Manual ADTRAN MP-118

44 pages 1.82 mb
Download

Go to site of 44

Summary
  • ADTRAN MP-118 - page 1

    ™ MediaPack MP-118 & MP-114 Document #: LTRT-26301 September 2007 Quick Installation Guide Integration with Microsoft ® Office Communications Server 2007 ...

  • ADTRAN MP-118 - page 2

    ...

  • ADTRAN MP-118 - page 3

    Quick Installation Guide Contents Version 5.0 3 September 2007 Table of Contents 1 Introducti on ................................................................................................................. 7 2 Quick St art ................................................................................................................... 9 3 Co ...

  • ADTRAN MP-118 - page 4

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 4 Document #: LTRT-26301 Reader's Notes ...

  • ADTRAN MP-118 - page 5

    Quick Installation Guide Notices Version 5.0 5 September 2007 Notices Notice This Quick Installation Gui de describes the installation an d configuration of Audi oCodes’ Media Pack MP-11x FXO SIP analog media gateways for integratio n with Microsoft ® Office Communications Server 2007. Information contained in this document is believed to be acc ...

  • ADTRAN MP-118 - page 6

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 6 Document #: LTRT-26301 Related Documentation Document # Manual Name LTRT-656xx (e.g., LTRT-65601 MP-11x & MP-124 SIP Release Notes LTRT-654xx MP-11x & MP-124 SIP User's Manual Warning: Ensure that you connect the FXO ports to Central Office (CO) / PBX l ...

  • ADTRAN MP-118 - page 7

    Quick Installation Guide 1. Introduction Version 5.0 7 September 2007 1 Introduction This guide provides step-by-step instructions for quickly setting up AudioCodes' MediaPack (MP-118 and MP-114) Sessi on Initiation Protocol (SIP) voice-over-IP (VoIP) gateways for intermediating between third-party, p rivate bran ch exchange s (PBX) or variou ...

  • ADTRAN MP-118 - page 8

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 8 Document #: LTRT-26301 The AudioCodes' MP-11x FXO gate way can be integrated i n the Office Communications Se rver 2007 / Unified Communications (UC) environm ents, by implementing one of the following o ptions:  One-to-One: each PBX line connected to an FXO ...

  • ADTRAN MP-118 - page 9

    Quick Installation Guide 2. Quick Start Version 5.0 9 September 2007 2 Quick Start This Quick Installation Guide hel ps you setup t he MediaPack gateways for int eroperability with either third-party PBXs or various PSTN interf aces, and Office Comm unications Server 2007. Prior knowledge of IP networks is recom mended. Figure 2-1: Required Steps t ...

  • ADTRAN MP-118 - page 10

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 10 Document #: LTRT-26301 3 Configuring the MediaPack The gateway is supplied with the appli cation softwar e residing on its flash memory (set to fact ory default parameters). Note: This guide a ssumes that the gateway i s running firmware version 5.0. If you are run ...

  • ADTRAN MP-118 - page 11

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 11 September 2007 3.1.2 Navigating the Embedded Web Server The main areas of the Web interface are shown in the figure bel ow. Figure 3-2: MediaPack Web Interface Areas ...

  • ADTRAN MP-118 - page 12

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 12 Document #: LTRT-26301 3.1.3 Changing Login User name and Password It's recommended that you change the d efault user name and password of the Web user a ccount initially used to access the Embedded Web Server. ¾ To change the user name and password, take the ...

  • ADTRAN MP-118 - page 13

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 13 September 2007 3.1.4 Searching for ini file Parameters The Embedded Web Server provides a search engine that allows you to search any ini file parameter that is configurable using the Embedd ed Web Server. The search result p rovides you with a link to the relevant Web page in whi ...

  • ADTRAN MP-118 - page 14

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 14 Document #: LTRT-26301 3.2 Assigning an IP Address to the MediaPack If the gateway's default IP address (refe r to Table 3-1 ) doesn't correspond to the network i n which Office Communications Server 2007 i s installed, you can a ssign a different IP addr ...

  • ADTRAN MP-118 - page 15

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 15 September 2007 Table 3-2: Adding a BootP Client 3. Use the gateway's chassi s reset button to physi cally reset the gateway, cau sing it to use BootP; the gateway changes it s network parameters to the va lues provided by BootP. 3.2.2 Assigning an IP Addr ess Using CLI via RS ...

  • ADTRAN MP-118 - page 16

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 16 Document #: LTRT-26301 3.2.3 Assigning an IP Address using HTT P You can assign an IP address to the gateway using the gateway's Embedd ed Web Server (ba sed on HTTP), by connecting the gateway to a PC with a direct, local Ethernet connection. ¾ To assign an ...

  • ADTRAN MP-118 - page 17

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 17 September 2007 3. Configure the gateway's ‘IP Address’, ‘Subnet Mask’, and ‘Def ault Gateway IP Address’ fields to correspond with your network IP settings of Office Communications Se rver 2007. 4. Click the Reset button, a nd then at the prompt, click OK ; the ga ...

  • ADTRAN MP-118 - page 18

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 18 Document #: LTRT-26301 Notes: • Ensure that you download the corre ct ini file so that your gateway is configured correctly fo r interoperability with the deployed PBX / PSTN. • The gateway configuration for the PBX-S ends-Digits option is similar to the One-to ...

  • ADTRAN MP-118 - page 19

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 19 September 2007 Figure 3-8: Configuration File Screen 4. Click the Browse button, a nd then navigate to t he folder that contains the ini file you want to upload. 5. Select the file, and then click the Open button; the name and path of the file appear in the field beside the Bro ws ...

  • ADTRAN MP-118 - page 20

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 20 Document #: LTRT-26301 3.3.2 Using the Em bedded Web Server You can use the gateway's user-fri endly, Web interface (des cribed in Section 3.1 on page 10 ) to configure the advanced parameters liste d below:  IP address of Mediation Server (refe r to Sectio ...

  • ADTRAN MP-118 - page 21

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 21 September 2007 ¾ To define Mediation Server's IP address, take these 4 steps: 1. Open the ‘Proxy & Registratio n' screen ( Protocol Management menu > Protocol Definition > Proxy & Registratio n ). Figure 3-9: Proxy & Registration Screen 2. From the & ...

  • ADTRAN MP-118 - page 22

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 22 Document #: LTRT-26301 3.3.2.2 Defining Number of FXO Ports Connected to PBX The gateway's FXO port (located on the rear panel), interfaces with the PBX. By default, all the gateway's FXO ports (eight for the MP-1 18; four for the MP-114) are ena bled. Ho ...

  • ADTRAN MP-118 - page 23

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 23 September 2007 3.3.2.3 Defining Voice Coders The gateway communicat es with Mediation Serv er using either the G.711 A-law o r G.711 µ -law coder. You can cha nge the default code r usi ng the gateway's Embedded Web Server. ¾ To define the coder, take these 3 steps: 1. Open ...

  • ADTRAN MP-118 - page 24

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 24 Document #: LTRT-26301 ¾ To configure the Number Manipulat ion tables, take these 4 steps: 1. Open the Number Manipulation sc reen you want to configure ( Protocol Management menu > Manipulation Tables ); the relevant Manipulation table scree n is displayed. Th ...

  • ADTRAN MP-118 - page 25

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 25 September 2007 Table 3-3: Number Manipulation Parameters Description Parameter Description Source IP (Applicable only to the ‘Destination Phone Number Manipulation Table for IP to Tel’) Source IP address of the call (obtaine d from the Contact header in the INVITE message). No ...

  • ADTRAN MP-118 - page 26

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 26 Document #: LTRT-26301 3.3.2.4.2 Number Normalization Examples Two examples are provided belo w for number norm alization. The examples are based on t he following assumptions: a PBX with prefix (local) number 333 and a 4-digit extension number that begins with the ...

  • ADTRAN MP-118 - page 27

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 27 September 2007  Modifying PBX, Local, and National Calls to E.164 Format for Inbound Calls: Inbou nd calls refer to call s received by OCS clie nts connected through IP to the Office Communications Server 2 007. 1. Local calls from the PBX or PSTN: the PBX user only dials a 4-d ...

  • ADTRAN MP-118 - page 28

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 28 Document #: LTRT-26301 3.3.2.5 Defining Answer Supervision When there is a call from Office Communication s Server 2007 to the gateway, the gateway behavior depends on whether or not the Answer Supervi sion feature is enable d. If Answer Supervision is enabled, the ...

  • ADTRAN MP-118 - page 29

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 29 September 2007 3.3.2.6 Defining Automatic Dialing When using the One-to-One option, each PBX line that is connected to an FXO port serves one OCS client. You must define automatic dialing for each FXO port connected to the OCS clien t. ¾ To define Automatic Dialing, take these 4 ...

  • ADTRAN MP-118 - page 30

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 30 Document #: LTRT-26301 3.3.2.7 Enabling Caller ID If the Caller ID service i s enabled, the gateway det ects the Calle r ID signal from the Tel side (PBX / PSTN) and sends it to M ediation Server over IP in t he SIP INVITE message. Therefore, to allow the OCS clien ...

  • ADTRAN MP-118 - page 31

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 31 September 2007 3.3.2.8 Defining SIP Transport Type The procedure below de scribes how to config ur e the SIP transport type. You may need to change the gateway's SIP transport type from UDP (default) to TCP, since this is the transport type us ed by Mediation Server. ¾ To de ...

  • ADTRAN MP-118 - page 32

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 32 Document #: LTRT-26301 3.3.2.9 Defining Disconnect on Broken Connection The procedure below describes how to conf ig ure the Disconnect on Broken Conne ction parameter. Since Mediat ion Server uses Sile nce Suppressio n, it may not send Real-time Transport Protocol ...

  • ADTRAN MP-118 - page 33

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 33 September 2007 3.3.2.10 Defining DTMF Payload Type The procedure belo w describes how to define the dual-tone multi-frequ ency (DTMF) payl oad type. The DTMF payload t ype used by Mediation Se rver is 101. You may need to set this value at the gateway as well. ¾ To define the DTM ...

  • ADTRAN MP-118 - page 34

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 34 Document #: LTRT-26301 3.3.2.11 Enabling One-Stage Dialing One-stage dialing is whe n the gateway receiv es an IP-to-Tel call, off-hoo ks the PBX line connected to the PBX / PSTN telephone, and then immediately dials the destination telephone number. In oth er word ...

  • ADTRAN MP-118 - page 35

    Quick Installation Guide 3. Configuring the MediaPack Version 5.0 35 September 2007 3.3.2.12 Defining Channel Select Mode Channel select mod es determine the m ethod in wh ich new IP-to-Tel calls (i.e., calls from OCS clients to PBX/PSTN phones) are assigned to gatew ay port s (i.e., channels). It is recommended to select the Cyclic Asce nding mode ...

  • ADTRAN MP-118 - page 36

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 36 Document #: LTRT-26301 3.3.2.13 Disabling RTCP Attribute By default, the RTP Control Protocol (RTCP) attribute (EnableRTCPAttribute) is ena bled. However, you need to disable it by usin g the AdminPage of the Embedded Web Server. ¾ To disable the RTCP attribute, t ...

  • ADTRAN MP-118 - page 37

    Quick Installation Guide 4. Backing Up Configuration Settings Version 5.0 37 September 2007 4 Backing Up Configuration Settings Once you have modified configuration settings, it is recom mended you make a backup of the modified configuration file. This is done by saving the modified ini configuration file to a folder on your PC. If you lose your ga ...

  • ADTRAN MP-118 - page 38

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 38 Document #: LTRT-26301 5 Monitoring the Gateway The gateway provides several methods to monitor various operating statuses:  Monitoring the gateway's front-panel cha ssis LEDs ( refer to Se ction 5.1 ).  Monitoring the gateway's channels u sing the ...

  • ADTRAN MP-118 - page 39

    Quick Installation Guide 5. Monitoring the Gateway Version 5.0 39 September 2007 5.2 Monitoring the Channels You can monitor channel s using the gateway' s Embedded Web Server. ¾ To monitor the status of the channels, take this step:  Open the 'Channel Status' screen, by clicking the Ho me icon on the main menu bar. Figure 5-1: C ...

  • ADTRAN MP-118 - page 40

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 40 Document #: LTRT-26301 6 Troubleshooting 6.1 General Troubleshooting The table below lists general troublesho oting that may arise with your gateway. Table 6-1: General Troubleshooting Problem Possible Cause Solution Ready LED is lit red Hardware component failure. ...

  • ADTRAN MP-118 - page 41

    Quick Installation Guide 6. Troubleshooting Version 5.0 41 September 2007 ¾ To configure the Syslog parameters, take these 7 steps: 1. Open the ‘Management S ettings’ screen ( Advanced Configuration menu > Manage ment Settings ); the ‘Management Settings’ screen is di splayed. Figure 6-1: Management Settings Screen 2. In the 'Syslo ...

  • ADTRAN MP-118 - page 42

    MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 42 Document #: LTRT-26301 7 Regulatory Information Declaration of Conformity Application of Counc il Directives: 73/23/EEC (including amendments) 89/336/EEC (including amendments) 1999/5/EC Annex-II of the Directive Standards to which Con formity is Declared: EN55022: ...

  • ADTRAN MP-118 - page 43

    Quick Installation Guide 7. Regulatory Information Version 5.0 43 September 2007 Safety Notices • Installation and service of this unit must only be performed by authorized, qualified service personnel. • The MediaPack FXO Output Tones and DTMF level should not ex c eed -9 dBm (AudioCodes setting #23) in order to comply with FCC 68, TIA/EIA/IS- ...

  • ADTRAN MP-118 - page 44

    ™ MediaPack MP-118 & MP-114 Quick Installation Guide Integration with Microsoft ® Office Communications Server 2007 www.audiocodes.com ...

Manufacturer ADTRAN Category Server

Documents that we receive from a manufacturer of a ADTRAN MP-118 can be divided into several groups. They are, among others:
- ADTRAN technical drawings
- MP-118 manuals
- ADTRAN product data sheets
- information booklets
- or energy labels ADTRAN MP-118
All of them are important, but the most important information from the point of view of use of the device are in the user manual ADTRAN MP-118.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals ADTRAN MP-118, service manual, brief instructions and user manuals ADTRAN MP-118. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product ADTRAN MP-118.

Similar manuals

A complete manual for the device ADTRAN MP-118, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use ADTRAN MP-118 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of ADTRAN MP-118.

A complete ADTRAN manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual ADTRAN MP-118 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the ADTRAN MP-118, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the ADTRAN MP-118, that we can find in the current document
3. Tips how to use the basic functions of the device ADTRAN MP-118 - which should help us in our first steps of using ADTRAN MP-118
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with ADTRAN MP-118
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of ADTRAN MP-118 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning ADTRAN MP-118?

Use the form below

If you did not solve your problem by using a manual ADTRAN MP-118, ask a question using the form below. If a user had a similar problem with ADTRAN MP-118 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)