English dropdown-ico

Manual Craftsman 536.88614

39 pages 1.56 mb
Download

Go to site of 39

Summary
  • Craftsman 536.88614 - page 1

    CRRFTSMRW 5 Horsepower 22 Inch Dual Stage 120V. Electric Start SNOWTHROWER MODEL NO. 536.886140 Caution: Read and follow all Safety Rules and Operating Instructions before first use , of this product. SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. 760996 09/17/97 ...

  • Craftsman 536.88614 - page 2

    Table of Contents 2 Service and Adjustments 17-21 Warranty 2 Storage 22 Safety Rules 2-4 Troubleshooting 23 Contents of Shipping Carton 4-5 Repair Parts 24-32 Assembly 5-8 Engine Repair Parts 33-37 Operation 8-14 Spanish(EspaSol) 38-63 Maintenance 14-16 Parts Ordering/Service Back Cover LIMITED TWO-YEAR WARRANTY ON CRAFTSMAN SNOW THROWER For two ye ...

  • Craftsman 536.88614 - page 3

    , 3. . Disengage all clutches before starting the engine (motor). Do not operate the snow thrower without wearing adequate winter outer garments.Wear footwear that will improve footing on slippery surfaces. Handle fuel with care; it is highly flammable. (a) Use an approved fuel container. (b) Never remove fuel tank cap or add fuel to a running engi ...

  • Craftsman 536.88614 - page 4

    17. Disengage power to the auger/impeller when snow thrower is transportedor not in use. 18, Use onlyattachments and accessories approved by the manufacturer of the snowthrower (such as tire chains, electric start kits, etc.). 19. Never operate the snow thrower without good visibility or light. Always be sure of your footing, andkeepa firm hold on ...

  • Craftsman 536.88614 - page 5

    1- Screw, 5/16-18 x 2 In. _ 5116-18x1.00 In. Parts packed separately in carton (not shown full size) 2 - Ignition Keys (Attached to engine in plastic bag) 1 - container 5W30 oil 1 - container Fuel Stabilizer 1 - Crank Assembly 1 - Snow Chute Assembly CAUTION: Always wear safety glasses or eye shields while assembling snow thrower. TOOLS REQUIRED FO ...

  • Craftsman 536.88614 - page 6

    TO REMOVE SNOW THROWER FROM CARTON • Locate and remove container of 5W30 oil. • Locate all parts packed separately and remove from the carton. NOTE: Place fuel stabilizer in a safe place until needed for storage. • Remove and discard the packing material from around the snow thrower. • Cut all four comers of the carton from top to bottom an ...

  • Craftsman 536.88614 - page 7

    Crank Rod Assembly joint pin Universaljoint Bracket TO INSTALL SHIFTER LEVER KNOB • Thread the 1/2-13 hexjam nut found in the parts bag onto shifter lever. Thread the shifter lever knob onto the threaded end of the shifter lever until it is snug against the hexjam nut and the lip is pointed away from the engine. Tighten hexjam nut against the bot ...

  • Craftsman 536.88614 - page 8

    HOW TO SET UP YOUR SNOW THROWER • Your snow thrower is equipped with height adjust skids (see second figure on page 5) on the outside of the auger housing. To adjust the skid height for different conditions, (see To Adjust Skid Height paragraph on page 17). ,/ CHECKLIST Before you operate your new snow thrower, toensure that you receive the best ...

  • Craftsman 536.88614 - page 9

    KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Engine Engine Off Choke On Fast Slow Stop Fuel Oil Primer Start Run Button Dr ...

  • Craftsman 536.88614 - page 10

    The operation of any snow thrower can re- sult in foreign objects being thrown into the eyes, which can result in severe eye dam- age. Always wear safety glasses or eye shields while operating the snow thrower. We recommend standard safety glasses or a wide vision safety mask for over your glasses, available at Craftsman Retail Stores or Service Ce ...

  • Craftsman 536.88614 - page 11

    • For ease of maneuverability in light snow conditions, disconnect the klick pin from the wheel locked position and push into the single wheel drive (klick pin through axle hole only) position (see figure below). • Make sure that the klick pin is in the single wheel drive position of the axle only and not through the locked position. Klick Pin ...

  • Craftsman 536.88614 - page 12

    Make sure to wipe up any spilled fuel be- fore starting the engine. Store gasoline in a clean, approved con- tainer and keep the cap in place on the container. TO STOP ENGINE • To stop engine, move the throttle control lever to O (STOP) position and remove key. Keep the key in a safe place. The engine will not start without the key. NOTE: DO NOT ...

  • Craftsman 536.88614 - page 13

    COLD START • Be sure the auger drive and traction drive levers are in the disengaged (released) position. • Move the throttle control to '_ (FAST) position. See figure on page 9 for loca- tion. • Remove the keys from the plastic bag. In- sert one key into the ignition slot. Be sure it snaps into place. DO NOT TURN KEY. Keep the second ke ...

  • Craftsman 536.88614 - page 14

    snow blowing is accomplished when the snow is removed immediately after it falls. • For complete snow removal, slightly over- lap each path previously taken. Use more overlap in deep snow to prevent overloading. • The snow should be discharged down wind whenever possible. In windy condi- tions, lower the chute deflector to direct discharged sno ...

  • Craftsman 536.88614 - page 15

    GENERALRECOMMENDATIONS The warranty on this snow thrower does not cover items that have been subjected to op- erator abuse or negligence. To receive full value from the warranty, the operator must maintain the snow thrower as instructed in this manual. The maintenance chart is pro- vided to assist the operator in properly maintaining the snow throw ...

  • Craftsman 536.88614 - page 16

    LUBRICATION • Hex Shaft and Gears - Hex shaft and gears require no lubrication. All bearings and bushings are lifetime lubricated and require no maintenance. NOTE: Any greasing or oiling of the above components can cause contamination of the friction wheel. If the disc drive plate or friction wheel comes in contact with grease or oil, damage to t ...

  • Craftsman 536.88614 - page 17

    Z_ CAUTION: Always disconnect the spark plug wire and tie back away from the plug before making any adjustments or repairs. TO ADJUST SKID HEIGHT This snow thrower is equipped with two height adjustment skids, located on the out- side of the auger housing (see figure be- low). These skids elevate the front of the snow thrower. Nuts O _r Housing Hei ...

  • Craftsman 536.88614 - page 18

    AUGER DRIVE BELT If your snow thrower will not discharge snow, and the auger drive belt (see figure below) is damaged, replace it as follows: Traction Auger Drive Belt Pulley .=r Drive Pulley Drive Belt • Hold the square end of the threaded per- Idler tion with pliers and adjust the Iocknut in or out until the excess slack is removed. Aug_ Pulley ...

  • Craftsman 536.88614 - page 19

    • Check clutch control cable adjustment, see page 17. • Reconnect spark plug wire. TRACTION DRIVE BELT If your snow thrower will not move forward, check the traction drive belt (see second figure on page 18) for wear (Check other causes also in the Trouble Shooting Points section). If the traction drive belt needs to be replaced, proceed as fol ...

  • Craftsman 536.88614 - page 20

    If adjustment is necessary: • Loosen bolts in speed selector lever (see figure below). Speed Selector Lever / TO REPLACE FRICTION WHEEL If the snoW thrower will not move forward, and the friction wheel is worn or damaged, you need to replace it as follows: (First allow the engine to cool). • Drain the gasoline from the fuel tank. • Drain the ...

  • Craftsman 536.88614 - page 21

    TO ADJUSTCARBURETOR If you think your carburetor needs adjusting, see your nearest Authorized Craftsman Service Center. Engine performance should not be affected at altitudes up to 7,000 feet. For operation at higher elevations, contact your Authorized Craftsman Service Center. IMPORTANT: Never tamper with the engine governor, which is factory set ...

  • Craftsman 536.88614 - page 22

    ,/_ CAUTION: Never store your snow thrower indoors or in an enclosed, poorly ventilated area if gasoline remains in the tank. fumes may reach an open flame, spark or pilot light from a fumace, water heater, clothes dryer, cigarette, etc. To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below. SNOW THROWE ...

  • Craftsman 536.88614 - page 23

    TROUBLE CAUSE CORRECTION Difficult starting Defective spark plug Replace defective plug Water or dirt in fuel system Use carburetor bowl drain to flush and refill with fresh fuel Engine runs er- Blocked fuel line or low on fuel Clean fuel line; check fuel sup- ratically ply; add fresh gasoline (gaso- line/oil mixture if 2-cycle engine) Engine stall ...

  • Craftsman 536.88614 - page 24

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 ELECTRIC START ASSEMBLY REF NO. PART NO, 6 330783 7 6216 8 6217 9 6219 760996 PART NAME Motor, Electric Starter Screw, 1/4-20x.50 Screw #6-32x2.50 Cord, Starter Motor Owner's Manual EnQ/Sp 319051B i¾. ENGINE ASSEMBLY .J @ REF NO. _ARTNO. PARTNAME 10 ENGINE 12 710024 13 120638 31 3949 33 120 ...

  • Craftsman 536.88614 - page 25

    CRAFTSMAN 22" -5H.P. SNOW THROWER 536.886140 FRAME ASSEMBLY 0 @ 0 o ® ...' REF. NO. 80 88 90 91 100 103 104 ; 105 106 107 108 109 110 112 115 342573A PART NO. 340578-833 780055 583031-853 310169 761195 761198 710200 41529 340682 340579 761153 340869 180124 313843 41529 PART NAME Frame Assembly Screw, 5/16-18x.50 Tap. Panel, Bottom Screw, ...

  • Craftsman 536.88614 - page 26

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 DRIVE ASSEMBLY 190 191 192 215 249 246 224 229 250 ;244 REF, NO. 190 191 192 193 195 196 198 210 211 215 216 217 221 222 223 224 225 226 227 228 229 230 235 "'. 240 270 PART NAME PART NO. 579941 313853 137185 313919 579937 11871 782585 583163-853 583206 583155 85501 71074 73811 580969 438 ...

  • Craftsman 536.88614 - page 27

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 GEAR CASE ASSEMBLY ® ® ® REF. NO. 300 301 303 304 305 306 310 311 312 313 314 315 PART NO. 10577 10576 710025 46931 303008 9344 9566 50304 48275 340284 51279 51405 PART NAME Gear Case, RH Gear Case, LH Screw, 1/4-20x.75 Nut, 1/4-20 Mac-Lock Nut, 1/4-20 Hexkeps Screw, 3/8-16x.50 Tap. Oil Seal Bea ...

  • Craftsman 536.88614 - page 28

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 AUGER HOUSING ASSEMBLY @ @ REF NO. 480 481 482 485 490 491 493 499 5O0 502 504 ! 505 1 506 ! 510 511 514 520 521 PART NO. 583124 577400 71371 334514 582960 43846 180077 710026 760811-833 309235 71003 120382 1499 581395-853 340714 780285 340520-853 340525-853 PART NAME Pulley, V4L Screw 5/16-18x.63 ...

  • Craftsman 536.88614 - page 29

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 DISCHARGE CHUTE ASSEMBLY REF. NO. 582 583 584 588 592 593 594 595 596 597 ,598 599 BOO 500-1 PART NO. 340720 12021 71038 6711 12021 6711 120393 120638 120393 13527 120376 126358 760990-853 760989 PART NAME Carr. Bolt 5/16-18x.75 Washer, Plastic Nut, 5/16-18 hexnylon PlasticWasher Plastic Washer Pla ...

  • Craftsman 536.88614 - page 30

    @ CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 HANDLE ASSEMBLY @ @ REF, NO. 720 724 725 726 727 728 730 731 733 734 739 741 743 PART NO. 9552-853 11234 120393 120638 120376 11261 334195 334195 4140 3535 4049 1579 579869 PART NAME Upper Handle Screw, 5/16-18x2.75 Flatwasher .344x.69x.065 Washer, HvspUk N_, 5/16-18 Reghex Stop, Red Pla_c Kit fo ...

  • Craftsman 536.88614 - page 31

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 WHEEL ASSEMBLY EF.I _O. ' PART NO. _50 580883 r 852 583012 853 73839 654 782585 555 581730 656 579857 671 73840 i, , PART NAME Shaft, Axle Wheel/mid Sprkt'& Hub Assy. Screw 14-20x2.25 Nut, "J/4-20Reghxctdk Bearing, Flanged Chain, Roller #42x40P Flatwasher .765x1.12x.06 REF. NO. P ...

  • Craftsman 536.88614 - page 32

    CRAFTSMAN 22" - 5H.P. SNOW THROWER 536.886140 CHUTE CONTROL ROD ASSEMBLY REF NO. 85O 854 855 856 860 661 862 863 864 PART NO. 585426 307399 309312 578159 71457 148 308145 124829 120394 PART NAME Crank Assy, Whjoke Chute Crank Handle Flatwasher, .39x.70x.35 Ring, Ret. E. Eye Bolt 3/8-16x5.00 Grommet Eye Bolt Boot, Eye Bolt Chute Crank Nut, 3/8- ...

  • Craftsman 536.88614 - page 33

    CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.985003 CARBURETOR 640084 z_ _ '' ' REF. 1 2 _6 7 10 14 15 16 17 18 2O 20A 25 27 28 29 30 31 32 33 38 37 40 44 47 48 _D-,,,37 PART# 631615 331767 640070 650506 632108 631815 630735 631807 651025 630766 640018 640053 631951 631024 632019 631028 631021 631022 27136A 27554 632735 632547 640085 27 ...

  • Craftsman 536.88614 - page 34

    CRAFTSMAN 4-CYCLE ENGINE MODEE NUMBER 143.985003 > 34 ...

  • Craftsman 536.88614 - page 35

    CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.985Cq3 EF. 4 5 6 7 8 9 0 5 5A 6 6A 0 0 0 0 .1 ,2 ,2 _2 _3 _5 _6 _8 r9 _0 _0 ;4 ;4A 55 39 r0 r5 30 31 32 33 36 39 ]0 )2 )3 100 101 102 103 110 I10A 119 120 125 125 126 126 127 130 PART# I I 36469A I _R727 I 30969 I 28277 I 31334 I 31335 I 651018 I 314_ I 32600 I 36552 I 35883 I 6508021 6509261 34740 36073 36 ...

  • Craftsman 536.88614 - page 36

    STARTER NO. 590742 REF. PART# PART NAME 590742 3 590740 6 590616 7 590617 : 8 590645A 11 590647 12 590535 13 590574 14 590741 STARTER, REWIND RETAINER DOG, STARTER SPRING, DOG PULLEY & REWIND SPRING ASSY IHOUSING ASSY, STARTER ROPE, STARTER (LENGTH 98"& 9/64"DIA.) HANDLE, STARTER LOCKING TAB 36 ...

  • Craftsman 536.88614 - page 37

    CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143,985003 STARTER NO. 33290E REF. PART# PART NAME 0 1 2 3 4 5 6 7 8 9 10A 13 14 15 16A 24 25 27A 30 31 33290E 31749 33522 33769 33524 35911 35461 35450 35912 0 35452A 590500 33441 35453 35454 35462 35456 650819 32450B 650759 ELECTRIC STARTER (110 VOLT) RETAINER RING SPRING RETAINER ANTI-DRIFT SPRING NUT & ...

  • Craftsman 536.88614 - page 38

    ...

  • Craftsman 536.88614 - page 39

    For the repair or replacement parts you need delivered directly to your home Call 7 am-7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio -1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) Para pedir servicio de reparaci6n a domicili ...

Manufacturer Craftsman Category Snow Blower

Documents that we receive from a manufacturer of a Craftsman 536.88614 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 536.88614 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 536.88614
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 536.88614.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 536.88614, service manual, brief instructions and user manuals Craftsman 536.88614. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 536.88614.

Similar manuals

A complete manual for the device Craftsman 536.88614, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 536.88614 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 536.88614.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 536.88614 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 536.88614, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 536.88614, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 536.88614 - which should help us in our first steps of using Craftsman 536.88614
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 536.88614
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 536.88614 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 536.88614?

Use the form below

If you did not solve your problem by using a manual Craftsman 536.88614, ask a question using the form below. If a user had a similar problem with Craftsman 536.88614 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)