Manual Icom IC-7200

19 pages 3.97 mb
Download

Go to site of 19

Summary
  • Icom IC-7200 - page 1

    When the transceiv er is connected to a PC with the USB cable , the f ollowing operations can be performed; • Remote control operation (CI-V : Icom Communica- tion Interf ace-V) by the PC . • Modulation input from the PC. • Received audio output to the PC . T ransceiver PC USB cable (third par ty) NO TE: • PC software (third party) may be r ...

  • Icom IC-7200 - page 2

    2 PROCEDURE Ref er to the f ollowing steps f or the USB driver installation. Bef ore installing the USB driver , log in as the administrator and quit all applications when Windows is run- ning. Overview • System requirements (p . 1) • Item requirements (p . 1) Preparing • Bef ore installing the USB driver (p . 3) Driver installation • Windo ...

  • Icom IC-7200 - page 3

    3 Before installing the USB driver Icom HP giv es the USB driver download service. Bef ore installing the USB driver , download the f ollow- ing compressed file. • USB dr iver (File name: 7200UsbDrv_v100.zip) Icom is not responsible f or any damage or lack of data resulting from the use of the USB driver . PREP ARING ...

  • Icom IC-7200 - page 4

    4 Windows Vista DRIVER INST ALLA TION The displa yed dialogue bo x es, indications or oper- ations ma y differ slightly from the following instr uc- tions according to y our system conditions or envi- ronment. q Make sure that the transceiver is not connected to the PC . w Star t up Windows. • Quit all other application if running. e Double-clic ...

  • Icom IC-7200 - page 5

    5 o After restar ting the PC, connect the transceiver to the PC with the USB cable (third party) as shown below . • Be sure to connect the USB cable correctly and not up- side down. T ransceiver PC USB cable (third par ty) T o USB jack T o USB por t Type A Type B ACC K E Y SEN D AL C REM OT E !0 T urn the transceiver power ON. • “Installing d ...

  • Icom IC-7200 - page 6

    6 The displa yed dialogue bo x es, indications or oper- ations ma y differ slightly from the following instr uc- tions according to y our system conditions or envi- ronment. q Make sure that the transceiver is not connected to the PC . w Star t up Windows. • Quit all other application if running. e Connect the transceiv er to the PC with the USB ...

  • Icom IC-7200 - page 7

    7 Windows XP (Contin ued) DRIVER INST ALLA TION i Select the “Win” f older, then click [OK]. • The folder construction: “7200UsbDrv_v100” ➞ “Driver” ➞ “Win” Click Select o Clic k [Ne xt>]. Click !0 The Wizard star ts searching f or the driver and shows the dialogue below during search. !1 After the dr iver is f ound, the ? ...

  • Icom IC-7200 - page 8

    8 !6 Select “Install from a list or specific location (Adv anced), ” then click [Ne xt>]. Click Select !7 Select “Search f or the best driv er in these locations . ” then select “Include this location in the search:”, and click [Browse]. Click Select Select !8 Select the “Win” f older, then click [OK]. • The folder construction ...

  • Icom IC-7200 - page 9

    9 The displa yed dialogue bo x es, indications or oper- ations ma y differ slightly from the following instr uc- tions according to y our system conditions or envi- ronment. q Make sure that the transceiver is not connected to the PC . w Star t up Windows. • Quit all other application if running. e Connect the transceiv er to the PC with the USB ...

  • Icom IC-7200 - page 10

    10 Windows 2000 (Continued) DRIVER INST ALLA TION o Select “slabb us.inf” in the “Win” folder , then click [Open]. • The folder construction: “7200UsbDrv_v100” ➞ “Driver” ➞ “Win” Select “slabbus .inf ” Click !0 Clic k [OK]. Click !1 When the dr iver is found, the f ollowing dialogue is displa yed. Click [Next>] to s ...

  • Icom IC-7200 - page 11

    11 Windows 2000 (Continued) DRIVER INST ALLA TION !6 Clic k [Browse ...]. Click !7 Select “slabw2k.inf ” in the “Win” f older , then clic k [Open]. • The folder construction: “7200UsbDrv_v100” ➞ “Driver” ➞ “Win” Click Select “slabw2k.inf ” !8 Clic k [OK]. Click !9 When the dr iver is found, the f ollowing dialogue is d ...

  • Icom IC-7200 - page 12

    12 COM PORT CONFIRMA TION Windows Vista q Star t up Windows . w Right click “Computer , ” then select “Proper ties. ” • “Computer” is av ailable in <Start> menu. e “System” screen appears as below . Click [De vice Manager]. Click r In case “User Account Control” dialogue bo x ap- pears as below , click [Contin ue]. Click ...

  • Icom IC-7200 - page 13

    13 DRIVER UNINST ALLA TION The display ed dialogue box es or indications ma y differ slightly from the follo wing instr uctions according to your system conditions, or en vironment. Windows Vista q Star t up Windows . w Select the “Control P anel” in the Star t menu. • The control panel appears as shown in the next step below . e Click the ? ...

  • Icom IC-7200 - page 14

    14 FOR Y OUR REFERENCE COM P ort setting T o ch ange the COM P or t n umber settin g, co nnect the trans ceiv er t o the PC and then turn the tr ansceiv er po wer ON after the driver installation is completed. Windows Vista q Star t up Windows . w Right click “Computer , ” then select “Properties. ” • “Computer” is av ailable in <S ...

  • Icom IC-7200 - page 15

    15 FOR Y OUR REFERENCE COM P or t setting (Continued) Windows XP For Windo ws 2000: Ref er to the f ollowing instructions because the operations of Windows 2000 are similar to Windows XP . q Star t up Windows. w Right click “My Computer , ” then select “Properties. ” • “My Computer” is av ailable in <Start> menu. e “System Pro ...

  • Icom IC-7200 - page 16

    16 FOR Y OUR REFERENCE (Continued) About audio When the transceiv er is connected to a PC with the USB cable (third party), the follo wing oper ations can be perf or med; • Received audio output to the PC . • Modulation input from the PC . The set mode item ‘Modulation input (Data OFF)’ or ‘Modulation input (Data ON)’ must be set as “ ...

  • Icom IC-7200 - page 17

    17 FOR Y OUR REFERENCE About audio (Continued) The modulation input settings T o input the audio sign al from the US B jac k of the t ransceiv er , set t he modulati on input connector as “USB” in the set mode item ‘Modulation input (Data OFF)’ or ‘Modulation input (Data ON)’, or CI-V system (command). • When the data mode is OFF (SSB ...

  • Icom IC-7200 - page 18

    18 FOR Y OUR REFERENCE About audio (Continued) USB level setting Set the input modulation le vel of the USB jac k in the set mode item ‘USB Lev el’ or CI-V system (command). <Set mode> q Push and hold M-CH/RIT SET for 1 sec. twice to enter the set mode. w Rotate [M-CH] to select “ USB L VL . ” e Rotate [DIAL] to set the input modulati ...

  • Icom IC-7200 - page 19

    19 FOR Y OUR REFERENCE (Continued) Specifications Connector type USB B type Interf ace USB 2.0/1.1 P ow er supply Self power The PC cannot recognize the transceiv er when the pow er is OFF . Suppor t OS Windows Vista Windows XP Windows 2000 Serial for CI-V Compliant f or CI-V spec. Asynchronous serial Construction (1 bite) Star t bit : 1 Data bit : ...

Manufacturer Icom Category Computer Drive

Documents that we receive from a manufacturer of a Icom IC-7200 can be divided into several groups. They are, among others:
- Icom technical drawings
- IC-7200 manuals
- Icom product data sheets
- information booklets
- or energy labels Icom IC-7200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Icom IC-7200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Icom IC-7200, service manual, brief instructions and user manuals Icom IC-7200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Icom IC-7200.

Similar manuals

A complete manual for the device Icom IC-7200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Icom IC-7200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Icom IC-7200.

A complete Icom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Icom IC-7200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Icom IC-7200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Icom IC-7200, that we can find in the current document
3. Tips how to use the basic functions of the device Icom IC-7200 - which should help us in our first steps of using Icom IC-7200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Icom IC-7200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Icom IC-7200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Icom IC-7200?

Use the form below

If you did not solve your problem by using a manual Icom IC-7200, ask a question using the form below. If a user had a similar problem with Icom IC-7200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)