Manual IBM LE-565

54 pages 0.99 mb
Download

Go to site of 54

Summary
  • IBM LE-565 - page 1

    LE-565 5.25 inc h Embedded Miniboar d User ’ s Manual Edition 1.0 2006/06/19 ...

  • IBM LE-565 - page 2

    LE-565 User ’ s Manual 2 Copyright Copyright 2006. All rights reserved. This document is copyright ed and all rights are reserved. The information in this docume nt is subject to change without prior notice to make improvements to the products. This document contains pr oprietary information and protected by copyr ight. No part of this document m ...

  • IBM LE-565 - page 3

    LE-565 User ’s Manual 3 Packing List Please check the package before y ou st arting setup the system Hardware: LE-565 series motherboard x 1 Cable Kit: Serial A T A Ribbon Cable x 2 44-pin A T A33 IDE Cable x 1 26-pin Slim T ype Floppy Cable x 1 Printed Matters: User ’s Manual x 1 Driver CD x 1 COM Port Cable x 1 40-pin A T A100 IDE Cable x 1 A ...

  • IBM LE-565 - page 4

    LE-565 User ’s Manual 4 Inde x Chapter 1 <Int roduction> ..................................................................................... 7 1.1 <Product Overview> ................................................................................. 7 1.2 <Product S pecification> ................................................. ...

  • IBM LE-565 - page 5

    LE-565 User ’s Manual 5 2.15.1 <Power Input> .......................................................................... 33 2.15.2 < Power Output >… …………………………………………………. 34 2.15.3 <Fan Co nnector>...................................................................... 34 2.16 <Indicator an ...

  • IBM LE-565 - page 6

    LE-565 User ’s Manual 6 (The Page is Lef t For Blank) ...

  • IBM LE-565 - page 7

    LE-565 User ’ s Manual Introduction Product Ov erv iew 7 Chapter 1 <Introduction> 1.1 <Product Overview> LE-565 is the 5.25 inch embedded minibo ard bas ed on VIA chipset. It integrates VIA embedded chipset for CN700 with VT8237R Plus, DDR 333/400 SDRAM, and serial A T A with RAID to provide the economical embedded plat form. VIA CN70 ...

  • IBM LE-565 - page 8

    LE-565 User ’ s Manual Introduction Product Specification 8 1.2 <Product Specification> General Specification Form Factor 5.25 inch miniboard CPU VIA V4/Eden 1.0GHz processor L1/L2 Cache: 128/128KB Front side bus: 400MHz Memory 1 x 184-pin DDR 333/400 S DRAM up to 1GB,onboard optional 256MB DDR SDRAM Unbufferred, none-ECC memory supported o ...

  • IBM LE-565 - page 9

    LE-565 User ’ s Manual Introduction Product Specification 9 Ethernet Interface Chipset REALTEK 8110S-32 Type 10Base-T / 100Base-TX /1000Base-TX auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector Four External RJ45 connectors wi th LED on rear I/O panel Audio Interface Chipset REALTEK ALC655 Interface 5.1 channel surround aud ...

  • IBM LE-565 - page 10

    LE-565 User ’ s Manual Introduction M e c h a n i c a l D r a w i n g 10 1.3 <Mechanical Drawing> ...

  • IBM LE-565 - page 11

    LE-565 User ’ s Manual Introduction Block Diagram 11 1.4 <Block Diagram> E d e n n a n o B G A 2 1 x 184-pin DDR333/400 U p to 1GB CRT/LCD Monitor VT1636 L VDS CN700 VT8237R+ Ultra V -Link 533MB/s 6 x USB2.0 Port s PCI 4 x 81 10S-32 LAN1/2/3/4 2 x SA TA AC97 A LC655 4 x Serial port s 1 x Floppy port 8-bit GPIO IrDA W83782G Hardware Monitor ...

  • IBM LE-565 - page 12

    LE-565 User ’s Manual Hardw are Setup C o n n e c t o r L o c a t i o n 12 Chapter 2 <Hardware Setup> 2.1 <Connector Location> MINIPCI CN_INV SYSF AN JFRNT IDE2 IDE1 CN_IR LPT CPUF AN CN_L VDS FDD PCI CN _ DIO JLED0/1/2/3 CN_PWR CN_USB2/3 CN_AUDIO CN_CRT CN_12V CN_COM2/3/4 CN_PS2 CDIN DIMM SA T A1/2 ...

  • IBM LE-565 - page 13

    LE-565 User ’s Manual Hardw are Setup Connector Location 13 D C _ I N L A N 1 / 2 / 3 / 4 C O M 1 U S B C R T CF ...

  • IBM LE-565 - page 14

    LE-565 User ’s Manual Hardw are Setup Jumper Reference 14 2.2 <Jumper Reference> Jumper Function JRTC CMOS Operating/Clear Setting JCFSEL Compact Flash address mode setting JVLCD LCD Panel Voltage Setting JA T AT/ATX mode setting JCSEL1/2 COM2 RS232/422/485 mode setting JCFSEL JVLCD JRTC JA T JCSEL1/2 ...

  • IBM LE-565 - page 15

    LE-565 User ’s Manual Hardw are Setup Connector Reference 15 2.3 <Connector Reference> 2.3.1 <Internal Connector> Connector Function Remark DIMM 184-pin DDR SDRAM DIMM S tandard IDE1 40-pin primary IDE connector S tandard IDE2 44-pin secondary IDE connector Slim FDD 26-pin slim type floppy connector Slim SA T A1/2 7-pin Serial A T A c ...

  • IBM LE-565 - page 16

    LE-565 User ’s Manual Hardw are Setup CPU and Memory Setup 16 2.4 <CPU and Memory Setup> 2.4.1< CPU> The board supports VIA Eden processor, default ratio is Eden 1G (400MHz) with heatsink only. 2.4.2 <Memory> The board supports one 184- pin DDR333/400 SDRAM and up to 1GB of capacity, only non-ECC, unbuffered memory is supported. ...

  • IBM LE-565 - page 17

    LE-565 User ’s Manual Hardw are Setup CMOS A TX Setup 17 2.5 <CMOS ATX Setup> The board’s data of CMOS can be setting in BIOS. If the board refus es to boot due to inappropriate CMOS setting s, here is how to proceed to clear (reset) t he CMOS to its default values. Jumper: JRTC T ype: Onboard 3-pin jumper JRTC Mode 1-2 Clear CMOS 2-3 Nor ...

  • IBM LE-565 - page 18

    LE-565 User ’s Manual Hardw are Setup Enhanced IDE&CF Interface 18 2.6 <Enhanced IDE & CF Interface> The board supports two enhance d IDE interface, dual channel f or 4 A T API devices with A T A33. Based on em bedded applicati on, the board has one 44-pin IDE connector + 5V supported for disk on module. The board also provides a Co ...

  • IBM LE-565 - page 19

    LE-565 User ’s Manual Hardw are Setup Serial A T A In terface 19 2.7 <Serial ATA Interface> Based on VIA VT8237R Plus Sout hbrid ge, the board supports tw o Serial ATA interfaces with RAID 0 and 1 array function. T he following is the list of the specif ication of the Seri al ATA. 1. Complies with Serial ATA Specification Revision 1.0 2. Du ...

  • IBM LE-565 - page 20

    LE-565 User ’s Manual Hardw are Setup Floppy Port 20 2.8 <Floppy Port> The board provides a slim type floppy por t; please use the 26-pin r ibbon cable in the package to connect the floppy device. FDD 4. Lif t up this plastic bar 5. Slot the cable in (Blue p aste for outside) 6. Press back the plastic bar Floppy rear side 1. Lif t up the br ...

  • IBM LE-565 - page 21

    LS-570 User ’s Manual Hardw are Setup LAN Interface 21 2.9 <LAN Interface> The board provides fo ur GigaLAN interfaces with REALTEK 8110S-32 PCI controller, and compliant with st andard IEEE 802.3 Et hernet interface for 100BASE-TX. LAN_1/2/3/4 ...

  • IBM LE-565 - page 22

    LE-565 User ’s Manual Hardw are Setup Onboard Display Interface 22 2.10 <Onboard Display Interface> Based on VIA CN700, the board s upports integrated S 3 Graphics UniChrome Pro IGP graphics, with BIOS select able 16/32/64MB shar ed with sy stem memory for frame buf fer . 2.10.1 <Analog VGA Interface> The board provides a DB15 CRT con ...

  • IBM LE-565 - page 23

    LS-570 User ’s Manual Hardw are Setup Digita l Display 23 2.10.2 <Digit al Display > The board provides one 40-pin L VDS conn ector for 18/24-bit single/d ual channel panels, supports up to 1600 x 1200 (U XGA) of resolution, with one LCD backlig ht inverter connector and one jumper for panel voltage setting 3 1 JVLCD CN_L VDS 39 2 1 1 5 CN_ ...

  • IBM LE-565 - page 24

    LE-565 User ’s Manual Hardw are Setup Digita l Display 24 Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header T ype: 3-pin Pow er select Header Connector model: JST B5B-XH-A Pin Description Pin Description 1 +12V 1 VCC(5V) 2 GND 2 LCDVCC 3 GND 3 VCC3(3.3) 4 GND 5 ENABKL Connector: CN_LVDS Type: onboard 40-pin connector for LVDS conne ...

  • IBM LE-565 - page 25

    LS-570 User ’s Manual Hardw are Setup Digita l Display 25 To setup the LCD, y ou need the component below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight power. 3. A LCD cable and an inverter cable. For the cables, pleas e follow the pin assignment of the connector to make a cabl e, because every panel has it s ow n pin a ...

  • IBM LE-565 - page 26

    LE-565 User ’s Manual Hardw are Setup Digita l Display 26 After setup the devices w ell, you need to select the LCD p anel type in the BIOS. The panel type mapping is list below : LE-565 BIOS panel type selection form VGA ROM VERSION: 9Y-9X-00-20 NO. Resolution Color Channel 0 640 x 480 18 1 1 800 x 600 18 1 2 1024 x 768 18 1 3 1280 x 768 18 1 4 ...

  • IBM LE-565 - page 27

    LS-570 User ’s Manual Hardw are Setup Onboard A udio Interface 27 2.11 <Onboard Audio Interface> The board provides the onboard AC97 5.1-channel audio interface with Realteck ALC655. Connector: CN_A UDIO Type: 10-pin (2 x 5) header (pitch = 2.54mm) Pin Description Pin Description 1 Line/SURR – Left 2 Ground 3 Line/SURR – Right 4 MIC1/CE ...

  • IBM LE-565 - page 28

    LE-565 User ’s Manual Hardw are Setup USB2.0 Interface 28 2.12 <USB2.0 Interface> Based on VIA VT8237R Plus, the board pr ovides 6 USB2.0 ports. The USB2.0 interface provides up to 480Mbps of transferring rate. Interface USB2.0 Controller VIA VT8237R+ T ransfer Rate Up to 480Mb/s Output V oltage 500mA USB 1 CN_USB 10 ...

  • IBM LE-565 - page 29

    LS-570 User ’s Manual Hardw are Setup USB2.0 Interface 29 Connector: CN_USB Type: 10-pin (5 x 2) header for USB2/3 Ports Pin Description Pin Description 1 VCC 2 VCC 3 Data0- 4 Data1- 5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C PS: The USB2.0 will be only active when you c onnecting with the USB2. 0 devices, if you insert an USB1.1 device, ...

  • IBM LE-565 - page 30

    LE-565 User ’s Manual Hardw are Setup GPIO Interface 30 2.13 <GPIO Interface> The board provides a programmable 8-bit digita l I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK. Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm Pin Description Pin Description 1 Ground 2 Ground 3 GP0 4 ...

  • IBM LE-565 - page 31

    LS-570 User ’s Manual Hardw are Setup Power and Fan Connector 31 2.14 <Serial Port Jumper Setting > The board provides four RS232 serial ports, with jumper selectable RS422/485 for COM2. Connector: CN_COM2/3/4 Type: 10-pin (5 x 2) header for COM2/3/4 Pin Description Pin Description 1 DCD/422RX-/485- 2 RXD/422RX+/485+ 3 TXD/422TX+ 4 DTR/422T ...

  • IBM LE-565 - page 32

    LE-565 User ’s Manual Hardw are Setup GPIO Interface 32 CN_COM2/3/4 10 1 COM JCSEL2 JCSEL1 ...

  • IBM LE-565 - page 33

    LS-570 User ’s Manual Hardw are Setup Power and Fan Connector 33 2.15 <Power and Fan Connector> The board comes with a 2-pin DC-Jack pow er connector for DC 12V input, it also has one 4-pin P4 additional use power connector for internal pow er supply , you can choose one pf them to meet your plication. 2.15.1 <Pow er Input> Connector: ...

  • IBM LE-565 - page 34

    LE-565 User ’s Manual Hardw are Setup Pow er Output 34 2.15.2 <Pow er Output> Connector: CN_PWR Type: 4-pin P-type connector for +5V/+12V output Pin Description Pin Description Pin Description Pin Description 1 +5V 2 Ground 3 Ground 4 + 12V Note: Maximum output voltage: 12V/5A & 5V/3A 2.15.3 <Fan Connector> Connector: CPUFAN , SYS ...

  • IBM LE-565 - page 35

    LS-570 User ’s Manual Hardw are Setup Indicator and Switch 35 2.16 <Indicator and Switch> The JFRNT provides front control panel of the b oard, such as p ower button, reset and beeper , etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header Function Signal PIN ...

  • IBM LE-565 - page 36

    LE-565 User ’s Manual 36 (This Page is Left For Blank) ...

  • IBM LE-565 - page 37

    LE-565 User ’ s Manual System Conf iguration SA TA RA ID Configuration 37 Chapter 3 <System Configuration> 3.1 <SATA RAID Configuration> The board supports t wo Serial ATA ports onboard, and s upports RAID 0, 1 and JBOD disk array, the RAID 0, 1 and JBOD are specified below : RAID 0 (S tripping) : T wo hard drives operating as one dri ...

  • IBM LE-565 - page 38

    LE-565 User ’s Manual SA TA RA ID Configuration 38 You also can edit disk array under OS, please inst all the VIA RAID Utility in the driver CD. (T o getting start, please click here to learn more infor mation) (Click here to build RAID 0) (Click here to build RAID JBOD) (Click here to build RAID 0) ...

  • IBM LE-565 - page 39

    LE-565 User ’ s Manual System Conf iguration A udio Configuration 39 3.2 <Audio Configuration> The board provides 5.1 cha nnel audio interface with driver installed, please install the Realtek ALC655 audio driver i n the CD before getting start to enjoy the 5.1 channel sound system. ...

  • IBM LE-565 - page 40

    LE-565 User ’s Manual Display Configuration 40 3.3 <Display Configuration> The board provides onboard ana log VGA interf ace, and optional digital di splay interface with LVDS , please install the VIA video driver before enjoy the vivid display. Based on the VIA CN700 with S3 UniCh rome Pro graphic, the board provid es dual display function ...

  • IBM LE-565 - page 41

    LE-565 User ’ s Manual System Conf iguration Display Configuration 41 T w o controllers for each display device There are two options for secondary display dev ice For more display properties setting, please click “A dvanced” button. ...

  • IBM LE-565 - page 42

    LE-565 User ’s Manual Display Configuration 42 Please select S3Display for advanced device setting. When you set dual display clone mode, y ou’ll see the same screen display on tw o devices. When you set the dual display for ext ended desktop mode, y ou can have the independent desktop on the second device. Connected Devices Click check box to ...

  • IBM LE-565 - page 43

    LE-565 User ’s Manual 43 (This Page is Left for Blank) ...

  • IBM LE-565 - page 44

    LE-565 User ’ s Manual BIOS Setup 44 Chapter 4 <BIOS Setup> The motherboard uses the A ward BIOS fo r the system config uration. The A ward BIOS in the single board computer is a cust omized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatib le CPU architecture based processo rs an ...

  • IBM LE-565 - page 45

    LE-565 User ’s Manual 45 (This Page is Left for Blank) ...

  • IBM LE-565 - page 46

    LE-565 User ’ s Manual I/O Port Pin Assignment IDE Port 46 Appendix A <I/O Port Pin Assignment> A.1 <IDE Port> Connector: IDE1 Type: 40-pin (20 x 2) box header Pin Description Pin Description 1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 VCC 21 REQ 22 Groun ...

  • IBM LE-565 - page 47

    LE-565 User ’ s Manual I/O Port Pin Assignment IDE Port 47 Connector: IDE2 Type: 44-pin (22 x 2) box header Pin Description Pin Description 1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23 IOW-/STOP 24 Ground 25 IOR-/HDMARDY 26 Ground 27 IORDY/DDMA ...

  • IBM LE-565 - page 48

    LE-565 User ’ s Manual I/O Port Pin Assignment Floppy Port 48 A.2 <Floppy Port> Connector: FDD Type: 26-pin connector Pin Description Pin Description 1 VCC 2 INDEX 3 VCC 4 DRV0 5 VCC 6 DSKCHG 7 DRV1 8 N/C 9 MTR1 10 MTR0 11 RPM 12 DIR 13 N/C 14 STEP 15 Ground 16 WRITE DATA 17 Ground 18 WRITE GATE 19 N/C 20 TRACK 0 21 N/C 22 WRPTR 23 Ground 2 ...

  • IBM LE-565 - page 49

    LE-565 User ’ s Manual I/O Port Pin Assignment CRT Port 49 A.4 < CRT Port > Connector: CRT Type: 15-pin D-sub female connector on panel Pin Description Pin Description Pin Description 1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 5VCDA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 LVGA5V 14 VSYNC 5 Ground 10 Ground 15 5VCLK A.5 <Serial A T A Port> Con ...

  • IBM LE-565 - page 50

    LE-565 User ’s Manual 50 A.7 <LAN Port> Connector: RJ45_1/2/3/4 Type: RJ45 connector with LED on rear panel Pin 1 2 3 4 5 6 7 8 Description TX+ TX- RX+ N/C N/C RX- N/C N/C Connector: JLED0/1/2/3 Type: 6-pin header for LAN LED Pin Description Pin Description 1 ACT+ 2 ACT- 3 Link100+ 4 Link100- 5 Link 1G+ 6 Link 1G- 1 8 1 6 ...

  • IBM LE-565 - page 51

    LE-565 User ’s Manual 51 (This Page is Left for Blank) ...

  • IBM LE-565 - page 52

    LE-565 User ’ s Manual Flash BIOS BIOS A uto Flash T ool 52 Appendix B <Flash BIOS> B.1 BIOS Auto Flash T ool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below : TU ht t p :/ / www. a war d .c o m UT TU ht t p :/ / www. c om m e ll . co m . t w/s upp ...

  • IBM LE-565 - page 53

    LE-565 User ’s Manual 53 (This Page is Lef t for Blank) ...

  • IBM LE-565 - page 54

    LE-565 User ’s Manual Con tact Information Conta ct Information 54 Contact Information Any advice or comment about our products and service, or anything we can help you please don’t hesitate to cont act with us. We will do our best to support you for your product s, projects and business. T aiwan Commate Computer Inc. Address 8F , No. 94, Sec. ...

Manufacturer IBM Category Switch

Documents that we receive from a manufacturer of a IBM LE-565 can be divided into several groups. They are, among others:
- IBM technical drawings
- LE-565 manuals
- IBM product data sheets
- information booklets
- or energy labels IBM LE-565
All of them are important, but the most important information from the point of view of use of the device are in the user manual IBM LE-565.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals IBM LE-565, service manual, brief instructions and user manuals IBM LE-565. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product IBM LE-565.

Similar manuals

A complete manual for the device IBM LE-565, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use IBM LE-565 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of IBM LE-565.

A complete IBM manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual IBM LE-565 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the IBM LE-565, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the IBM LE-565, that we can find in the current document
3. Tips how to use the basic functions of the device IBM LE-565 - which should help us in our first steps of using IBM LE-565
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with IBM LE-565
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of IBM LE-565 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning IBM LE-565?

Use the form below

If you did not solve your problem by using a manual IBM LE-565, ask a question using the form below. If a user had a similar problem with IBM LE-565 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)