ⑤ Set ESS I D and Channel number. Description is a ...

  • Samsung SWL-3000AP - page 11

    7 ♦ Set Channel for AP use. Channel index should be between 1 and 14(differs from country to country ). Notice : If you are operating two or more Acc ess Points in the adjoin ing cells, keep the appropriate channel distance to avoid the interference. We recommend you to keep the distance of at least 4 channels in the adjoini ng cells. ⑥ Select ...

  • Samsung SWL-3000AP - page 12

    8 ⑧ When you click [Confirm & Apply] button to apply new configuration, “ Configuration Summary ” window, which shows new confi guration, will appear. ⑨ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑩ When you click [Appl y ] button, “ Password ” window will appear. The de fault passwor ...

  • Samsung SWL-3000AP - page 13

    9 ⑪ After y ou enter the password, click [ OK] button. ⑫ If you want to set default values, click [ Load Default values] button. Then, AP Configura tion will return to def ault setting. Resetting to Default V alues ...

  • Samsung SWL-3000AP - page 14

    10 4. PTP Sett i ng Using AP Manager ① PTP stands for Point to Point, and it is used to connect two divided networks into one usi n g AP a s Wi r e l e ss B r i d g e . I n this ca s e , AP ca nnot be u s e d f o r capabilities of Access Point. ② After execut ing AP Manager, select [ Radio] tab on “Tab Bar”. Select AP to set PTP on “L ist ...

  • Samsung SWL-3000AP - page 15

    11 ③ When Operation Mode of AP is selected for “Point-to-Point” on [Radio] Dialogue B ox, [Remote I D (PTP)] Box will appe ar to enter MAC ID of Wireless LAN Card on other AP, which will be connected by using PTP mode. ④ When [Edit] button on [Remote ID (PTP)] Box is selected, [MAC I D] Box, which is to enter(for entering) MAC ID of Wirel e ...

  • Samsung SWL-3000AP - page 16

    12 ⑤ ESSI D and Channel of two APs must be identical in PTP mode ⑥ When you click [Confirm & Apply] button to apply new configuration, “ Configuration Summary ” window, which shows new confi guration, will appear. Confirm MAC ID Settin g o f other W ireless LAN C ard to be connected usin g PTP Mode Enter the Same E SSID and Channel of t ...

  • Samsung SWL-3000AP - page 17

    13 ⑦ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑧ When y ou click [Apply ] button, “ Password ” window will appear. ⑨ After y ou enter the password, click [ OK] button. ⑩ When you click [Appl y ] button instead o f [C onfirm & Apply] button, “ Password ” window will appear immediat ...

  • Samsung SWL-3000AP - page 18

    14 new configuration. ⑪ After rebooting, choose selected proper AP on “ Li st Bo x ” . Then, t he selected AP set with PTP Mode can be confirm ed on [Selected AP ’ s Info] Group B ox as shown below. Confirm PTP Mode Setting ...

  • Samsung SWL-3000AP - page 19

    15 5. AML Setting Using AP Manager ① AML stands for Automatic Multi-link. Using AP as Wireless Bridge, it is used to connect several divided networks into one. It connects several [Slave]s with one main [Master]. ② After executing AP Manage r, click [Radio] tab on “Ta b Bar”. After selecting AP to set AML on “List Box” using mouse, set ...

  • Samsung SWL-3000AP - page 20

    16 ④ Select either “Master” or “Slave” for [Control Mode] on [Automatic Multi-link] Box. Basically, AML Mode consists of two or more APs, and set one for “Master” and the rest for “Sl ave”s. Conf irm AP Operation Mode Setting Setting AML Control M ode Confirm AML Control M ode Setting Default V alue for “Monito r Interval ” Re ...

  • Samsung SWL-3000AP - page 21

    17 ⑤ All of ESSI D and Channel of AP set in AML mode must be identical. ⑥ When you click [Confirm & Apply] button to apply new configuration, “ Configuration Summary ” window, which shows new confi guration, will appear. ⑦ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑧ When y ou click [A ...

  • Samsung SWL-3000AP - page 22

    18 ⑨ After y ou enter the password, click [ OK] button. ⑩ When you click [Appl y ] button instead o f [C onfirm & Apply] button, “ Password ” window will appear immediately skipping “ Configuration Summary ” window. After you enter the passwor d, click [OK] button to appl y new configuration. ⑪ After rebooting, choose selected pro ...

  • Samsung SWL-3000AP - page 23

    19 6. Bridge Table and Protocol Managem ent Using AP Manager ① Using AP Manager, list of Wired and Wireless Station(PC or AP) connec ted to current AP can be confi rmed. Also, it sets type of Protocol to receive and send selected data, which satisfy Protoc ol user wants, among data tr ansmitting through AP. ② When you select [Bridge] tab on “ ...

  • Samsung SWL-3000AP - page 24

    20 ④ [Age Time] on [Bridge Table] Management Box shows cycle of AP re freshing “Bridge Table”. The use of Default Values is recommended. ⑤ After selecting Station Type you want with Radio button to refresh Stations connected to current AP, click [Refresh Bridge Table] button to confirm. ⑥ [Bridge Table] Management Box enables confirmation ...

  • Samsung SWL-3000AP - page 25

    21 ⑩ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑪ When y ou click [Apply ] button, “ Password ” window will appear. ⑫ After y ou enter Password, click [ OK] button. Select “Enabled” Select Protocol W hich You Do Not W ant ...

  • Samsung SWL-3000AP - page 26

    22 7. NAT Setting Using AP Manager ① NAT stands for Network Address Tr anslation, and it is used to establish private network domain. Using NAT, an y desktop or notebook PC, which are connected to AP, m ay freel y use an y private IP Address. In this cas e, the private IP Address must have same Netwo rk Address assi gned for NAT I P Address. For ...

  • Samsung SWL-3000AP - page 27

    23 ③ When you click [Confirm & Apply] button to apply new configuration, “ Configuration Summary ” window, which shows new confi guration, will appear. ④ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑤ When y ou click [Apply ] button, “ Password ” window will appear. ⑥ After y ou ente ...

  • Samsung SWL-3000AP - page 28

    24 ⑦ When you click [Appl y ] button instead o f [C onfirm & Apply] button, “ Password ” window will appear immediately skipping “ Configuration Summary ” window. After you enter the passwor d, click [OK] button to appl y new configuration. ⑧ After rebooting, choose selected proper AP on “ Li st Bo x ” . Then, t he selected AP s ...

  • Samsung SWL-3000AP - page 29

    25 Sele ct “TCP/IP ” [Propert ies] of LAN Adapter to use on [Configuration] M enu. Set “IP Address” and “Subn e t Mask” on [IP Address] Menu. In this case, IP Address entered on “ IP A ddress” mus t have same Netw ork Address of IP Address of AP assigned fo r NA T .(Ref er step ① .) ...

  • Samsung SWL-3000AP - page 30

    26 Configuration has been completed for desktop or notebook PC to connect with AP. In this case, the specified IP Address of des ktop or notebook PC should have same ne twork address as se t by NAT setting.(Refer step ① .) Gateway Address mus t have same as “IP Addr ess” of AP assig ned by NA T Setting on “ New Gate way” of [Gateway] M en ...

  • Samsung SWL-3000AP - page 31

    27 8. DHCP Server Setting Using AP Manager ① DHCP stands for Dynamic Host Configuration Protocol, it is protocol that enables Network administra tor to manage and assig n IP Address in system centrall y . DHCP manages and assigns IP Address for network administrator, and it enables computer to get assi gned IP Address when it is connected to othe ...

  • Samsung SWL-3000AP - page 32

    28 Notice : When you select DHCP Serv er, the values on the window show information assigned to DHCP Client wi th IP Address. In most cases, values of “Gateway” and “Submask” are same as those of Gateway and Submask of current AP. ④ Click [Edit IP Scope] button, and the window below will appear. Scope of IP Address Assignable Lease T ime ...

  • Samsung SWL-3000AP - page 33

    29 ⑤ To set the scope of assignable I P Address, first check on [ Empty ] check box on the left. Then, “E mpty ” will be changed to “V alid”, and y ou can set the sc ope. ⑥ Enter the beginning value in “From”, and ending value in “To”. ⑦ When you c omplete to set the scope of assignable I P Address, click [Clear IP Allocation ...

  • Samsung SWL-3000AP - page 34

    30 ⑪ After y ou enter the password, click [ OK] button. ⑫ When you click [Appl y ] button instead o f [C onfirm & Apply] button, “ Password ” window will appear immediately skipping “ Configuration Summary ” window. After you enter the passwor d, click [OK] button to appl y new configuration. ⑬ After rebooting, choose selected pro ...

  • Samsung SWL-3000AP - page 35

    31 Notice : If you want to set DHCP Client instead of DHCP Server, select [ Basic] on “ Ta b Bar ” menu of AP . Then, select “ Obtain an IP address automatically ” from Dialogue Box. (Refer to step ④ of Chapter6.) Then, the selected AP gives up its own IP Address, and other AP using DHCP Server will assign it . When the setting is complet ...

  • Samsung SWL-3000AP - page 36

    32 9. NAT and DHCP Server Simultaneous Setting Using AP Manager ① After executi ng AP Manager, sel ect [ Server] ta b on “Tab Bar” t o set DHCP Server and NAT simultaneously . ② Please re fer to Chapter 10 for NAT Setting and Chapter 11 for DHCP Server Setting. This c hapter shows def ault values. Notice : In this case, IP Address as Gatewa ...

  • Samsung SWL-3000AP - page 37

    33 ③ When you click [Confirm & Apply] button to apply new configuration, “ Configuration Summary ” window, which shows new confi guration, will appear. ④ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑤ When y ou click [Apply ] button, “ Password ” window will appear. ⑥ After y ou ente ...

  • Samsung SWL-3000AP - page 38

    34 ⑦ When you click [Appl y ] button instead o f [C onfirm & Apply] button, “ Password ” window will appear immediately skipping “ Configuration Summary ” window. After you enter the passwor d, click [OK] button to appl y new configuration. ⑧ After rebooting, choose selected proper AP on “ Li st Bo x ” . Then, t he selected AP s ...

  • Samsung SWL-3000AP - page 39

    35 10. ADSL and Cable Modem Connection Setting Using AP Manager ① After executing AP Ma nager, click [Advanc ed] and [ I nternet Connection] on “Menu Bar” in the following order. Or click [Internet Connection] button on [Basic] Dialogue Box. ② Then the I nternet Connection Setup pag e(default pag e) will appea r. Select y our Internet conne ...

  • Samsung SWL-3000AP - page 40

    36 Notice : ADSL can generally be divided into two service types supporting PPPoE or PPTP, but PPPoE is more common. I f you don’t know your ADSL service t y pe, please che ck the Website or contact your ISP to find out service ty pe you are using . ③ Go to 10.1 for PPPoE, 10.2 for PPTP, and 10.3 for Cable Modem 10.1 Settings fo r ADSL – PPPo ...

  • Samsung SWL-3000AP - page 41

    37 ③ Set NAT and DHCP S erver referring Chapter 9. ④ Click [Finish] button to comple te setting . DHCP Server and NA T Setting ...

  • Samsung SWL-3000AP - page 42

    38 ⑤ A window will appear an d ask y ou to appl y new settings immediately. If you do not want to apply new settings, selec t [No(N)]. ⑥ If you click [Yes(Y)] button, “Password” window will appear. After you enter the password, click [OK ] button to apply. In case you select [No(N)] button, new settings will be saved. If y ou want to contin ...

  • Samsung SWL-3000AP - page 43

    39 10.2 Settings f or ADSL – PPTP ① When the above page appears, ente r the user name given b y your ISP(Internet Service Provider) i n the “User Name” box . ② Enter the password in the “Password” box. ③ Enter the I P Address of PPTP Server in the “PPTP Server IP Address” box Notice : In case IP Address of PPTP Server are unknow ...

  • Samsung SWL-3000AP - page 44

    40 ④ Set NAT and DHCP S erver referring Chapter 9. ⑤ Click [Finish] button to comple te setting . Setting DHCP Server and NA T ...

  • Samsung SWL-3000AP - page 45

    41 ⑥ A window will appear an d ask y ou to appl y new settings immediately. If you do not want to apply new settings, selec t [No(N)]. ⑦ If you click [Yes(Y)] button, “Password” window will appear. After you enter the password, click [OK ] button to apply. In case you select [No(N)] button, new settings will be saved. If y ou want to contin ...

  • Samsung SWL-3000AP - page 46

    42 10.3 Settings for Cable Modem ① Set NAT and DHCP S erver referring Chapter 9. Notice : Personal Information Setting is not needed because Cable modems are generally given with fixed IP Address. ② Click [Finish] button to comple te setting . Setting DHCP Server and NA T ...

  • Samsung SWL-3000AP - page 47

    43 ③ A window will appear an d ask y ou to appl y new settings immediately. If you do not want to apply new settings, selec t [No(N)]. ④ If you click [Yes(Y)] button, “Password” window will appear. After you enter the password, click [OK ] button to apply. In case you select [No(N)] button, new settings will be saved. If y ou want to contin ...

  • Samsung SWL-3000AP - page 48

    44 11. Encryption Setting Using AP Manager ① After ex ecuting AP M anager, sele ct [S ecurity] tab on “Tab Bar” to set encry ption. Then, select “Encryption”. ② Select either “64(40 )-bit Key” or “128-bit Ke y.” The window below shows “64(40)-bit Key ” setting . ③ When y ou select [Set WEP Ke y] button, a window for WEP Ke ...

  • Samsung SWL-3000AP - page 49

    45 ④ Enter the agreed password phrase to set encr yption in “Passphrase,” and click [Generate] button to create W EP Key. After generating the k eys, select on e key among “De fault Key”s. Click [OK] button to complete setting of the key to be used for encry ption. Notice : In this case, WEP Keys should be gene rated using same Passphrase ...

  • Samsung SWL-3000AP - page 50

    46 ⑥ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑦ When “ Password ” window appear, enter the password. Then click [OK] button. ⑧ After rebooting, choose selected proper AP on “ List Box ” . Then, the selected AP set with Encryption can be confirmed on [Selected AP ’ s Info] Group Box a ...

  • Samsung SWL-3000AP - page 51

    47 12. User Access Control Setting Using AP Manager ① “User Access Control” is function that shows permission of using AP to MAC ID Table of Wireless LAN Card installed on certain Stations among desktop or notebook PC, which are connected AP. If you want to use this function, select “User Access Control” on [Security] Dialogue B ox. ② T ...

  • Samsung SWL-3000AP - page 52

    48 Click [+] icon, and enter MAC ID as shown on the window below. Then, click [OK] button to add MAC ID on [Allowed Table]. Select Connection Deny ...

  • Samsung SWL-3000AP - page 53

    49 ⑥ When you wa nt to deny specific MAC ID and permit the othe r, select “ pass” on [Other Stations] Box. Then, add the MAC ID on [Denied Table], which is you want to deny. MAC ID c an be enter ed b y the method explained on ⑤ and also move MAC I D from [Allowed Table]. ⑦ To move MAC ID from [Allowed Table] to [Denied Table], use [>&g ...

  • Samsung SWL-3000AP - page 54

    50 ⑨ If you want to export and save MAC IDs registered either on [Allowed Table] or [Denied Table], click [Export] button. Then, it will be saved wher e user wants as “granted.lst” or “denied.lst”. You can rename the file name. # granted.lst -> MAC I D L ist on [Allowed Table] # denied.lst -> MAC I D L ist on [Denied Table] On the o ...

  • Samsung SWL-3000AP - page 55

    51 ⑩ You can combine a nd use various setting s as y ou wish. ⑪ If new settings are enter ed correctly, click [Apply ] button to appl y new configuration. ⑫ When “Password” window appea r, enter the pass word. Then, click [OK] button. ...

  • Samsung SWL-3000AP - page 56

    52 13. Firm w are Upgrade Using AP Manager ① Whenever the new version of AP Firmware is a vailable, you can upgrade AP firmware into higher version using AP Manag er. ② After executi ng AP Manager, select [Firmware] t ab on “Tab Bar”. ③ Dialogue Box of the Firmware up grade is lik e what is view in the window below. ④ The current fir mw ...

  • Samsung SWL-3000AP - page 57

    53 ⑤ Downloaded the latest version of AP firmware in local disk of y our PC Notice : AP firmware corresponding to your AP can be downloaded in MagicLAN home page. ⑥ Click the file icon shown below on Dialogue Box. ⑦ After sele ct the firmware image f ile, click [Open] button. File Icon ...

  • Samsung SWL-3000AP - page 58

    54 ⑧ Click the [L oad] button after the file is select ed. T hen, “Password” window will be display ed. ⑨ Enter the password, default password is “public”, and click [OK] button. The AP firmware is lo ad ed from your Local Disk t o th e Access Po int and is upgraded. The following window shows the status of loading the AP firmware ima g ...

  • Samsung SWL-3000AP - page 59

    55 14. Data Transm ission Status Check Using AP Manager ① Data transmission traffic status of current AP can be confirmed using AP Manager. ② When [Statistics] tab on “Tab Bar” of AP Manager is selected, a window, which shows [Traf fic Selection] Box on Dialo gue Box to select T raffic t ype and shows relate d information below, will appe a ...

  • Samsung SWL-3000AP - page 60

    56 ⑤ If you want to confirm with line graph, select “L ine” instead of “Histo gram” on Related I nformation Confirm B ox . ⑥ In this case, if confirm is impossible due to increased number of pa ckets with wired and wireless transmission, increase s cope of number of packet transmitted per second(packet/sec) to confirm. ⑦ When selecti ...

  • Samsung SWL-3000AP - page 61

    57 # SNMP : Simple Network Management Protocol # MIB : Management Information B ase ⑨ Confirming Traffic information y ou want enables more efficient AP operation. Related Information Confirm Box Select MIB Ty p e ...

  • Samsung SWL-3000AP - page 62

    58 15. AP Setting Using Web Browser ① Open Web Browser. (Bey ond IE 4.0 or Netscape 4.0) ② Enter AP’s I P Address on “Address” of the Web Browser. Press [ENTER : ↵ ] key. ③ “Enter Network Passwor d” window appears. Do n ot enter the User Name. Enter the password. (The d efault value is “public”, and user can chan ge the passwo ...

  • Samsung SWL-3000AP - page 63

    59 ④ I nternet Connec tion Setting pag e”(default pag e) appears. ⑤ Simple C onfiguration Mode is f or Setting of Internet Connection Environment, and refer to “ 10. ADSL and Cable Modem Connection Setting Using AP Manager ”. ⑥ Expert Mod e is for Net work Administration, and ref er to “ 3. A P Basic S etting Using AP Manager ”. ...

  • Samsung SWL-3000AP - page 64

    60 16. AP Setting Using TELNET ① Open “Run” on [Start] menu of desktop and notebook PC. Enter the IP Address for I nternet Connection as following Example. Example) telnet ***.***.***.*** (IP Address ) Click [OK] button. ② Telnet order window appears, and please refe r to “ 18. AP Basic Setting Using RS-232C(COM Port) ” ...

  • Samsung SWL-3000AP - page 65

    61 17. HyperTerminal Setting for RS-232C(COM Port) Comm unication ① Execute th e HyperTerm inal under MS-W indows 95/98/Me/2000/NT/XP operating sy stem by following the steps below. Execute Hypertrm.exe file in “HyperTerminal” folder. ② After executing the H ypertrm.exe file, the following window will be displayed on MS-Windows. ...

  • Samsung SWL-3000AP - page 66

    62 ③ As displayed above, type “ AP MANAGER ” in the name field, and click [OK] button. You can enter any name you wish for the connection. ④ Select the modem port a s shown in the window below, and click [OK] button. (I n most of the cases, sel ect either “ Direct to Com1 ” or “ Direct to Com 2 ”.) ⑤ You will view the following wi ...

  • Samsung SWL-3000AP - page 67

    63 ⑥ If all the steps above ar e executed corre ctly, then the following menu w ill be displayed on the Hy p erT erminal window. The default password is “public”, and user can change password later. ⑦ When the password is entered, th e following [ROOT] menu appears on the Hy perTerminal window. ⑧ W hen AP setting proced ure is completed, ...

  • Samsung SWL-3000AP - page 68

    64 18. AP Basic Setting Using RS-232C( C O M Port) ① Choose [Basic] menu on [ROOT] menu. ② Select the f ollowing order to set Wireless L AN ESSID. Enter the proper ESSID (strings up to 32 characters) on “Enter new E SSID {Max. 32 ASCII}:” , and press [ENTER : ↵ ]. ESSID must consist of alphabetic and num eric char acters, ex cluding s pac ...

  • Samsung SWL-3000AP - page 69

    65 ③ Select the following order to change Wireless Channel. Enter the proper channe l number after the phrase “ Enter new Channe l {1- 14}: ”. Then, press [ENTER : ↵ ]. Channel inde x should be between 1 and 14(differs from country to country). Notice : If you are oper ating two or more Acces s Points in t he adjoining cells, keep the appro ...

  • Samsung SWL-3000AP - page 70

    66 ⑥ Select the following order to set Subnet Mask. Enter the proper subnet mask after the phrase “ Enter ne w Subnet M ask : ”. Then, press [ENTER : ↵ ]. Consult y our system administrator for setting the subnet mask. ⑦ Select the following order to set Gateway Address. Enter the proper Gate way Add ress afte r “ Enter n ew Gateway Add ...

  • Samsung SWL-3000AP - page 71

    67 ⑨ I f y ou want to change Password, select the following order on [ROOT] menu. Select [Administration] menu on [ Advanced] Menu. Select “Change password” on [Administration] menu. ================================================== Samsung SW L-3300AP C onfiguration ================================================== [ ROOT ] 1. Basic [Menu] ...

  • Samsung SWL-3000AP - page 72

    68 Enter the current pass word (Max. 30 char acters) aft er “ Ente r curren t password (Max. 30 characters): ”. Then, press [ENTER : ↵ ]. Enter the new password (Ma x. 30 characters) af ter “ Ent er ne w password (Max. 30 characters): ” . Then, press [ENTER : ↵ ]. Enter the new password again aft er “ Enter new password again: ”. Th ...

  • Samsung SWL-3000AP - page 73

    69 ⑩ You must select “ Save and reboot ” on [ROOT] menu, after chan ging the appropriate parameters by entering the new values. By selecting the abov e menu, r ebooting will occur automaticall y. The modi fied parameter s of the AP wi ll be changed effectivel y after it is rebooted. After the rebooting, you will view the following window to a ...

  • Samsung SWL-3000AP - page 74

    70 ⑪ After following all the steps mentioned above, you can close the HyperTerminal window if there is no need fo r change or setting. Select [Basic] menu if y ou want to confirm the setting s. ================================================== Samsung SW L-3300AP C onfiguration ================================================== [ Basic ] 1. ESSI ...

  • Samsung SWL-3000AP - page 75

    71 19. Load default values Using RS-232C(CO M Port) ⑫ Select “Load default values” on [ROOT] menu ⑬ If y ou w a nt to s e t d e f a ult v a lu e s, e n t e r “ y ( y e s )” a f t e r “ Do y ou r e al l y want (y /n)? ” then, press [Enter: ↵ ]. AP configur ation will return to de fault setting . ⑭ If all the steps above are execu ...

  • Samsung SWL-3000AP - page 76

    72 20. Firm w are Upgrade Using RS-232C(COM Port) ① Click the “Hy perterminal icon” saved in hard disk of your PC’ ② “Enter password” menu will be displayed on the HyperTerminal window. The default password is “public”, ③ When the password is entered, [ ROOT] menu appears on the HyperTerminal window. ④ Downloaded the latest ve ...

  • Samsung SWL-3000AP - page 77

    73 ⑥ If you want to upgrade the AP firmware, enter “y(yes)” a fter “ Do you re ally want to u pgrade the f irmware via serial ? ” then, press [ Enter: ↵ ]. Ente r “y (yes)” again after “Do y ou really want (y /n)? ”, then press [ Enter: ↵ ]. The following window will be display ed. ⑦ Enter the “apfirm ” after “ CMD: ? ...

  • Samsung SWL-3000AP - page 78

    74 ⑧ Select [transfer] menu on “Menu Bar” then, select “Send File“. ⑨ Click [Browse] button on the “Send File” window ⑩ After select the firmware image file on opened window , click [Open] button. ...

  • Samsung SWL-3000AP - page 79

    75 ⑪ “1K Xmodem” should be selected on Protocol, then click [send] button. The following window shows the status of loading the AP firmware image file to the AP. Notice: An error message will show up if AP firmware is not corresponding to your AP. ⑫ Firmware upgrade using RS-232C is recommended, onl y when “AP Manager” can not be used. ...

  • Samsung SWL-3000AP - page 80

    76 APPENDIX Ⅰ Ⅰ Ⅰ Ⅰ . Explanation of Basic Configuration to use AP Manager # E xplanation of AP E xternal Icons DC 5V Power LED(Green), it is alway s on. I EEE 802.3 Wired LAN Connection L ED(Orange), it is alway s on. I EEE 802.11 Wireless LAN Connection L ED(Green), it blinks. Status L ED(Red) - firmware upgrade / error occur # E xplanati ...

  • Samsung SWL-3000AP - page 81

    77 The window above shows “AP Manager” window. You can select menu from this “Menu Bar”. You can select each function of AP setting tabs on this “Tab Bar”. The very left icon shows currently selected tab. This “LED icon” shows Sending and Receiving status of AP and Transmission status of ADSL. Sending, Receivin g , and ADS L Transmi ...

  • Samsung SWL-3000AP - page 82

    78 “List Box” shows Access Points connected to sam e network se gment, and “Selected AP’s I nfo” shows simple information of selected AP . “Dialogue B ox ” is area for r eading and writing se tting values of AP. As shown above, each “Dialo gue Box” with different inform ation according to tab selected on “Tab Bar” appears. “ ...

  • Samsung SWL-3000AP - page 83

    79 This “Button Bar” consists of buttons showing AP Scan, Ente ring setting va lues , AP information and AP Manager information. This is “AP Monitor Window” when you click [Mode] button from “ Button Bar”. It shows APs connected around. Click [Mode] button to return to AP Manager mode. The window above is “Start IP Address Window” w ...

  • Samsung SWL-3000AP - page 84

    80 The window above sho ws “Configuration Summary”, and it appears when you select [Confirm & Apply ] button. This is “Password Window” for user authentication. Click [Apply] button to ope n this window. ...

  • Samsung SWL-3000AP - page 85

    81 APPENDIX Ⅱ Ⅱ Ⅱ Ⅱ . Specification Gener al Wi r el ess N e t w ork Ar c hit ec t ur e I E EE 802.1 1b( D SSS ) W i re d N e tw o rk A r c h i te c tu re Eth er net ( 10 / 100M bps) Powe r Adapt er 90 ~ 265VAC 4 7/63 H z to 5VD C 2A Cer t if ica t ion s EM C Em i ss i on : - F C C P a r t 15 C l as s B - EN 5 50 22 C l a ss B EM C I mm uni ...

  • Samsung SWL-3000AP - page 86

    82 Manag ement Fea tu res Local Conf igur at i on Se r ial EI A- 23 2 Remot e C onf i gur at i on - HTTP , Tel ne t , SNMP suppor t ed - AP Manag er for M i cr osof t Window s 95/ 98/ 2000/ N T Fir m war e Upg ra de Upgr adi ng via S er i al / E t her net I nt er f ace supp or t ed A uto ma ti c S ea rc h i n g A P Ea sy t o search t h e AP usi ng ...

  • Samsung SWL-3000AP - page 87

    83 Envir o nmen ta l In for mat io n O perat i n g Temperat u re 0 ℃ ℃ ℃ ℃ to 45 ℃ ℃ ℃ ℃ (32 ℉ ℉ ℉ ℉ to 1 13 ℉ ℉ ℉ ℉ ) S t orage T emper atur e -25 ℃ ℃ ℃ ℃ to 7 0 ℃ ℃ ℃ ℃ (- 1 3 ℉ ℉ ℉ ℉ to 1 5 8 ℉ ℉ ℉ ℉ ) Hum idi t y 95% N on- conden si ng Physi cal Chara cter i stics W L A N In te r f ...

  • Samsung SWL-3000AP - page 88

    W e value your feedback. If you find errors or omissions in this manuscript, or if you can suggest wa y s to improve its usefulness, we would be pleased to hear from y ou. Please contact us at : E-mail: wlanap@samsung.co.kr Y ou can find the latest firmware, software, and documents at: http://www .magiclan.com/ ...

Manufacturer Samsung Category Network Router

Documents that we receive from a manufacturer of a Samsung SWL-3000AP can be divided into several groups. They are, among others:
- Samsung technical drawings
- SWL-3000AP manuals
- Samsung product data sheets
- information booklets
- or energy labels Samsung SWL-3000AP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Samsung SWL-3000AP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Samsung SWL-3000AP, service manual, brief instructions and user manuals Samsung SWL-3000AP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Samsung SWL-3000AP.

Similar manuals

A complete manual for the device Samsung SWL-3000AP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Samsung SWL-3000AP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Samsung SWL-3000AP.

A complete Samsung manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Samsung SWL-3000AP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Samsung SWL-3000AP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Samsung SWL-3000AP, that we can find in the current document
3. Tips how to use the basic functions of the device Samsung SWL-3000AP - which should help us in our first steps of using Samsung SWL-3000AP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Samsung SWL-3000AP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Samsung SWL-3000AP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Samsung SWL-3000AP?

Use the form below

If you did not solve your problem by using a manual Samsung SWL-3000AP, ask a question using the form below. If a user had a similar problem with Samsung SWL-3000AP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)