English dropdown-ico

Manual First Alert FA148CPSSIA

40 pages 0.58 mb
Download

Go to site of 40

Summary
  • First Alert FA148CPSSIA - page 1

    Programming Guide ON OFF A RM E D READ Y A B C D 6 4 7 9 # 3 5 8 0 2 1 FA260 R AR M E D READY FA560 6 4 7 9 # 3 5 8 0 2 1 R AWAY STA Y PAGE K5305-5PRV5 11/08 Rev. B FA168CPS / FA168CPSSI FA168CPS / FA168CPSSI FA168CPS / FA168CPSSI FA168CPS / FA168CPSSI A A A A FA148CP / FA148CPSIA FA148CP / FA148CPSIA FA148CP / FA148CPSIA FA148CP / FA148CPSIA S S e ...

  • First Alert FA148CPSSIA - page 2

    – 2 – TA BLE OF CONTENTS PROGRAMM ING MO DE COM MANDS ...................................................................................................... ............... 3 DA TA FIELD PROGRA MM ING FORM .................................................................................................... ................. 4 CONFIGURABLE ZONE T ...

  • First Alert FA148CPSSIA - page 3

    – 3 – PROGRA MMING MODE COMMA NDS TO ENTER PROGRAMMING MODE (using an alpha keypad connected to the control) : A. POW ER UP, then press [ ✱ ] and [#] at the same time, w ithin 50 seconds of pow ering up (this method must be used if ✱ 98 was used to ex it program mode). OR B. Initially, key : Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0. PR ...

  • First Alert FA148CPSSIA - page 4

    – 4 – DA TA FIELD PROGRA MMING FORM Entries apply to the FA168CPS/FA168CPSSIA and FA148CP/ FA148CPSIA c ontrols, except entries s hown in dashed boxes, which apply only to the FA168CPS / FA168CPSSIA (partition ent ries) and are not appli cable to the FA 148CP/FA148CP SIA c ontrols . SIA -Compliant C ontrols : W here noted, certain fi elds have ...

  • First Alert FA148CPSSIA - page 5

    – 5 – ∗ ∗ ∗ ∗ 31 Single A larm Sounding P er Zone 0 = unlimited sounding 1 = one alarm sounding per zone SIA-Compliant Controls: If “0” selected, “alarm sounding per zone” will be the same as the “number of reports in armed period” set in field *93 (1 if one report, 2 if 2 reports, unlimited for zones in zone list 7). [0] If ...

  • First Alert FA148CPSSIA - page 6

    – 6 – ∗ ∗ ∗ ∗ 39 Power Up In Prev ious State 0 = no, alway s power up disarmed; 1 = yes, pow er up in previous state SIA-Compliant Controls: Feature alway s enabled; field does not exist. W hen the system powers up armed, an alarm w ill occur 1 minute after arming if a zone is faulted. Note that if the prev ious state was armed Away or ...

  • First Alert FA148CPSSIA - page 7

    – 7 – ∗ ∗ ∗ ∗ 50 Burglary Dialer Delay Delay Time: 0 = no delay 1 = 15 seconds 2 = 30 seconds 3 = 45 seconds SIA-Compliant Controls: Delay Time: 1 = 15 seconds 2 = 30 seconds 3 = 45 seconds Delay Disable : 0 = use delay set in entry 1 1 = dial delay disabled for zones listed in zone list 6 (use zone list 6 to enter those zones that requ ...

  • First Alert FA148CPSSIA - page 8

    – 8 – TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES ( ∗ ∗ ∗ ∗ 59 thru ∗ ∗ ∗ ∗ 68, *70 thru ∗ ∗ ∗ ∗ 76, and ∗ ∗ ∗ ∗ 89): For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. A 0 ( not #+10) in the first box disables a r ...

  • First Alert FA148CPSSIA - page 9

    – 9 – ∗ ∗ ∗ ∗ 66 Ar m Aw a y/ S t a y R p t C o d e See above for entries. [0,0,0,0,0 ,0] Away Stay Away Stay Away Stay Part. 1 Part. 2 Common This option allow s for independent programming of Away and Stay reports for each partition, including the common lobby. NOTE: “OPEN” reports are not sent if the associated closing report is ...

  • First Alert FA148CPSSIA - page 10

    – 10 – OUT PUT AND SYST EM SETUP ( ✱ 77 – ✱ 93) ∗ ∗ ∗ ∗ 77 Daylight S avings Time Start/End Month 0 = Disabled 1-9 = January-September (1 = Jan, 2 = Feb, etc) #+10 = October #+11 = November #+12 = December | [3][11 ] Enter the start and end month for daylight savings time, if applicable to the region. ∗ ∗ ∗ ∗ 78 Daylight S ...

  • First Alert FA148CPSSIA - page 11

    – 11 – ∗ ∗ ∗ ∗ 88 Program Mode Lockout Options 0 = standard *98 installer code lockout (reentry only by [ ∗ ] + [#] within 50 secs after power up) 1 = lockout [ ∗ ] + [#] reentry after *98 exit (reenter v ia installer code or downloader only ) 2 = not applicable (option doesn’t exist) 3 = lockout local programming after *98 exit ( ...

  • First Alert FA148CPSSIA - page 12

    – 12 – ∗ ∗ ∗ ∗ 93 Reports In A rmed Peri od Per Zone (Sw inger Suppression) Restrict Report Pairs: 0 = Unlimited Reports 1 = 1 report pair per zone per armed period 2 = 2 report pairs per zone per armed period SIA-Compliant Controls: Restrict Report Pairs: 1 = 1 report pair; 2 = 2 report pairs Unlimited Reports Enable: 0 = restrict repo ...

  • First Alert FA148CPSSIA - page 13

    – 13 – ∗ ∗ ∗ ∗ 160 Pager 1 Phone No. Enter up to 20 digits. 0–9 #+11 = ' ✱ ' #+12 = '#' #+13 = 2-second pause | | | | | | | | | | | | | | | | | | | If entering fewer than 20 digits, ex it by pressing [ ∗ ] + next field number. To clear entries, press ∗ 160 ∗ . ∗ ∗ ∗ ∗ 161 Pager 1 Characters Enter th ...

  • First Alert FA148CPSSIA - page 14

    – 14 – ∗ ∗ ∗ ∗ 171 Pager 4 Report Options See field *162 for reporting options. [0,0,0] P1 P2 comm Select for each partition (use zone list 12 for options 12 or 13). ∗ ∗ ∗ ∗ 172 Pager Dela y Option For A larms 0 = none 1 = 1 minute 2 = 2 minutes 3 = 3 minutes [3] This field determines the delay of alarm reports to the pager. T h ...

  • First Alert FA148CPSSIA - page 15

    – 15 – ∗ ∗ ∗ ∗ 182 Configurable Zone Type 9 0 (0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15). 1 2 3 4 5 6 7 8 9 10 Enter the appropriate value for each entry, 1-10, based on the charts provided in the Configurable Zone T ype W orksheet section. Each entry is the sum of the values of its selected options To calculate the val ...

  • First Alert FA148CPSSIA - page 16

    – 16 – KEYPA D OPT IONS *190-*199 To enable key pads: 1. Set desired address at keypad (refer to keypad’s instructions for setting the address). 2. Use data fields *190-*196 to enable keypad addresses, assign a partition, enable sound options in field. 3. Use fields *197, *198, and *199 to turn on partition number display, ex it time interval ...

  • First Alert FA148CPSSIA - page 17

    – 17 – CONFIGURA BLE ZONE TYPES WORKSHEETS Configurable zone types 90 and 91 can be program med via downloader s oftware or fr om a k eypad using data fields*182-*185. Conf igurable zone ty pes 92 and 93 (FA168CPS only) can only be program m ed using the downloader software. Program m ing Configurable Zone T ype options involves mak ing 10 entr ...

  • First Alert FA148CPSSIA - page 18

    – 18 – ∗ ∗ ∗ ∗ 56 ZONE PROGRA MMING MENU MODE (press *56 while in Program mode) The Zone Programming W orksheet is on page 36. Zones and Par titions Each protection zone needs to be programmed w ith various attributes using *56 Zone Programming mode or ✱ 58 Ex pert Programming Mode. U sing this mode, enter the zone number to be progra ...

  • First Alert FA148CPSSIA - page 19

    – 19 – 10 Report Code 1st 01 2nd 00 10 Report Code (RC) First Digit: 1-9, 10 for 0, 11 for B, 12 for C, 13 for D, 14 f or E, 15 for F 00 to disable Second Digit: same as above [ ∗ ] to continue Enter the report code for this zone, w hich consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report ...

  • First Alert FA148CPSSIA - page 20

    – 20 – 10 INPUT S/N L A022-4064 ? Loop Number Change [ ∗ ] to continue NOTE: If the [C] key is used to copy the previously enrolled serial number, the cursor will mov e to the Loop column (L) with the previous serial number displayed, and display a highlighted question mark for the loop number. Enter the loop number and press [ ✱ ]. The sys ...

  • First Alert FA148CPSSIA - page 21

    – 21 – Zn ZT P RC IN: L 10 00 1 10 RF 1 Zone Progra mming ZT = see Zone Type chart shown in *56 M enu Mode “Zone T ype” prompt P = partition 1, 2, 3 (common); RC = 1 (send CID report); 0 (no report) IN = input type; L = loop number [ ∗ ] to continue A summary screen w ith the selected zone’s current programming appears. Begin programmin ...

  • First Alert FA148CPSSIA - page 22

    – 22 – XM IT TO CONFIRM PRESS ✱ TO SKIP Confirm [ ∗ ] to continue • If “Yes” w as entered at the SET TO CONFIRM? prompt previously (see first prompt follow ing entry into the ∗ 58 Expert Programming M ode), the display on the left will appear. Confirm serial and loop numbers by activating the wire less key. IMPORTANT: W hen confirme ...

  • First Alert FA148CPSSIA - page 23

    – 23 – ∗ ∗ ∗ ∗ 57 FUNCTION KEY PROGRA MMING MENU MODE (press ∗ ∗ ∗ ∗ 57 while in Data Programming mode) . The system prov ides the ability to program each of the four keypad function keys to perform one of 12 system operations. The end user can then activate the function by simply pressing and holding the programmed key for 2 se ...

  • First Alert FA148CPSSIA - page 24

    – 24 – OUTPUT DEVICE PROGRA MMING GENERAL INFORMA TION (*79/*80 Menu Mode) Output Devices: T he FA168CPS system supports up to 16 relays and/or Powerline Carrier dev ices (X-10 devices) plus 2 built-in trigger outputs in any combination. These 18 “outputs” are assigned to sy stem-wide output numbers (01-18). Use *79 M enu Mode to assign out ...

  • First Alert FA148CPSSIA - page 25

    – 25 – XX OUTPUT TYPE DELETE 0 Output Type 0 = delete 1 = relay on 4204/4229 module 2 = Powerline Carrier dev ice (X-10) [ ∗ ] to continue Select whether this is a relay or a Powerline Carrier (X -10) device. If Powerline Carrier is selected, go to “A” prompt. If relay is selected, skip to “B” prompt. “ A ” XX UNI T No. yy Unit Nu ...

  • First Alert FA148CPSSIA - page 26

    – 26 – 80 Menu Mode Output Funct. # (00 = Quit) 01 Output Function No. (FA168CPS: 01-48 (FA148CP: 01-24) [ ∗ ] to continue; 00 to quit Enter the output function number to be defined (or 00 to exit) 01 A E P Trig ?00 0 0 – ZL=00 Summary Screen [ ∗ ] to continue This screen displays a summary of the current output programming (for this exam ...

  • First Alert FA148CPSSIA - page 27

    – 27 – “ C ” 01 Enter Zn No. 12 Zone Number Press [ ✱ ] to continue. (prompt appears if zone number was selected) Enter the desired zone number associated w ith this output number. At the ENTER EVENT prompt, enter the z one event that will activ ate this output. 01 Enter Event 0 = restore; 1 = alarm/fault/trouble Restore 0 Press [ ✱ ] t ...

  • First Alert FA148CPSSIA - page 28

    – 28 – 01 Delete Zone? 0 = No 1 = Yes 0 Deleting a Zone 0 = don’t delete zones 1 = go to next prompt to delete zones [ ∗ ] to continue To save the z one list, enter 0 and the system returns to the Zone List No. prompt. To delete a zone or z ones in a zone list, enter 1 to continue. 01 Zn to Delete? (00 = Quit) 00 Delete the Zone 01-64 † = ...

  • First Alert FA148CPSSIA - page 29

    – 29 – EXAM PLE: (a) ✱ ZN 01 B ACK (b) ✱ ZN 01 BACK (c) ✱ ZN 01 BACK D OOR (d) ✱ ZN 01 BACK DOOR Descriptor Example EXAM PLE: “BACK DOOR” a. From the list, BACK = 013, so, after entering the zone number to be edited (step 1), enter #013. If you accidentally enter the wrong w ord, simply press [#] plus the correct 3-di g it number fo ...

  • First Alert FA148CPSSIA - page 30

    – 30 – A LPHA VOCA BULARY LIST (For Entering Zone Descriptors) 000 (Word Spac e) – A – • 001 A IR • 002 ALARM ∗ ∗ ∗ ∗ 004 A LLEY 005 A MBUSH • 006 A REA • 007 A PA RTMENT • 009 ATTIC ∗ ∗ ∗ ∗ 010 A UDIO – B – • 012 BABY ∗ ∗ ∗ ∗ • 013 BACK ∗ ∗ ∗ ∗ • 014 BA R • 016 BASEMENT ∗ ∗ ∗ ∗ ...

  • First Alert FA148CPSSIA - page 31

    – 31 – SETTING SCHEDULES (Install er Code + [#] + [6] [4]) The system prov ides schedules, which can be used to automatically control 11 types of system ev ents at pre-defined times. Some events are reserved for the installer only . FA168CPS: Provides up to 32 schedules: 16 schedules for use by the end-user, 16 for use by the installer. FA148CP ...

  • First Alert FA148CPSSIA - page 32

    – 32 – REPEAT OPTION 0-4 X Repeat Option 0 = do not repeat 1 = repeat weekly 2 = repeat biweekly (every other week) 3 = repeat every third w eek 4 = repeat every fourth w eek Press [ ∗ ] to continue. Enter the desired repeat option for this schedule. e.g., To make a schedule that happens every day you would select all days w ith a repeat coun ...

  • First Alert FA148CPSSIA - page 33

    – 33 – ∗ ∗ ∗ ∗ 29 COMMUNICA TION DEVICE MENU MODE (Pass-Through Programming) This mode is for programming an IP, GSM , or IP/GSM Communicator M odule using an alpha keypad. Alternatively, these options can be programmed via the AlarmNet Direct w ebsite. After programming is complete, the module must be registered with AlarmNet before re ...

  • First Alert FA148CPSSIA - page 34

    – 34 – ZONE TYPE DEFINITIONS Zone types define the way in which the system responds to f aults in each zone. Ty pe 00 Zone Not Used Program a zone with t his zone type if the zone is not used. Ty pe 01 Entry /Exit Burgla ry # 1 • Assign t o zones that are us ed for prim ary entry and exit. • Provides entry delay when zone is f aulted if con ...

  • First Alert FA148CPSSIA - page 35

    – 35 – UL NOTICES 1. Entry Delay No. 1 and No. 2 (fields ∗ 35, ∗ 36) cannot be greater than 30 seconds for UL Residential Burglar Alarm installations, and entry delay plus dial delay should not exceed 1 minute. For U L Commercial Burglar Alarm installations, total entry delay may not exceed 45 seconds. 2. For UL Commercial Burglar Alarm and ...

  • First Alert FA148CPSSIA - page 36

    – 36 – WORKSHEET FOR ∗ ∗ ∗ ∗ 56 ZONE PROGRA MMING (FA148CP supports up to 32 zones: 1-6, 9-34, 49-56) [default show n in brackets] Zone Zn Type Part. Repor t Hardwire Type Rsp. Time Location 1 [09] [1] [EOL] [1] 2 [01] [1] [EOL] [1] 3 [03] [1] [EOL] [1] 4 [03] [1] [EOL] [1] 5 [03] [1] [EOL] [1] 6 [03] [1] [EOL] [1] 7 [03] [1] [EOL] [1] ...

  • First Alert FA148CPSSIA - page 37

    – 37 – WORKSHEET FOR ∗ ∗ ∗ ∗ 57 FUNCTION KEY PROGRA MMING Option Function A B C D Comments 01 Paging 02 Time Di splay 03 Arm AW AY 04 Arm STAY 05 Arm NIGHT-STAY 06 Step Arm ing 07 Device Activ ation Device : 08 Comm . Test 09 Macro Key 1 10 Macro Key 2 11 Macro Key 3 12 Macro Key 4 00 Em ergency Keys: zone 95 zone 99 zone 96 paging Pers ...

  • First Alert FA148CPSSIA - page 38

    – 38 – WORKSHEET FOR ∗ ∗ ∗ ∗ 80 OUTPUT FUNCTION PROGRA MMING Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you enter the data during the displays and prompts that appear in sequence. Notes: 1. For Relays, 4229 and 4204 devices are programmed in * 79, *80, and *81 mode ...

  • First Alert FA148CPSSIA - page 39

    – 39 – WORKSHEET FOR SCHEDULES (install er code + [#] + [ 6] [4]; master code c an only acc ess s chedules 01-16 f or FA168CPS, 01-04 f or FA148CP, and ev ents 00-07 for bot h controls ; FA148CP s upports up to 8 s chedules, FA168CPS s upports up to 32 s chedules ) No. Event Device No. G roup No. Partition Start Time/ Stop Time/ Repeat Random ( ...

  • First Alert FA148CPSSIA - page 40

    5800 SERIES TRA NSMITTER INPUT LOOP IDEN TIFICA TION All of the transmitters illustrated have one or more unique factory assigned input (loop) ID numbers. Each of the inputs requires its own programming z one (e.g., a 5804's four inputs require four programming zones). For information on any transmitter not shown, refer to the instructions acc ...

Manufacturer First Alert Category Home Security System

Documents that we receive from a manufacturer of a First Alert FA148CPSSIA can be divided into several groups. They are, among others:
- First Alert technical drawings
- FA148CPSSIA manuals
- First Alert product data sheets
- information booklets
- or energy labels First Alert FA148CPSSIA
All of them are important, but the most important information from the point of view of use of the device are in the user manual First Alert FA148CPSSIA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals First Alert FA148CPSSIA, service manual, brief instructions and user manuals First Alert FA148CPSSIA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product First Alert FA148CPSSIA.

Similar manuals

A complete manual for the device First Alert FA148CPSSIA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use First Alert FA148CPSSIA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of First Alert FA148CPSSIA.

A complete First Alert manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual First Alert FA148CPSSIA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the First Alert FA148CPSSIA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the First Alert FA148CPSSIA, that we can find in the current document
3. Tips how to use the basic functions of the device First Alert FA148CPSSIA - which should help us in our first steps of using First Alert FA148CPSSIA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with First Alert FA148CPSSIA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of First Alert FA148CPSSIA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning First Alert FA148CPSSIA?

Use the form below

If you did not solve your problem by using a manual First Alert FA148CPSSIA, ask a question using the form below. If a user had a similar problem with First Alert FA148CPSSIA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)