English dropdown-ico

Manual QSC AD-S282H

16 pages 2.12 mb
Download

Go to site of 16

Summary
  • QSC AD-S282H - page 1

    *TD-000148-00* TD-000148-00 rev .B High-power T wo-way Multi-Use Loudspeaker • two 8-inch (203mm) neodymium magnet low-frequency drivers • 1-inch throat compre ssion high-frequency driver • yoke mount I-282H Speakon ® input, pole cup, and floor -mount sw ivel feet. Bi-amp capable, 8 ohm AD-S282H bi-amp capable, 8 ohm AD-S282HT 70V/100V trans ...

  • QSC AD-S282H - page 2

    2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS 1- Read these instructio ns. 2- Keep these instructio ns. 3- Heed all warnings. 4- Follow all instructio ns. 5- Clean only with a dry c loth. 6- Install in accordance with QSC Audio Product’ s instructions and a lice nsed, professional enginee r . 7- Do not install near a ny heat sources ...

  • QSC AD-S282H - page 3

    3 Introduction Thank you and congratulations on your purchase of the I-282H, AD-S282H, or AD-S282HT multi-use, weather resistant loudspeakers. These products represent the state-of-the-art in lightweight sound reinforcement loudspeaker systems. T o get the most from your investment, we encourage you to review this manual carefully . These loudspeak ...

  • QSC AD-S282H - page 4

    4 Coverage Angles Before mounting the loudspeaker , determine the mounting orientation and desired coverage angles. As supplied from the factory , the loudspeak er’ s coverage angles are 90° (horizontal) x 60° (vertical) with the cabinet oriented vertically . The waveguide can be rotated to interchange the coverage angles. Rotating the Waveguid ...

  • QSC AD-S282H - page 5

    5 Mounting IMPORT ANT! ENSURE THA T THE LOUDSPEAKER IS MOUNTED PROPERL Y AND A SAFETY CABLE IS INST ALLED TO RET AIN THE LOUDSPEAKER IN THE EVENT OF A MOUNT- ING FAILURE. CO NSUL T A LICENSED, PROFESSIONAL ENGI- NEER WHEN ANY DOUBT OR QUESTIONS ARISE REGARDING A PHYSICAL EQUIPMENT INS T ALLA TION. Safety Cable Attachment (all models) On the back of ...

  • QSC AD-S282H - page 6

    6 Input Connection Cover (AD-S282H/HT models) The loudspeaker includes a weather resistant cover for the input terminals. If using the cover , be sure to pass the wiring through the bushing nut, bushing, cover , and gasket before making connections.The input wiring cover is keyed to fit one way only! Be sure the keyed end is oriented toward the bot ...

  • QSC AD-S282H - page 7

    7 Connection I-282H P ASSIVE: Set the BI-AMP / PA S S I V E selector switch to PA S S I V E . Con- nect the full-range + input signal to Speakon pin 1+ and the full range - input signal to Speakon pin 1-. The two Speakon connectors wired in paral- lel, allowing a second I-282H loudspeaker (also set for PA S S I V E operation) to be connected direct ...

  • QSC AD-S282H - page 8

    8 Specifications- AD-S282H (passive), AD-S282HT , I-282H (passive) Frequency Range: 80- 27.7k Hz (-6 dB, free field response) 60- 29.5k Hz (-10 dB, free field response) Maximum Output 2 : 119dB SPL continuous rms output (calculated) 125dB SPL peak output (calculated) Impedance: 8 ohms nominal 5.5 minimum at 17.6k Hz 64.2 maximum at 2.56k Hz Power R ...

  • QSC AD-S282H - page 9

    9 Specifications- AD-S282H and I-282H with Recommended Signal Processing Low Frequency Drivers ( parallel) High Frequency Driver Frequency Range: 70- 2.1k Hz (-6 dB, free field response) 2. 1k- 24.0k Hz (-6 dB, free field response) 60- 2.7k Hz (-10 dB, free field response) 1.9k- 24.0k Hz (-10 dB, free field response) Power Rating: 400W (8 hrs., IEC ...

  • QSC AD-S282H - page 10

    10 Dimensions Specifications are subj ect to change witho ut notice. ...

  • QSC AD-S282H - page 11

    11 Frequency (Hertz) Frequency (Hertz) SPL Impedance SPL (dB) SPL (dB) Impedance (ohms) On-axis Response and Impedance Vs. Frequency , Passive I-282H, AD-S282H, and AD-S282HT Beam width, Response, and Impedance Curves Specifications are subjec t to change without noti ce. Impedance (ohms) LF SPL HF SPL LF Impedance HF Impedance On-axis Response and ...

  • QSC AD-S282H - page 12

    12 Frequency (Hertz) Frequency (Hertz) Horizontal V er tical Beamwidth (degrees) On Axis 15° Off Axis 30° Off Axis Response On-Axis, 15° , 30°,4 5°, and 60° Off-Axis Vs. Frequency Horizontal and V ertical Beamwidth Vs. Frequen cy I-282H, AD-S282H, and AD-S282HT Beamwi dth and On/Off Axis Response Curves Specifications are subjec t to change w ...

  • QSC AD-S282H - page 13

    13 Painting the Loudspeaker The loudspeaker enclosure, grill, and mount can be painted to matc h any decor , provided the following precautions are observed. The cabinet is made of high impact polystyrene which requires c ontrolled painting procedures in order to obtain good results. U se a paint “system” designed for high impact polystyrene fr ...

  • QSC AD-S282H - page 14

    14 Notes: ...

  • QSC AD-S282H - page 15

    15 Notes: ...

  • QSC AD-S282H - page 16

    QSC Audio Products, Inc. 1675 MacArthur Boul evard Costa Mesa, California 92626 USA ©2004, 2006 “QSC” and the QSC logo are register ed with the U.S. Patent and T rademark Office. Mailing address / Dirección postal / Adresse postale / 通信地址 : QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T eleph one Num ...

Manufacturer QSC Category Portable Speaker

Documents that we receive from a manufacturer of a QSC AD-S282H can be divided into several groups. They are, among others:
- QSC technical drawings
- AD-S282H manuals
- QSC product data sheets
- information booklets
- or energy labels QSC AD-S282H
All of them are important, but the most important information from the point of view of use of the device are in the user manual QSC AD-S282H.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals QSC AD-S282H, service manual, brief instructions and user manuals QSC AD-S282H. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product QSC AD-S282H.

Similar manuals

A complete manual for the device QSC AD-S282H, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use QSC AD-S282H by users. Manuals are usually written by a technical writer, but in a language understandable to all users of QSC AD-S282H.

A complete QSC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual QSC AD-S282H - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the QSC AD-S282H, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the QSC AD-S282H, that we can find in the current document
3. Tips how to use the basic functions of the device QSC AD-S282H - which should help us in our first steps of using QSC AD-S282H
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with QSC AD-S282H
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of QSC AD-S282H in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning QSC AD-S282H?

Use the form below

If you did not solve your problem by using a manual QSC AD-S282H, ask a question using the form below. If a user had a similar problem with QSC AD-S282H it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)